H3C S5500-28F-EI-DC, S5500-28C-EI-DC, S5500-28C-EI, S5500-28F-EI, S5500-52C-PWR-EI User Manual
...
H3C S5500-EI Series Ethernet Switches
Installation Manual
Hangzhou H3C Technologies Co., Ltd.
http://www.h3c.com
Manual Version: 20071215-C-1.01
Copyright © 2007, Hangzhou H3C Technologies Co., Ltd. and its licensors
All Rights Reserved
No part of this manual may be reproduced or transmitted in any form or by any means
without prior written consent of Hangzhou H3C Technologies Co., Ltd.
Trademarks
H3C, , Aolynk, , H3Care,
Neocean, NeoVTL, SecPro, SecPoint, SecEngine, SecPath, Comware, Secware,
Storware, NQA, VVG, V
HUASAN are trademarks of Hangzhou H3C Technologies Co., Ltd.
All other trademarks that may be mentioned in this manual are the property of their
respective owners.
Notice
The information in this document is subject to change without notice. Every effort has
been made in the preparation of this document to ensure accuracy of the contents, but
all statements, information, and recommendations in this document do not constitute
the warranty of any kind, express or implied.
To obtain the latest information, please access:
http://www. h3c.com
Technical Support
customer_service@h3c.com
http://www. h3c.com
, TOP G, , IRF, NetPilot,
2
G, VnG, PSPT, XGbus, N-Bus, TiGem, InnoVision and
About This Manual
Related Documentation
In addition to this manual, each H3C S5500-EI Series Ethernet Switches
documentation set includes the following:
Manual Description
Organization
H3C S5500-EI Series Ethernet Switches Installation Manual is organized as follows:
H3C S5500-EI Series Ethernet Switches
Operation Manual
H3C S5500-EI Series Ethernet Switches
Command Manual
Chapter Contents
1 Product Overview
2 Installation Preparations
3 Installation
4 Initial Power-On
Introduces the characteristics and technical
specifications of S5500-EI Series Ethernet Switches.
Introduces the installation preparation and precaution
of S5500-EI Series Ethernet Switches.
Introduces the procedures to install an S5500-EI
Series Ethernet Switch, including the setup of the
mainframe, cards and cables.
Introduces the booting process of an S5500-EI Series
Ethernet Switch, including the power-on booting of the
switch and the system initialization.
It is used for assisting the users in data
configurations and typical applications.
It is used for assisting the users in using
various commands.
5 Boot ROM and Host
Software Loading
6 Maintenance and
Troubleshooting
Appendix A Lightning
Protection of the Switch
Introduces how to load Boot OM and host software for
an S5500-EI Series Ethernet Switch.
Introduces the problems that might occur during the
installation and the booting of an S5500-EI Series
Ethernet Switch and the related solution.
Introduces lightning protection of S5500-EI Series
Ethernet Switches.
Conventions
The manual uses the following conventions:
I. GUI conventions
Convention Description
< >
[ ]
/
Button names are inside angle brackets. For example, click
<OK>.
Window names, menu items, data table and field names
are inside square brackets. For example, pop up the [New
User] window.
Multi-level menus are separated by forward slashes. For
example, [File/Create/Folder].
II. Symbols
Convention Description
Means reader be extremely careful. Improper operation
Warning
Caution
Note Means a complementary description.
may cause bodily injury.
Means reader be careful. Improper operation may cause
data loss or damage to equipment.
Environmental Protection
This product has been designed to comply with the requirements on environmental
protection. For the proper storage, use and disposal of this product, national laws and
regulations must be observed.
