H3C S5800-56C-PWR, S5800-56C, S5800-32C, S5800-32C-PWR User Manual

H3C S5800 Series Ethernet Switches

Installation Manual

Hangzhou H3C Technologies Co., Ltd.

Manual Version: 5W101-20090604

No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of Hangzhou H3C Technologies Co., Ltd.

Trademarks

Notice

H3C, , Aolynk, , H3Care, SecPro, SecPoint, SecEngine, SecPath, Comware, Secware, Storware, NQA, VVG, V

, TOP G, , IRF, NetPilot, Neocean, NeoVTL,

G, VnG, PSPT, XGbus, N-Bus, TiGem, InnoVision and HUASAN are trademarks of Hangzhou H3C Technologies Co., Ltd.

All other trademarks that may be mentioned in this manual are the property of their respective owners.

The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this document do not constitute the warranty of any kind, express or implied.

About This Manual

Organization

H3C S5800 Series Ethernet Switches Installation Manual is organized as follows:

Chapter Contents

1 Product Overview

2 Installation Preparations

3 Installing a Switch

4 Initial Power-On

5 Loading Software

6 Maintenance and Troubleshooting

Appendix

Conventions

Briefly introduces the appearance, system description, as well as the features and applications of the H3C S5800 series switches.

Describes the requirements on installation site, the safety recommendations before and during installation, and the required tools.

Covers the procedures for installing the H3C S5800 series, ground wire connection, power module installation, interface module installation, and so on.

Helps you get familiar with the basic knowledge of how to boot and configure the H3C S5800 series, including device startup, power-on, and initialization of system files, and so on.

Introduces how to loading application files and upgrading the Boot ROM program by using the host software package.

Introduces how to maintain software and hardware of the H3C S5800 series.

Appendix A: Lightning protection of the H3C S5800 series switch. Appendix B: Obtaining Support for your Product.

The manual uses the following conventions:

GUI conventions

Convention Description

< > Button names are inside angle brackets. For example, click <OK>.

[ ]

Window names, menu items, data table and field names are inside square brackets. For example, pop up the [New User] window.

Multi-level menus are separated by forward slashes. For example, [File/Create/Folder].

Symbols

Convention Description

Means reader be extremely careful. Improper operation may cause bodily injury.

Means reader be careful. Improper operation may cause data loss or damage to equipment.

Means a complementary description.

Documentation

Go to the following columns for different categories of product documentation: [Products & Solutions]: Provides information about products and technologies, as well as solutions. [Technical Support & Document > Technical Documents]: Provides several categories of product

documentation, such as installation, configuration, and maintenance. [Technical Support & Document > Software Download]: Provides the documentation released with the

software version.

Technical Support

customer_service@h3c.com http://www.h3c.com

At http://www.h3cnetworks.com

Documentation

Select Drivers & Downloads in the Support area. Select Documentation for Type of File and select Product Category.

Technical Support

Please see the appendix Obtaining Support for Your Product.

Documentation Feedback

You can e-mail your comments about product documentation to info@h3c.com. We appreciate your comments.

Environmental Protection

This product has been designed to comply with the requirements on environmental protection. For the proper storage, use and disposal of this product, national laws and regulations must be ob served.

Table of Contents

1 Product Overview······································································································································1-1

Overview ·················································································································································1-1 S5800-60C-PWR ····································································································································1-4

Front Panel ······································································································································1-4 Rear Panel·······································································································································1-5

S5800-56C ··············································································································································1-6

Front Panel ······································································································································1-6 Rear Panel·······································································································································1-7

S5800-56C-PWR ····································································································································1-8

Front Panel ······································································································································1-8 Rear Panel·······································································································································1-8

S5800-32C ··············································································································································1-9

Front Panel ······································································································································1-9 Rear Panel·······································································································································1-9

S5800-32C-PWR ··································································································································1-10

Front Panel ····································································································································1-10 Rear Panel·····································································································································1-10

S5800-32F ············································································································································1-11

Front Panel ····································································································································1-11 Rear Panel·····································································································································1-12

Ports······················································································································································1-12

Console Port··································································································································1-12 Management Ethernet Port ···········································································································1-13 USB Interface ································································································································1-13 10/100/1000Base-T Ethernet Port·································································································1-13 100/1000Base-X SFP Interface·····································································································1-13 SFP+ Interface·······························································································································1-15

LEDs······················································································································································1-17

System Status LED ·······················································································································1-17 Hot Swappable Power Module Status LEDs·················································································1-18 RPS Status LED ····························································································································1-18 Port Mode LED ······························································································································1-19 Seven-Segment LED·····················································································································1-19 10/100/1000Base-T Auto-Sensing Ethernet Port Status LED·······················································1-20 100/1000Base-X SFP Interface Status LED ·················································································1-21 SFP+ Interface Status LED ···········································································································1-22 Management Ethernet Port Status LED ························································································1-22 OAP Card Status LED ···················································································································1-22 PoE Module Status LED················································································································1-23

Interface Card Status LED ············································································································1-23 Hot Swappable Power Modules············································································································1-23 Hot Swappable Fan Trays ····················································································································1-25 Interface Cards······································································································································1-26

OAP Card··············································································································································1-27 Hot Swappable PoE Module ·················································································································1-27

2 Installation Preparations···························································································································2-1

Safety Precautions ··································································································································2-1 Installation Site········································································································································2-1

Temperature/Humidity·····················································································································2-1

Cleanness········································································································································2-2

Electromagnetic Susceptibility·········································································································2-2

