H3C LS-S5600-26F, LS-S5600-50C-OVS, S5600-26C, S5600-26C-PWR, S5600-26F Installation Manual

H3C S5600 Series Ethernet Switches

Installation Manual

Hangzhou H3C Technologies Co., Ltd.
http://www.h3c.com

Manual Version: T2-08045W-20071218-C-1.04

Copyright © 2006-2007, Hangzhou H3C Techn ologies Co ., Ltd. a nd its licensors

All Rights Reserved

No part of this manual may be reproduced or transmitted in any form or by any means
without prior written consent of Hangzhou H3C Technologies Co., Ltd.

Trademarks

H3C, , Aolynk, , H3Care,

, TOP G, , IRF, NetPilot,
Neocean, NeoVTL, SecPro, SecPoint, SecEngine, SecPath, Comware, Secware,
Storware, NQA, VVG, V

2

G, VnG, PSPT, XGbus, N-Bus, TiGem, InnoVision and

HUASAN are trademarks of Hangzhou H3C Technologies Co., Ltd.
All other trademarks that may be mentioned in this manual are the property of their

respective owners.

Notice

The information in this document is subject to change without notice. Every effort has
been made in the preparation of this document to ensure accuracy of the content s, but
all statements, information, and recommendations in this document do not constitute
the warranty of any kind, express or implied.

To obtain the latest information, please access:
http://www. h3c.com

Technical Support

[e-mail]
http://www. h3c.com

About This Manual

Related Documentation

In addition to this manual, each H3C S5600 Series Ethernet Switches documentation
set includes the following:

Manual Description

H3C S5600 Series Ethernet Switches
Operation Manual

It is used for assisting the users in data
configurations and typical applications.

H3C S5600 Series Ethernet Switches
Command Manual

It is used for assisting the users in using
various commands.

Organization

H3C S5600 Series Ethernet Switches Installation Manual is organized as follows:

Chapter Contents

1 Product Overview

Introduces the characteristics and technical
specifications of S5600 Series Ethernet
Switches.

2 Preparing for Installation

Introduces the installation preparation and
precaution of S5600 Series Ethernet Switches.

3 Installing the Switch

Introduces the procedures to install an S5600
Series Ethernet Switch, including the setup of
the mainframe, cards and cables.

4 Starting up the Switch at the
Initial Boot

Introduces the booting process of an S5600
Series Ethernet Switch, including the power-on
booting of the switch and the system
initialization.

5 Loading Boot ROM and Host
Software

Introduces how to load BootROM and host
software for an S5600 Series Ethernet Switch.

6 Maintenance and
Troubleshooting

Introduces the problems that might occur during
the installation and the booting of an S5600
Series Ethernet Switch and the related solution.

7 Appendix A Lightning
Protection of the Switch

Introduces lightning protection of S5600 Series
Ethernet Switches.

Conventions

The manual uses the following conventions:

I. GUI conventions

Convention Description

< >

Button names are inside angle brackets. For example, click
<OK>.

[ ]

Window names, menu items, data table and field names
are inside square brackets. For example, pop up the [New
User] window.

/

Multi-level menus are separated by forward slashes. For
example, [File/Create/Folder].

II. Symbols

Convention Description

Warning

Means reader be extremely careful. Improper operation
may cause bodily injury.

Caution

Means reader be careful. Improper operation may cause
data loss or damage to equipment.

 Note Means a complementary description.

Environmental Protection

This product has been designed to comply with the requirements on environmental
protection. For the proper storage, use and disposal of this product, national laws and
regulations must be observed.

Installation Manual
H3C S5600 Series Ethernet Switches Table of Contents

i

Table of Contents

Chapter 1 Product Overview........................................................................................................1-1

1.1 Overview............................................................................................................................1-1

1.2 S5600-26C/S5600-26C-PWR/S5600-26F Ethernet Switch ..............................................1-2

1.2.1 Front Panel.............................................................................................................. 1-2

1.2.2 Rear Panel ............................................................................................................ 1-10

1.3 S5600-50C/S5600-50C-PWR Ethernet Switch ............................................................... 1-11

1.3.1 Front Panel............................................................................................................ 1-11

1.3.2 Rear panel.............................................................................................................1-12

1.4 Power system .................................................................................................................. 1-13