Installation Manual
H3C S5500-EI Series Ethernet Switches Table of Contents
Table of Contents
Chapter 1 Product Overview........................................................................................................1-1
1.1 Introduction........................................................................................................................1-1
1.2 S5500-28C-EI....................................................................................................................1-2
1.2.1 Appearance.............................................................................................................1-2
1.2.2 Front Panel.............................................................................................................. 1-3
1.2.3 Rear Panel .............................................................................................................. 1-3
1.2.4 Power Supply System.............................................................................................1-3
1.2.5 Cooling System.......................................................................................................1-4
1.2.6 LEDs........................................................................................................................ 1-4
1.3 S5500-28C-EI-DC.............................................................................................................. 1-7
1.3.1 Appearance.............................................................................................................1-7
1.3.2 Front Panel.............................................................................................................. 1-8
1.3.3 Rear Panel .............................................................................................................. 1-8
1.3.4 Power System.........................................................................................................1-8
1.3.5 Cooling System.......................................................................................................1-9
1.3.6 LEDs........................................................................................................................ 1-9
1.4 S5500-52C-EI..................................................................................................................1-12
1.4.1 Appearance...........................................................................................................1-12
1.4.2 Front Panel............................................................................................................ 1-13
1.4.3 Rear Panel ............................................................................................................ 1-13
1.4.4 Power Supply System...........................................................................................1-13
1.4.5 Cooling System.....................................................................................................1-14
1.4.6 LEDs......................................................................................................................1-14
1.5 S5500-28C-PWR-EI ........................................................................................................1-14
1.5.1 Appearance...........................................................................................................1-14
1.5.2 Front Panel............................................................................................................ 1-14
1.5.3 Rear Panel ............................................................................................................ 1-15
1.5.4 Power Supply System...........................................................................................1-15
1.5.5 Cooling System.....................................................................................................1-15
1.5.6 LEDs......................................................................................................................1-15
1.6 S5500-52C-PWR-EI ........................................................................................................1-19
1.6.1 Appearance...........................................................................................................1-19
1.6.2 Front Panel............................................................................................................ 1-20
1.6.3 Rear Panel ............................................................................................................ 1-20
1.6.4 Power Supply System...........................................................................................1-21
1.6.5 Cooling System.....................................................................................................1-21
1.6.6 LEDs......................................................................................................................1-21
1.7 S5500-28F-EI...................................................................................................................1-21
i
Installation Manual
H3C S5500-EI Series Ethernet Switches Table of Contents
1.7.1 Appearance...........................................................................................................1-21
1.7.2 Front Panel............................................................................................................ 1-22
1.7.3 Rear Panel ............................................................................................................ 1-22
1.7.4 Power System.......................................................................................................1-22
1.7.5 Cooling System.....................................................................................................1-23
1.7.6 LEDs......................................................................................................................1-23
1.8 System Specifications of the S5500-EI Series................................................................1-26
1.9 Pluggable Modules .......................................................................................................... 1-28
1.10 Optional Interface Modules............................................................................................1-29
1.10.1 Description of LEDs on Extended Modules ........................................................ 1-30
1.11 CX4 Cable......................................................................................................................1-30
Chapter 2 Installation Preparations............................................................................................. 2-1
2.1 Safety Precautions............................................................................................................. 2-1
2.2 Installation Site...................................................................................................................2-1
2.2.1 Temperature/Humidity.............................................................................................2-1
2.2.2 Cleanness ............................................................................................................... 2-2
2.2.3 Electromagnetic Susceptibility ................................................................................ 2-2
2.2.4 Laser Safety............................................................................................................2-3
2.3 Installation Tools................................................................................................................ 2-3
Chapter 3 Installation....................................................................................................................3-1
3.1 Installing the Switch into a 19-Inch Cabinet....................................................................... 3-1
3.1.1 Introduction to Mounting Ears.................................................................................3-2
3.1.2 Introduction to Guide Rails......................................................................................3-3
3.1.3 Using Front Mounting Ears to Install the Switch.....................................................3-4
3.1.4 Using Front Mounting Ears and a Tray...................................................................3-5
