How it Works
H3C
Loading...
R
S
Loading...
Loading...
S3100-26C-EPON-EI
User Manual
101 pgs1.52 Mb0
Quick Start Manual
80 pgs925.67 Kb0
Table of contents
Loading...

H3C S3100-8C-SI,S3100-16C-SI,S3100-26C-SI,S3100-SI,S3100-T-SI,S3100-8T-SI,S3100-16T-SI,S3100-26T-SI,S3100-TP-EI,S3100-8TP-EI,S3100-16TP-EI,S3100-26TP-EI,S3100-TP-PWR-EI,S3100-8TP-PWR-EI,S3100-16TP-PWR-EI,S3100-26TP-PWR-EI,S3100-EI,S3100-C-EPON-EI,S3100-8C-EPON-EI,S3100-16C-EPON-EI,S3100-26C-EPON-EI, S3100-8C-SI, S3100-16C-SI, S3100-26C-SI, S3100-SI User Manual

...
H3C S3100 Series Ethernet Switches
Installation Manual
Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com
Manual Version: 20080115-C-1.04
All Rights Reserved
No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of Hangzhou H3C Technologies Co., Ltd.
Trademarks
H3C, , Aolynk, , H3Care, Neocean, NeoVTL, SecPro, SecPoint, SecEngine, SecPath, Comware, Secware, Storware, NQA, VVG, V HUASAN are trademarks of Hangzhou H3C Technologies Co., Ltd.
All other trademarks that may be mentioned in this manual are the property of their respective owners.
Notice
The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the content s, but all statements, information, and recommendations in this document do not constitute the warranty of any kind, express or implied.
To obtain the latest information, please access: http://www. h3c.com
Technical Support
customer_service@h3c.com http://www. h3c.com
, TOP G, , IRF, NetPilot,
2
G, VnG, PSPT, XGbus, N-Bus, TiGem, InnoVision and
About This Manual
Related Documentation
In addition to this manual, each H3C S3100 Series Ethernet Switches documentation set includes the following:
Manual Description
Organization
H3C S3100 Series Ethernet Switches Installation Manual is organized as follows:
H3C S3100 Series Ethernet Switches Operation Manual
H3C S3100 Series Ethernet Switches Command Manual
Chapter Contents
1 Product Introduction
2 Installation Preparation
3 Installation
It is used for assisting the users in data configurations and typical applications.
It is used for assisting the users in using various commands.
Introduces the characteristics and technical specifications of S3100 Series Ethernet Switches.
Introduces the installation preparation and precaution of S3100 Series Ethernet Switches.
Introduces the procedures to install an S3100 Series Ethernet Switch, including the setup of the mainframe, cards and cables.
4 First Power-on
5 Boot ROM and Host Software Loading
6 Maintenance and Troubleshooting
Introduces the booting process of an S3100 Series Ethernet Switch, including the power-on booting of the switch and the system initialization.
Introduces how to load Boot ROM and host software for an S3100 Series Ethernet Switch.
Introduces the problems that might occur during the installation and the booting of an S3100 Series Ethernet Switch and the related solution.
Chapter Contents
Conventions
The manual uses the following conventions:

I. GUI conventions

7 Appendix Lightning Protection of the Switch
Convention Description
< >
[ ]
/
Button names are inside angle brackets. For example, click <OK>.
Window names, menu items, data table and field names are inside square brackets. For example, pop up the [New User] window.
Multi-level menus are separated by forward slashes. For example, [File/Create/Folder].
Introduces lightning protection of S3100 Series Ethernet Switches.

II. Symbols

Convention Description
Warning
Caution
Note Means a complementary description.
Environmental Protection
This product has been designed to comply with the requirements on environmental protection. For the proper storage, use and disposal of this product, national laws and regulations must be observed.
Means reader be extremely careful. Improper operation may cause bodily injury.
Means reader be careful. Improper operation may cause data loss or damage to equipment.
