H3C LS-3100-16TP-EI-H3-D-O, LS-3100-26TP-EI-H3-D-O, LS-3100-16TP-PWR-EI-H3, LS-3100-26TP-EI-H3-A-O, LS-3100-26TP-PWR-EI-H3 Installation Manual

H3C S3100 Series Ethernet Switches

Installation Manual

Hangzhou H3C Technologies Co., Ltd.
http://www.h3c.com

Manual Version: 20080115-C-1.04

Copyright © 2007-2008, Hangzhou H3C Technologies Co., Ltd. and its licensors

All Rights Reserved

No part of this manual may be reproduced or transmitted in any form or by any means
without prior written consent of Hangzhou H3C Technologies Co., Ltd.

Trademarks

H3C, , Aolynk, , H3Care,

, TOP G, , IRF, NetPilot,
Neocean, NeoVTL, SecPro, SecPoint, SecEngine, SecPath, Comware, Secware,
Storware, NQA, VVG, V

2

G, VnG, PSPT, XGbus, N-Bus, TiGem, InnoVision and

HUASAN are trademarks of Hangzhou H3C Technologies Co., Ltd.
All other trademarks that may be mentioned in this manual are the property of their

respective owners.

Notice

The information in this document is subject to change without notice. Every effort has
been made in the preparation of this document to ensure accuracy of the content s, but
all statements, information, and recommendations in this document do not constitute
the warranty of any kind, express or implied.

To obtain the latest information, please access:
http://www. h3c.com

Technical Support

[e-mail]
http://www. h3c.com

About This Manual

Related Documentation

In addition to this manual, each H3C S3100 Series Ethernet Switches documentation
set includes the following:

Manual Description

H3C S3100 Series Ethernet Switches
Operation Manual

It is used for assisting the users in data
configurations and typical applications.

H3C S3100 Series Ethernet Switches
Command Manual

It is used for assisting the users in using
various commands.

Organization

H3C S3100 Series Ethernet Switches Installation Manual is organized as follows:

Chapter Contents

1 Product Introduction

Introduces the characteristics and
technical specifications of S3100 Series
Ethernet Switches.

2 Installation Preparation

Introduces the installation preparation
and precaution of S3100 Series
Ethernet Switches.

3 Installation

Introduces the procedures to install an
S3100 Series Ethernet Switch, including
the setup of the mainframe, cards and
cables.

4 First Power-on

Introduces the booting process of an
S3100 Series Ethernet Switch, including
the power-on booting of the switch and
the system initialization.

5 Boot ROM and Host Software Loading

Introduces how to load Boot ROM and
host software for an S3100 Series
Ethernet Switch.

6 Maintenance and Troubleshooting

Introduces the problems that might
occur during the installation and the
booting of an S3100 Series Ethernet
Switch and the related solution.

Chapter Contents

7 Appendix Lightning Protection of the
Switch

Introduces lightning protection of S3100
Series Ethernet Switches.

Conventions

The manual uses the following conventions:

I. GUI conventions

Convention Description

< >

Button names are inside angle brackets. For example, click
<OK>.

[ ]

Window names, menu items, data table and field names
are inside square brackets. For example, pop up the [New
User] window.

/

Multi-level menus are separated by forward slashes. For
example, [File/Create/Folder].

II. Symbols

Convention Description

Warning

Means reader be extremely careful. Improper operation
may cause bodily injury.

Caution

Means reader be careful. Improper operation may cause
data loss or damage to equipment.

 Note Means a complementary description.

Environmental Protection

This product has been designed to comply with the requirements on environmental
protection. For the proper storage, use and disposal of this product, national laws and
regulations must be observed.

Installation Manual
H3C S3100 Series Ethernet Switches Table of Contents

i

Table of Contents

Chapter 1 Product Introduction...................................................................................................1-1

1.1 Overview............................................................................................................................1-1

1.1.1 S3100-SI Series Ethernet Switches........................................................................1-1

1.1.2 S3100-EI Series Ethernet Switches........................................................................1-2

1.2 Introduction to S3100-SI Series Ethernet Switches...........................................................1-3

1.2.1 S3100-26T-SI..........................................................................................................1-3

1.2.2 S3100-16T-SI..........................................................................................................1-4

1.2.3 S3100-8T-SI............................................................................................................1-5

1.2.4 S3100-26C-SI..........................................................................................................1-7

1.2.5 S3100-16C-SI..........................................................................................................1-8

1.2.6 S3100-8C-SI..........................................................................................................1-10

1.3 Introduction to S3100-EI Series Ethernet Switches.........................................................1-11

1.3.1 S3100-26TP-EI......................................................................................................1-11

1.3.2 S3100-16TP-EI......................................................................................................1-13