3.1.5 Using Front and Rear Mounting Ears .....................................................................3-5
3.1.6 Using Front Mounting Ears and Guide Rails........................................................... 3-8
3.2 Mounting the Switch on a Workbench.............................................................................3-10
3.3 Connecting the Power Cables and the Grounding Cable................................................ 3-11
3.3.1 Connecting the AC Power Cable .......................................................................... 3-11
3.3.2 Connecting the DC Power Cable..........................................................................3-12
3.3.3 Connecting the Grounding Cable.......................................................................... 3-17
3.4 Connecting the Console Cable........................................................................................ 3-19
3.4.1 Console Cable....................................................................................................... 3-19
3.4.2 Connection Procedure ..........................................................................................3-20
3.5 Installing and Removing Optional Interface Modules......................................................3-20
3.5.1 10 GE XFP Interface Module................................................................................3-21
3.5.2 Short-haul Dual-port 10 GE CX4 Interface Module...............................................3-23
3.6 Installing and Removing the Dedicated CX4 Cable.........................................................3-24
3.6.1 Installing the Dedicated CX4 Cable......................................................................3-24
3.6.2 Removing the Dedicated CX4 Cable....................................................................3-24
3.7 Verifying the Installation................................................................................................... 3-24
ii
Installation Manual
H3C S5500-EI Series Ethernet Switches Table of Contents
Chapter 4 Initial Power-On ...........................................................................................................4-1
4.1 Setting Up the Configuration Environment........................................................................4-1
4.2 Connecting the Console Cable.......................................................................................... 4-1
4.3 Setting Terminal Parameters............................................................................................. 4-1
4.4 Booting the Switch.............................................................................................................4-5
4.4.1 Checking before Power-On.....................................................................................4-5
4.4.2 Powering On the Switch..........................................................................................4-5
4.4.3 Changing the Boot Mode ........................................................................................ 4-8
Chapter 5 Boot ROM and Host Software Loading ..................................................................... 5-1
5.1 Introduction to Loading Modes .......................................................................................... 5-1
5.2 Local Software Loading.....................................................................................................5-1
5.2.1 Boot Menu...............................................................................................................5-2
5.2.2 Loading Software Using XModem Through the Console Port................................ 5-3
5.2.3 Loading Software Using TFTP through an Ethernet Port.......................................5-9
5.2.4 Loading Software Using FTP Through Ethernet Port........................................... 5-11
5.3 Remote Software Loading...............................................................................................5-12
5.3.1 Remote Loading Using FTP..................................................................................5-12
5.3.2 Remote Loading Using TFTP................................................................................5-14
Chapter 6 Maintenance and Troubleshooting............................................................................ 6-1
6.1 Software Loading Failure...................................................................................................6-1
6.2 Password Loss...................................................................................................................6-1
6.2.1 User Password Loss............................................................................................... 6-1
6.2.2 BootROM Password Loss....................................................................................... 6-2
6.3 Power Supply Failure......................................................................................................... 6-2
6.4 Configuration System Failure ............................................................................................ 6-2
iii
Installation Manual
H3C S5500-EI Series Ethernet Switches Chapter 1 Product Overview
Chapter 1 Product Overview
1.1 Introduction
H3C S5500-EI Series Ethernet Switches (hereinafter referred to as the S5500-EI series)
are Gigabit Ethernet switching products developed by Hangzhou H3C Technologies
Co., Ltd. (hereinafter referred to as H3C). The S5500-EI series support diversified
service features, IPv6 forwarding, and routing function, and provide 10GE extended
module slots. Through the H3C proprietary cluster management, you can streamline
network management. The S5500-EI series are designed to operate at the
convergence or access layer of enterprise networks and metropolitan area networks
(MANs). The S5500-EI series support the IPv4/IPv6 dual stack and can also be used
for connecting server groups in data centers.
Table 1-1 lists the models of the S5500-EI series.
Table 1-1 Models of the S5500-EI series
Number of
Model
S5500-28C-EI 24 4
S5500-28C-EI-DC 24 4
S5500-52C-EI 48 4
S5500-28C-PWR-EI 24 4
S5500-52C-PWR-EI 48 4
S5500-28F-EI 8 24
Together with an auto-sensing 10/100/1000BASE-T Ethernet port, each 1000Base-X
SFP port forms a Combo port. For each Combo port, either the SFP port or the
auto-sensing 10/100/1000BASE-T Ethernet port can be used at a time. For the
mapping between the two ports forming a Combo port, refer to
Table 1-2 Mapping between two ports forming a Combo port
auto-sensing
10/100/1000Base-T
Ethernet ports
Number of
1000Base-X SFP
ports
Table 1-2.
Number
of
console
ports
1
Model
S5500-28C-EI
S5500-28C-EI-DC
S5500-28C-PWR-EI
1000Base-X SFP
port number
25 22
26 24
27 21
1-1
Auto-sensing 10/100/1000Base-T
Ethernet port number
Installation Manual
H3C S5500-EI Series Ethernet Switches Chapter 1 Product Overview
Model
1000Base-X SFP
port number
28 23
49 46
Auto-sensing 10/100/1000Base-T
Ethernet port number
S5500-52C-EI
S5500-52C-PWR-EI
S5500-28F-EI
For the convenience of monitoring the running of the S5500-EI series, LEDs are also
equipped on their front panel.
1.2 S5500-28C-EI
50 48
51 45
52 47
25 17
26 18
27 19
28 20
29 21
30 22
31 23
32 24
1.2.1 Appearance
The S5500-28C-EI provides twenty-four auto-sensing 10/100/1000BASE-T Ethernet
ports, four 1000Base-X SFP port s, and one console port on the front pan el, and one AC
power socket, one redundant power system (RPS) port, and two extended module slots
on the rear panel.
Figure 1-1 Appearance of the S5500-28C-EI
Figure 1-2 shows the appearance of the S5500-28C-EI.
1-2
Installation Manual
H3C S5500-EI Series Ethernet Switches Chapter 1 Product Overview
1.2.2 Front Panel
(2) (3) (4) (5) (6) (7) (8)
(1)
(1)
(1) Auto-sensing 10/100/1000Base-T Ethernet port status LEDs
(2) SFP port status LEDs
(3) Console port (4) 7-segment digital LED
(5) Power LED (6) RPS LED
(7) LED for extended module slot 1 (8) LED for extended module slot 2
(9) Mode LED (10) Mode button
Figure 1-2 Front panel of the S5500-28C-EI
(2) (3) (4) (5) (6) (7) (8)
(9)
(10)
(10)
(9)
1.2.3 Rear Panel
(1) (2)
(1) (2)
(1) AC power socket (2) RPS port
(3) Grounding screw (4) Extended module slot 1
(5) Extended module slot 2
Figure 1-3 Rear panel of the S5500-28C-EI
1.2.4 Power Supply System
The S5500-28C-EI can adopt AC input, or 12 V RPS input, or both to provide backup.