Laser Safety ····································································································································2-2 Installation Tools ·····································································································································2-3

3 Installing a Switch ·····································································································································3-1

Installation Flow of the Switch·················································································································3-2 Installing the Switch into a 19-Inch Rack Using Mounting Brackets·······················································3-2

Introduction to Mounting Brackets and Cable Management Brackets ············································3-3

Attaching the Mounting Brackets to a Switch··················································································3-4

Mounting the Switch to a Rack········································································································3-6 Mounting the Switch on a Workbench ····································································································3-7 Connecting the Ground Wire ··················································································································3-8

When a Grounding Strip is Available·······························································································3-8

Where a Grounding Conductor Can be Buried ·············································································3-10

In Other Installation Sites ··············································································································3-10 Installing a Power Module·····················································································································3-12

Installing the Power Module ··········································································································3-12

Removing the Power Module ········································································································3-14 Connecting the Power Cord··················································································································3-14

Connecting an AC Power Cord ·····································································································3-15

Connecting an RPS DC Power Cord·····························································································3-16

Connecting a Power Cord to the PSR150-A/PSR150-D·······························································3-18

Connecting a Power Cord to the PSR300-12A/PSR300-12D1·····················································3-19

Connecting a Power Cord to the PSR750-A&PSR750-D ·····························································3-21 Installing an Interface Card ···················································································································3-24

Installing an Interface Card ···········································································································3-24

Removing an Interface Card ·········································································································3-25 Installing an OAP Card··························································································································3-26

Installing an OAP Card to the Switch ····························································································3-26

Removing an OAP Card················································································································3-27 Installing a PoE Module ························································································································3-28

Installing a PoE Module·················································································································3-28

Removing the PoE module············································································································3-28 Verifying the Installation························································································································3-29

4 Initial Power-On ·········································································································································4-1

Setting Up the Configuration Environment······························································································4-1 Connecting the Console Cable ···············································································································4-1

Console Cable ·································································································································4-1

Connection Procedure·····················································································································4-2 Setting Terminal Parameters ··················································································································4-2 Booting the Switch ··································································································································4-5

Checking Before Power-On·············································································································4-5

Powering On the Switch ··················································································································4-5

Changing the Boot Mode·················································································································4-7

5 Loading Software·······································································································································5-1

Introduction ·············································································································································5-1 Approaches for Loading Software···········································································································5-1 Loading Software Through the Boot ROM Menu····················································································5-2

Introduction to the Boot ROM Menu································································································5-2

Loading Software Using XMODEM Through Console Port·····························································5-4

Loading Software Using TFTP Through Ethernet Port ·································································5-11

Loading Software Using FTP Through Ethernet Port····································································5-15 Loading Software Through CLI ·············································································································5-18

Loading Software Through USB Interface·····················································································5-18

Loading Software Using FTP ········································································································5-19

Loading Software Using TFTP ······································································································5-20

6 Maintenance and Troubleshooting··········································································································6-1

Software Loading Failure ························································································································6-1 Password Loss········································································································································6-1

User Password Loss························································································································6-1

Boot ROM Password Loss ··············································································································6-1 Power Module Failure ·····························································································································6-2

Fixed Power Module Failure············································································································6-2

Hot Swappable Power Module Failure ····························································································6-3 OAP Card Failure····································································································································6-5 Hot Swappable PoE Module Failure ·······································································································6-5 Fan Failure ··············································································································································6-5

Fixed Fan Failure·····························································································································6-6

Hot Swappable Fan Tray Failure·····································································································6-6 Configuration Terminal Failure················································································································6-8

iii

1 Product Overview

Overview

H3C S5800 Series Ethernet Switches (hereinafter referred to as the S5800 series) are Layer 3 Gigabit

Ethernet switching products developed by Hangzhou H3C Technologies Co., Ltd. (hereinafter referred

to as H3C). The S5800 series provide abundant service features. They provide the IPv6 forwarding

function and 10 GE uplink interfaces. Through H3C-specific cluster management, you can simplify

network management.

The S5800 series are designed as distribution or access devices for intranets and metropolitan area

networks (MANs). Supporting IPv4/IPv6 dual stack, the S5800 series provide abundant service

features and routing functions and can also be used for connecting server groups in data centers.

The S5800 series support the innovative Intelligent Resilient Framework (IRF) technology. With IRF,

multiple S5800 switches can be interconnected as a logical entity to form a new intelligent network

featuring high availability, scalability, and manageability.

The S5800 series support H3C Open Application Architecture (OAA) platform. To enable features such

as firewall, anti-virus, IPS, and wireless access control on the switches, you only need to insert OAP

cards into the switches and configure these features on the OAP cards.

The S5800 series include the following models, and have the system specifications as shown in

1-1.

z S5800-60C-PWR

z S5800-56C

z S5800-56C-PWR

z S5800-32C

z S5800-32C-PWR

z S5800-32F

Table 1-1 The S5800 series system specifications

Item

Dimensions (H × W × D)

S5800-60C-

PWR

86.1 × 440 × 465 mm (3.39 × 17.32 × 18.31 in.)

S5800-56C

43.6 × 440 × 367 mm (1.72 ×

17.32 ×

14.45 in.)

S5800-56C-

PWR

43.6 × 440 × 427 mm (1.72 ×

17.32 ×

16.81 in.)

S5800-32C

43.6 × 440 × 367 mm (1.72 ×

17.32 ×

14.45 in.)