1.3.3 S3100-8TP-EI........................................................................................................1-14

1.3.4 S3100-26TP-PWR-EI............................................................................................1-16

1.3.5 S3100-16TP-PWR-EI............................................................................................1-18

1.3.6 S3100-8TP-PWR-EI..............................................................................................1-20

1.3.7 S3100-26C-EPON-EI............................................................................................ 1-21

1.3.8 S3100-16C-EPON-EI............................................................................................ 1-23

1.3.9 S3100-8C-EPON-EI.............................................................................................. 1-24

1.4 Introduction to Front Panel LEDs.....................................................................................1-25

1.4.1 Front Panel LEDs of the S3100-SI/S3100-TP-PWR-EI/S3100-C-EPON-EI Series1-25

1.4.2 Front Panel LEDs of the S3100-TP-EI Series.......................................................1-27

1.5 Technical Specifications .................................................................................................. 1-28

1.5.1 S3100-SI Series Ethernet Switch.......................................................................... 1-28

1.5.2 S3100-EI Series Ethernet Switch.......................................................................... 1-31

1.6 SFP Modules Supported by S3100-EI Ethernet Switches ..............................................1-34

1.7 ONU Modules .................................................................................................................. 1-34

Chapter 2 Installation Preparation............................................................................................... 2-1

2.1 Precautions........................................................................................................................2-1

2.2 Requirements on Environment..........................................................................................2-1

2.2.1 Temperature/Humidity Requirements..................................................................... 2-1

2.2.2 Cleanness Requirements........................................................................................2-2

2.2.3 Anti-interference Requirements .............................................................................. 2-3

2.2.4 Laser Usage Security..............................................................................................2-3

2.3 Installation Tools................................................................................................................2-3

Installation Manual
H3C S3100 Series Ethernet Switches Table of Contents

ii

Chapter 3 Installation....................................................................................................................3-1

3.1 Installing a Switch.............................................................................................................. 3-1

3.1.1 Cabinet Mounting.................................................................................................... 3-1

3.1.2 Desk Mounting ...................................................................................................... 3-11

3.1.3 Wall Mounting........................................................................................................3-11

3.1.4 Magnet Mounting...................................................................................................3-13

3.2 Installing an Expansion Interface Module........................................................................3-15

3.3 Connection of Power Cable and Grounding Cable..........................................................3-16

3.3.1 Connecting AC Power Cable ................................................................................ 3-16

3.3.2 Connecting DC Power Cable................................................................................ 3-18

3.3.3 Connecting Grounding Cable................................................................................ 3-21

3.4 Connecting Optical Fiber.................................................................................................3-23

3.5 Connection of Console Cable.......................................................................................... 3-23

3.5.1 Console Cable....................................................................................................... 3-23

3.5.2 Connecting Console Cable ................................................................................... 3-24

3.6 Installation Verification.....................................................................................................3-25

Chapter 4 First Power-on.............................................................................................................. 4-1

4.1 Establishing Configuration Environment............................................................................ 4-1

4.2 Connecting the Console Cable..........................................................................................4-1

4.3 Setting Terminal Parameters.............................................................................................4-1

4.4 Booting Switch................................................................................................................... 4-4

4.4.1 Checking Before Powering on the Switch...............................................................4-4

4.4.2 Powering on the Switch........................................................................................... 4-4

4.4.3 Changing the Startup Mode.................................................................................... 4-6

Chapter 5 Boot ROM and Host Software Loading ..................................................................... 5-1

5.1 Introduction to Loading Approaches..................................................................................5-1

5.2 Local Software Loading.....................................................................................................5-1

5.2.1 Boot Menu...............................................................................................................5-2

5.2.2 Loading Software Using XModem Through Console Port......................................5-3

5.2.3 Loading Software Using TFTP Through Ethernet Port........................................... 5-8

5.2.4 Loading Software Using FTP Through Ethernet Port............................................. 5-9

5.3 Remote Software Loading...............................................................................................5-11

5.3.1 Remote Loading Using FTP..................................................................................5-11

5.3.2 Remote Loading Using TFTP................................................................................5-13

Chapter 6 Maintenance and Troubleshooting............................................................................ 6-1

6.1 Software Loading Failure................................................................................................... 6-1

6.2 Missing Password..............................................................................................................6-1

6.2.1 Missing user password............................................................................................ 6-1

6.2.2 Missing Boot ROM Password ................................................................................. 6-2

6.3 Power System Failure........................................................................................................ 6-2

6.4 Configuration System Failure ............................................................................................ 6-2

Installation Manual
H3C S3100 Series Ethernet Switches Table of Contents

iii

Installation Manual
H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction

1-1

Chapter 1 Product Introduction

1.1 Overview

The H3C S3100 Series Ethernet Switches are high-performance, high-density,
easy-to-install, NMS-manageable intelligent Ethernet switches which support
wire-speed Layer 2 switching.