Only the recommended RPS can be used.
z AC power input
Rated voltage range: 100 VAC to 240 VAC, 50 Hz or 60 Hz
(3)
(3)
(4)
(4)
(5)
(5)
Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz
z RPS input
Rated voltage range: 10.8 VDC to 13.2 VDC
1-3
Installation Manual
H3C S5500-EI Series Ethernet Switches Chapter 1 Product Overview
1.2.5 Cooling System
The S5500-28C-EI is equipped with four fans for heat dissipation.
1.2.6 LEDs
For descriptions about LEDs, see Table 1-3. You can switch the Mode LED display
mode between speed and duplex by pressing the Mode button on the panel.
Table 1-3 LEDs on the front panel of the S5500-28C-EI
LED Mark Status Description
Mode LED Mode
Power LED PWR
Redundant power
system LED
RPS
Speed Solid green Rate of the port
Duplex Solid yellow Duplex mode of the port
Solid green
The switch is started
normally.
The system is running a
Flashing green (1 Hz)
power-on self-test
(POST).
The system fails the
Solid red
POST or a power failure
occurs.
Flashing yellow (1 Hz)
OFF
Some ports fail a POST
or a port failure occurs.
The power is
disconnected.
The AC power supply is
Solid green
normal and the RPS is
connected and works
normally.
The RPS input is
Solid yellow
normal, but an AC input
failure occurs or no AC
power is connected.
Module LED MOD
OFF No RPS is connected.
The module is in
Solid green
position and works
normally.
The switch does not
Flashing yellow
support the module or a
module failure occurs.
OFF No module is installed.
1-4
Installation Manual
H3C S5500-EI Series Ethernet Switches Chapter 1 Product Overview
LED Mark Status Description
7-segment digital
LED
Unit
POST
running
POST
failed
Software
loading
Fan
failure
Over-tem
perature
alarm
The power
LED flashes
green
The power
LED flashes
red
The power
LED flashes
green.
The power
LED is solid
red.
The power
LED is solid
red.
The LED displays the
POST test ID.
The LED flashes the
POST test ID of the
failed test.
A bar rotates clockwise
around the LED.
The LED displays F.
The LED displays t.
Cluster
state
The power
LED is solid
green.
For a command switch,
the LED displays C.
For a member switch,
the LED displays S.
For a candidate switch,
the LED displays c.
The LED displays 1 if
there is only one unit.
1-5
Installation Manual
H3C S5500-EI Series Ethernet Switches Chapter 1 Product Overview
LED Mark Status Description
A 1000 Mbps link is
present. When data is
Green
being received or sent,
the LED flashes at a
high frequency.
A 10/100 Mbps link is
Speed
Yellow
present. When data is
being received or sent,
the LED flashes at a
high frequency.
10/100/1000Base
-T port status LED
SFP port status
LED (1000 Mbps)
—
—
Duplex
The
Mode
button
has no
effect on
the LED.
Flashing
yellow (3 Hz)
The port fails the POST.
OFF No link is present.
The port works in the full
duplex mode. The LED
Green
flashes at a high
frequency when data is
being received or sent.
The port works in the
half duplex mode. The
Yellow
LED flashes at a high
frequency when data is
being received or sent
Flashing
yellow (3 Hz)
The port fails the POST.
OFF No link is present.
A 1000 Mbps link is
present. When data is
Green
being received or sent,
the LED flashes at a
high frequency.
Flashing
yellow (3 Hz)
The port fails the POST.
1-6
OFF No link is present.
Installation Manual
H3C S5500-EI Series Ethernet Switches Chapter 1 Product Overview
LED Mark Status Description
A 100 Mbps link is
present. When data is
Yellow
Speed
being received or sent,
the LED flashes at a
high frequency.
SFP port status
LED (100 Mbps)
1.3 S5500-28C-EI-DC
1.3.1 Appearance
The S5500-28C-EI-DC provides twenty-four auto-sensing 10/100/1000BASE-T
Ethernet ports, four 1000Base-X SFP ports, and one console port on the front panel,
and one –48 VDC power socket, one RPS port, and two extended module slots on the
rear panel.
Figure 1-4 shows the appearance of the S5500-28C-EI-DC.
—
Duplex
Flashing
yellow (3 Hz)
OFF No link is present.
Green
Flashing
yellow (3 Hz)
OFF No link is present.