1.5 Cooling system ................................................................................................................ 1-13

1.6 Attributes of 1000 Mbps SFP port....................................................................................1-14

1.7 Expansion Module...........................................................................................................1-15

1.8 S5600 Series Technical Specifications ...........................................................................1-18

Chapter 2 Preparing for Installation............................................................................................2-1

2.1 Safety Precautions............................................................................................................. 2-1

2.2 Installation Site...................................................................................................................2-1

2.2.1 Temperature/Humidity.............................................................................................2-1

2.2.2 Cleanness ............................................................................................................... 2-2

2.2.3 Electromagnetic Susceptibility ................................................................................ 2-2

2.2.4 Laser Safety............................................................................................................2-3

2.3 Installation Tools................................................................................................................ 2-3

Chapter 3 Installing the Switch.................................................................................................... 3-1

3.1 Rack-Mounting the Switch................................................................................................. 3-1

3.1.1 Introduction to mounting ear ................................................................................... 3-1

3.1.2 Introduction to guide rail..........................................................................................3-2

3.1.3 Use front mounting ears and a tray......................................................................... 3-3

3.1.4 Use front and rear mounting ears ........................................................................... 3-4

3.1.5 Use front mounting ears and guide rails................................................................. 3-7

3.2 Mounting the Switch on a Tabletop/Workbench................................................................ 3-9

3.3 Installing/Removing the Power Module...........................................................................3-10

3.3.1 Installing the Power Module.................................................................................. 3-10

3.3.2 Removing the Power Module................................................................................ 3-10

3.4 Connecting the Power Cord and the Ground Wire.......................................................... 3-11

3.4.1 Connecting the AC-Input Power Cord................................................................... 3-11

3.4.2 Connecting the DC-Input Power Cord ..................................................................3-12

3.4.3 Connecting the Ground Wire.................................................................................3-13

3.5 Connecting the Switch to a Console Terminal................................................................. 3-16

Installation Manual
H3C S5600 Series Ethernet Switches Table of Contents

ii

3.5.1 Console Cable....................................................................................................... 3-16

3.5.2 Connecting the Console Cable ............................................................................. 3-16

3.6 Installing/Removing the Stack Cable............................................................................... 3-17

3.6.1 Stack Cable........................................................................................................... 3-17

3.6.2 Installing the Stack Cable......................................................................................3-17

3.6.3 Removing the Stack Cable....................................................................................3-18

3.7 Installing/Removing the Optional Interface Module......................................................... 3-18

3.8 Verifying Installation......................................................................................................... 3-19

Chapter 4 Starting up the Switch at the Initial Boot .................................................................. 4-1

4.1 Setting up a Configuration Environment............................................................................4-1

4.2 Connecting the Console Cable.......................................................................................... 4-1

4.3 Setting Terminal Parameters............................................................................................. 4-1

4.4 Booting the Switch.............................................................................................................4-4

4.4.1 Verifying Installation before Power-up .................................................................... 4-4

4.4.2 Powering up the Switch........................................................................................... 4-4

Chapter 5 Loading Boot ROM and Host Software ..................................................................... 5-1

5.1 Introduction to Loading Approaches..................................................................................5-1

5.2 Loading Software Locally...................................................................................................5-1

5.2.1 Boot Menu............................................................................................................... 5-1

5.2.2 Loading Software from Console Port Using XModem............................................5-3

5.2.3 Loading Software from an Ethernet Port Using TFTP ............................................ 5-7

5.2.4 Loading Software from an Ethernet Port Using FTP...............................................5-9

5.3 Loading Software Remotely.............................................................................................5-10

5.3.1 Loading Software Remotely Using FTP................................................................5-10

5.3.2 Loading Software Remotely Using TFTP..............................................................5-11

Chapter 6 Maintenance and Troubleshooting............................................................................ 6-1

6.1 Dealing with Loading Failures............................................................................................6-1

6.2 Dealing with Password Loss..............................................................................................6-1

6.3 Dealing with Power System Failures.................................................................................6-1

6.4 Dealing with Configuration System Failures......................................................................6-1

Installation Manual
H3C S5600 Series Ethernet Switches Chapter 1 Product Overview

1-1

Chapter 1 Product Overview

1.1 Overview

H3C S5600 Series Ethernet Switches are high-performance, high-density,
easy-to-install, NMS-manageable intelligent Ethernet switches which support
wire-speed Layer2/3 switching.