Table 1-1 lists the models of the H3C S3100 Series Ethernet Switches.

Table 1-1 Models of the H3C S3100 Series Ethernet Switches

Name Subseries Model

S3100-C-SI

z S3100-8C-SI
z S3100-16C-SI
z S3100-26C-SI

S3100-SI

S3100-T-SI

z S3100-8T-SI
z S3100-16T-SI
z S3100-26T-SI

S3100-TP-EI

z S3100-8TP-EI
z S3100-16TP-EI
z S3100-26TP-EI

S3100-TP-PWR-EI

z S3100-8TP-PWR-EI
z S3100-16TP-PWR-EI
z S3100-26TP-PWR-EI

H3C S3100
Series
Ethernet
Switches

S3100-EI

S3100-C-EPON-EI

z S3100-8C-EPON-EI
z S3100-16C-EPON-EI
z S3100-26C-EPON-EI

1.1.1 S3100-SI Series Ethernet Switches

Currently, the S3100-SI Series Ethernet Switches include the S3100-T-SI and the
S3100-C-SI, as listed in

Table 1-2 and Table 1-3.

Table 1-2 H3C S3100-T-SI Series Ethernet Switches

Model

Power

input

Number of

10/100 Mbps

electrical ports

Number of

gigabit uplink

ports

Number of

console

ports

S3100-26T-SI 24 Two Ethernet ports
S3100-16T-SI 16
S3100-8T-SI

AC

8

One Ethernet port

1

Installation Manual
H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction

1-2

Table 1-3 H3C S3100-C-SI Series Ethernet Switches

Model Power input

Number of

10/100 Mbps

electrical ports

Number of
expansion

slots

Number of

console

ports

S3100-26C-SI 24 2
S3100-16C-SI 16 2

S3100-8C-SI

AC input for
AC-powered
switches.

DC input for
DC-powered
switches

8 1

1

1.1.2 S3100-EI Series Ethernet Switches

Currently, the H3C S3100-EI Series Ethernet Switches include the S3100-TP-EI, the
S3100-TP-PWR-EI and the S3100-C-EPON-EI, as listed in

Table 1-4 and Table 1-5.

Table 1-4 Models of the H3C S3100-TP-EI and S3100-TP-PWR-EI Series Ethernet
Switches

Model Power input

Number of

10/100 Mbps

electrical

ports

Number of 1000

Mbps uplink

ports

Number of

console

ports

S3100-26TP­EI

24

Two Combo
ports

1

S3100-16TP­EI

16

Two Combo
ports

1

S3100-8TP-EI

AC input for
AC-powered
switches

DC input for
DC-powered
switches

8 One Combo port 1

S3100-26TP­PWR-EI

AC or RPS DC
input

24

Two Combo
ports

1

S3100-16TP­PWR-EI

16

Two Combo
ports

1

S3100-8TP-P
WR-EI

AC input

8 One Combo port 1

Installation Manual
H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction

1-3

Table 1-5 Models of the H3C S3100-C-EPON-EI Series Ethernet Switches

Model

Power

input

Number

of 10/100

Mbps

electrical

ports

Number of
1000 Mbps

uplink

PON ports

Number of
expansion

slots

Number

of

console

ports

S3100-26C-EPON-EI 24 1 1
S3100-16C-EPON-EI 16 1 Disabled
S3100-8C-EPON-EI

AC
input

8 1 —

1

1.2 Introduction to S3100-SI Series Ethernet Switches

1.2.1 S3100-26T-SI

I. Front panel

S3100-26T-SI Ethernet switches each provide twenty-four auto-sensing
10/100Base-TX Ethernet ports, two 10/100/1000Base-T Ethernet ports, and one
console port.

Figure 1-1 shows the front panel of an S3100-26T-SI Ethernet switch.

(1) Power LED (2) A/L LED
(3) D/S LED (4) Port status LED, left (yellow)
(5) Port status LED, right (green) (6) 10/100 Base-TX port
(7) 10/100/1000 Base-T port (8) Console port
(9) LINK LED (green) (10) ACT LED (yellow)
(11) Mode button

Figure 1-1 Front panel of an S3100-26T-SI Ethernet switch

 Note:

For details about LEDs on the front panel, refer to section 1.4.1 “Front Panel LEDs of
the S3100-SI/S3100-TP-PWR-EI/S3100-C-EPON-EI Series”.

Installation Manual
H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction

1-4

II. Rear panel

Figure 1-2 shows the rear panel of an S3100-26T-SI Ethernet switch.