The port failed the
POST.
The port operates in the
full duplex mode. When
data is being received or
sent, the LED flashes at
a high frequency.
The port fails the POST.
Figure 1-4 Appearance of the S5500-28C-EI-DC
1-7
Installation Manual
H3C S5500-EI Series Ethernet Switches Chapter 1 Product Overview
1.3.2 Front Panel
(2) (3) (4) (5) (6) (7) (8)
(1)
(1)
(1) Auto-sensing 10/100/1000Base-T Ethernet port status LEDs
(2) SFP port status LEDs
(3) Console port (4) 7-segment digital LED
(5) Power LED (6) RPS LED
(7) LED for extended module slot 1 (8) LED for extended module slot 2
(9) Mode LED (10) Mode button
Figure 1-5 Front panel of the S5500-28C-EI-DC
(2) (3) (4) (5) (6) (7) (8)
(9)
(10)
(10)
(9)
1.3.3 Rear Panel
(1) –48 VDC power socket (2) RPS port
(3) Grounding screw (4) Extended module slot 1
(5) Extended module slot 2
Figure 1-6 Rear panel of the S5500-28C-EI-DC
1.3.4 Power System
The S5500-28C-EI-DC can adopt DC input, or 12V RPS input, or both to provide
backup. Only the recommended RPS can be used.
z –48 VDC power input
Rated voltage range: –48 VDC to –60 VDC
(1) (2) (3) (4) (5)(1) (2) (3) (4) (5)
Input voltage range: –36 VDC to –72 VDC
z RPS input
Rated voltage range: 10.8 VDC to 13.2 VDC
1-8
Installation Manual
H3C S5500-EI Series Ethernet Switches Chapter 1 Product Overview
1.3.5 Cooling System
The S5500-28C-EI-DC is equipped with four fans for heat dissipation.
1.3.6 LEDs
For descriptions about LEDs, see Table 1-4. You can switch the Mode LED display
mode between speed and duplex by pressing the Mode button on the p anel.
Table 1-4 LEDs on the front panel of the S5500-28C-EI-DC
LED Mark Status Description
Mode LED Mode
Power LED PWR
Redundant power
system LED
RPS
Speed Solid green Rate of the port
Duplex Solid yellow Duplex mode of the port
Solid green
The switch is started
normally.
The system is running a
Flashing green (1 Hz)
power-on self-test
(POST).
The system fails the
Solid red
POST or a power failure
occurs.
Flashing yellow (1 Hz)
OFF
Some ports fail a POST
or a port failure occurs.
The power is
disconnected.
The DC input is normal
Solid green
and the RPS is
connected and works
normally.
The RPS input is
Solid yellow
normal, but a DC input
failure occurs or no DC
power is connected.
Module LED MOD
OFF No RPS is connected.
The module is in
Solid green
position and works
normally.
The switch does not
Flashing yellow
support the module or a
module failure occurs.
OFF No module is installed.
1-9
Installation Manual
H3C S5500-EI Series Ethernet Switches Chapter 1 Product Overview
LED Mark Status Description
7-segment digital
LED
Unit
POST
running
POST
failed
Software
loading
Fan
failure
Over-tem
perature
alarm
The power
LED flashes
green
The power
LED flashes
red
The power
LED flashes
green.
The power
LED is solid
red.
The power
LED is solid
red.
The LED displays the
POST test ID.
The LED flashes the
POST test ID of the
failed test.
A bar rotates clockwise
around the LED.
The LED displays F.
The LED displays t.
Cluster
state
The power
LED is solid
green.
For a command switch,
the LED displays C.
For a member switch,
the LED displays S.
For a candidate switch,
the LED displays c.
The LED displays 1 if
there is only one unit.
1-10
Installation Manual
H3C S5500-EI Series Ethernet Switches Chapter 1 Product Overview
LED Mark Status Description
A 1000 Mbps link is
present. When data is
Green
being received or sent,
the LED flashes at a
high frequency.
A 10/100 Mbps link is
Speed
Yellow
present. When data is
being received or sent,
the LED flashes at a
high frequency.
10/100/1000Base
-T port status LED
SFP port status
LED (1000 Mbps)
—
—
Duplex
The
Mode
button
has no
effect on
the LED.
Flashing
yellow (3 Hz)
The port fails the POST.
OFF No link is present.
The port works in the full
duplex mode. The LED
Green
flashes at a high
frequency when data is
being received or sent.
The port works in the
half duplex mode. The
Yellow
LED flashes at a high
frequency when data is
being received or sent
Flashing
yellow (3 Hz)
The port fails the POST.
OFF No link is present.
A 1000 Mbps link is
present. When data is
Green
being received or sent,
the LED flashes at a
high frequency.