Table 1-1 lists the models of H3C S5600 Series Ethernet Switches.

Table 1-1 Models of H3C S5600 Series Ethernet Switches

Model

Number of

10/100/1000M

electrical ports

Number of

1000M SFP

optical ports

Number of

Console ports

S5600-26C
S5600-26C-PWR

24 4

S5600-26F 4 24
S5600-50C
S5600-50C-PWR

48 4

1

Each SFP port and the corresponding 10/100/1000M Ethernet port form a Combo port.
For each Combo port, the SFP port and the 10/100/1000M Ethernet port cannot be
used at the same time. For the relationship between the Combo ports and the Ethernet
ports, refer to

Table 1-2.

Table 1-2 Combo port list

Switch model Combo Port Corresponding port

25 22
26 24
27 21

S5600-26C/S5600-26C

-PWR/S5600-26F
28 23

49 46
50 48
51 45

S5600-50C/S5600-50C

-PWR
52 47

Installation Manual
H3C S5600 Series Ethernet Switches Chapter 1 Product Overview

1-2

 Note:

z The electrical ports of S5600-26C-PWR/S5600-50C-PWR are capable of sup plying

-48 VDC power to remote PDs (powered devices, such as S2016C, S2008B,
S2016B, S2016-EI, and so on).

z The S5600-26C-PWR/S5600-50C-PWR adopts PoE power module, which provides

AC/DC power to PD devices. When delivering the AC input, the module can supply
up to 300 W power. If more power is needed, use the DC input or both AC and DC
inputs to ensure the operation of all the connected devices.

z The S5600-26C-PWR/S5600-50C-PWR can also adopt AC/DC dual input power

module. In this case, however, the two types of switches have no PoE function. And
they function exactly like the S5600-26C and S5600-50C.

1.2 S5600-26C/S5600-26C-PWR/S5600-26F Ethernet Switch

1.2.1 Front Panel

I. Front panel

The S5600-26C/S5600-26C-PWR provides 24 x 10/100/1000Base-TX Ethernet ports,
one Console port, and four 1000 Mbps SFP Combo ports on its front panel. Each SFP
port and the corresponding 10/100/1000M Ethernet port form a Combo port. For each
Combo port, the SFP port and the 10/100/1000M Ethernet port cannot be used at the
same time. For the relationship between the Combo ports and the Ethernet port s, refer
to

Table 1-2.

Figure 1-1 shows the front panel of an S5600-26C Ethernet switch.:

(1) 10/100/1000M auto-negotiation Ethernet port status LEDs
(2) 1000 Mbps SFP Combo port LED (3) Console port
(4) 7-segment digitron display (5) Power LED
(6) DC LED (7) Fabric LED
(8) Module LED (9) Port mode LED
(10) Mode button

Figure 1-1 Front panel of the S5600-26C/S5600-26C-PWR

Installation Manual
H3C S5600 Series Ethernet Switches Chapter 1 Product Overview

1-3

The S5600-26F provides 24 x 1000 Mbps SFP optical port s, one Console port, and four
1000 Mbps RJ-45 Combo ports on it s front panel. Each SFP port an d the corresponding
10/100/1000M Ethernet port form a Combo port. For each Combo port, the SFP port
and the 10/100/1000M Ethernet port cannot be used at the same time. For the
relationship between the Combo ports and the Ethernet ports, refer to

Table 1-2.

Figure 1-2. shows the front panel of an S5600-26F Ethernet switch.:

(1) SFP optical port status LED
(2) 10/100/1000M auto-negotiation Ethernet port status LEDs: left one for speed, right one for
duplex mode
(3) Console port (4) 7-segment digitron display
(5) Power LED (6) RPS LED
(7) Fabric LED (8) Module LED

Figure 1-2 Front panel of the S5600-26F

II. LEDs

The S5600-26C/S5600-26C-PWR provides one power LED, one RPS LED, one fabri c
LED, one module LED, one mode LED, one 7-segment digitron display, four pairs of
1000 Mbps SFP port status LEDs, and 24 pairs of 10/100/1000M port status LEDs on
its front panel.