(1) AC power socket (2) Grounding screw

Figure 1-2 Rear panel of an S3100-26T-SI Ethernet switch

III. Power system

S3100-26T-SI Ethernet switches support AC input.

z Rated voltage range: 100 VAC to 240 VAC, 50 Hz/60 Hz
z Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz

IV. Cooling system

The S3100-26T-SI cools off naturally.

1.2.2 S3100-16T-SI

I. Front panel

S3100-16T-SI Ethernet switches each provide sixteen auto-sensing 10/100Base-TX
Ethernet ports, one 10/100/1000Base-T Ethernet port, and one console port.

Figure 1-3 shows the front panel of an S3100-16T-SI Ethernet switch.

(1) Power LED (2) A/L LED
(3) D/S LED (4) Port status LED, left (yellow)
(5) Port status LED, right (green) (6) 10/100 Base-TX port
(7) 10/100/1000 Base-T port (8) Console port
(9) LINK LED (green) (10) ACT LED (yellow)
(11) Mode button

Figure 1-3 Front panel of an S3100-16T-SI Ethernet switch

Installation Manual
H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction

1-5

 Note:

For details about LEDs on the front panel, refer to section 1.4.1 “Front Panel LEDs of
the S3100-SI/S3100-TP-PWR-EI/S3100-C-EPON-EI Series”.

II. Rear panel

Figure 1-4 shows the rear panel of an S3100-16T-SI Ethernet switch.

(1) AC power socket (2) Grounding screw

Figure 1-4 Rear panel of an S3100-16T-SI Ethernet switch

III. Power system

S3100-16T-SI Ethernet switches support AC input.

z Rated voltage range: 100 VAC to 240 VAC, 50 Hz/60 Hz
z Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz

IV. Cooling system

The S3100-16T-SI cools off naturally.

1.2.3 S3100-8T-SI

I. Front panel

S3100-8T-SI Ethernet switches each provide eight auto-sensing 10/100Base-TX
Ethernet ports, one 10/100/1000Base-T Ethernet port, and one console port.

Figure 1-5 shows the front panel of an S3100-8T-SI Ethernet switch.

Installation Manual
H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction

1-6

(1) Power LED (2) A/L LED
(3) D/S LED (4) Port status LED, left (yellow)
(5) Port status LED, right (green) (6) 10/100 Base-TX port
(7) 10/100/1000 Base-T port (8) Console port
(9) LINK LED (green) (10) ACT LED (yellow)
(11) Mode button

Figure 1-5 Front panel of an S3100-8T-SI Ethernet switch

 Note:

For details about LEDs on the front panel, refer to section 1.4.1 “Front Panel LEDs of
the S3100-SI/S3100-TP-PWR-EI/S3100-C-EPON-EI Series”.

II. Rear panel

Figure 1-6 shows the rear panel of an S3100-8T-SI Ethernet switch.

(1) AC power socket (2) Grounding screw

Figure 1-6 Rear panel of an S3100-8T-SI Ethernet switch

III. Power system

S3100-8T-SI Ethernet switches support AC input.

z Rated voltage range: 100 VAC to 240 VAC, 50 Hz/60 Hz
z Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz

IV. Cooling system

The S3100-8T-SI cools off naturally.

Installation Manual
H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction

1-7

1.2.4 S3100-26C-SI

Both AC-powered switches and DC-po wered switches are available to this model.

I. Front panel

S3100-26C-SI Ethernet switches each provide twenty-four auto-sensing
10/100Base-TX Ethernet ports, two expansion slot s, and one console port.

S3100-26C-SI Ethernet switches have the same front panel, as shown in

Figure 1-7.

(1) Power LED (2) A/L LED
(3) D/S LED (4) Port status LED, left (yellow)
(5) Port status LED, right (green) (6) 10/100Base- TX port
(7) Expansion slot (8) Console port
(9) Mode button

Figure 1-7 Front panel of an S3100-26C-SI Ethernet switch

 Note:

z With a PoE card inserted in one expansion slot, an S3100-26C-SI Ethernet switch

will be a powered device (PD). In this case, the other expansion slot becomes
unavailable.

z For details about LEDs on the front panel, refer to section 1.4.1 “Front Panel LEDs

of the S3100-SI/S3100-TP-PWR-EI/S3100-C-EPON-EI Series”.

II. Rear panel

Figure 1-8 shows the rear panel of an S3100-26C-SI AC-powered Ethernet switch.

(1) AC power socket (2) Grounding screw

Figure 1-8 Rear panel of an S3100-26C-SI AC-powered Ethernet switch

Installation Manual
H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction

1-8

Figure 1-9 shows the rear panel of an S3100-26C-SI DC-powered Ethernet switch.