Flashing
yellow (3 Hz)
The port fails the POST.
1-11
OFF No link is present.
Installation Manual
H3C S5500-EI Series Ethernet Switches Chapter 1 Product Overview
LED Mark Status Description
A 100 Mbps link is
present. When data is
Yellow
Speed
being received or sent,
the LED flashes at a
high frequency.
SFP port status
LED (100 Mbps)
1.4 S5500-52C-EI
1.4.1 Appearance
The S5500-52C-EI provides forty-eight auto-sensing 10/100/1000BASE-T Ethernet
ports, four 1000Base-X SFP port s, and one console port on the front pan el, and one AC
power socket, one RPS port, and two extended module slots on the rear panel.
1-8 shows the appearance of the S5500-52C-EI.
—
Duplex
Flashing
yellow (3 Hz)
OFF No link is present.
Green
Flashing
yellow (3 Hz)
OFF No link is present.
The port failed the
POST.
The port operates in the
full duplex mode. When
data is being received or
sent, the LED flashes at
a high frequency.
The port fails the POST.
Figure
Figure 1-7 Appearance of the S5500-52C-EI
1-12
Installation Manual
H3C S5500-EI Series Ethernet Switches Chapter 1 Product Overview
1.4.2 Front Panel
(1) Auto-sensing 10/100/1000Base-T Ethernet port status LEDs
(2) Console port (3) 7-segment digital LED
(4) Mode button (5) Mode LED
(6) Power LED (7) RPS LED
(8) LED for extended module slot 1 (9) LED for extended module slot 2
(10) SFP port status LED
Figure 1-8 Front panel of the S5500-52C-EI
1.4.3 Rear Panel
(1)
(1)
(1) (2)
(10 )
(10 )
(2)
(2)
(3) (6)
(3) (6)
(3)
(3)
(4) (5) (1) (2)
(4) (5)
(4)
(4)
(5)
(5)
(7)
(7)
(8)
(8)
(9)
(9)
(1) AC power socket (2) RPS port
(3) Grounding screw (4) Extended module slot 1
(5) Extended module slot 2
Figure 1-9 Rear panel of the S5500-52C-EI
1.4.4 Power Supply System
The S5500-52C-EI can adopt AC input, or 12V RPS input, or both to provide backup.
Only the recommended RPS can be used.
z AC power input
Rated voltage range: 100 VAC to 240 VAC, 50 Hz or 60 Hz
Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz
z RPS input
Rated voltage range: 10.8 VDC to 13.2 VDC
1-13
Installation Manual
H3C S5500-EI Series Ethernet Switches Chapter 1 Product Overview
1.4.5 Cooling System
The S5500-52C-EI is equipped with four fans for heat dissipation.
1.4.6 LEDs
The LEDs on the front panel of the S5500-52C-EI are the same as those of the
S5500-28C-EI. For details, see
Table 1-3.
1.5 S5500-28C-PWR-EI
1.5.1 Appearance
The S5500-28C-PWR-EI provides twenty-four auto-sensing 10/100/1000Base-T
Ethernet ports, four 1000Base-X SFP ports, one console port on the front panel, and
one AC power socket, one RPS port, and two extended module slots on the rear p anel.
Figure 1-10 shows the appearance of the S5500-28C-PWR-EI.
Figure 1-10 Appearance of the S5500-28C-PWR-EI
1.5.2 Front Panel
(1) Auto-sensing 10/100/1000Base-T Ethernet port status LEDs
(2) SFP port status LED
(3) Console port (4) 7-segment digital LED
(5) Power LED (6) RPS LED
(7) LED for extended module slot 1 (8) LED for extended module slot 2
(9) Mode LED (10) Mode button
(1)
(1)
(1)
(1)
(2) (3) (4) (5) (6) (7) (8)
(2) (3) (4) (5) (6) (7) (8)
(2) (3) (4) (5) (6) (7) (8)
(2) (3) (4) (5) (6) (7) (8)
(9)
(9)
(9)
(10)
(10)
(10)
(10)
(9)
Figure 1-11 Front panel of the S5500-28C-PWR-EI
1-14
Installation Manual
H3C S5500-EI Series Ethernet Switches Chapter 1 Product Overview
1.5.3 Rear Panel
(1) (2)
(1) (2)
(3)
(3)
(4)
(4)
(5)
(5)
(1) RPS port (2) AC power socket
(3) Grounding screw (4) Extended interface module slot 1
(5) Extended module slot 2
Figure 1-12 Rear panel of the S5500-28C-PWR-EI
1.5.4 Power Supply System
The S5500-28C-PWR-EI can adopt AC power input, or DC power input, or both to
provide backup.
z AC power input
Rated voltage range: 100 VAC to 240 VAC, 50 Hz or 60 Hz
Rated voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz
Only the RPS recommended by H3C can be used for the S5500-28C-PWR-EI. The –48
VDC power supply in the equipment room cannot be used directly. Otherwise, the
device may be damaged.
z DC power input
Rated voltage range: –52 VDC to –55 VDC
1.5.5 Cooling System
The S5500-28C-PWR-EI is equipped with six fans for heat dissipation.