S5800-32

C-PWR

43.6 × 440 × 427 mm (1.72 ×

17.32 ×

16.81 in.)

Table

S5800-3

43.6 × 440 × 427 mm (1.72 ×

17.32 ×

16.81 in.)

Weight

18 kg

(39.68 lb)

6.5 kg

(14.33 lb)

8.5 kg

(18.74 lb)

1-1

6.0 kg

(13.23 lb)

8 kg

(17.64 lb)

8.5 kg

(18.74 lb)

Item

Console port

Manageme nt Ethernet port

USB interface

10/100/100 0Base-T Ethernet ports

100/1000Ba se-X SFP interfaces

S5800-60C-

PWR

S5800-56C

S5800-56C-

PWR

S5800-32C

S5800-32

C-PWR

S5800-3

z The console port of the S5800-60C-PWR, S5800-32C or S5800-32C-PWR is

available on the front panel.

z The console port of the S5800-56C, S5800-56C-PWR or S5800-32F is available

under the logo panel on the front panel.

1, on the

— — — — —

rear panel

1 (full speed)

z The USB interface of the S5800-60C-PWR, S5800-32C or S5800-32C-PWR is

available on the front panel.

z The USB interface of the S5800-56C, S5800-56C-PWR or S5800-32F is available

under the logo panel on the front panel.

Supports PoE

—

4 — — — — 24

SFP+ interfaces

Number of supported interface cards

Interface card models supported (optional)

OAP card

Hot swappable PoE module

4. You can plug an SFP+ transceiver, SFP transceiver or SFP+ cable

—

into the SFP interface. An SFP interface plugged in with an SFP+ cable can be used to connect IRF devices.

2, on the front panel

1, on the rear panel

1, on the

rear panel

1, on the rear panel

1, on the front panel

LSW1SP4P0 (provides four 1 Gbps/10 Gbps SFP+ interfaces, which can be used to connect IRF member devices)

LSW1SP2P0 (provides two 1 Gbps/10 Gbps SFP+ interfaces, which can be used to connect IRF member devices)

LSW1GP16P0 (provides sixteen 1000 Mbps SFP interfaces)

LSW1GT16P (provides sixteen 1000 Mbps Ethernet electrical interfaces)

IPS card

Firewall card

Access

—

controller module

LSW148POE M

—

Fan

Hot swappable fan tray (LSW1FAN)

Fixed fans Fixed fans Fixed fans Fixed fans

1-2

Hot swappa ble fan tray (LSW1B FAN)

Item

Supported hot swappable power modules

RPS power module supported

Input volta ge

S5800-60C-

PWR

S5800-56C

S5800-56C-

PWR

PSR300-12A

PSR300-12D 1

— — — —

PSR750-A

PSR750-D

RPS1000-A3 RPS800-A

RPS1000-A 3

Rated voltage: 100 VAC to 240 VAC, 50/60 Hz

Max voltage: 90 VAC to 264 VAC, 47/63 Hz

Rated voltage:

z 300 W

DC: –48 VDC to –60 VDC

z 750 W

— — — —

DC: –54 VDC to –57 VDC

S5800-32C

RPS800-A

S5800-32

C-PWR

RPS1000A3

S5800-3

PSR150

-A

PSR150

-D

RPS800

-A

Rated voltage: –48 VDC to –60 VDC

RPS

Power consumptio n

Power consumptio n (full configuratio n)

Rated voltage: –52 VDC to –55 VDC

DC: 94 W

AC: 96 W

Single DC output: 1840 W (1500 W for PoE output)

Dual DC outputs: 1840 W (1500 W for PoE output)

Single AC output: 714 W (425 W for PoE output)

Dual AC outputs: 1147 W (740 W for PoE output)

Rated voltage: 10.8 VDC to 13.2 VDC

102 W

163 W

Rated voltage: –52 VDC to –55 VDC

DC: 107 W

AC: 131 W

DC: 973 W (740 W for PoE output)

AC: 673 W (370 W for PoE output)

Rated voltage: 10.8 VDC to 13.2 VDC

67 W

105 W

Rated voltage: –52 VDC to –55 VDC

DC: 64 W

AC: 85 W

DC: 870 W (740 W for PoE output)

AC: 598 W (370 W for PoE output)

Rated voltage: –52 VDC to –55 VDC

DC: 58 W

AC: 67 W

DC: 136 W

AC: 146 W

Operating temperature

0°C to 45°C (32°F to 113°F)

1-3

Item

S5800-60C-

Operating humidity (nonconden

10% to 90%

sing)

S5800-60C-PWR

Front Panel

Figure 1-1 S5800-60C-PWR front panel

PWR

S5800-56C

S5800-56C-

PWR

S5800-32C

S5800-32

C-PWR

S5800-3

(1) Interface card 1 (2) Interface card 2 (3) 10/100/1000Base-T auto-sensing Ethernet port status LED

(4) Seven-segment LED

(5) Port mode LED (6) Console port (7) USB interface (8) System status LED (SYS) (9) Hot swappable power module 1 status LED (PWR1)

(10) Hot swappable power module 2 status LED (PWR2)

(11) OAP card status LED (SLOT3) (12) PoE module status LED (SLOT4)

(13) 100/1000Base-X SFP interface status LED (14) Port status LED mode switching button

(15) 100/1000Base-X SFP interface

(16) 10/100/1000Base-T auto-sensing Ethernet port

z The S5800-60C-PWR provides two interface card slots on its front panel. Each slot is installed with

a filler panel when the switch is shipped. The above figure illustrates a switch with two

LSW1SP4P0 interface cards.

z You can select one or two interface cards for your switch as needed. See Interface Cards on page

1-26 for the interface card models supported by the S5800 series, and see Installing an Interface

on page 3-24 for the installation of interface modules. See H3C S5820X & S5800 Series

Card

Ethernet Switches Interface Cards User Manual for the detailed description of the interface

modules.