The S5600-26F provides one power LED, one RPS LED, one fabric LED, one module
LED, one 7-segment digitron display , 24 pairs of 1000 Mbps SFP port status LEDs, and
four pairs of 10/100/1000M auto-negotiation Ethernet port status LEDs on its front
panel.

Table 1-3 and Table 1-4 describe respectively the LEDs on the
S5600-26C/S5600-26C-PWR and S5600-26F.

Installation Manual
H3C S5600 Series Ethernet Switches Chapter 1 Product Overview

1-4

Table 1-3 LEDs on the S5600-26C/S5600-26C-PWR

LED Mark Status Description

Speed Solid green

The port status LEDs are
showing the speed of each port.

Duplex Solid yellow

The port LEDs are showing the
duplex mode of each port.

Mode LED Mode

PoE

Blinking green
(at 1 Hz)

The port LEDs are showing the
PoE status of each port.

Solid green The switch is started normally.

Blinking green (at 1 Hz)

The system is running power-on
self-test (POST).

Solid red

The system fails the POST, or
there is another fault.

Blinking yellow (at 1 Hz)

Some ports fail the POST and
do not function.

Power
LED

PWR

OFF The switch is power-off.

Solid green

Both the AC power supply and
the DC input operate normally.

Solid yellow

The AC power supply fails or the
AC input is disconnected, while
the DC input operates normally.

DC LED RPS

OFF DC input is disconnected.

Green

The device is in the ring fabric
status; the LED blinks quickly
when the fabric port is receiving
or sending data.

Yellow

The device is in the daisy chain
fabric status; the LED blinks
quickly when the fabric port is
receiving or sending data.

Blinking green (at 3 Hz)

This device is isolated from the
whole set of fabric devices
(effective when this device is in
the fabric status).

Fabric
LED

STK

OFF

Neither of the two fabric ports is
connected.

Installation Manual
H3C S5600 Series Ethernet Switches Chapter 1 Product Overview

1-5

LED Mark Status Description

Solid green

The module is seated and
operates normally.

Blinking yellow

The module fails or is not
supported.

Module
LED

Module
(MOD)

OFF No module is installed.

POST
running

Blinking
green

The POST ID of the in-process
test is displayed:

POST failed

Blinking
red

The POST ID of the failed test
blinks.

Software
downloading

Blinking
green

A light bar rotates clockwise
around the display during the
downloading procedure.

Fan failed Solid red

An “F” is displayed.

Over
temperature
alarm

Solid red

A “t” is displayed.

Speed and
duplex
mode

Solid
green

UNIT ID in the fabric; or “1” for a
standalone unit is displayed.

7-segment
digitron
display

Unit

PoE mode

Solid
green

The utilization of the power
supply is displayed.

0 - 20%

21 - 40%

41 - 60%

61 - 80%

81 - 100%

Installation Manual
H3C S5600 Series Ethernet Switches Chapter 1 Product Overview

1-6

LED Mark Status Description

Green

The port is operating at 1000
Mbps. The LED blinks quickly
when the port is receiving or
sending data.

Yellow

The port is operating at 10/100
Mbps. The LED blinks quickly
when the port is receiving or
sending data.

Blinking
yellow
(at 3 Hz)

The port fails the POST.

Speed mode

OFF The port is not connected.

Green

The port is operating in full
duplex mode. The LED blinks
quickly when the port is
receiving or sending data.

Yellow

The port is operating in half
duplex mode. The LED blinks
quickly when the port is
receiving or sending data.

Blinking
Yellow
(3 Hz)

The port fails the POST.

Duplex
mode

OFF The port is not connected.
Solid

green

The port supplies power
normally.

Blinking
green
(at 1 Hz)

The connected device requires
more power than the maximum
power a port can supply.

The port cannot supply power
because the switch has reached
its maximum power supplied.

Solid
yellow

The port cannot supply power
because the connected device is
not a PD.

The port cannot supply power
due to the power source failure
of PoE.

Blinking
yellow (3
Hz)

The port fails the POST.

10/100/
1000M
auto­negotiation
Ethernet
port status
LED

—

PoE mode

OFF The port does not supply power.

Installation Manual
H3C S5600 Series Ethernet Switches Chapter 1 Product Overview

1-7

LED Mark Status Description

Green

The port is operating at 1000
Mbps. The LED blinks quickly
when the port is receiving or
sending data.