Installation Manual H3C S3100 Series Ethernet Switches Table of Contents
Table of Contents
Chapter 1 Product Introduction...................................................................................................1-1
1.1 Overview............................................................................................................................1-1
1.1.1 S3100-SI Series Ethernet Switches........................................................................1-1
1.1.2 S3100-EI Series Ethernet Switches........................................................................1-2
1.2 Introduction to S3100-SI Series Ethernet Switches...........................................................1-3
1.2.1 S3100-26T-SI..........................................................................................................1-3
1.2.2 S3100-16T-SI..........................................................................................................1-4
1.2.3 S3100-8T-SI............................................................................................................1-5
1.2.4 S3100-26C-SI..........................................................................................................1-7
1.2.5 S3100-16C-SI..........................................................................................................1-8
1.2.6 S3100-8C-SI..........................................................................................................1-10
1.3 Introduction to S3100-EI Series Ethernet Switches.........................................................1-11
1.3.1 S3100-26TP-EI......................................................................................................1-11
1.3.2 S3100-16TP-EI......................................................................................................1-13
1.3.3 S3100-8TP-EI........................................................................................................1-14
1.3.4 S3100-26TP-PWR-EI............................................................................................1-16
1.3.5 S3100-16TP-PWR-EI............................................................................................1-18
1.3.6 S3100-8TP-PWR-EI..............................................................................................1-20
1.3.7 S3100-26C-EPON-EI............................................................................................ 1-21
1.3.8 S3100-16C-EPON-EI............................................................................................ 1-23
1.3.9 S3100-8C-EPON-EI.............................................................................................. 1-24
1.4 Introduction to Front Panel LEDs.....................................................................................1-25
1.4.1 Front Panel LEDs of the S3100-SI/S3100-TP-PWR-EI/S3100-C-EPON-EI Series1-25
1.4.2 Front Panel LEDs of the S3100-TP-EI Series.......................................................1-27
1.5 Technical Specifications .................................................................................................. 1-28
1.5.1 S3100-SI Series Ethernet Switch.......................................................................... 1-28
1.5.2 S3100-EI Series Ethernet Switch.......................................................................... 1-31
1.6 SFP Modules Supported by S3100-EI Ethernet Switches ..............................................1-34
1.7 ONU Modules .................................................................................................................. 1-34
Chapter 2 Installation Preparation...............................................................................................2-1
2.1 Precautions........................................................................................................................2-1
2.2 Requirements on Environment..........................................................................................2-1
2.2.1 Temperature/Humidity Requirements..................................................................... 2-1
2.2.2 Cleanness Requirements........................................................................................2-2
2.2.3 Anti-interference Requirements .............................................................................. 2-3
2.2.4 Laser Usage Security..............................................................................................2-3
2.3 Installation Tools................................................................................................................2-3
i
Installation Manual H3C S3100 Series Ethernet Switches Table of Contents
Chapter 3 Installation....................................................................................................................3-1
3.1 Installing a Switch.............................................................................................................. 3-1
3.1.1 Cabinet Mounting.................................................................................................... 3-1
3.1.2 Desk Mounting ...................................................................................................... 3-11
3.1.3 Wall Mounting........................................................................................................3-11
3.1.4 Magnet Mounting...................................................................................................3-13
3.2 Installing an Expansion Interface Module........................................................................3-15
3.3 Connection of Power Cable and Grounding Cable..........................................................3-16
3.3.1 Connecting AC Power Cable ................................................................................ 3-16
3.3.2 Connecting DC Power Cable................................................................................ 3-18
3.3.3 Connecting Grounding Cable................................................................................ 3-21
3.4 Connecting Optical Fiber.................................................................................................3-23
3.5 Connection of Console Cable.......................................................................................... 3-23
3.5.1 Console Cable....................................................................................................... 3-23
3.5.2 Connecting Console Cable ................................................................................... 3-24
3.6 Installation Verification.....................................................................................................3-25
Chapter 4 First Power-on.............................................................................................................. 4-1
4.1 Establishing Configuration Environment............................................................................ 4-1
4.2 Connecting the Console Cable..........................................................................................4-1
4.3 Setting Terminal Parameters.............................................................................................4-1
4.4 Booting Switch................................................................................................................... 4-4
4.4.1 Checking Before Powering on the Switch...............................................................4-4
4.4.2 Powering on the Switch........................................................................................... 4-4
4.4.3 Changing the Startup Mode....................................................................................4-6
Chapter 5 Boot ROM and Host Software Loading ..................................................................... 5-1
5.1 Introduction to Loading Approaches..................................................................................5-1
5.2 Local Software Loading.....................................................................................................5-1
5.2.1 Boot Menu...............................................................................................................5-2
5.2.2 Loading Software Using XModem Through Console Port......................................5-3
5.2.3 Loading Software Using TFTP Through Ethernet Port........................................... 5-8
5.2.4 Loading Software Using FTP Through Ethernet Port............................................. 5-9
5.3 Remote Software Loading...............................................................................................5-11
5.3.1 Remote Loading Using FTP..................................................................................5-11
5.3.2 Remote Loading Using TFTP................................................................................5-13
Chapter 6 Maintenance and Troubleshooting............................................................................ 6-1
6.1 Software Loading Failure...................................................................................................6-1
6.2 Missing Password..............................................................................................................6-1
6.2.1 Missing user password............................................................................................ 6-1
6.2.2 Missing Boot ROM Password ................................................................................. 6-2
6.3 Power System Failure........................................................................................................ 6-2
6.4 Configuration System Failure ............................................................................................ 6-2
ii
Installation Manual H3C S3100 Series Ethernet Switches Table of Contents
iii
Installation Manual H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction

Chapter 1 Product Introduction

1.1 Overview

The H3C S3100 Series Ethernet Switches are high-performance, high-density, easy-to-install, NMS-manageable intelligent Ethernet switches which support wire-speed Layer 2 switching.
Table 1-1 lists the models of the H3C S3100 Series Ethernet Switches.
