H3C LSPM6G4T6 User Manual

Page 1
H3C LSPM6G4T6P interface card
user manual-6PW103

Introduction

Overview

The LSPM6G4T6P interface card provides four 10/100/1000Base-T autosensing Ethernet ports and six SFP ports. 10/100/1000Base-T autosensing Ethernet ports 5T and 6T form a combo interface with SFP ports 5S and 6S, respectively.
Figure 1 LSPM6G4T6P interface card
5 4
32
Ethernet port
Ethernet port LED
1
1
6
(1) SFP port (2) 10/100/1000Base-T autosensing
(3) Captive screw (4) 10/100/1000Base-T autosensing
(5) Ejector lever (6) SFP port LED
NOTE:
The H3C switch models that the LSPM6G4T6P interface card is applicable to might change over time. For the most recent list of applicable switch models, contact H3C Support or marketing staff.
Page 2

SFP ports

You can install the following transceiver modules and cables in the SFP ports on the card:
GE SFP transceiver modules in Table 1 and
FE SFP transceiver modules in Table 3 and
SFP cables in Table 5.
Table 1 GE SFP trans
Module Central wavelength (nm) Connector
SFP-GE-SX-MM850-A 850 LC SFP-GE-LX-SM1310-A 1310 LC SFP-GE-LH40-SM1310 1310 LC SFP-GE-LH40-SM1550 1550 LC SFP-GE-LH70-SM1550 1550 LC SFP-GE-LH80-SM1550 1550 LC SFP-GE-LH100-SM1550 1550 LC
SFP-GE-LX-SM1310-BIDI
SFP-GE-LX-SM1490-BIDI
SFP-GE-T N/A RJ-45
Table 2 GE SFP transceiver modules available for the SFP ports (2)
Module
SFP-GE-SX-MM 850-A
SFP-GE-LX-SM1 310-A
ceiver modules available for the SFP ports (1)
TX: 1310 RX: 1490 TX: 1490 RX: 1310
Cable/fiber diameter (μm)
Multi-mode, 50/125
Multi-mode,
62.5/125 Single-mode, 9/125 Multi-mode, 50/125 Multi-mode,
62.5/125
Modal bandwidth (MHz × km)
500 550 m (1804.46 ft) 400 500 m (1640.42 ft) 200 275 m (902.23 ft) 160 220 m (721.78 ft)
N/A 10 km (6.21 miles)
500 or 400
500 550 m (1804.46 ft)
2
Table 2.
Tabl e 4.
LC
Max transmission distance
550 m (1804.46 ft)
Page 3
Module
SFP-GE-LH40-S M1310 SFP-GE-LH40-S M1550 SFP-GE-LH70-S M1550 SFP-GE-LH80-S M1550 SFP-GE-LH100­SM1550
Cable/fiber diameter (μm)
Single-mode, 9/125 Single-mode, 9/125 Single-mode, 9/125 Single-mode, 9/125 Single-mode, 9/125
Modal bandwidth (MHz × km)
Max transmission distance
N/A 40 km (24.86 miles)
N/A 40 km (24.86 miles)
N/A 70 km (43.50 miles)
N/A 80 km (49.71 miles)
N/A
100 km (62.14 miles)
SFP-GE-LX-SM1 310-BIDI
SFP-GE-LX-SM1
Single-mode, 9/125
N/A 10 km (6.21 miles)
490-BIDI SFP-GE-T Twisted pair N/A 100 m (328.08 ft)
NOTE:
The SFP-GE-LX-SM1310-BIDI and SFP-GE-LX-SM1490-BIDI transceiver modules must be used in pairs.
Table 3 FE SFP transceiver modules available for the SFP ports (1)
Module Central wavelength (nm) Connector
SFP-FE-SX-MM1310-A 1310 LC SFP-FE-LX-SM1310-A 1310 LC SFP-FE-LH40-SM1310 1310 LC SFP-FE-LH80-SM1550 1550 LC
SFP-FE-LX-SM1310-BIDI
SFP-FE-LX-SM1550-BIDI
TX: 1310 RX: 1550 TX: 1550 RX: 1310
LC
LC
3
Page 4
Table 4 FE SFP transceiver modules available for the SFP ports (2)
A
g
Module Fiber diameter (μm)
SFP-FE-SX-MM13 10-A
SFP-FE-LX-SM13 10-A SFP-FE-LH40-SM 1310 SFP-FE-LH80-SM 1550 SFP-FE-LX-SM13 10-BIDI SFP-FE-LX-SM15 50-BIDI
Multi-mode, 50/125 2 km (1.24 miles) Multi-mode, 62.5/125 2 km (1.24 miles)
Single-mode, 9/125 15 km (9.32 miles)
Single-mode, 9/125 40 km (24.86 miles)
Single-mode, 9/125 80 km (49.71 miles)
Single-mode, 9/125 15 km (9.32 miles)
Single-mode, 9/125 15 km (9.32 miles)
Max transmission
distance
NOTE:
The SFP-FE-LX-SM1310-BIDI and SFP-FE-LX-SM1550-BIDI
transceiver modules must be used in pairs.
Only SFP ports 5S and 6S support FE SFP transceiver modules.
Table 5 SFP cables available for the SFP ports
Cable Cable length Data rate
SFP-STACK-Kit 1.5 m (4.92 ft) 1250 Mbps
NOTE:
s a best practice, use H3C SFP transceiver modules and SFP cables for the SFP ports on the card. The H3C SFP transceiver modules and SFP cables available for the SFP ports are subject to change over time. For the most recent list of H3C SFP transceiver modules and SFP cables available for the SFP ports, contact H3C Support or marketin staff.
4
Page 5
For more information about H3C SFP transceiver modules and SFP cables, see H3C SFP/SFP+/XFP/SFP28 Transceiver Modules and Cables Installation Guide at www.h3c.com.hk.

10/100/1000Base-T Ethernet interfaces

Table 6 10/100/1000Base-T Ethernet interface specifications
Item Specification
Connector RJ-45
Port mode
Maximum transmission distance Cable Category 5 or above twisted pair cables
Standard
10 Mbps, full duplex
100 Mbps, full duplex
1000 Mbps, full duplex
MDI/MDI-X autosensing
100 m (328.08 ft)
IEEE 802.3i
802.3u
802.3ab

LEDs

Tabl e 7 describes LEDs for the SFP ports.
Table 7 SFP port LED description
LED status Description
Steady green
Flashing green
Steady yellow (available only for the SFP ports 5 and 6) Flashing yellow (available only for the SFP ports 5 and 6)
A transceiver module is installed in the port. The port is operating at 1000 Mbps, and a link is present on the port. The port is sending or receiving data at 1000 Mbps. A transceiver module is installed in the port. The port is operating at 100 Mbps, and a link is present on the port.
The port is sending or receiving data at 100 Mbps.
5
Page 6
LED status Description
Off
Table 8 10/100/1000Base-T interface LED description
LED status Description
Steady green
Flashing green
Steady yellow
Flashing yellow
Off No link is present on the port.
NOTE:
The LEDs are affected by the port mode switching button on your switch. For more information about the port mode switching button, see the installation guide for the switch.
No transceiver module is installed in the port, or no link is present on the port.
The port is operating at 1000 Mbps, and a link is present on the port. The port is sending or receiving data at 1000 Mbps. The port is operating at 10/100 Mbps, and a link is present on the port. The port is sending or receiving data at 10/100 Mbps.

Installing and removing the card

CAUTION:
Before you install or remove the card, wear an ESD wrist strap and
make sure the wrist strap makes good skin contact and is reliably grounded.
To avoid device damage, do not use excessive force when you
install or remove the card.
The following procedures describe how to install and remove an LSPM6G4T6P interface card on an S5560-30C-EI switch.
Prepare the following tools before you install or remove the card:
6
Page 7
Phillips screwdriver.
Flat blade screwdriver.
ESD wrist strap.
The installation tools are not provided with H3C devices. Prepare them yourself.

Installing the card

1. Use the Phillips screwdriver to remove the screw on the filler panel in
the target slot, as shown by callout 1 in Figure 2.
K
eep the removed screw secure for future use.
2. Insert the flat blade screwdriver through the handle on the filler
panel to pull out the filler panel, as shown by callout 2 in Figure 2.
eep the removed filler panel secure for future use.
K
3. Unpack the card.
4. Insert the card slowly into the slot along the guide rails, as shown by
callout 1 in Figure 3.
5. Rotate in
6. Use the Phillips screwdriver to tighten the captive screw on the card,
Figure 2 Rem
ward the ejector lever as shown by callout 2 in Figure 3
card is in close contact with the switch.
until the
as shown by callout 3 in Figure 3.
oving the filler panel
7
Page 8
Figure 3 Installing the card

Removing the card

CAUTION:
Before you remove the card, remove the cable from it.
If you are not to install a new card after removing the original one,
install the filler panel in the slot to prevent dust and ensure good ventilation in the device.
To remove the card:
1. Prepare an anti-static bag.
2. Use the Phillips screwdriver to loosen the captive screw on the card,
as shown by callout 1 in Figure 4,
3. Rotate out
4. P
5. Place
ward the ejector lever as shown by callout 2 in Figure 4.
ull the card slowly out of the slot as shown by callout 3 in Figure 4.
the removed card in the anti-static bag.
8
Page 9
Figure 4 Removing the card
1
3
2

Installing and removing SFP transceiver modules or SFP cables

For information about installing or removing SFP transceiver modules or SFP cables, see H3C SFP/SFP+/XFP/SFP28 Transceiver Modules and Cables Installation Guide at www.h3c.com.hk.

Verifying the installation

After the installation is complete, identify whether the card is operating correctly according to the status of the port LEDs.
If the card fails to operate correctly, perform the following steps:
1. Reinstall it following the installation procedures described in this
document.
2. If the problem persists, contact H3C Support.

Technical support

New H3C Technologies Co., Ltd. provides customers with comprehensive technical support and service. If you purchase the products from the sales agent of New H3C Technologies Co., Ltd., please contact our sales agent or technical personnel.
Website: http:// www.h3c.com.hk E-mail: service@h3c.com BO M : 3101A 0 K 3
9
Loading...