Blinking
yellow (3
Hz)

The port fails the POST.

Speed mode

OFF The port is not connected.

Green

The port is operating in 1000
Mbps full duplex mode. The LED
blinks quickly when the port is
receiving or sending data.

Blinking
yellow (3
Hz)

The port fails the POST.

Duplex
mode

OFF The port is not connected.

1000M
Base SFP
port mode
LED

—

PoE mode OFF

–

Table 1-4 LEDs on the S5600-26F

LED Mark Status Description

Solid green The switch is started normally.

Blinking green (at 1 Hz)

The system is running power-on
self-test (POST).

Solid red

The system fails the POST, or
there is another fault.

Blinking yellow (at 1 Hz)

Some ports fail the POST and
do not function.

Power
LED

PWR

OFF The switch is power-off.

Solid green

Both the AC power supply and
the DC input operate normally.

Solid yellow

The AC power supply fails or the
AC input is disconnected, while
the DC input operates normally.

DC LED RPS

OFF DC input is disconnected.

Installation Manual
H3C S5600 Series Ethernet Switches Chapter 1 Product Overview

1-8

LED Mark Status Description

Green

The device is in the ring fabric
status; the LED blinks quickly
when the fabric port is receiving
or sending data.

Yellow

The device is in the daisy chain
fabric status; the LED blinks
quickly when the fabric port is
receiving or sending data.

Blinking green (at 3 Hz)

This device is isolated from the
whole set of fabric devices
(effective when this device is in
the fabric status).

Fabric
LED

STK

OFF

Neither of the two fabric ports is
connected.

Solid green

The module is seated and
operates normally.

Blinking yellow

The module fails or is not
supported.

Module
LED

Module
(MOD)

OFF No module is installed.

POST
running

Blinking
green

The POST ID of the in-process
test is displayed:

POST failed

Blinking
red

The POST ID of the failed test
blinks.

Software
downloading

Blinking
green

A light bar rotates clockwise
around the display during the
downloading procedure.

Fan failed Solid red

An “F” is displayed.

Over
temperature
alarm

Solid red

A “t” is displayed.

7-segment
digitron
display

Unit

Speed and
duplex mode

Solid
green

UNIT ID in the fabric; or “1” for a
standalone unit is displayed.

Installation Manual
H3C S5600 Series Ethernet Switches Chapter 1 Product Overview

1-9

LED Mark Status Description

Green

The port is operating at 1000
Mbps. The LED blinks quickly
when the port is receiving or
sending data.

Yellow

The port is operating at 10/100
Mbps. The LED blinks quickly
when the port is receiving or
sending data.

Blinking
yellow
(at 3 Hz)

The port fails the POST.

Speed mode

OFF The port is not connected.

Green

The port is operating in full
duplex mode. The LED blinks
quickly when the port is
receiving or sending data.

Yellow

The port is operating in half
duplex mode. The LED blinks
quickly when the port is
receiving or sending data.

Blinking
Yellow
(3 Hz)

The port fails the POST.

10/100/
1000M
auto­negotiation
Ethernet
port status
LED

—

Duplex
mode

OFF The port is not connected.

Green

The port is operating at 1000
Mbps. The LED blinks quickly
when the port is receiving or
sending data.

Blinking
yellow (3
Hz)

The port fails the POST.

1000Base
SFP
optical port
status LED

—

port status
LED

OFF The port is not connected.

III. Console port

The S5600-26C/S5600-26C-PWR/S5600-26F provides an EIA/TIA-232-compliant
Console port, which enables you to configure the switch from the local or remote site.

Table 1-5 Attributes of the Console port

Item Description

Connector RJ-45
Standard EIA/TIA-232

Installation Manual
H3C S5600 Series Ethernet Switches Chapter 1 Product Overview

1-10

Item Description

Baud rate 9600 bps (default), auto-negotiation is supported

Services

Connection to an ASCII terminal
Connection to the serial port of a local terminal (a PC for

example) or a remote terminal (through a pair of modems)
running terminal emulation software

1.2.2 Rear Panel

I. Rear panel

 Note:

The ports of the AC/DC dual input power module and the PoE power module are
exactly the same, so only one rear panel illustration is shown below.