Table 1-1 Models of the H3C S3100 Series Ethernet Switches
Name Subseries Model
z S3100-8C-SI
H3C S3100 Series Ethernet Switches
S3100-SI
S3100-EI
S3100-C-SI
S3100-T-SI
S3100-TP-EI
S3100-TP-PWR-EI
S3100-C-EPON-EI
z S3100-16C-SI z S3100-26C-SI
z S3100-8T-SI z S3100-16T-SI z S3100-26T-SI
z S3100-8TP-EI z S3100-16TP-EI z S3100-26TP-EI
z S3100-8TP-PWR-EI z S3100-16TP-PWR-EI z S3100-26TP-PWR-EI
z S3100-8C-EPON-EI z S3100-16C-EPON-EI z S3100-26C-EPON-EI
1.1.1 S3100-SI Series Ethernet Switches
Currently, the S3100-SI Series Ethernet Switches include the S3100-T-SI and the S3100-C-SI, as listed in
Table 1-2 H3C S3100-T-SI Series Ethernet Switches
Model
S3100-26T-SI 24 Two Ethernet ports S3100-16T-SI 16 S3100-8T-SI
Table 1-2 and Table 1-3.
Power
input
Number of
10/100 Mbps
electrical ports
AC
8
1-1
Number of
gigabit uplink
ports
One Ethernet port
Number of
console
ports
1
Installation Manual H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction
Table 1-3 H3C S3100-C-SI Series Ethernet Switches
Model Power input
10/100 Mbps
electrical ports
S3100-26C-SI 24 2
AC input for AC-powered
S3100-16C-SI 16 2
switches. DC input for
S3100-8C-SI
DC-powered
8 1
switches
1.1.2 S3100-EI Series Ethernet Switches
Currently, the H3C S3100-EI Series Ethernet Switches include the S3100-TP-EI, the S3100-TP-PWR-EI and the S3100-C-EPON-EI, as listed in
Table 1-4 Models of the H3C S3100-TP-EI and S3100-TP-PWR-EI Series Ethernet Switches
Number of
Model Power input
10/100 Mbps
electrical
Number of
ports
Number of expansion
slots
Table 1-4 and Table 1-5.
Number of 1000
Mbps uplink
ports
Number of
console
ports
1
Number of
console
ports
S3100-26TP­EI
S3100-16TP­EI
S3100-8TP-EI S3100-26TP-
PWR-EI S3100-16TP-
PWR-EI S3100-8TP-P
WR-EI
AC input for AC-powered switches
DC input for DC-powered switches
AC or RPS DC input
AC input
24
16
Two Combo ports
Two Combo ports
1
1
8 One Combo port 1
24
16
Two Combo ports
Two Combo ports
1
1
8 One Combo port 1
1-2
Installation Manual H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction
Table 1-5 Models of the H3C S3100-C-EPON-EI Series Ethernet Switches
Model
Power
input
Number
of 10/100
Mbps
electrical
ports
Number of 1000 Mbps
uplink
PON ports
Number of expansion
slots
S3100-26C-EPON-EI 24 1 1 S3100-16C-EPON-EI 16 1 Disabled S3100-8C-EPON-EI
AC input
8 1 —

1.2 Introduction to S3100-SI Series Ethernet Switches

1.2.1 S3100-26T-SI
I. Front panel
S3100-26T-SI Ethernet switches each provide twenty-four auto-sensing 10/100Base-TX Ethernet ports, two 10/100/1000Base-T Ethernet ports, and one console port.
Figure 1-1 shows the front panel of an S3100-26T-SI Ethernet switch.
Number
of
console
ports
1
(1) Power LED (2) A/L LED (3) D/S LED (4) Port status LED, left (yellow) (5) Port status LED, right (green) (6) 10/100 Base-TX port (7) 10/100/1000 Base-T port (8) Console port (9) LINK LED (green) (10) ACT LED (yellow) (11) Mode button
Figure 1-1 Front panel of an S3100-26T-SI Ethernet switch
Note:
For details about LEDs on the front panel, refer to section 1.4.1 “Front Panel LEDs of the S3100-SI/S3100-TP-PWR-EI/S3100-C-EPON-EI Series”.
1-3
Installation Manual H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction
II. Rear panel
Figure 1-2 shows the rear panel of an S3100-26T-SI Ethernet switch.
(1) AC power socket (2) Grounding screw
Figure 1-2 Rear panel of an S3100-26T-SI Ethernet switch
III. Power system
S3100-26T-SI Ethernet switches support AC input.
z Rated voltage range: 100 VAC to 240 VAC, 50 Hz/60 Hz z Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz
IV. Cooling system
The S3100-26T-SI cools off naturally.
1.2.2 S3100-16T-SI
I. Front panel
S3100-16T-SI Ethernet switches each provide sixteen auto-sensing 10/100Base-TX Ethernet ports, one 10/100/1000Base-T Ethernet port, and one console port.
