Page 1
H3C LSWM116Q interface card
user manual-6PW104
▌Introduction
Overview
The LSWM116Q interface card provides 16 QSFP+ ports.
Figure 1 Front panel
(1) QSFP+ port LED (2) QSFP+ port
QSFP+ ports
Table 1 and Table 2 describe QSFP+ transceiver modules and Table 3
describes QSFP+ cables available for the QSFP+ ports on the card.
Table 1 QSFP+ transceiver modules available for the QSFP+
ports (1)
QSFP+ transceiver
module
QSFP-40G-SR4-M
M850
QSFP-40G-CSR4MM850
QSFP-40G-LR4-PS
M1310
QSFP-40G-BIDI-SR
-MM850
Central wavelength
(nm)
850
850
1310
850 LC
1
Connector
MPO (PC polished,
12-fiber)
MPO (PC polished,
12-fiber)
MPO (APC polished,
12-fiber)
Page 2
QSFP+ transceiver
module
Central wavelength
(nm)
Connector
Four lanes:
QSFP-40G-LR4-W
DM1300
• 1271
• 1291
• 1311
LC
• 1331
Four lanes:
QSFP-40G-LR4L-W
DM1300
• 1271
• 1291
• 1311
LC
• 1331
Table 2 QSFP+ transceiver modules available for the QSFP+
ports (2)
QSFP+
transceiver
module
QSFP-40G-SR4
-MM850
QSFP-40G-CS
R4-MM850
QSFP-40G-LR4
-PSM1310
QSFP-40G-BIDI
-SR-MM850
QSFP-40G-LR4
-WDM1300
Cable/fiber
diameter
(µm)
Multi-mode,
50/125
Multi-mode,
50/125
Single-mode,
9/125
Multi-mode,
50/125
Single-mode,
9/125
Modal
bandwidth
(MHz × km)
Max
transmission
distance
2000 100 m (328.08 ft)
4700 150 m (492.12 ft)
2000 300 m (984.25 ft)
4700
N/A
400 m (1312.33
ft)
10 km (6.21
miles)
2000 100 m (328.08 ft)
4700 150 m (492.12 ft)
N/A
10 km (6.21
miles)
2
Page 3
QSFP+
r
transceiver
module
QSFP-40G-LR4
L-WDM1300
Table 3 QSFP+ cables available for the QSFP+ ports
QSFP+ cable Cable length Data rate
QSFP+ copper cable
LSWM1QSTK0 1 m (3.28 ft)
LSWM1QSTK1 3 m (9.84 ft)
LSWM1QSTK2 5 m (16.40 ft)
QSFP+ fiber cable
QSFP-40G-D-AOC-7M 7 m (22.97 ft)
QSFP-40G-D-AOC-10M 10 m (32.81 ft)
QSFP-40G-D-AOC-20M 20 m (65.62 ft)
NOTE:
• As a best practice, use H3C transceiver modules and cables fo
the interface card.
• The transceiver module and cable types supported by an
interface card vary by device model. For more information, see
the installation guide or contact H3C Support or marketing staff.
For more information about H3C transceiver modules and cables, see
H3C Transceiver Modules User Guide at www.h3c.com.
Cable/fiber
diameter
(µm)
Single-mode,
9/125
Modal
bandwidth
(MHz × km)
N/A
Max
transmission
distance
2 km (1.24
miles)
40 Gbps
40 Gbps
LEDs
Table 4 describes QSFP+ port LEDs on the front panel.
3
Page 4
Table 4 QSFP+ port LED description
LED status Description
Steady green
Flashing green The port is sending or receiving data at 40 Gbps.
Off
A transceiver module is installed in the port. The
port is operating at 40 Gbps, and a link is
present on the port.
No transceiver module is installed in the port, or
no link is present on the port.
▌Installing and removing the card
CAUTION:
• Before you install or remove the card, wear an ESD wrist strap
and make sure the strap makes good skin contact and is
reliably grounded.
• To avoid device damage, do not use excessive force when you
install or remove the card.
• The LSWM116Q interface card is hot swappable. However, do
not install or remove it during the startup of the switch.
Installing the card
1. Remove the filler panel (if any) from the target slot.
Keep the removed filler panel secure for future use.
2. Unpack the interface card.
Figure 2 LSWM116Q interface card
(1) Ejector lever (2) Latch
4
Page 5
3. Press the latch on the card to release the ejector lever.
4. As shown by callout 1 in Figure 3, i
slot along the guide rails.
5. Rotate inward the ejector lever as shown by callout 2 in Figure 3
until the
Figure 3 Installing an LSWM116Q interface card
latch locks the ejector lever in place.
nsert the card slowly into the
Removing the card
1. Prepare an anti-static bag.
2. Remove the cables from the card.
3. Press the latch to release the ejector lever
4. Rotate outward the ejector lever as shown by callout 1 in Figure 4.
5. Pull out
6. Place th
7. If you are not to install a new card, install a filler panel in the slot to
the interface card slowly out of the interface card slot, as
shown by callout 2 in Figure 4.
e removed interface card in the anti-static bag.
prevent dust and ensure good ventilation in the device.
5
Page 6
Figure 4 Removing an LSWM116Q interface card
Installing and removing QSFP+ transceiver modules or cables
For information about installing and removing QSFP+ transceiver
modules and cables, see H3C Transceiver Modules and Network
Cables Installation Guide at www.h3c.com.
Verifying the installation
After the installation is complete, determine whether the card is
operating correctly.
If the card fails to operate correctly, perform the following steps:
1. Reinstall the card following the installation procedures described
in this document.
2. If the problem persists, contact H3C Support.
▌Technical support
New H3C Technologies Co., Ltd. provides customers with
comprehensive technical support and service. If you purchase the
products from the sales agent of New H3C Technologies Co., Ltd.,
please contact our sales agent or technical personnel.
Website: http://www.h3c.com
BOM: 3101A0KJ
6
Loading...