The S5600-26C/S5600-26C-PWR/S5600-26F provides two sockets for pluggable
power module, two fabric ports, one expansion slot, and one grounding screw on its
rear panel, as shown in the following figure.

(1) AC-input power socket for the power module (2) Expansion module
(3) Grounding screw (4) Fabric ports
(5) Fabric port LEDs (6) RPS LED
(7) DC-input power socket for the power module

Figure 1-3 Rear panel of the S5600-26C/S5600-26C-PWR/S5600-26F

II. Fabric port

The fabric port marked with “UP” connects to a port of the same type on an upstream
device; the fabric port marked with “DOWN” connects to a port of the same type on a
downstream device.

Installation Manual
H3C S5600 Series Ethernet Switches Chapter 1 Product Overview

1-11

Table 1-6 Fabric port LEDs

LED Mark Status Indicate

Solid green The fabric port is properly connected.
Blinking

green

The fabric port is properly connected and
the port is receiving or sending data.

Fabric
port LED

UP(DOWN)

OFF The fabric port is disconnected.

1.3 S5600-50C/S5600-50C-PWR Ethernet Switch

1.3.1 Front Panel

I. Front panel

The S5600-50C/S5600-50C-PWR provides 48 x 10/100/1000Base-TX Ethernet ports,
one Console port, and four 1000 Mbps SFP Combo ports on its front panel. Each SFP
port and the corresponding 10/100/1000M Ethernet port form a Combo port. For each
Combo port, the SFP port and the 10/100/1000M Ethernet port cannot be used at the
same time. For the relationship between the Combo ports and the Ethernet port s, refer
to

Table 1-2.

Figure 1-4 shows the front panel of an S5600-50C/S5600-50C-PWR Ethernet switch:

(1) 10/100/1000M auto-negotiation Ethernet port status LEDs
(2) Console Port
(3) 7-segment digitron display (4) Mode button
(5) Mode LED (6) Power LED
(7) RPS LED (8) Fabric LED
(9) Module LED (10) 1000 Mbps SFP combo port LED

Figure 1-4 Front panel of the S5600-50C/S5600-50C-PWR

Installation Manual
H3C S5600 Series Ethernet Switches Chapter 1 Product Overview

1-12

II. LEDs

The S5600-50C/S5600-50C-PWR provides one power LED, RPS LED, fabric LED,
module LED, mode LED, 7-segment digitron display, 1000 Mbps SFP port statu s LED,
and auto-negotiation Ethernet port status LED on its front panel. The meaning of each
LED is shown in

Table 1-3

III. Console port

The S5600-50C/S5600-50C-PWR provides an EIA/TIA-232-compliant console port,
which enables you to configure the switch from the local or remote site. For the
attributes of the port, refer to

Table 1-5.

1.3.2 Rear panel

I. Rear panel

 Note:

The ports of the AC/DC dual input power module and the PoE power module are
exactly the same, so only one rear panel illustration is shown below.

The S5600-50C/S5600-50C-PWR provides two sockets for pluggable power module,
two fabric ports, one expansion slot, and one grounding screw on its rear panel, as
shown in the following figure.

(1) AC-input power socket for the power module (2) Expansion module
(3) Grounding screw (4) Fabric ports
(5) Fabric port LEDs (6) RPS LED
(7) DC-input power socket for the power module

Figure 1-5 Rear panel of the S5600-50C/S5600-50C-PWR

II. Fabric ports

For fabric ports and the meanings of their LEDs, refer to Table 1-6.

Installation Manual
H3C S5600 Series Ethernet Switches Chapter 1 Product Overview

1-13

1.4 Power system

z AC power input range

Rated voltage: 100 to 240 VAC; 50/60 Hz
Max. voltage range: 90 to 264 VAC; 50/60 Hz

z DC power input range

Rated voltage: –48 to–60 V
Max. voltage range: –36 to–72 V

z AC input of the PoE power module

Rated voltage: 100 to 240 VAC; 50/60 Hz
Max. voltage range: 90 to 264 VAC; 50/60 Hz

z DC input of the PoE power module

Rated voltage: –53.5 V
Max. voltage range: –52 to –55 V

 Note:

The S5600-26C-PWR/S5600-50C-PWR must use the external PoE PSU
recommended by H3C as its DC input, but not the -48VDC power supply generally
available in the equipment room. Otherwise, the device may be damaged.