(1) DC input terminal block (2) Grounding screw

Figure 1-9 Rear panel of an S3100-26C-SI DC-powered Ethernet switch

III. Power system

1) S3100-26C-SI AC-powered Ethernet switches:

z Rated voltage range: 100 VAC to 240 VAC, 50 Hz/60 Hz
z Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz

2) S3100-26C-SI DC-powered Ethernet switches:

z Rated voltage range: –48 VDC to –60 VDC
z Input voltage range: –36 VDC to –72 VDC

IV. Cooling system

The S3100-26C-SI cools off naturally.

1.2.5 S3100-16C-SI

Both AC-powered switches and DC-po wered switches are available to this model.

I. Front panel

S3100-16C-SI Ethernet switches each provide sixteen auto-sensing 10/100Base-TX
Ethernet ports, two expansion slots, and one co nsole port.

S3100-16C-SI Ethernet switches have the same front panel, as shown in

Figure 1-10.

(1) Power LED (2) A/L LED
(3) D/S LED (4) Port status LED, left (yellow)
(5) Port status LED, right (green) (6) 10/100Base- TX port
(7) Expansion slot (8) Console port
(9) Mode button

Figure 1-10 Front panel of an S3100-16C-SI Ethernet switch

Installation Manual
H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction

1-9

 Note:

z With a PoE card inserted in one expansion slot, an S3100-16C-SI Ethernet switch

will be a powered device (PD). In this case, the other expansion slot becomes
unavailable.

z For details about LEDs on the front panel, refer to section 1.4.1 “Front Panel LEDs

of the S3100-SI/S3100-TP-PWR-EI/S3100-C-EPON-EI Series”.

II. Rear panel

Figure 1-1 1 shows the rear panel of an S3100-16C-SI AC-powered Ethernet switch.

(1) AC power socket (2) Grounding screw

Figure 1-11 Rear panel of an S3100-16C-SI AC-powered Ethernet switch

Figure 1-12 shows the rear panel of an S3100-16C-SI DC-powered Ethernet switch.

(1) DC input terminal block (2) Grounding screw

Figure 1-12 Rear panel of an S3100-16C-SI DC-powered Ethernet switch

III. Power system

1) S3100-16C-SI AC-powered Ethernet switches:

z Rated voltage range: 100 VAC to 240 VAC, 50 Hz/60 Hz
z Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz

2) S3100-16C-SI DC-powered Ethernet switches:

z Rated voltage range: –48 VDC to –60 VDC
z Input voltage range: –36 VDC to –72 VDC

IV. Cooling system

The S3100-16C-SI cools off naturally.

Installation Manual
H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction

1-10

1.2.6 S3100-8C-SI

Both AC-powered switches and DC-po wered switches are available to this model.

I. Front panel

S3100-8C-SI Ethernet switches each provide eight auto-sensing 10/100Base-TX
Ethernet ports, one expansion slot, and one console port.

S3100-8C-SI Ethernet switches have the same front panel, as shown in

Figure 1-13.

(1) Power LED (2) A/L LED
(3) D/S LED (4) Port status LED, left (yellow)
(5) Port status LED, right (green) (6) 10/100Base- TX port
(7) Expansion slot (8) Console port
(9) Mode button

Figure 1-13 Front panel of an S3100-8C-SI Ethernet switch

 Note:

For details about LEDs on the front panel, refer to section 1.4.1 “Front Panel LEDs of
the S3100-SI/S3100-TP-PWR-EI/S3100-C-EPON-EI Series”.

II. Rear panel

Figure 1-14 shows the rear panel of an S3100-8C-SI AC-powered Ethernet switch.

(1) AC power socket (2) Grounding screw

Figure 1-14 Rear panel of an S3100-8C-SI AC-powered Ethernet switch

Installation Manual
H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction

1-11

Figure 1-15 shows the rear panel of an S3100-8C-SI DC-powered Ethernet switch.

(1) DC input terminal block (2) Grounding screw

Figure 1-15 Rear panel of an S3100-8C-SI DC-powered Ethernet switch

III. Power system

1) S3100-8C-SI AC-powered Ethernet switches:

z Rated voltage range: 100 VAC to 240 VAC, 50 Hz/60 Hz
z Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz

2) S3100-8C-SI DC-powered Ethernet switches:

z Rated voltage range: –48 VDC to –60 VDC
z Input voltage range: –36 VDC to –72 VDC

IV. Cooling system

The S3100-8C-SI cools off naturally.

1.3 Introduction to S3100-EI Series Ethernet Switches

1.3.1 S3100-26TP-EI

Both AC-powered switches and DC-po wered switches are available to this model.

I. Front panel

S3100-26TP-EI Ethernet switches each provide twenty-four auto-sensing
10/100Base-TX Ethernet ports, two auto-sensing 10/100/1000Base-T Ethernet ports,
two 100/1000Base-X SFP ports, and one console port. Each SFP port and the
corresponding auto-sensing 10/100/1000Base- T Ethern et port form a Combo port. For
each Combo port, either the SFP port or the corresponding 10/100/1000Base- T
Ethernet port can be used at a time.

S3100-26TP-EI Ethernet switches have the same front panel, as shown in

Figure 1-16.

Installation Manual
H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction

1-12

(1) (2) (4)

(5)

(6)

(7)(8)

(3)

(7)

(1) Auto-sensing 10/100Base-TX port Speed LED (green)
(2) Auto-sensing 10/100Base-TX port (3) Combo port Speed LED (green)
(4) Auto-sensing 10/100/1000Base-T port (5) Console port
(6) 100/1000Base-X SFP port (7) LINK/ACT LED (green)
(8) Power LED (PWR)

Figure 1-16 Front panel of an S3100-26TP-EI Ethernet switch

 Note:

For details about LEDs on the front panel, refer to section 1.4.2 Front Panel LEDs of
the S3100-TP-EI Series .

II. Rear panel

Figure 1-17 shows the rear panel of an S3100-26TP-EI AC-powered Ethernet switch.

(1) (2)

(1) Grounding screw (2) AC input terminal block

Figure 1-17 Rear panel of an S3100-26TP-EI AC-powered Ethernet switch

Figure 1-18 shows the rear panel of an S3100-26TP-EI DC-powered Ethernet switch.

(1) (2)

(1) Grounding screw (2) DC input terminal block

Figure 1-18 Rear panel of an S3100-26TP-EI DC-powered Ethernet switch

III. Power system

1) S3100-26TP-EI AC-powered Ethernet switches:

Installation Manual
H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction

1-13

z Rated voltage range: 100 VAC to 240 VAC, 50 Hz/60 Hz
z Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz

2) S3100-26TP-EI DC-powered Ethernet switches:

z Rated voltage range: –48 VDC to –60 VDC
z Input voltage range: –36 VDC to –72 VDC

IV. Cooling system

The S3100-26TP-EI cools off naturally.

1.3.2 S3100-16TP-EI

Both AC-powered switches and DC-po wered switches are available to this model.

I. Front panel

S3100-16TP-EI Ethernet switches each provide sixteen auto-sensing 10/100Base-TX
Ethernet ports, two auto-sensing 10/100/1000Base-T Ethernet ports, two
100/1000Base-X SFP ports, and one console port. Each SFP port and the
corresponding auto-sensing 10/100/1000Base- T Ethern et port form a Combo port. For
each Combo port, either the SFP port or the corresponding 10/100/1000Base- T
Ethernet port can be used at a time.

S3100-16TP-EI Ethernet switches have the same front panel, as shown in

Figure 1-19.

(

1)(

2

)

(4)

(5)

(6)

(7)

(8)

(3)

(7)

(1) Auto-sensing 10/100Base-TX port Speed LED (green)
(2) Auto-sensing 10/100Base-TX port (3) Combo port Speed LED (green)
(4) Auto-sensing 10/100/1000Base-T port (5) Console port
(6) 100/1000Base-X SFP port (7) LINK/ACT LED (green)
(8) Power LED (PWR)

Figure 1-19 Front panel of an S3100-16TP-EI Ethernet switch

 Note:

For details about LEDs on the front panel, refer to section 1.4.2 Front Panel LEDs of
the S3100-TP-EI Series

Installation Manual
H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction

1-14

II. Rear panel

Figure 1-20 shows the rear panel of an S3100-16TP-EI AC-powered Ethernet switch.

(1) (2)

(1) Grounding screw (2) AC input terminal block

Figure 1-20 Rear panel of an S3100-16TP-EI AC-powered Ethernet switch

Figure 1-21 shows the rear panel of an S3100-16TP-EI DC-powered Ethernet switch.

(1) (2)

(1) Grounding screw (2) DC input terminal block

Figure 1-21 Rear panel of an S3100-16TP-EI DC-powered Ethernet switch

III. Power system

1) S3100-16TP-EI AC-powered Ethernet switches:

z Rated voltage range: 100 VAC to 240 VAC, 50 Hz/60 Hz
z Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz

2) S3100-16TP-EI DC-powered Ethernet switches:

z Rated voltage range: –48 VDC to –60 VDC
z Input voltage range: –36 VDC to –72 VDC

IV. Cooling system

The S3100-16TP-EI cools off naturally.

1.3.3 S3100-8TP-EI

Both AC-powered switches and DC-po wered switches are available to this model.