1-4

Rear Panel

Figure 1-2 S5800-60C-PWR rear panel

(1) OAP card filler panel (2) PoE module (3) Grounding screw (4) Filler modules (5) Hot swappable power module 1 (6) Hot swappable power module 2 (7) Hot swappable fan tray

z The S5800-60C-PWR provides two power module slots on its rear panel. Hot swappable power

module slot 1 is empty when the switch is shipped, and hot swappable power module 2 is installed

with a filler panel. The above figure illustrates a switch with two PSR300-12A AC power modules.

z You can select one or two power modules for your switch as needed. See Hot Swappable Power

Modules

on page 1-23 for the power module models supported by the S5800-60C-PWR, and see

Installing a Power Module on page 3-12 for the installation of power modules. See H3C

PSR300-12A & PSR300-12D1 Power Modules User Manual and H3C PSR750-A & PSR750-D Power Modules User Manual for the detailed description of the power modules.

z The S5800-60C-PWR provides a PoE module slot on its real panel. The slot is installed with a filler

panel when the switch is shipped. You can install a PoE module on your switch as needed.

z The S5800-60C-PWR provides an OAP card slot on its rear panel. The slot is installed with a filler

panel when the switch is shipped. You can install an OAP card (firewall card, IPS card or access

controller module) on your switch as needed. For supported OAP card models, refer to

on page

1-27; for how to install an OAP card, refer to Installing an OAP Card on page 3-26.

OAP Card

1-5

S5800-56C

Front Panel

Figure 1-3 S5800-56C front panel

(1) 10/100/1000Base-T auto-sensing Ethernet port

(2) 10/100/1000Base-T auto-sensing Ethernet port status LED

(3) Seven-segment LED (4) Port mode LED

(5) SFP+ interface status LED

(6) Logo panel (A console port and a USB interface

are under this logo panel) (7) System status LED (SYS) (8) RPS status LED (RPS) (9) Interface card status LED (SLOT1) (10) SFP+ interface (11) Port status LED mode switching button

To use the console port and USB interface, open the logo panel.

Figure 1-4 S5800-56C logo panel I

(1)

When opening or closing the logo panel, follow these steps to avoid damage to the logo panel:

z Insert your finger into the notch on the right side of the logo panel to open it. Do not try to open the

logo panel from any other parts.

z The logo panel is attached to the chassis through a rubber strip on its left. Swing the logo panel

within the elasticity of the rubber strip. Do not pull or swing the logo panel with excessive force;

otherwise, the rubber strip may fall off or be broken.

z Before pushing in the logo panel, make sure that the pin on the left of the logo panel is engaged

with the slot on the front panel. Then engage the tab on the right of the logo panel into the slot on

the chassis, and then press the logo panel until the tab clicks into the slot. If the tab is not engaged

into the slot, do not press the logo panel with excessive force to avoid damage to the tab.

1-6

Figure 1-5 S5800-56C logo panel II

(1) Tab of the logo panel (2) Pin of the logo panel (3) Console port (4) USB interface (5) Slot on the front panel (6) Rubber strip

Rear Panel

Figure 1-6 S5800-56C rear panel

(1) Bail latch (2) RPS receptacle protective cover (3) Grounding screw (4) Interface card (5) AC receptacle

z The S5800-56C provides one interface card slot on its rear panel. The slot is installed with a filler

panel when the switch is shipped. The above figure illustrates a switch with one LSW1SP4P0

interface card.

z You can select an interface card for your switch as needed. See Interface Cards on page 1-26 for

the interface card models supported by the S5800 series, and see

3-24 for the installation of interface modules. See H3C S5820X & S5800 Series Ethernet

page

Installing an Interface Card on

Switches Interface Cards User Manual for the detailed description of the interface modules.

1-7

S5800-56C-PWR

Front Panel

Figure 1-7 S5800-56C-PWR front panel

(1) 10/100/1000Base-T auto-sensing Ethernet port (3) Seven-segment LED (4) Port mode LED

(5) SFP+ interface status LED

(7) System status LED (SYS) (8) RPS status LED (RPS)

(9) Interface card status LED (SLOT1) (10) SFP+ interface

(11) Port status LED mode switching button

(2) 10/100/1000Base-T auto-sensing Ethernet port status LED

(6) Logo panel (A console port and a USB interface are under this logo panel)

To use the console port and USB interface, open the logo panel, as shown in

Rear Panel

Figure 1-8 S5800-56C-PWR rear panel

(1) RPS receptacle (2) Bail latch (3) Grounding screw (4) Interface card (5) AC receptacle

Figure 1-4 and Figure 1-5.

z The S5800-56C-PWR provides one interface card slot on its rear panel. The slot is installed with a

filler panel when the switch is shipped. The above figure illustrates a switch with one LSW1SP4P0

interface card.

z You can select an interface card for your switch as needed. See Interface Cards on page 1-26 for

the interface card models supported by the S5800 series, and see

3-24 for the installation of interface modules. See H3C S5820X & S5800 Series Ethernet

page

Installing an Interface Card on

Switches Interface Cards User Manual for the detailed description of the interface modules.

