H3C S12500 LST1LB1A1, LSQ1NSMSC0 User Manual
Manual version: 6PW101-20141219 BOM: 3123A0BY
2: CF
p
H3C S12500 LST1LB1A1 Card Manual
1 Card identifier
The card identifier LST1LB1A1 is at the upper right corner of the front panel.
2 Introduction
The LST1LB1A1 card provides one console port, one CF card interface, two USB interfaces, two
10/100/1000BASE-T Ether n e t c o p p er interfaces, and two Gigabit Combo interfaces.
You can use a GE port or combo interface to provide the following functions:
• In-band management.
• Outgoing interface for log messages.
• Failover interface for stateful failover.
3 Specifications
Figure 1 Front panel
1: CF card button
3: CF card LED (CFS) 4: Console port (CONSOLE)
5: USB ports (hardware reserved, software not support)
6: 10/100/1000BASE-T management Ethernet ports (GE1 and GE2)
7: Management Ethernet port LEDs
8: 10/100/1000BASE-T copper combo ports (GE3 and GE4)
9: 1000BASE-X fiber combo ports (SFP3 and SFP4) 10: Combo interface LEDs
11: Ejector lever 12: Captive screw
card slot (CF CARD)
Table 1 Card specifications
Item S
ecification
CF card
Dimensions (H × W × D) 40.1mm X399.2mm X498.8mm(1.58 × 15.72 × 19.64 in)
Power consumption 94.5W~125.2W
Weight 4.3 kg (9.48 lb)
One CF card slot, 256MB by default for the external CF card
256 MB, 512 MB, or 1 GB for an optional external CF card
i
Manual version: 6PW101-20141219 BOM: 3123A0BY
p
p
Item Specification
Hot swapping Supported
• 1 console port
• 2 USB ports (reserved for future use)
• 2 pairs of combo ports, each pair containing the following ports:
Ports
Ambient temperature
Ambient relative humidity
Compatible device models H3C S12500 series switches
System software version See the release notes that come with the card.
{ 1 x 10/100/1000BASE-T copper port
{ 1 x 1000BASE-X SFP fiber port
You can use the combo enable { copper | fiber } command to activate either of
the ports in a pair. By default, the copper combo port is activated.
• Operating: 0°C to 45°C (32°F to 113°F)
• Not operating: –40°C to +70°C (–40°F to +158°F)
• Operating: 10% to 95%, noncondensing
• Non-operating: 5% to 95%, noncondensing
Table 2 Console port specifications
Item S
Connector RJ-45
Interface standard RS-232
Transmission baud rate 9600 bps (default) to 115200 bps
Transmission medium Asynchronous serial cable
Transmission distance ≤15 m (49.21 ft)
ecification
• Provides connection to an ASCII terminal.
Services
• Provides connection to the serial port of a local or remote PC (through a
pair of modems) that is running a terminal emulation program.
• Supports command line interface (CLI).
Table 3 10/100/1000BASE-T copper port specifications
Item S
Connector RJ-45
Interface standard 802.3, 802.3u, and 802.3ab
Interface type MDI/MDIX autosensing
Supported cable Category-5 (or above) twisted pair cable
ecification
Transmission distance 100 m (328.08 ft)
• 10 Mbps, half/full duplex
Operating mode
• 100 Mbps, half/full duplex
• 1000 Mbps, full duplex
ii
Loading...