Page 1
H3C LSQM1TGT24QSM0 interface card
(1) 10GBASE-T port LED
(2) QSFP+ port LED
(3) QSFP+ port
(4) 10GBASE-T port
NOTE:
•
is currently applicable
•
Item
Specification
1
2
3
4
user manual-6PW103
▌Introduction
Overview
The LSQM1TGT24QSM0 interface card provides 24 10GBASE-T
ports and two QSFP+ ports.
Figure 1 LSQM1TGT24QSM0 interface card front panel
The LSQM1TGT24QSM0 interface card
only to H3C S7502E-XS and S7504E-XS switches. The
applicable switch models might change over time. For the
most recent list of applicable switch models, contact H3C
Support or marketing staff.
For more information about transceiver modules and cables
available, see H3C S7500E-XS Switch Series Transceiver
Modules Compatibility Matrixes.
10GBase-T ports
Table 1 10GBase-T port specifications
Connector type RJ-45
1
Page 2
Item
Specification
Port standard 1/10 Gbps full duplex, MDI/MDI-X auto-sensing
LED status
Description
LED status
Description
he
• Category-6 unshielded twisted pair cable:
Transmission
medium and max
transmission
distance
Compliance
standard
55 m (180.45 ft)
• Category-6 shielded twisted pair cable: 100
m (328.08 ft)
• Category-6A or above twisted pair cable:
100 m (328.08 ft)
• IEEE 802.3an
• IEEE 802.3ab
LEDs
Table 2 describes 10GBASE-T port LEDs. Table 3 describes QSFP+
port LEDs.
Table 2 10GBase-T port LED description
Steady green
Flashing green
Steady yellow
Flashing yellow The port is sending or receiving data at 1 Gbps.
Off No link is present on the port.
Table 3 QSFP+ port LED description
Steady green
Flashing green The port is sending or receiving data at 40 Gbps.
The port is operating at 10 Gbps, and a link is
present on the port.
The port is sending or receiving data at 10
Gbps.
The port is operating at 1 Gbps, and a link is
present on the port.
A transceiver module is installed in the port. T
port is operating at 40 Gbps, and a link is
present on the port.
2
Page 3
LED status
Description
Steady yellow
he
NOTE:
The
affected by the port mode switching button
more information about the port mode switching button, see
installation g
CAUTION:
•
•
T o avoid device damage, do not use excessive force when you
Flashing yellow The port is sending or receiving data at 10 Gbps.
Off
10GBASE-T port LEDs and QSFP+ port LEDs are not
A transceiver module is installed in the port. T
port is operating at 10 Gbps, and a link is
present on the port.
No transceiver module is installed in the port, or
no link is present on the port.
on your switch. For
uide of the switch.
the
▌Installing and removing an interface card
Installing an interface card
Before you install an interface card, remove the fi ller panel (if any)
from the target slot. Keep the removed fill er panel secure for future
use.
To install an interface card:
1. Unpack the interface card.
Before you install or remove an interface card, wear an ESD
wrist strap and make sure the strap makes good skin contact
and is reliably grounded.
install or remove an interface card.
3
Page 4
Figure 2 LSQM1TGT24QSM0 interface card
(1) Ejector lever
(2) Latch
CAUTION:
•
•
is to
1
2
1
2
2. Press the latch on the interface card to release the ejector lever.
3. As shown by callout 1 in Figure 3, insert the interface card slowly
into the slot along the guide rails.
4. Rotate inward the ejector lever as shown by callout 2 in Figure 3 until the latch locks the ejector lever in place.
Figure 3 Installing an LSQM1TGT24QSM0 interface card
Removing an interface card
Before you remove an interface card, remove the cable from it
to avoid cable damage.
After removing an interface card, if no new interface card
be installed, install the filler panel as soon as possible to
prevent dust and ensure good ventilation in the device.
4
Page 5
To remove an interface card:
1
2
1. Prepare an anti-static bag.
2. Press the latch to release the ejector lever
3. Rotate outward the ejector lever as shown by callout 1 in Figure 4.
4. Pull out the interface card slowly out of the interface card slot, as
shown by callout 2 in Figure 4.
5. Place the removed interface card in the anti-static bag.
Figure 4 Removing an LSQM1TGT24QSM0 interface card
Installing and removing QSFP+ transceiver modules and DAC cables
For information about installing and removing QSFP+ transceiver
modules and DAC cables, see H3C QSFP+ Transceiver
Modules/Cables Installation Guide at www.h3c.com.
Verifying the installation
After the installation is complete, identify whether the interface card is
operating correctly.
If the interface card fails to operate correctly, perform the following
steps:
1. Reinstall it fol lo wing the installation procedures described in this document.
2. If the problem persists, contact H3C Support.
5
Page 6
▌Technical support
New H3C Technologies Co., Ltd. provides customers with
comprehensive technical support and service. If you purchase the
products from the sales agent of New H3C Technologies Co., Ltd.,
please contact our sales agent or technical personnel.
Website: http://www.h3c.com
BOM: 3101A0K7
6
Loading...