1.5.6 LEDs
For descriptions about LEDs, see Table 1-5. You can switch the Mode LED display
mode between speed, duplex, and PoE by pressing the Mode button on the panel.
Table 1-5 Descriptions of the LEDs on the front panel of S5500-28C-PWR-EI
LED Mark Status Description
Mode LED Mode
Speed Solid green Rate of the port
Duplex Solid yellow Duplex mode of the port
PoE
1-15
Flashing
green (1 Hz)
PoE mode of the port
Installation Manual
H3C S5500-EI Series Ethernet Switches Chapter 1 Product Overview
LED Mark Status Description
Power LED PWR
Redundant power
system LED
RPS
Solid green
Flashing green (1 Hz)
Solid red
Flashing yellow (1 Hz)
OFF
Solid green
Solid yellow
OFF
The switch is started
normally.
The system is running a
power-on self-test
(POST).
The system fails the
POST or a power failure
occurs.
Some ports fail a POST
or a port failure occurs.
The power is
disconnected.
The AC power input and
the DC power input are
both normal.
The DC power input is
normal, but an AC
power failure occurs or
no AC power is
connected.
No DC power is
connected.
Module LED MOD
The module is in
Solid green
position and works
normally.
The switch does not
Flashing yellow
support the module or a
module failure occurs.
OFF No module is installed.
1-16
Installation Manual
H3C S5500-EI Series Ethernet Switches Chapter 1 Product Overview
LED Mark Status Description
7-segment digital
LED
Unit
POST
running
POST
failed
Software
loading
Fan
failure
Over-tem
perature
alarm
The power
LED flashes
green
The power
LED flashes
red
The power
LED flashes
green.
The power
LED is solid
red.
The power
LED is solid
red.
The LED displays the
POST test ID.
The LED flashes the
POST test ID of the
failed test.
A bar rotates clockwise
around the LED.
The LED displays F.
The LED displays t.
Cluster
state
PoE
mode
The power
LED is solid
green.
The power
LED is solid
green.
For a command switch,
the LED displays C.
For a member switch,
the LED displays S.
For a candidate switch,
the LED displays c.
The LED displays 1 if
there is only one unit.
The LED displays the
utilization of the power
supply.
81 - 100%
61 - 80%
41 - 60%
21 - 40%
0 - 20%
1-17
Installation Manual
H3C S5500-EI Series Ethernet Switches Chapter 1 Product Overview
LED Mark Status Description
A 1000 Mbps link is
10/100/1000Base
-T Ethernet port
status LED
—
Green
present. When data is
being received or sent,
the LED flashes at a
high frequency.
A 10/100 Mbps link is
Speed
Yellow
present. When data is
being received or sent,
the LED flashes at a
high frequency.
Duplex
PoE
Flashing
yellow (3 Hz)
The port fails the POST.
OFF No link is present.
The port works in the full
duplex mode. The LED
Green
flashes at a high
frequency when data is
being received or sent.
The port works in the
half duplex mode. The
Yellow
LED flashes at a high
frequency when data is
being received or sent
Flashing
yellow (3 Hz)
The port fails the POST.
OFF No link is present.
Solid green
The port supplies power
normally.
The required power of
the attached device
exceeds the maximum
Flashing
green (1 Hz)
power that the port can
supply.
The total power reaches
the maximum power, so
the port stops supplying
power.
1-18
Solid yellow
Flashing
yellow (3 Hz)
The device attached to
the port is not a powered
device (PD), so the port
cannot supply power.
A PoE failure occurs, so
the port cannot supply
power.
The port fails the POST.
Installation Manual
H3C S5500-EI Series Ethernet Switches Chapter 1 Product Overview
LED Mark Status Description
SFP port status
LED (1000 Mbps)
SFP port status
LED (100 Mbps)
—
—
The
Mode
button
has no
effect on
the LED.
Speed
Duplex
OFF
Green
Flashing
yellow (3 Hz)
OFF No link is present.
Yellow
Flashing
yellow (3 Hz)
OFF No link is present.
Green
The port does not supply
power.
A 1000 Mbps link is
present. When data is
being received or sent,
the LED flashes at a
high frequency.
The port fails the POST.
A 100 Mbps link is
present. When data is
being received or sent,
the LED flashes at a
high frequency.
The port failed the
POST.