1-8

S5800-32C

Front Panel

Figure 1-9 S5800-32C front panel

(1) 10/100/1000Base-T auto-sensing Ethernet port (3) SFP+ interface status LED (4) Console port (5) USB interface (6) Seven-segment LED (7) Port mode LED (8) System status LED (SYS)

(9) RPS status LED (RPS) (10) Interface card status LED (SLOT1)

(11) Port status LED mode switching button (12) SFP+ interface

(2) 10/100/1000Base-T auto-sensing Ethernet port status LED

Rear Panel

Figure 1-10 S5800-32C rear panel

(1) Bail latch (2) RPS receptacle protective cover (3) Grounding screw (4) Interface card (5) AC receptacle

z The S5800-32C provides one interface card slot on its rear panel. The slot is installed with a filler

panel when the switch is shipped. The above figure illustrates a switch with one LSW1SP4P0

interface card.

z You can select an interface card for your switch as needed. See Interface Cards on page 1-26 for

the interface card models supported by the S5800 series, and see

3-24 for the installation of interface modules. See H3C S5820X & S5800 Series Ethernet

page

Installing an Interface Card on

Switches Interface Cards User Manual for the detailed description of the interface modules.

1-9

S5800-32C-PWR

Front Panel

Figure 1-11 S5800-32C-PWR front panel

(1) 10/100/1000Base-T auto-sensing Ethernet port (3) SFP+ interface status LED (4) Console port (5) USB interface (6) Seven-segment LED (7) Port mode LED (8) System status LED (SYS)

(9) RPS status LED (RPS) (10) Interface card status LED (SLOT1)

(11) Port status LED mode switching button (12) SFP+ interface

Rear Panel

Figure 1-12 S5800-32C-PWR rear panel

(1) RPS receptacle (2) Bail latch (3) Grounding screw (4) Interface card (5) AC receptacle

(2) 10/100/1000Base-T auto-sensing Ethernet port status LED

z The S5800-32C-PWR provides one interface card slot on its rear panel. The slot is installed with a

filler panel when the switch is shipped. The above figure illustrates a switch with one LSW1SP4P0

interface card.

z You can select an interface card for your switch as needed. See Interface Cards on page 1-26 for

the interface card models supported by the S5800 series, and see

3-24 for the installation of interface modules. See H3C S5820X & S5800 Series Ethernet

page

Installing an Interface Card on

Switches Interface Cards User Manual for the detailed description of the interface modules.

1-10

S5800-32F

Front Panel

Figure 1-13 S5800-32F front panel

(1) Interface card 1 (2) 100/1000Base-X SFP interface (3) 10/100/1000Base-X SFP interface status LED (5) Port mode LED (6) SFP+ interface status LED (7) Logo panel (A console port and a USB interface are under this logo panel) (9) Hot swappable power module 1 status LED (PWR1)

(11) SFP+ interface (12) Port status LED mode switching button

(4) Seven-segment LED

(8) System status LED (SYS)

(10) Hot swappable power module 2 status LED (PWR2)

To use the console port and USB interface, open the logo panel, as shown in

Figure 1-4 and Figure 1-5.

z The S5800-32F provides one interface card slots on its front panel. The slot is installed with a filler

panel when the switch is shipped. The above figure illustrates a switch with one LSW1SP4P0

interface card.

z You can select an interface card for your switch as needed. See Interface Cards on page 1-26 for

the interface card models supported by the S5800 series, and see

3-24 for the installation of interface modules. See H3C S5820X & S5800 Series Ethernet

page

Installing an Interface Card on

Switches Interface Cards User Manual for the detailed description of the interface modules.

1-11

Rear Panel

Figure 1-14 S5800-32F rear panel

(1) (2)

(3)

(5)(4)

(6)(7)

(1) Hot swappable power module 1 (2) Hot swappable power module 2 (3) Hot swappable fan tray (4) Management Ethernet port (5) Grounding screw (6) Management Ethernet port ACT status LED (7) Management Ethernet port LINK status LED

z The S5800-32F provides two power module slots on its rear panel. Hot swappable power module

slot 1 is empty when the switch is shipped, and hot swappable power module 2 is installed with a

filler panel. The above figure illustrates a switch with two PSR150-A AC power modules.

z You can select one or two power modules for your switch as needed. See Hot Swappable Power

Modules

on page 1-23 for the power module models supported by the S5800-32F, and see

Installing a Power Module on page 3-12 for the installation of power modules. See H3C PSR150-A

& PSR150-D Power Modules User Manual for the detailed description of the power modules.

Ports

Console Port

Each S5800 series provides one console port on the front panel. Table 1-2 describes the console port

specifications.

Table 1-2 Console port specifications

Connector type

Compliant standard

Transmission baud rate

Service

Item Specification

RJ-45

EIA/TIA-232

9600 bps to 115200 bps (defaulting to 9600 bps)

z It can be connected to an ASCII terminal. z It can be connected to a serial port of a local or remote (through a pair of

modems) PC running terminal emulation program.

1-12

Management Ethernet Port

The S5800-32F provides a management Ethernet port on its rear panel. The port connects to a

computer to perform system program loading and debugging without being affected by the switching

chip working status; or connects to a remote network management station (NMS) to implement remote

management of the system.

Table 1-3 S5800-32F management Ethernet port specifications

Item Specification

Connector type RJ-45

Connector quantity 1

Port transmission rate 10/100/1000 Mbps half duplex, full duplex

Transmission medium and maximum transmission distance

Function and service Host software and Boot ROM upgrade, network management

USB Interface

Each S5800 series provides a USB2.0 interface compliant with the OHC standard on the front panel.