Figure 1-3 shows the front panel of an S3100-16T-SI Ethernet switch.
(1) Power LED (2) A/L LED (3) D/S LED (4) Port status LED, left (yellow) (5) Port status LED, right (green) (6) 10/100 Base-TX port (7) 10/100/1000 Base-T port (8) Console port (9) LINK LED (green) (10) ACT LED (yellow) (11) Mode button
Figure 1-3 Front panel of an S3100-16T-SI Ethernet switch
1-4
Installation Manual H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction
Note:
For details about LEDs on the front panel, refer to section 1.4.1 “Front Panel LEDs of the S3100-SI/S3100-TP-PWR-EI/S3100-C-EPON-EI Series”.
II. Rear panel
Figure 1-4 shows the rear panel of an S3100-16T-SI Ethernet switch.
(1) AC power socket (2) Grounding screw
Figure 1-4 Rear panel of an S3100-16T-SI Ethernet switch
III. Power system
S3100-16T-SI Ethernet switches support AC input.
z Rated voltage range: 100 VAC to 240 VAC, 50 Hz/60 Hz z Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz
IV. Cooling system
The S3100-16T-SI cools off naturally.
1.2.3 S3100-8T-SI
I. Front panel
S3100-8T-SI Ethernet switches each provide eight auto-sensing 10/100Base-TX Ethernet ports, one 10/100/1000Base-T Ethernet port, and one console port.
Figure 1-5 shows the front panel of an S3100-8T-SI Ethernet switch.
1-5
Installation Manual H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction
(1) Power LED (2) A/L LED (3) D/S LED (4) Port status LED, left (yellow) (5) Port status LED, right (green) (6) 10/100 Base-TX port (7) 10/100/1000 Base-T port (8) Console port (9) LINK LED (green) (10) ACT LED (yellow) (11) Mode button
Figure 1-5 Front panel of an S3100-8T-SI Ethernet switch
Note:
For details about LEDs on the front panel, refer to section 1.4.1 “Front Panel LEDs of the S3100-SI/S3100-TP-PWR-EI/S3100-C-EPON-EI Series”.
II. Rear panel
Figure 1-6 shows the rear panel of an S3100-8T-SI Ethernet switch.
(1) AC power socket (2) Grounding screw
Figure 1-6 Rear panel of an S3100-8T-SI Ethernet switch
III. Power system
S3100-8T-SI Ethernet switches support AC input.
z Rated voltage range: 100 VAC to 240 VAC, 50 Hz/60 Hz z Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz
IV. Cooling system
The S3100-8T-SI cools off naturally.
1-6
Installation Manual H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction
1.2.4 S3100-26C-SI
Both AC-powered switch es and DC-powered switches are available to this model.
I. Front panel
S3100-26C-SI Ethernet switches each provide twenty-four auto-sensing 10/100Base-TX Ethernet ports, two expansion slots, and one console port.
S3100-26C-SI Ethernet switches have the same front panel, as shown in
Figure 1-7.
(1) Power LED (2) A/L LED (3) D/S LED (4) Port status LED, left (yellow) (5) Port status LED, right (green) (6) 10/100Base- TX port (7) Expansion slot (8) Console port (9) Mode button
Figure 1-7 Front panel of an S3100-26C-SI Ethernet switch
Note:
z With a PoE card inserted in one expansion slot, an S3100-26C-SI Ethernet switch
will be a powered device (PD). In this case, the other expansion slot becomes unavailable.
z For details about LEDs on the front panel, refer to section 1.4.1 “Front Panel LE Ds
of the S3100-SI/S3100-TP-PWR-EI/S3100-C-EPON-EI Series”.
II. Rear panel
Figure 1-8 shows the rear panel of an S3100-26C-SI AC-powered Ethernet switch.
(1) AC power socket (2) Grounding screw
Figure 1-8 Rear panel of an S3100-26C-SI AC-powered Ethernet switch
1-7
Installation Manual H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction
Figure 1-9 shows the rear panel of an S3100-26C-SI DC-powered Ethernet switch.
(1) DC input terminal block (2) Grounding screw
Figure 1-9 Rear panel of an S3100-26C-SI DC-powered Ethernet switch
III. Power system
1) S3100-26C-SI AC-powered Ethernet switches:
z Rated voltage range: 100 VAC to 240 VAC, 50 Hz/60 Hz z Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz
2) S3100-26C-SI DC-powered Ethernet switches:
z Rated voltage range: –48 VDC to –60 VDC z Input voltage range: –36 VDC to –72 VDC
IV. Cooling system
The S3100-26C-SI cools off naturally.
1.2.5 S3100-16C-SI
Both AC-powered switch es and DC-powered switches are available to this model.
I. Front panel
S3100-16C-SI Ethernet switches each provide sixteen auto-sensing 10/100Base-TX Ethernet ports, two expansion slots, and one console port.