1.5 Cooling system

S3100-8TP-PWR-EI Ethernet switches each run two fans for heat dissipation.
Table 1-7 S5600 Ethernet switches cooling system

(1)

Model S5600-26C S5600-26C-PWR S5600-26F

Cooling system

Two fans are for the
device and two are
for the power supply
module.

Two fans are for
the device and four
are for the power
supply module.

Four fans are for
the device and two
are for the power
supply module.

Installation Manual
H3C S5600 Series Ethernet Switches Chapter 1 Product Overview

1-14

Table 1-8 S5600 Ethernet switches cooling system (2)

Model S5600-50C S5600-26C-PWR

Cooling system

Two fans are for the device
and two are for the power
supply module.

Two fans are for the device and
four are for the power supply
module.

1.6 Attributes of 1000 Mbps SFP port

The S5600-26C/S5600-26C-PWR/S5600-50C/S5600-50C-PWR provides 4 × 1000
Mbps SFP ports on it s front panel. The S5600 -26F provides 24 × 1000 Mbp s SFP ports
on its front panel.

SFP modules allow for great flexibility in networking because they are hot swappable
and user configurable.

Table 1-9 lists the available SFP modules that you can select as re quired:

Table 1-9 Optical port module

Type Model

SFP-GE-SX-MM850-A
SFP-GE-LX-SM1310-A
SFP-GE-LH40-SM1310
SFP-GE-LH40-SM1550

1000M SFP module

SFP-GE-LH70-SM1550

SFP
module

SFP electrical interface module SFP-GE-T

 Note:

z Only the optical module that H3C Technology provides or recommends can be

used.

z The types of SFP modules may vary with time. Consult H3C marketing personnel or

technical support personnel to obtain the latest information about SFP modules.

z For specifications of SFP modules, refer to H3C Low End Series Ethernet Switches

Pluggable Module Manual.

Installation Manual
H3C S5600 Series Ethernet Switches Chapter 1 Product Overview

1-15

1.7 Expansion Module

The S5600 Series Ethernet switches provide one expansion module slot on the rear
panel. The expansion mode that can be used in this slot includes 8-port 1000 Mbps
SFP module, 1-port 10 Gbps XENPAK module, and 2-port 10 Gbps XFP module.

I. 8-port 1000 Mbps SFP module

(1) Port status LEDs (2) SFP ports (3) Module power LED

Figure 1-6 8-port 1000 Mbps SFP module

This module provides eight 1000 Mbps SFP external optical/electrical ports.

z For an optical port, you can choose one of the following SFP modules according to

your needs.

Table 1-10 Optical port module supported by 8-port 1000 Mbps SFP module

SFP module

Central wavelength

Fiber specifications

Maximum transmission distance

SFP-GE-SX-MM850-A
SFP-GE-LX-SM1310-A

SFP module 1000M SFP module

SFP-GE-LH40-SM1310

 Note:

z The types of SFP modules may vary with time. Consult H3C marketing personnel or

technical support personnel to obtain the latest information about SFP modules.

z For specifications of SFP modules, refer to H3C Low End Series Ethernet Switches

Pluggable Module Manual.

z For an RJ-45 electrical port with the transmission distance is 100 m (328 ft), you

can select the RJ-45 connector as shown in the following figure, and the
category-5 twisted pair as the data transmission medium.

Installation Manual
H3C S5600 Series Ethernet Switches Chapter 1 Product Overview

1-16

Figure 1-7 RJ-45 connector

Table 1-11 Pinouts of the RJ-45 GE port

1000Base-TX

Pin

Signal Function

1 MX_0+ Data transmit/receive
2 MX_0- Data transmit/receive
3 MX_1+ Data transmit/receive
4 MX_2+ Data transmit/receive
5 MX_2- Data transmit/receive
6 MX_1- Data transmit/receive
7 MX_3+ Data transmit/receive
8 MX_3- Data transmit/receive

II. 2-port 10 Gbps XFP module

(1) Module power LED (2) Port status LEDs (3) 10 Gbps XFP optical ports

Figure 1-8 2-port 10 Gbps XFP module

This module provide two 10 Gbps XFP optical port. The following table lists the
available XFP optical modules that you can select according to your needs: