H3C LS-S5600-50C-OVS, LS-S5600-50C-PWR-OVS, LS-S5600-26F, LS-S5600-26C-PWR-OVS, LS-S5600-26C-OVS User Manual

H3C S5600 Series Ethernet Switches

Installation Manual

Hangzhou H3C Technologies Co., Ltd. http://www.h3c.com

Manual Version: T2-08045W-20071218-C-1.04

No part of this manual may be reproduced or transmitted in any form or by any means without prior written consent of Hangzhou H3C Technologies Co., Ltd.

Trademarks

H3C, , Aolynk, , H3Care, Neocean, NeoVTL, SecPro, SecPoint, SecEngine, SecPath, Comware, Secware, Storware, NQA, VVG, V HUASAN are trademarks of Hangzhou H3C Technologies Co., Ltd.

All other trademarks that may be mentioned in this manual are the property of their respective owners.

Notice

The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the content s, but all statements, information, and recommendations in this document do not constitute the warranty of any kind, express or implied.

To obtain the latest information, please access: http://www. h3c.com

Technical Support

customer_service@h3c.com http://www. h3c.com

, TOP G, , IRF, NetPilot,

G, VnG, PSPT, XGbus, N-Bus, TiGem, InnoVision and

About This Manual

I. GUI conventions

Convention Description

< >

[ ]

Button names are inside angle brackets. For example, click <OK>.

Window names, menu items, data table and field names are inside square brackets. For example, pop up the [New User] window.

Multi-level menus are separated by forward slashes. For example, [File/Create/Folder].

II. Symbols

Convention Description

Means reader be extremely careful. Improper operation

Warning

Caution

 Note Means a complementary description.

may cause bodily injury. Means reader be careful. Improper operation may cause

data loss or damage to equipment.

Environmental Protection

This product has been designed to comply with the requirements on environmental protection. For the proper storage, use and disposal of this product, national laws and regulations must be observed.

Installation Manual H3C S5600 Series Ethernet Switches Table of Contents

Table of Contents

Chapter 1 Product Overview........................................................................................................1-1

1.1 Overview............................................................................................................................1-1

1.2 S5600-26C/S5600-26C-PWR/S5600-26F Ethernet Switch ..............................................1-2

1.2.1 Front Panel.............................................................................................................. 1-2

1.2.2 Rear Panel ............................................................................................................ 1-10

1.3 S5600-50C/S5600-50C-PWR Ethernet Switch ............................................................... 1-11

1.3.1 Front Panel............................................................................................................ 1-11

1.3.2 Rear panel.............................................................................................................1-12

1.4 Power system .................................................................................................................. 1-13

1.5 Cooling system ................................................................................................................ 1-13

1.6 Attributes of 1000 Mbps SFP port....................................................................................1-14

1.7 Expansion Module...........................................................................................................1-15

1.8 S5600 Series Technical Specifications ...........................................................................1-18

Chapter 2 Preparing for Installation............................................................................................2-1

2.1 Safety Precautions............................................................................................................. 2-1

2.2 Installation Site...................................................................................................................2-1

2.2.1 Temperature/Humidity.............................................................................................2-1

2.2.2 Cleanness ............................................................................................................... 2-2

2.2.3 Electromagnetic Susceptibility ................................................................................ 2-2

2.2.4 Laser Safety............................................................................................................2-3

2.3 Installation Tools................................................................................................................ 2-3

Chapter 3 Installing the Switch.................................................................................................... 3-1

3.1 Rack-Mounting the Switch................................................................................................. 3-1

3.1.1 Introduction to mounting ear ................................................................................... 3-1

3.1.2 Introduction to guide rail..........................................................................................3-2

3.1.3 Use front mounting ears and a tray......................................................................... 3-3

3.1.4 Use front and rear mounting ears ........................................................................... 3-4

3.1.5 Use front mounting ears and guide rails................................................................. 3-7

3.2 Mounting the Switch on a Tabletop/Workbench................................................................ 3-9

3.3 Installing/Removing the Power Module...........................................................................3-10

3.3.1 Installing the Power Module.................................................................................. 3-10

3.3.2 Removing the Power Module................................................................................ 3-10

3.4 Connecting the Power Cord and the Ground Wire.......................................................... 3-11

3.4.1 Connecting the AC-Input Power Cord................................................................... 3-11

3.4.2 Connecting the DC-Input Power Cord ..................................................................3-12

3.4.3 Connecting the Ground Wire.................................................................................3-13

3.5 Connecting the Switch to a Console Terminal................................................................. 3-16

Installation Manual H3C S5600 Series Ethernet Switches Table of Contents

3.5.1 Console Cable....................................................................................................... 3-16

3.5.2 Connecting the Console Cable ............................................................................. 3-16

3.6 Installing/Removing the Stack Cable............................................................................... 3-17

3.6.1 Stack Cable........................................................................................................... 3-17

3.6.2 Installing the Stack Cable......................................................................................3-17

3.6.3 Removing the Stack Cable....................................................................................3-18

3.7 Installing/Removing the Optional Interface Module......................................................... 3-18

3.8 Verifying Installation......................................................................................................... 3-19

Chapter 4 Starting up the Switch at the Initial Boot .................................................................. 4-1

4.1 Setting up a Configuration Environment............................................................................4-1

4.2 Connecting the Console Cable.......................................................................................... 4-1

4.3 Setting Terminal Parameters............................................................................................. 4-1

4.4 Booting the Switch.............................................................................................................4-4

4.4.1 Verifying Installation before Power-up .................................................................... 4-4

4.4.2 Powering up the Switch........................................................................................... 4-4

Chapter 5 Loading Boot ROM and Host Software .....................................................................5-1

5.1 Introduction to Loading Approaches..................................................................................5-1

5.2 Loading Software Locally...................................................................................................5-1

5.2.1 Boot Menu............................................................................................................... 5-1

5.2.2 Loading Software from Console Port Using XModem............................................5-3

5.2.3 Loading Software from an Ethernet Port Using TFTP ............................................ 5-7

5.2.4 Loading Software from an Ethernet Port Using FTP...............................................5-9

5.3 Loading Software Remotely.............................................................................................5-10

5.3.1 Loading Software Remotely Using FTP................................................................5-10

5.3.2 Loading Software Remotely Using TFTP..............................................................5-11

Chapter 6 Maintenance and Troubleshooting............................................................................ 6-1

6.1 Dealing with Loading Failures............................................................................................6-1

6.2 Dealing with Password Loss..............................................................................................6-1

6.3 Dealing with Power System Failures.................................................................................6-1

6.4 Dealing with Configuration System Failures......................................................................6-1

Installation Manual H3C S5600 Series Ethernet Switches Chapter 1 Product Overview

Chapter 1 Product Overview

1.1 Overview

H3C S5600 Series Ethernet Switches are high-performance, high-density, easy-to-install, NMS-manageable intelligent Ethernet switches which support wire-speed Layer2/3 switching.

Table 1-1 lists the models of H3C S5600 Series Ethernet Switches.

Table 1-1 Models of H3C S5600 Series Ethernet Switches

Number of

Model

S5600-26C S5600-26C-PWR S5600-26F 4 24 S5600-50C S5600-50C-PWR

Each SFP port and the corresponding 10/100/1000M Ethernet port form a Combo port. For each Combo port, the SFP port and the 10/100/1000M Ethernet port cannot be used at the same time. For the relationship between the Combo ports and the Ethernet ports, refer to

Table 1-2 Combo port list

Switch model Combo Port Corresponding port

Table 1-2.

10/100/1000M

electrical ports

24 4

48 4

25 22

Number of

1000M SFP

optical ports

Number of

Console ports

S5600-26C/S5600-26C

-PWR/S5600-26F

S5600-50C/S5600-50C

-PWR

26 24 27 21 28 23 49 46 50 48 51 45 52 47

1-1

Installation Manual H3C S5600 Series Ethernet Switches Chapter 1 Product Overview

 Note:

z The electrical ports of S5600-26C-PWR/S5600-50C-PWR are capable of supply ing

-48 VDC power to remote PDs (powered devices, such as S2016C, S2008B, S2016B, S2016-EI, and so on).

z The S5600-26C-PWR/S5600-50C-PWR adopts PoE power module, which provides

AC/DC power to PD devices. When delivering the AC input, the module can supply up to 300 W power. If more power is needed, use the DC input or both AC and DC inputs to ensure the operation of all the connected devices.

z The S5600-26C-PWR/S5600-50C-PWR can also adopt AC/DC dual input power

module. In this case, however, the two types of switches have no PoE function. And they function exactly like the S5600-26C and S5600-50C.

1.2 S5600-26C/S5600-26C-PWR/S5600-26F Ethernet Switch

1.2.1 Front Panel

I. Front panel

The S5600-26C/S5600-26C-PWR provides 24 x 10/100/1000Base-TX Ethernet ports, one Console port, and four 1000 Mbps SFP Combo ports on its front panel. Each SFP port and the corresponding 10/100/1000M Ethernet port form a Combo port. For each Combo port, the SFP port and the 10/100/1000M Ethernet port cannot be used at the same time. For the relationship between the Combo ports and the Ethernet po rt s, refer

Table 1-2.

Figure 1-1 shows the front panel of an S5600-26C Ethernet swit ch.:

(1) 10/100/1000M auto-negotiation Ethernet port status LEDs (2) 1000 Mbps SFP Combo port LED (3) Console port (4) 7-segment digitron display (5) Power LED (6) DC LED (7) Fabric LED (8) Module LED (9) Port mode LED (10) Mode button

Figure 1-1 Front panel of the S5600-26C/S5600-26C-PWR

1-2

Installation Manual H3C S5600 Series Ethernet Switches Chapter 1 Product Overview

The S5600-26F provides 24 x 1000 Mbps SFP optical port s, one Console port, and four 1000 Mbps RJ-45 Combo ports on it s front panel. Each SFP port a nd the corresponding 10/100/1000M Ethernet port form a Combo port. For each Combo port, the SFP port and the 10/100/1000M Ethernet port cannot be used at the same time. For the relationship between the Combo ports and the Ethernet ports, refer to

Table 1-2.

Figure 1-2. shows the front panel of an S5600-26F Ethernet switch.:

(1) SFP optical port status LED (2) 10/100/1000M auto-negotiation Ethernet port status LEDs: left one for speed, right one for duplex mode (3) Console port (4) 7-segment digitron display (5) Power LED (6) RPS LED (7) Fabric LED (8) Modul e LED

Figure 1-2 Front panel of the S5600-26F

II. LEDs

The S5600-26C/S5600-26C-PWR provides one power LED, one RPS LED, one fabric LED, one module LED, one mode LED, one 7-segment digitron display, four pairs of 1000 Mbps SFP port status LEDs, and 24 pairs of 10/100/1000M port status LEDs on its front panel.

The S5600-26F provides one power LED, one RPS LED, one fabric LED, one module LED, one 7-segment digitron display , 24 pairs of 1000 Mbp s SFP port status LEDs, and four pairs of 10/100/1000M auto-negotiation Ethernet port status LEDs on its front panel.

Table 1-3 and Table 1-4 describe respectively the LEDs on the S5600-26C/S5600-26C-PWR and S5600-26F.

1-3

Installation Manual H3C S5600 Series Ethernet Switches Chapter 1 Product Overview

Table 1-3 LEDs on the S5600-26C/S5600-26C-PWR

LED Mark Status Description

Mode LED Mode

Power LED

PWR

DC LED RPS

Speed Solid green

Duplex Solid yellow

PoE

Blinking green (at 1 Hz)

The port status LEDs are showing the speed of each port.

The port LEDs are showing the duplex mode of each port.

The port LEDs are showing the PoE status of each port.

Solid green The switch is started normally.

Blinking green (at 1 Hz)

Solid red

Blinking yellow (at 1 Hz)

The system is running power-on self-test (POST).

The system fails the POST, or there is another fault.

Some ports fail the POST and do not function.

OFF The switch is power-off.

Solid green

Both the AC power supply and the DC input operate normally.

The AC power supply fails or the

Solid yellow

AC input is disconnected, while the DC input operates normally.

Fabric LED

STK

OFF DC input is disconnected.

The device is in the ring fabric

Green

status; the LED blinks quickly when the fabric port is receiving or sending data.

The device is in the daisy chain

Yellow

fabric status; the LED blinks quickly when the fabric port is receiving or sending data.

This device is isolated from the

Blinking green (at 3 Hz)

whole set of fabric devices (effective when this device is in the fabric status).

OFF

Neither of the two fabric ports is connected.

1-4

Installation Manual H3C S5600 Series Ethernet Switches Chapter 1 Product Overview

LED Mark Status Description

Module LED

7-segment digitron display

Module (MOD)

Unit

Solid green

Blinking yellow

The module is seated and operates normally.

The module fails or is not supported.

OFF No module is installed.

The POST ID of the in-process POST running

Blinking green

test is displayed:

The POST ID of the failed test POST failed

Blinking red

blinks.

A light bar rotates clockwise

around the display during the Software downloading

Blinking green

downloading procedure.

An “F” is displayed. Fan failed Solid red

Over temperature alarm

Speed and duplex mode

PoE mode

Solid red

Solid green

A “t” is displayed.

UNIT ID in the fabric; or “1” for a

standalone unit is displayed.

The utilization of the power

supply is displayed.

81 - 100% 61 - 80% 41 - 60% 21 - 40% 0 - 20%

1-5

Installation Manual H3C S5600 Series Ethernet Switches Chapter 1 Product Overview

LED Mark Status Description

The port is operating at 1000

Green

Mbps. The LED blinks quickly

when the port is receiving or

sending data.

The port is operating at 10/100 Speed mode

Yellow

Mbps. The LED blinks quickly

when the port is receiving or

sending data.

Blinking yellow

The port fails the POST.

(at 3 Hz) OFF The port is not connected.

The port is operating in full

Green

duplex mode. The LED blinks

quickly when the port is

receiving or sending data.

The port is operating in half

duplex mode. The LED blinks

quickly when the port is

receiving or sending data.

The port fails the POST.

10/100/ 1000M autonegotiation Ethernet

—

Duplex mode

Yellow

Blinking Yellow (3 Hz)

port status LED

OFF The port is not connected.

PoE mode

Solid green

The port supplies power

normally.

The connected device requires

Blinking green (at 1 Hz)

more power than the maximum

power a port can supply.

The port cannot supply power

because the switch has reached

its maximum power supplied.

The port cannot supply power

because the connected device is

Solid yellow

not a PD.

The port cannot supply power

due to the power source failure

of PoE.

Blinking yellow (3

The port fails the POST.

Hz) OFF The port does not supply power.

1-6

Installation Manual H3C S5600 Series Ethernet Switches Chapter 1 Product Overview

LED Mark Status Description

The port is operating at 1000

Green

Mbps. The LED blinks quickly

when the port is receiving or

sending data. Speed mode

Blinking yellow (3

The port fails the POST.

Hz)

1000M Base SFP port mode LED

—

OFF The port is not connected.

The port is operating in 1000

Green

Mbps full duplex mode. The LED

blinks quickly when the port is

receiving or sending data. Duplex

mode

Blinking yellow (3

The port fails the POST.

Hz) OFF The port is not connected.

PoE mode OFF

–

Table 1-4 LEDs on the S5600-26F

LED Mark Status Description

Solid green The switch is started normally .

The system is running power-on

self-test (POST).

The system fails the POST, or

there is another fault.

Power LED

PWR

Blinking green (at 1 Hz)

Solid red

DC LED RPS

Blinking yellow (at 1 Hz)

Some ports fail the POST and

do not function.

OFF The switch is power-off.

Solid green

Both the AC power supply and

the DC input operate normally.

The AC power supply fails or the

Solid yellow

AC input is disconnected, while

the DC input operates normally.

OFF DC input is disconnected.

1-7

Installation Manual H3C S5600 Series Ethernet Switches Chapter 1 Product Overview

LED Mark Status Description

The device is in the ring fabric

Green

status; the LED blinks quickly

when the fabric port is receiving

or sending data.

The device is in the daisy chain

fabric status; the LED blinks

quickly when the fabric port is

receiving or sending data.

Fabric LED

Yellow

STK

This device is isolated from the

Blinking green (at 3 Hz)

whole set of fabric devices

(effective when this device is in

the fabric status).

Module LED

7-segment digitron display

Module (MOD)

Unit

OFF

Solid green

Blinking yellow

Neither of the two fabric ports is

connected.

The module is seated and

operates normally.

The module fails or is not

supported.

OFF No module is installed.

The POST ID of the in-process

POST running

Blinking green

test is displayed:

The POST ID of the failed test

POST failed

Blinking red

blinks.

A light bar rotates clockwise

around the display during the

Software downloading

Blinking green

downloading procedure.

An “F” is displayed.

Fan failed Solid red

Over temperature alarm

Speed and duplex mode

1-8

Solid red

Solid green

A “t” is displayed.

UNIT ID in the fabric; or “1” for a

standalone unit is displayed.

Installation Manual H3C S5600 Series Ethernet Switches Chapter 1 Product Overview

LED Mark Status Description

The port is operating at 1000

Green

Mbps. The LED blinks quickly

when the port is receiving or

sending data.

The port is operating at 10/100

Speed mode

Yellow

Mbps. The LED blinks quickly

when the port is receiving or

sending data.

Blinking

10/100/ 1000M autonegotiation Ethernet port status LED

—

yellow (at 3 Hz)

OFF The port is not connected.

Green

The port fails the POST.

The port is operating in full

duplex mode. The LED blinks

quickly when the port is

receiving or sending data.

The port is operating in half

Duplex mode

Yellow

duplex mode. The LED blinks

quickly when the port is

receiving or sending data.

Blinking Yellow

The port fails the POST.

(3 Hz) OFF The port is not connected.

The port is operating at 1000

Mbps. The LED blinks quickly

when the port is receiving or

sending data.

The port fails the POST.

1000Base SFP optical port status LED

—

Green

port status LED

Blinking yellow (3 Hz)

OFF The port is not connected.

III. Console port

The S5600-26C/S5600-26C-PWR/S5600-26F provides an EIA/TIA-232-compliant Console port, which enables you to configure the switch from the local or remote site.

Table 1-5 Attributes of the Console port

Item Description

Connector RJ-45 Standard EIA/TIA-232

1-9

Installation Manual H3C S5600 Series Ethernet Switches Chapter 1 Product Overview

Item Description

Baud rate 9600 bps (default), auto-negotiation is supported

Connection to an ASCII terminal

Services

Connection to the serial port of a local terminal (a PC for example) or a remote terminal (through a pair of modems) running terminal emulation software

1.2.2 Rear Panel

I. Rear panel

 Note:

The ports of the AC/DC dual input power module and the PoE power module are exactly the same, so only one rear panel illustration is shown below.

The S5600-26C/S5600-26C-PWR/S5600-26F provides two sockets for pluggable power module, two fabric ports, one expansion slot, and one grounding screw on its rear panel, as shown in the following figure.

(1) AC-input power socket for the power module (2) Expansion module (3) Grounding screw (4) Fabric ports (5) Fabric port LEDs (6) RPS LED (7) DC-input power socket for the power module

Figure 1-3 Rear panel of the S5600-26C/S5600-26C-PWR/S5600-26F

II. Fabric port

The fabric port marked with “UP” connects to a port of the same type on an upstream device; the fabric port marked with “DOWN” connects to a port of the same type on a downstream device.