S3100-16C-SI Ethernet switches have the same front panel, as shown in
(1) Power LED (2) A/L LED (3) D/S LED (4) Port status LED, left (yellow) (5) Port status LED, right (green) (6) 10/100Base- TX port (7) Expansion slot (8) Console port (9) Mode button
Figure 1-10.
Figure 1-10 Front panel of an S3100-16C-SI Ethernet switch
1-8
Installation Manual H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction
Note:
z With a PoE card inserted in one expansion slot, an S3100-16C-SI Ethernet switch
will be a powered device (PD). In this case, the other expansion slot becomes unavailable.
z For details about LEDs on the front panel, refer to section 1.4.1 “Front Panel LE Ds
of the S3100-SI/S3100-TP-PWR-EI/S3100-C-EPON-EI Series”.
II. Rear panel
Figure 1-11 shows the rear panel of an S3100-16C-SI AC-powered Ethernet switch.
(1) AC power socket (2) Grounding screw
Figure 1-11 Rear panel of an S3100-16C-SI AC-powered Ethernet switch
Figure 1-12 shows the rear panel of an S3100-16C-SI DC-powered Ethernet switch.
(1) DC input terminal block (2) Grounding screw
Figure 1-12 Rear panel of an S3100-16C-SI DC-powered Ethernet switch
III. Power system
1) S3100-16C-SI AC-powered Ethernet switches:
z Rated voltage range: 100 VAC to 240 VAC, 50 Hz/60 Hz z Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz
2) S3100-16C-SI DC-powered Ethernet switches:
z Rated voltage range: –48 VDC to –60 VDC z Input voltage range: –36 VDC to –72 VDC
IV. Cooling system
The S3100-16C-SI cools off naturally.
1-9
Installation Manual H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction
1.2.6 S3100-8C-SI
Both AC-powered switch es and DC-powered switches are available to this model.
I. Front panel
S3100-8C-SI Ethernet switches each provide eight auto-sensing 10/100Base-TX Ethernet ports, one expansion slot, and one console port.
S3100-8C-SI Ethernet switches have the same front panel, as shown in
Figure 1-13.
(1) Power LED (2) A/L LED (3) D/S LED (4) Port status LED, left (yellow) (5) Port status LED, right (green) (6) 10/100Base- TX port (7) Expansion slot (8) Console port (9) Mode button
Figure 1-13 Front panel of an S3100-8C-SI Ethernet switch
Note:
For details about LEDs on the front panel, refer to section 1.4.1 “Front Panel LEDs of the S3100-SI/S3100-TP-PWR-EI/S3100-C-EPON-EI Series”.
II. Rear panel
Figure 1-14 shows the rear panel of an S3100-8C-SI AC-powered Ethernet switch.
(1) AC power socket (2) Grounding screw
Figure 1-14 Rear panel of an S3100-8C-SI AC-powered Ethernet switch
1-10
Installation Manual H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction
Figure 1-15 shows the rear panel of an S3100-8C-SI DC-powered Ethernet switch.
(1) DC input terminal block (2) Grounding screw
Figure 1-15 Rear panel of an S3100-8C-SI DC-powered Ethernet switch
III. Power system
1) S3100-8C-SI AC-powered Ethernet switches:
z Rated voltage range: 100 VAC to 240 VAC, 50 Hz/60 Hz z Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz
2) S3100-8C-SI DC-powered Ethernet switches:
z Rated voltage range: –48 VDC to –60 VDC z Input voltage range: –36 VDC to –72 VDC
IV. Cooling system
The S3100-8C-SI cools off naturally.

1.3 Introduction to S3100-EI Series Ethernet Switches

1.3.1 S3100-26TP-EI
Both AC-powered switch es and DC-powered switches are available to this model.
I. Front panel
S3100-26TP-EI Ethernet switches each provide twenty-four auto-sensing 10/100Base-TX Ethernet ports, two auto-sensing 10/100/1000Base-T Ethernet ports, two 100/1000Base-X SFP ports, and one console port. Each SFP port and the corresponding auto-sensing 10/100/1000Base- T Ethernet port form a Combo port. For each Combo port, either the SFP port or the corresponding 10/100/1000Base- T Ethernet port can be used at a time.
S3100-26TP-EI Ethernet switches have the same front panel, as shown in
Figure 1-16.
1-11
Installation Manual H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction
(1) (2) (4)
(7)
(1) Auto-sensing 10/100Base-TX port Speed LED (green) (2) Auto-sensing 10/100Base-TX port (3) Combo port Speed LED (green) (4) Auto-sensing 10/100/1000Base-T port (5) Console port (6) 100/1000Base-X SFP port (7) LINK/ACT LED (green) (8) Power LED (PWR)
(3)
(7)(8)
(6)
(5)
Figure 1-16 Front panel of an S3100-26TP-EI Ethernet switch
Note:
For details about LEDs on the front panel, refer to section 1.4.2 Front Panel LEDs of the S3100-TP-EI Series .
II. Rear panel
Figure 1-17 shows the rear panel of an S3100-26TP-EI AC-powered Ethernet switch.