I. Front panel

S3100-8TP-EI Ethernet switches each provide eight auto-sensing 10/100Base-TX
Ethernet ports, one auto-sensing 10/100/1000Base-T Ethernet ports, one
100/1000Base-X SFP ports, and one console po rt. The SFP port an d the auto-sensing
10/100/1000Base- T Ethernet port form a Combo port. For the Combo port, either the
SFP port or the 10/100/1000Base- T Ethernet port can be u sed at a time.

Installation Manual
H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction

1-15

S3100-8TP-EI Ethernet switches have the same front panel, as shown in Figure 1-22.

(1) (2) (4)

(5)

(6)(7)(8)

(3)

(7)

(1) Auto-sensing 10/100Base-TX port Speed LED (green)
(2) Auto-sensing 10/100Base-TX port (3) Combo port Speed LED (green)
(4) Auto-sensing 10/100/1000Base-T port (5) Console port
(6) 100/1000Base-X SFP port (7) LINK/ACT LED (green)
(8) Power LED (PWR)

Figure 1-22 Front panel of an S3100-8TP-EI Ethernet switch

 Note:

For details about LEDs on the front panel, refer to section 1.4.2 Front Panel LEDs of
the S3100-TP-EI Series .

II. Rear panel

Figure 1-23 shows the rear panel of an S3100-8TP-EI AC-powered Ethernet switch.

(1) (2)

(1) Grounding screw (2) AC input terminal block

Figure 1-23 Rear panel of an S3100-8TP-EI AC-powered Ethernet switch

Figure 1-24 shows the rear panel of an S3100-8TP-EI DC-powered Ethernet switch.

Installation Manual
H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction

1-16

(1) (2)

(1) Grounding screw (2) DC input terminal block

Figure 1-24 Rear panel of an S3100-8TP-EI DC-powered Ethernet switch

III. Power system

1) S3100-8TP-EI AC-powered Ethernet switches:

z Rated voltage range: 100 VAC to 240 VAC, 50 Hz/60 Hz
z Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz

2) S3100-8TP-EI DC-powered Ethernet switches:

z Rated voltage range: –48 VDC to –60 VDC
z Input voltage range: –36 VDC to –72 VDC

IV. Cooling system

The S3100-8TP-EI cools off naturally.

1.3.4 S3100-26TP-PWR-EI

I. Front panel

S3100-26TP-PWR-EI Ethernet switches each provide twenty-four auto-sensing
10/100Base-TX Ethernet ports, two 10/100/1000Base-T Ethernet ports, two
100/1000Base SFP ports, and one console port. Each SFP port and the corresponding
10/100/1000Base- T Ethernet port form a Combo port. For each Combo po rt, either the
SFP port or the corresponding 10/100/1000Base- T Ethernet port can be used at a
time.

Figure 1-25 shows the front panel of an S3100-26TP-PWR-EI Ethernet switch.

Installation Manual
H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction

1-17

(1) (2) (3) (4)

(5)(6)(7)(8)

(1) Auto-sensing 10/100Base-TX Ethernet port status LED
(2) LINK LED for Combo port (3) Console port
(4) Power LED (PWR) (5) A/L LED
(6) D/S LED (7) Mode button
(8) ACT LED for Combo port

Figure 1-25 Front panel of an S3100-26TP-PWR-EI Ethernet switch

 Note:

For details about LEDs on the front panel, refer to section 1.4.1 “Front Panel LEDs of
the S3100-SI/S3100-TP-PWR-EI/S3100-C-EPON-EI Series”.

II. Rear panel

(1) (2) (3)

(1) AC power socket (2) DC power socket
(3) Grounding screw

Figure 1-26 Rear panel of an S3100-26TP-PWR-EI Ethernet switch

III. Power system

S3100-26TP-PWR-EI Ethernet switches support AC input or DC input.

1) AC input

z Rated voltage range: 100 VAC to 240 VAC, 50 Hz/60 Hz
z Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz

2) DC input

z Rated voltage range: –52 VDC to –56 VDC

Installation Manual
H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction

1-18

 Note:

Only the recommended RPS can be used for S3100-26TP-PWR-EI Ethernet switches.
The –48 VDC in the equipment room cannot be used directly. Otherwise, the device
may be damaged.

IV. Cooling system

The S3100-26TP-PWR-EI has four fans for heat dissipation.

1.3.5 S3100-16TP-PWR-EI

I. Front panel

S3100-16TP-PWR-EI Ethernet switches each provide sixteen auto-sensing
10/100Base-TX Ethernet ports, two 10/100/1000Base-T Ethernet ports, two
100/1000Base SFP ports, and one console port. Each SFP port and the corresponding
10/100/1000Base-T Ethernet port form a Combo port. For each Co mbo port, either the
SFP port or the corresponding 10/100/1000Base-T Ethernet port can be used at a time.