1-10

Installation Manual H3C S5600 Series Ethernet Switches Chapter 1 Product Overview

Table 1-6 Fabric port LEDs

LED Mark Status Indicate

Solid green The fabric port is properly connected.

Fabric port LED

UP(DOWN)

Blinking green

The fabric port is properly connected and the port is receiving or sending data.

OFF The fabric port is disconnected.

1.3 S5600-50C/S5600-50C-PWR Ethernet Switch

1.3.1 Front Panel

I. Front panel

The S5600-50C/S5600-50C-PWR provides 48 x 10/100/1000Base-TX Ethernet ports, one Console port, and four 1000 Mbps SFP Combo ports on its front panel. Each SFP port and the corresponding 10/100/1000M Ethernet port form a Combo port. For each Combo port, the SFP port and the 10/100/1000M Ethernet port cannot be used at the same time. For the relationship between the Combo ports and the Ethernet po rt s, refer

Table 1-2.

to Figure 1-4 shows the front panel of an S5600-50C/S5600-50C-PWR Ethern et switch:

(1) 10/100/1000M auto-negotiation Ethernet port status LEDs (2) Console Port (3) 7-segment digitron display (4) Mode button (5) Mode LED (6) Power LED (7) RPS LED (8) Fabric LED (9) Module LED (10) 1000 Mbps SFP combo port LED

Figure 1-4 Front panel of the S5600-50C/S5600-50C-PWR

1-11

Installation Manual H3C S5600 Series Ethernet Switches Chapter 1 Product Overview

II. LEDs

The S5600-50C/S5600-50C-PWR provides one power LED, RPS LED, fabric LED, module LED, mode LED, 7-segment digitron display, 1000 Mbps SFP port status LED, and auto-negotiation Ethernet port status LED on its front panel. The meaning of each LED is shown in

Table 1-3

III. Console port

The S5600-50C/S5600-50C-PWR provides an EIA/TIA-232-compliant console port, which enables you to configure the switch from the local or remote site. For the attributes of the port, refer to

Table 1-5.

1.3.2 Rear panel

I. Rear panel

 Note:

The ports of the AC/DC dual input power module and the PoE power module are exactly the same, so only one rear panel illustration is shown below.

The S5600-50C/S5600-50C-PWR provides two sockets for pluggable power module, two fabric ports, one expansion slot, and one grounding screw on its rear panel, as shown in the following figure.

(1) AC-input power socket for the power module (2) Expansion module (3) Grounding screw (4) Fabric ports (5) Fabric port LEDs (6) RPS LED (7) DC-input power socket for the power module

Figure 1-5 Rear panel of the S5600-50C/S5600-50C-PWR

II. Fabric ports

For fabric ports and the meanings of their LEDs, refer to Table 1-6.

1-12

Installation Manual H3C S5600 Series Ethernet Switches Chapter 1 Product Overview

1.4 Power system

z AC power input range

Rated voltage: 100 to 240 VAC; 50/60 Hz Max. voltage range: 90 to 264 VAC; 50/60 Hz

z DC power input range

Rated voltage: –48 to–60 V Max. voltage range: –36 to–72 V

z AC input of the PoE power module

Rated voltage: 100 to 240 VAC; 50/60 Hz Max. voltage range: 90 to 264 VAC; 50/60 Hz

z DC input of the PoE power module

Rated voltage: –53.5 V Max. voltage range: –52 to –55 V

 Note:

The S5600-26C-PWR/S5600-50C-PWR must use the external PoE PSU recommended by H3C as its DC input, but not the -48VDC power supply generally available in the equipment room. Otherwise, the device may be damaged.

1.5 Cooling system

S3100-8TP-PWR-EI Ethernet switches each run two fans for heat dissipation.

Table 1-7 S5600 Ethernet switches cooling system

Model S5600-26C S5600-26C-PWR S5600-26F

Cooling system

Two fans are for the device and two are for the power supply module.