(1) (2)
(1) Grounding screw (2) AC input terminal block
Figure 1-17 Rear panel of an S3100-26TP-EI AC-powered Ethernet switch
Figure 1-18 shows the rear panel of an S3100-26TP-EI DC-powered Ethernet switch.
(1) (2)
(1) Grounding screw (2) DC input terminal block
Figure 1-18 Rear panel of an S3100-26TP-EI DC-powered Ethernet switch
III. Power system
1) S3100-26TP-EI AC-powered Ethernet switches:
1-12
Installation Manual
(
1)(
2
H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction
z Rated voltage range: 100 VAC to 240 VAC, 50 Hz/60 Hz z Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz
2) S3100-26TP-EI DC-powered Ethernet switches:
z Rated voltage range: –48 VDC to –60 VDC z Input voltage range: –36 VDC to –72 VDC
IV. Cooling system
The S3100-26TP-EI cools off naturally.
1.3.2 S3100-16TP-EI
Both AC-powered switch es and DC-powered switches are available to this model.
I. Front panel
S3100-16TP-EI Ethernet switches each provide sixteen auto-sensing 10/100Base-TX Ethernet ports, two auto-sensing 10/100/1000Base-T Ethernet ports, two 100/1000Base-X SFP ports, and one console port. Each SFP port and the corresponding auto-sensing 10/100/1000Base- T Ethernet port form a Combo port. For each Combo port, either the SFP port or the corresponding 10/100/1000Base- T Ethernet port can be used at a time.
S3100-16TP-EI Ethernet switches have the same front panel, as shown in
)
(7)
(8)
(1) Auto-sensing 10/100Base-TX port Speed LED (green) (2) Auto-sensing 10/100Base-TX port (3) Combo port Speed LED (green) (4) Auto-sensing 10/100/1000Base-T port (5) Console port (6) 100/1000Base-X SFP port (7) LINK/ACT LED (green) (8) Power LED (PWR)
(3)
(7)
Figure 1-19.
(4)
(6)
(5)
Figure 1-19 Front panel of an S3100-16TP-EI Ethernet switch
Note:
For details about LEDs on the front panel, refer to section 1.4.2 Front Panel LEDs of the S3100-TP-EI Series
1-13
Installation Manual H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction
II. Rear panel
Figure 1-20 shows the rear panel of an S3100-16TP-EI AC-powered Ethernet switch.
(1) (2)
(1) Grounding screw (2) AC input terminal block
Figure 1-20 Rear panel of an S3100-16TP-EI AC-powered Ethernet switch
Figure 1-21 shows the rear panel of an S3100-16TP-EI DC-powered Ethernet switch.
(1) (2)
(1) Grounding screw (2) DC input terminal block
Figure 1-21 Rear panel of an S3100-16TP-EI DC-powered Ethernet switch
III. Power system
1) S3100-16TP-EI AC-powered Ethernet switches:
z Rated voltage range: 100 VAC to 240 VAC, 50 Hz/60 Hz z Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz
2) S3100-16TP-EI DC-powered Ethernet switches:
z Rated voltage range: –48 VDC to –60 VDC z Input voltage range: –36 VDC to –72 VDC
IV. Cooling system
The S3100-16TP-EI cools off naturally.
1.3.3 S3100-8TP-EI
Both AC-powered switch es and DC-powered switches are available to this model.
I. Front panel
S3100-8TP-EI Ethernet switches each provide eight auto-sensing 10/100Base-TX Ethernet ports, one auto-sensing 10/100/1000Base-T Ethernet ports, one 100/1000Base-X SFP ports, and one consol e port. The SFP port and the auto-sensing 10/100/1000Base- T Ethernet port form a Combo port. For the Combo port, either the SFP port or the 10/100/1000Base- T Ethernet port can be used at a time.
1-14
Installation Manual H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction
S3100-8TP-EI Ethernet switches have the same front panel, as shown in Figure 1-22.
(1) (2) (4)
(7)
(1) Auto-sensing 10/100Base-TX port Speed LED (green) (2) Auto-sensing 10/100Base-TX port (3) Combo port Speed LED (green) (4) Auto-sensing 10/100/1000Base-T port (5) Console port (6) 100/1000Base-X SFP port (7) LINK/ACT LED (green) (8) Power LED (PWR)
(3)
(6)(7)(8)
(5)
Figure 1-22 Front panel of an S3100-8TP-EI Ethernet switch
Note:
For details about LEDs on the front panel, refer to section 1.4.2 Front Panel LEDs of the S3100-TP-EI Series .
II. Rear panel
Figure 1-23 shows the rear panel of an S3100-8TP-EI AC-powered Ethernet switch.
(1) (2)
(1) Grounding screw (2) AC input terminal block
Figure 1-23 Rear panel of an S3100-8TP-EI AC-powered Ethernet switch
Figure 1-24 shows the rear panel of an S3100-8TP-EI DC-powered Ethernet switch.
1-15
Installation Manual H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction
(1) (2)
(1) Grounding screw (2) DC input terminal block
Figure 1-24 Rear panel of an S3100-8TP-EI DC-powered Ethernet switch
III. Power system
1) S3100-8TP-EI AC-powered Ethernet switches:
z Rated voltage range: 100 VAC to 240 VAC, 50 Hz/60 Hz z Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz
2) S3100-8TP-EI DC-powered Ethernet switches:
z Rated voltage range: –48 VDC to –60 VDC z Input voltage range: –36 VDC to –72 VDC
IV. Cooling system
The S3100-8TP-EI cools off naturally.
1.3.4 S3100-26TP-PWR-EI
I. Front panel
S3100-26TP-PWR-EI Ethernet switches each provide twenty-four auto-sensing 10/100Base-TX Ethernet ports, two 10/100/1000Base-T Ethernet ports, two 100/1000Base SFP ports, and one console port. Each SFP port an d the corresponding 10/100/1000Base- T Ethernet port form a Combo port. For each Combo po rt, either the SFP port or the corresponding 10/100/1000Base- T Ethernet port can be used at a time.
Figure 1-25 shows the front panel of an S3100-26TP-PWR-EI Ethernet switch.
1-16
Installation Manual H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction
(1) (2) (3) (4)
(5)(6)(7)(8)
(1) Auto-sensing 10/100Base-TX Ethernet port status LED (2) LINK LED for Combo port (3) Console port (4) Power LED (PWR) (5) A/L LED (6) D/S LED (7) Mode button (8) ACT LED for Combo port
Figure 1-25 Front panel of an S3100-26TP-PWR-EI Ethernet switch
Note:
For details about LEDs on the front panel, refer to section 1.4.1 “Front Panel LEDs of the S3100-SI/S3100-TP-PWR-EI/S3100-C-EPON-EI Series”.
II. Rear panel
(1) (2) (3)
(1) AC power socket (2) DC power socket (3) Grounding screw
Figure 1-26 Rear panel of an S3100-26TP-PWR-EI Ethernet switch
III. Power system
S3100-26TP-PWR-EI Ethernet switches support AC input or DC input.
1) AC input
z Rated voltage range: 100 VAC to 240 VAC, 50 Hz/60 Hz z Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz
2) DC input
z Rated voltage range: –52 VDC to –56 VDC
1-17
Installation Manual H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction
Note:
Only the recommended RPS can be used for S3100-26TP-PWR-EI Ethernet switches. The –48 VDC in the equipment room cannot be used directly. Otherwise, the device may be damaged.
IV. Cooling system
The S3100-26TP-PWR-EI has four fans for heat dissipation.
1.3.5 S3100-16TP-PWR-EI
I. Front panel
S3100-16TP-PWR-EI Ethernet switches each provide sixteen auto-sensing 10/100Base-TX Ethernet ports, two 10/100/1000Base-T Ethernet ports, two 100/1000Base SFP ports, and one console port. Each SFP port an d the corresponding 10/100/1000Base-T Ethernet port form a Combo port. For e ach Combo port, eith er the SFP port or the corresponding 10/100/1000Base-T Ethern et port can be used at a time.
Figure 1-27 shows the front panel of an S3100-16TP-PWR-EI Ethernet switch.
(1) (2) (3) (4)
(5)(6)(7)(8)
(1) Auto-sensing 10/100Base-TX Ethernet port status LED (2) LINK LED for Combo port (3) Console port (4) Power LED (PWR) (5) A/L LED (6) D/S LED (7) Mode button (8) ACT LED for Combo port
Figure 1-27 Front panel of an S3100-16TP-PWR-EI Ethernet switch
1-18
Installation Manual H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction
Note:
For details about LEDs on the front panel, refer to section 1.4.1 “Front Panel LEDs of the S3100-SI/S3100-TP-PWR-EI/S3100-C-EPON-EI Series”.
II. Rear panel
(1) (2)
(1) AC power socket (2) Grounding screw
Figure 1-28 Rear panel of an S3100-16TP-PWR-EI Ethernet switch
III. Side panel
Each S3100-16TP-PWR-EI Ethernet switch provides a security slot , through which you can lock the device together with an irremovable object to prevent theft.
The security slot is located at the rear end of the left side panel, as shown in
Figure
1-29.
(1)
(1) Security slot
Figure 1-29 Security slot on left side panel of an S3100-16TP-PWR-EI Ethernet switch
Note:
If the left screw hole above the security slot is used, the security slot cannot be used.
1-19
Installation Manual H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction
IV. Power system
S3100-16TP-PWR-EI Ethernet switches support AC input.
z Rate voltage range: 100 VAC to 240 VAC, 50 Hz/60 Hz z Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz
V. Cooling system
The S3100-16TP-PWR-EI has two fans for heat dissipation.