The USB interface supports an upload and download speed of 12 Mbps. With this USB interface, you

can access the file system on the flash of the switch to upload or download application and

configuration files.

10/100/1000Base-T Ethernet Port

Each S5800 series (except the S5800-32F) provides 10/100/1000Base-T Ethernet ports on its front

Table 1-4 describes the specifications of the 10/100/1000Base-T Ethernet ports.

panel.

Table 1-4 S5800 series 10/100/1000Base-T Ethernet port specifications

Item Specification

Category-5 twisted pair cable, with a maximum transmission distance of 100 m (328.1 ft.)

Connector type

Interface standard

Max transmission distance

RJ-45

z 10 Mbps, full duplex z 100 Mbps, full duplex z 1000 Mbps, full duplex z MDI/MDI-X, auto-sensing

100 m (328.1 ft.)

Transmission medium Category-5 unshielded twisted pair cable

Standard

IEEE 802.3i, 802.3u, 802.3ab

100/1000Base-X SFP Interface

The S5800-60C-PWR/S5800-32F provides 100/1000Base-X SFP interfaces on its front panel. You can

select the FE or GE SFP transceivers described in

Table 1-5.

1-13

Table 1-5 Transceivers supported by the S5800 series 10/100/1000Base-X SFP interfaces

Max

Transceiver

type

Transceiver

Central

wavelength

Connect

Fiber

transmis

sion

distance

GE SFP transceiver

SFP-GE-SX-MM850-A 850 nm

SFP-GE-LX-SM1310-A

1310 nm

SFP-GE-LH40-SM1310

SFP-GE-LH40-SM1550

1550 nm

SFP-GE-LH70-SM1550

SFP-GE-L X-SM1310

-BIDI

Note that these two transceive

TX: 1310 nm

RX: 1490 nm

r models

SFP-GE-L X-SM1490

-BIDI

should be used in pairs.

TX: 1490 nm

RX: 1310 nm

50/125 µm multimode optical fiber

62.5/125 µm multimode optical fiber

9/125 µm single mode optical fiber

550 m (1804.5 ft)

275 m (902.2 ft)

10 km (about

6.2 mi)

40 km (about

24.9 mi)

40 km (about

24.9 mi)

70 km (about

43.5 mi)

10 km (about

6.2 mi)

FE SFP transceiver

SFP-GE-T — RJ-45

Twisted pair cable

62.5/125 µm

SFP-FE-SX-MM1310-A

multimode optical fiber

9/125 µm single

SFP-FE-LX-SM1310-A

1310 nm

mode optical fiber

9/125 µm single

SFP-FE-LH40-SM1310

mode optical fiber

9/125 µm single

SFP-FE-LH80-SM1550 1550 nm

mode optical fiber

SFP-FE-L X-SM1310

-BIDI

SFP-FE-L X-SM1550

-BIDI

Note that these two transceive r models should be used in pairs.

TX: 1310 nm

RX: 1550 nm

TX: 1550 nm

RX: 1310 nm

9/125 µm single mode optical fiber

100 m (328.1 ft)

2 km (about

1.2 mi)

15 km (about

9.3 mi)

40 km (about

24.9 mi)

80 km (about

49.7 mi)

15 km (about

9.3 mi)

1-14

z You are recommended to use SFP transceivers of H3C on the S5800 series.

z The types of SFP transceivers may update with time. For information about transceivers, contact

H3C technical support or marketing staff.

z For the models and specifications of each kind of transceivers, refer to H3C Low End Series

Ethernet Switches Pluggable Modules Manual.

SFP+ Interface

Each S5800 series (except the S5800-60C-PWR) provides four fixed SFP+ interfaces on its front panel.

You can plug SFP+ transceiver, SFP transceiver or SFP+ cables into the SFP interfaces as needed,

increasing the networking flexibility.

Table 1-6 Transceivers and cables supported by SFP+ interfaces

Transceive

r/Cable

type

GE SFP transceiver

Transceiver/Cable

Central

wavelength

SFP-GE-SX-MM850-A 850 nm

SFP-GE-LX-SM1310A

1310 nm

SFP-GE-LH40-SM131 0

SFP-GE-LH40-SM155 0

1550 nm

SFP-GE-LH70-SM155 0

Connect

Fiber

50/125 µm multimode optical fiber

62.5/125 µm multimode optical fiber

9/125 µm single mode optical fiber

Max

transmis

sion

distance

550 m (1804.5 ft)

275 m (902.2 ft)

10 km (about 6.2 mi)

40 km (about

24.9 mi)

40 km (about

24.9 mi)

70 km (about

43.5 mi)

SFP-GELX-SM13 10-BIDI

SFP-GELX-SM14 90-BIDI

Note that these two transceive r models should be used in pairs.

TX: 1310 nm

RX: 1490 nm

TX: 1490 nm

RX: 1310 nm

1-15

9/125 µm single mode optical fiber

10 km (about 6.2 mi)

Transceive

r/Cable

type

10 GE SFP+ transceiver

Short-haul 10 GE SFP+ cable

Transceiver/Cable

Central

wavelength

SFP-XG-SX-MM850-A 850 nm

SFP-XG-LX220-MM13 10

1310 nm

SFP-XG-LX-SM1310

LSWM1STK

LSWM2STK

— — SFP+ cable

LSWM3STK

Connect

Fiber

50/125 µm multimode optical fiber

62.5/125 µm multimode optical fiber

9/125 µm single mode optical fiber

Max

transmis

sion

distance

300 m (984.3 ft.)