The port operates in the
full duplex mode. When
data is being received or
sent, the LED flashes at
a high frequency.
1.6 S5500-52C-PWR-EI
1.6.1 Appearance
The S5500-52C-PWR-EI provides forty-eight auto-sensing 10/100/1000Base-T
Ethernet ports, four 1000Base-X SFP ports and one console port on the front panel,
and one AC powe r socket, one RPS port , and two 10 GE interface modul e slot s on the
rear panel.
Figure 1-14 shows the appearance of the S5500-52C-PWR-EI.
Flashing
yellow (3 Hz)
OFF No link is present.
The port fails the POST.
1-19
Installation Manual
H3C S5500-EI Series Ethernet Switches Chapter 1 Product Overview
Figure 1-13 Appearance of the S5500-52C-PWR-EI
1.6.2 Front Panel
(1) Auto-sensing 10/100/1000Base-T Ethernet port status LEDs
(2) Console port (3) 7-segment digital LED
(4) Mode button (5) Mode LED
(6) Power LED (7) RPS LED
(8) LED for extended module slot 1 (9) LED for extended module slot 2
(10) SFP port status LED
Figure 1-14 Front panel of the S5500-52C-PWR-EI
1.6.3 Rear Panel
(1) (2)
(1) (2) (3) (4) (5)
(3) (6)
(4) (5) (1) (2)
(3) (6)
(4) (5) (1) (2)
(3) (6)
(4) (5) (1) (2)
(3) (6)
(4) (5)
(10 )
(10 )
(10 )
(10 )
(7)
(7)
(7)
(7)
(8)
(8)
(8)
(8)
(9)
(9)
(9)
(9)
(1) RPS port (2) AC power socket
(3) Grounding screw (4) Extended module slot 1
(5) Extended module slot 2
Figure 1-15 Rear panel of the S5500-52C-PWR-EI
1-20
Installation Manual
H3C S5500-EI Series Ethernet Switches Chapter 1 Product Overview
1.6.4 Power Supply System
The S5500-52C-PWR-EI can adopt AC power input, or DC power input, or both to
provide backup.
z AC power input
Rated voltage range: 100 VAC to 240 VAC, 50 Hz or 60 Hz
Input voltage range: 90 VAC to 264 VAC, 47 Hz or 63 Hz
Only the RPS recommended by H3C can be used for the S5500-52C-PWR-EI. The –48
VDC power supply in the equipment room cannot be used directly. Otherwise, the
device may be damaged.
z DC power input
Rated voltage range: –52 VDC to –55 VDC
1.6.5 Cooling System
The S5500-52C-PWR-EI is equipped with six fans for heat dissipation.
1.6.6 LEDs
The LEDs on the front panel of the S5500-52C-PWR-EI are the same as those of the
S5500-28C-PWR-EI. For details, see
1.7 S5500-28F-EI
1.7.1 Appearance
The S5500-28F-EI provides twenty-four 1000Base-X SFP ports, eight auto-sensing
10/100/1000Base-T Ethernet ports, and one console port on the front panel, and two
AC or DC power sockets and two extended module slots on the rear panel.
Figure 1-16 shows the appearance of the S5500-28F-EI.
Table 1-5.
Figure 1-16 Appearance of the S5500-28F-EI
1-21
Installation Manual
H3C S5500-EI Series Ethernet Switches Chapter 1 Product Overview
1.7.2 Front Panel
(1) (2) (3) (4) (5) (6) (7) (8)
(1) 100/1000Base-X SFP port status LED
(3) Console port (4) 7-segment digital LED
(5) System status LED (6) LED for power module slot 2
(7) LED for power module slot 1 (8) LED for extended module slot 1
(9) LED for extended module slot 2 (10) Mode LED
(11) Mode button
Figure 1-17 Front panel of the S5500-28F-EI
1.7.3 Rear Panel
(1)
(1)
(1)
(1)
(1)
(1)
(1) Grounding screw (2) Power module slot 1
(3) Power module slot 2 (4) Extended module slot 1
(5) Extended module slot 2
Figure 1-18 Rear panel of the S5500-28F-EI
(11) (10) (9)
(2) Auto-sensing 10/100/1000Base-T
Ethernet port status LEDs
(2) (3) (4) (5)
(2) (3) (4) (5)
(2) (3) (4) (5)
(2) (3) (4) (5)
(2) (3) (4) (5)
(2) (3) (4) (5)
1.7.4 Power System
The S5500-28F-EI can adopt two hot-swappable AC or DC power modules to provide
backup.
z AC power input
Rated voltage range: 100 VAC to 240 VAC, 50 Hz or 60 Hz
Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz
z DC power input
Rated voltage range: –48 VDC to –60 VDC
Input voltage range: –36 VDC to –72 VDC
1-22
Loading...