(1)

Two fans are for the device and four are for the power supply module.

Four fans are for the device and two are for the power supply module.

1-13

Installation Manual H3C S5600 Series Ethernet Switches Chapter 1 Product Overview

Table 1-8 S5600 Ethernet switches cooling system (2)

Model S5600-50C S5600-26C-PWR

Two fans are for the device

Cooling system

and two are for the power supply module.

1.6 Attributes of 1000 Mbps SFP port

The S5600-26C/S5600-26C-PWR/S5600-50C/S5600-50C-PWR provides 4 × 1000 Mbps SFP ports on it s front panel. Th e S5600-26F provides 24 × 1000 Mb ps SFP ports on its front panel.

SFP modules allow for great flexibility in networking because they are hot swappable and user configurable.

Table 1-9 lists the available SFP modules that you can select as required:

Table 1-9 Optical port module

Type Model

Two fans are for the device and four are for the power supply module.

SFP-GE-SX-MM850-A SFP-GE-LX-SM1310-A

SFP module

1000M SFP module

SFP-GE-LH40-SM1310 SFP-GE-LH40-SM1550 SFP-GE-LH70-SM1550

SFP electrical interface module SFP-GE-T

 Note:

z Only the optical module that H3C Technology provides or recommends can be

used.

z The types of SFP modules may vary with time. Consult H3C marketing personnel or

technical support personnel to obtain the latest information about SFP modules.

z For specifications of SFP modules, refer to H3C Low End Series Ethernet Switches

Pluggable Module Manual.

1-14

Installation Manual H3C S5600 Series Ethernet Switches Chapter 1 Product Overview

1.7 Expansion Module

The S5600 Series Ethernet switches provide one expansion module slot on the rear panel. The expansion mode that can be used in this slot includes 8-port 1000 Mbps SFP module, 1-port 10 Gbps XENPAK module, and 2-port 10 Gbps XFP module.

I. 8-port 1000 Mbps SFP module

(1) Port status LEDs (2) SFP ports (3) Module power LED

Figure 1-6 8-port 1000 Mbps SFP module

This module provides eight 1000 Mbps SFP external optical/electrical ports.

z For an optical port, you can choose one of the following SFP modules according to

your needs.

Table 1-10 Optical port module supported by 8-port 1000 Mbps SFP module

SFP module

Central wavelength

Maximum transmission distance

Fiber specifications

SFP-GE-SX-MM850-A

SFP module 1000M SFP module

SFP-GE-LX-SM1310-A SFP-GE-LH40-SM1310

 Note:

z The types of SFP modules may vary with time. Consult H3C marketing personnel or

technical support personnel to obtain the latest information about SFP modules.

z For specifications of SFP modules, refer to H3C Low End Series Ethernet Switches

Pluggable Module Manual.

z For an RJ-45 electrical port with the transmission distance is 100 m (328 ft), you

can select the RJ-45 connector as shown in the following figure, and the category-5 twisted pair as the data transmission medium.

1-15

Installation Manual H3C S5600 Series Ethernet Switches Chapter 1 Product Overview

Figure 1-7 RJ-45 connector

Table 1-11 Pinouts of the RJ-45 GE port

1000Base-TX

Signal Function

1 MX_0+ Data transmit/receive 2 MX_0- Data transmit/receive 3 MX_1+ Data transmit/receive 4 MX_2+ Data transmit/receive 5 MX_2- Data transmit/receive 6 MX_1- Data transmit/receive 7 MX_3+ Data transmit/receive 8 MX_3- Data transmit/receive

II. 2-port 10 Gbps XFP module

(1) Module power LED (2) Port status LEDs (3) 10 Gbps XFP optical ports

Figure 1-8 2-port 10 Gbps XFP module

This module provide two 10 Gbps XFP optical port. The following table lists the available XFP optical modules that you can select according to your need s:

1-16

+ 50 hidden pages