220 m (721.8 ft.)

10 km (about 6.2 mi)

0.65 m (2.1 ft.)

1.2 m (3.9 ft.)

3 m (9.8 ft.)

z You are recommended to use SFP and SFP+ transceivers of H3C on the S5800 series.

z The types of SFP and SFP+ transceivers may update with time. For information about transceivers,

contact H3C technical support or marketing staff.

z For the models and specifications of each kind of transceivers, refer to H3C Low End Series

Ethernet Switches Pluggable Modules Manual.

The S5800 series support the Intelligent Resilient Framework (IRF) feature, where physical

connections are required among members. You can use SFP+ cables to connect the SFP+ interfaces.

SFP+ cables support the SFP+ standard and use 10 G SFP+ Cu standard cables.

H3C provides three types of SFP+ cables with various lengths. See

Table 1-6 for the specifications and

Figure 1-15 for the appearance.

Figure 1-15 SFP+ cable

(1) Connector (2) Handle

1-16

LEDs

Table 1-7 LEDs

LED Device support Description

System status LED All series

Hot swappable power module LED

S5800-60C-PWR and S5800-32F

See

System Status LED on

1-17.

page

See

Module Status LEDs 1-18.

Hot Swappable Power

on page

RPS status LED

Port mode LED All series

Seven-segment LED All series

10/100/1000Base-T auto-sensing Ethernet port status LED

100/1000Base-X SFP interface status LED

SFP+ interface status LED

Management Ethernet port status LED

OAP card status LED S5800-60C-PWR

PoE module status LED S5800-60C-PWR

All series (except S5800-60C-PWR and S5800-32F)

All series (except S5800-32F)

S5800-60C-PWR and S5800-32F

All series (except S5800-60C-PWR)

S5800-32F

See

RPS Status LED on page

1-18.

See

Port Mode LED on page

1-19.

See

Seven-Segment LED on

1-19.

page

See 10/100/1000Base-T

Auto-Sensing Ethernet Port Status LED

See

100/1000Base-X SFP Interface Status LED 1-21.

See

SFP+ Interface Status LED

on page

See Management Ethernet

Port Status LED

See

OAP Card Status LED on

page

See

PoE Module Status LED

on page

on page 1-20.

1-22.

1-23.

on page

on page 1-22.

Interface card status LED

System Status LED

The system status LED helps you determine the working status of the switch. Refer to Table 1-8 for the

details.

Table 1-8 S5800 series system status LED description

LED Status Description

SYS

All series (except S5800-60C-PWR and S5800-32F)

Steady green The switch is started normally.

Flashing green (1 Hz) The system is performing power-on self test (POST).

Steady red POST failed.

Flashing yellow (1 Hz) POST on some ports failed.

Off The switch is powered off.

See

Interface Card Status LED

on page

1-23.

1-17

Hot Swappable Power Module Status LEDs

The hot swappable power module status LEDs help you determine the working status of a hot

swappable power module. Refer to

Table 1-9 Description of the hot swappable power module LEDs

LED Status Description

Table 1-9 for details.

PWR1

PWR2

RPS Status LED

The RPS status LED helps you determine the working status of the RPS of the switch.

For the RPS status LED on an S5800-32C and S5800-56C, refer to

For the RPS status LED on an S5800-32C-PWR and S5800-56C-PWR, refer to

Steady green

Steady yellow

Off

Steady green

Steady yellow

Off

Hot swappable power module slot 1 is installed with a power module, and the power output is normal.

Hot swappable power module slot 1 is installed with a power module, but an output failure occurs.

No power module is installed in hot swappable power module slot 1, or no power is input.

Hot swappable power module slot 2 is installed with a power module, and the power output is normal.

Hot swappable power module slot 2 is installed with a power module, but an output failure occurs.

No power module is installed in hot swappable power module slot 2, or no power is input.

Table 1-10 for details.

Table 1-11 for details.

Table 1-10 Description of the RPS status LED on an S5800-32C and S5800-56C

LED Status Description

Steady green

RPS

Table 1-11 Description of the RPS status LED on an S5800-32C-PWR and S5800-56C-PWR

LED Status Description

RPS

Steady yellow

Off RPS interface is not connected.

Steady green

Steady yellow

Off Power input on the RPS interface is abnormal.

Power input on the RPS interface is normal or the RPS is in position, and AC input on the AC power interface is normal.

Power input on the RPS interface is normal, but AC input fails or AC input is not connected.

Power input on the RPS interface and AC input on the AC power interface are normal.

Power input on the RPS interface is normal, but AC input fails or AC input is not connected.

1-18

Port Mode LED

The port mode LED on the S5800 series can display the working status of a port for you to obtain more

device information. You can use the port mode switching button to change the status of the port mode

LED.

Table 1-12 Port mode LED description

LED Status Description

Steady green Indicates port rate.

Mode

Seven-Segment LED

The seven-segment LED and the system status LED together indicate the operating status of the

device. For details, refer to

Table 1-13 Seven-segment LED description (1)

LED

Unit

System

status

LED

(SYS)

Flashing green

Flashing red

Flashing green

Steady red

Flashing green (1 Hz) (supported by PoE switches only)

Indicates port PoE power supply.

Steady yellow Indicates port duplex mode.

Table 1-13.

Status

Seven-segment LED

The LED displays the specific numbers one by one.