1.3.6 S3100-8TP-PWR-EI
I. Front panel
S3100-8TP-PWR-EI Ethernet switches each provide eight auto-sensing 10/100Base-TX Ethernet ports, one 10/100/1000Base-T Ethernet port, one 100/1000Base SFP ports, and one console port. The SFP port and the 10/100/1000Base-T Ethernet port form a Combo port. Either the SFP port or the 10/100/1000Base-T Ethernet port can be used at a time.
Figure 1-30 shows the front panel of an S3100-8TP-PWR-EI Ethernet switch.
(1) (2) (3) (4)
(5)(6)(7)(8)
(1) Auto-sensing 10/100Base-TX Ethernet port status LED (2) LINK LED for Combo port (3) Console port (4) Power LED (PWR) (5) A/L LED (6) D/S LED (7) Mode button (8) ACT LED for Combo port
Figure 1-30 Front panel of an S3100-8TP-PWR-EI Ethernet switch
Note:
For details about LEDs on the front panel, refer to section 1.4.1 “Front Panel LEDs of the S3100-SI/S3100-TP-PWR-EI/S3100-C-EPON-EI Series”.
1-20
Installation Manual H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction
II. Rear panel
(1) (2)
(1) AC power socket (2) Grounding screw
Figure 1-31 Rear panel of an S3100-8TP-PWR-EI Ethernet switch
III. Side panel
Each S3100-8TP-PWR-EI Ethernet switch provides a security slot, through which you can lock the device together with an irremovable object to prevent theft.
The security slot is located at the rear end of the left side panel, as shown in 1-29.
Note:
If the left screw hole above the security slot is used, the security slot cannot be used.
IV. Power system
S3100-8TP-PWR-EI Ethernet switches support AC input.
z Rate voltage range: 100 VAC to 240 VAC, 50 Hz/60 Hz z Input voltage range: 90 VAC to 264 VAC, 47 HZ to 63 Hz
V. Cooling system
The S3100-8TP-PWR-EI has two fans for heat dissipation.
1.3.7 S3100-26C-EPON-EI
Figure
I. Front panel
The S3100-26C-EPON-EI provides 24 x 10/100Base-TX ports, one Gigabit uplink PON port, one expansion slot, and one console port.
Figure 1-32 shows the front view of the S3100-26C-EPON-EI.
1-21
Installation Manual H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction
(1): Power Led (PWR) (2): A/L LED (3): D/S LED (4): Port status LED, left (yellow) (5): Port status LED, right (green) (6): 10/100 Base-TX port (7): ONU module (8): Console port (9): LINK LED for the uplink PON port (10): ACT LED for the uplink PON port (11): 1000 Mbps uplink PON port (12): Expansion slot (13): MODE button
Figure 1-32 Front panel of the S3100-26C-EPON-EI
Note:
z The S3100-26C-EPON-EI provides one expansion slot. You can order one more
ONU module (1000Base- PX20) as needed. For more information about ONU modules, refer to section
z For details about the LEDs on the front panel, refer to section 1.4.1 “Front Panel
1.7 “ONU Modules”.
LEDs of the S3100-SI/S3100-TP-PWR-EI/S3100-C-EPON-EI Series”.
II. Rear panel
(1) AC power socket (2) Grounding screw
Figure 1-33 Rear panel of an S3100-26C-EPON-EI Ethernet switch
III. Power system
S3100-26C-EPON-EI Ethernet switches support AC input.
z Rated voltage range: 100 VAC to 240 VAC, 50 Hz/60 Hz z Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz
IV. Cooling system
The S3100-26C-EPON-EI has one fan for heat dissipation.
1-22
Installation Manual H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction
1.3.8 S3100-16C-EPON-EI
I. Front panel
The S3100-16C-EPON-EI provides 16 x 10/100Base-TX Ethernet ports, one 1000 Mbps uplink PON port, and one console port.
Figure 1-34 shows the front panel of the S3100-16C-EPON-EI.
(1): Power Led (PWR) (2): A/L LED (3): D/S LED (4): Port status LED, left (yellow) (5): Port status LED, right (green) (6): 10/100 Base-TX port (7): ONU module (8): Console port (9): LINK LED for the uplink PON port (10): ACT LED for the uplink PON port (11): 1000 Mbps uplink PON port (12): Expansion slot (disabled) (13): MODE button
Figure 1-34 Front panel of the S3100-16C-EPON-EI
Note:
z The S3100-16C-EPON-EI supports only one ONU module (required). z For details about the LEDs on the front panel, refer to section 1.4.1 “Front Panel
LEDs of the S3100-SI/S3100-TP-PWR-EI/S3100-C-EPON-EI Series”.
II. Rear panel
(1) AC power socket (2) Grounding screw
Figure 1-35 Rear panel of an S3100-16C-EPON-EI Ethernet switch
III. Power system
S3100-16C-EPON-EI Ethernet switches support AC input.
z Rated voltage range: 100 VAC to 240 VAC, 50 Hz/60 Hz z Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz
1-23
Loading...
+ 71 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use