The LED flashes the specific numbers.

A bar rotates clockwise around the LED.

The LED flashes and displays F.

Description

POST running. The LED displays the POST test ID.

POST failed. The LED flashes the POST test ID of the failed test.

Software loading

Fan failure

Steady red

Steady green

The LED flashes and displays t.

The LED displays C.

The LED displays S.

1-19

Over-temperature alarm

The current switch is the command switch in the cluster.

The current switch is a member switch in the cluster.

Status

LED

System

status

LED

Description

Seven-segment LED

(SYS)

The LED displays c.

The current switch is a candidate switch in the

The LED displays the specific numbers.

cluster.

The member ID of the current switch (A stands for 10).

The seven-segment LED, the system status LED, and the port mode LED on the S5800-60C-PWR,

S5800-56C-PWR or S5800-32C-PWR that supports PoE can display the PoE power consumption

percentage of the switch. For details, refer to

Table 1-14.

Table 1-14 Seven-segment LED description (2)

LED status

LED

Port mode

LED

System status

LED

Seven-segment

LED

Description

The LED displays the

Unit

Flashing green (1 Hz) (PoE mode)

Steady green

specific signs.

81 - 100% 61 - 80% 41 - 60% 21 - 40% 0 - 20%

10/100/1000Base-T Auto-Sensing Ethernet Port Status LED

The port mode LED and the 10/100/1000Base-T auto-sensing Ethernet port status LED together

indicate the port operation status. Refer to

Table 1-15 10/100/1000Base-T auto-sensing Ethernet port LEDs description

Status

Port mode

LED

Ethernet port status

LED

Steady green

Table 1-15 for details.

Description

The port operates at a rate of 1000 Mbps; the LED is fast flashing when data is being sent and/or received on the port.

For example, when the

LED displays the sign, it indicates that the PoE power currently provided by the switch occupies 0 to 20% of the total PoE power that the switch can provide.

Steady green (rate mode)

The port operates at a rate of 10/100 Mbps; the LED is

Steady yellow

fast flashing when data is being sent and/or received on the port.

Flashing yellow (3 Hz) POST failed on the port.

Off No link is present on the port.

1-20

Status

Port mode

LED

Ethernet port status

LED

Description

Steady green PoE power supply is normal.

Flashing green (1 Hz) (PoE mode,

Flashing green (3 Hz)

exceeds the upper limit of the power supply consumption of the port, or the available power of the switch is not enough for power supply of the port.

supported by

Power consumption of the device connected to the port

PoE switches

Steady yellow PoE failure, and power supply failed.

only)

Flashing yellow (3 Hz) POST failed on the port.

Off The port does not provide PoE power.

The port operates in full-duplex mode; the LED is fast

Steady green

flashing when data is being sent and/or received on the port.

Steady yellow (duplex mode)

Steady yellow

The port operates in half-duplex mode; the LED is fast flashing when data is being sent and/or received on the port.

Flashing yellow (3 Hz) POST failed on the port.

Off No link is present on the port.

100/1000Base-X SFP Interface Status LED

The port mode LED and the 100/1000Base-X SFP interface status LED together indicate the SFP

interface operation status. Refer to

Table 1-16 for details.

Table 1-16 100/1000Base-X SFP interface status LEDs description

Status

Port mode

LED

Steady green

Ethernet port

status LED

Steady green

Steady yellow

The port operates at a rate of 1000 Mbps; the LED is fast flashing when data is being sent and/or received on the port.

The port operates at a rate of 100 Mbps; the LED is fast flashing when data is being sent and/or received on the port.

Description

(rate mode)

Flashing yellow (3 Hz)

POST failed on the port.

Off No link is present on the port.

The port operates in full-duplex mode; the LED is fast flashing when data is being sent and/or received on the port.

POST failed on the port.

Steady yellow (duplex mode)

Steady green

Flashing yellow (3 Hz)

Off No link is present on the port.

1-21

SFP+ Interface Status LED

The port mode LED and the SFP+ interface status LED together indicate the SFP+ interface operation

status. For details, refer to

Table 1-17 SFP+ interface status LEDs description

Status

Port mode

LED

SFP+ interface

status LED

Table 1-17.

Description

The port operates at a rate of 10 Gbps; the LED is fast flashing when data is being sent and/or received on the port.

The port operates at a rate of 1 Gbps; the LED is fast flashing when data is being sent and/or received on the port.

POST failed on the port.

The port operates in full-duplex mode; the LED is fast flashing when data is being sent and/or received on the port.

POST failed on the port.

Steady green (rate mode)

Steady yellow (duplex mode)

Steady green

Steady yellow

Flashing yellow (3 Hz)

Off No link is present on the port.

Steady green

Flashing yellow (3 Hz)

Off No link is present on the port.

Management Ethernet Port Status LED

The S5800-32F provides two management Ethernet port status LEDs (LINK and ACT) on its rear panel.

Table 1-18 describes the status LEDs.

Table 1-18 The S5800-32F management Ethernet port status LEDs description

Mark Status Description

Off The management Ethernet port is not connected.

LINK

Steady green

ACT

Off The management Ethernet port is not receiving or sending data.

Flashing yellow The management Ethernet port is receiving or sending data.

OAP Card Status LED

The S5800-60C-PWR provides one OAP card status LED (SLOT3) on its front panel. For details, refer

Table 1-19.

The management Ethernet port operates at a rate of 10/100/1000 Mbps.

1-22

+ 80 hidden pages