Figure 1-27 shows the front panel of an S3100-16TP-PWR-EI Ethernet switch.

(1) (2) (3) (4)

(5)(6)(7)(8)

(1) Auto-sensing 10/100Base-TX Ethernet port status LED
(2) LINK LED for Combo port (3) Console port
(4) Power LED (PWR) (5) A/L LED
(6) D/S LED (7) Mode button
(8) ACT LED for Combo port

Figure 1-27 Front panel of an S3100-16TP-PWR-EI Ethernet switch

Installation Manual
H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction

1-19

 Note:

For details about LEDs on the front panel, refer to section 1.4.1 “Front Panel LEDs of
the S3100-SI/S3100-TP-PWR-EI/S3100-C-EPON-EI Series”.

II. Rear panel

(1) (2)

(1) AC power socket (2) Grounding screw

Figure 1-28 Rear panel of an S3100-16TP-PWR-EI Ethernet switch

III. Side panel

Each S3100-16TP-PWR-EI Ethernet switch provides a security slot, through whi ch you
can lock the device together with an irremovable object to prevent theft.

The security slot is located at the rear end of the left side panel, as shown in

Figure

1-29.

(1)

(1) Security slot

Figure 1-29 Security slot on left side panel of an S3100-16TP-PWR-EI Ethernet switch

 Note:

If the left screw hole above the security slot is used, the security slot cannot be used.

Installation Manual
H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction

1-20

IV. Power system

S3100-16TP-PWR-EI Ethernet switches support AC input.

z Rate voltage range: 100 VAC to 240 VAC, 50 Hz/60 Hz
z Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz

V. Cooling system

The S3100-16TP-PWR-EI has two fans for heat dissipation.

1.3.6 S3100-8TP-PWR-EI

I. Front panel

S3100-8TP-PWR-EI Ethernet switches each provide eight auto-sensing
10/100Base-TX Ethernet ports, one 10/100/1000Base-T Ethernet port, one
100/1000Base SFP ports, and one console port. The SFP port and the
10/100/1000Base-T Ethernet port form a Combo port. Either the SFP port or the
10/100/1000Base-T Ethernet port can be used at a time.

Figure 1-30 shows the front panel of an S3100-8TP-PWR-EI Ethernet switch.

(1) (2) (3) (4)

(5)(6)(7)(8)

(1) Auto-sensing 10/100Base-TX Ethernet port status LED
(2) LINK LED for Combo port (3) Console port
(4) Power LED (PWR) (5) A/L LED
(6) D/S LED (7) Mode button
(8) ACT LED for Combo port

Figure 1-30 Front panel of an S3100-8TP-PWR-EI Ethernet switch

 Note:

For details about LEDs on the front panel, refer to section 1.4.1 “Front Panel LEDs of
the S3100-SI/S3100-TP-PWR-EI/S3100-C-EPON-EI Series”.

Installation Manual
H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction

1-21

II. Rear panel

(1) (2)

(1) AC power socket (2) Grounding screw

Figure 1-31 Rear panel of an S3100-8TP-PWR-EI Ethernet switch

III. Side panel

Each S3100-8TP-PWR-EI Ethernet switch provides a security slot, through which you
can lock the device together with an irremovable object to prevent theft.

The security slot is located at the rear end of the left side panel, as shown in

Figure

1-29.

 Note:

If the left screw hole above the security slot is used, the security slot cannot be used.

IV. Power system

S3100-8TP-PWR-EI Ethernet switches support AC input.

z Rate voltage range: 100 VAC to 240 VAC, 50 Hz/60 Hz
z Input voltage range: 90 VAC to 264 VAC, 47 HZ to 63 Hz

V. Cooling system

The S3100-8TP-PWR-EI has two fans for heat dissipation.

1.3.7 S3100-26C-EPON-EI

I. Front panel

The S3100-26C-EPON-EI provides 24 x 10/100Base-TX ports, one Gigabit uplink PON
port, one expansion slot, and one console port.

Figure 1-32 shows the front view of the S3100-26C-EPON-EI.

Installation Manual
H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction

1-22

(1): Power Led (PWR) (2): A/L LED
(3): D/S LED (4): Port status LED, left (yellow)
(5): Port status LED, right (green) (6): 10/100 Base-TX port
(7): ONU module (8): Console port
(9): LINK LED for the uplink PON port (10): ACT LED for the uplink PON port
(11): 1000 Mbps uplink PON port (12): Expansion slot
(13): MODE button

Figure 1-32 Front panel of the S3100-26C-EPON-EI

 Note:

z The S3100-26C-EPON-EI provides one expansion slot. You can order one mo re

ONU module (1000Base- PX20) as needed. For more information about ONU
modules, refer to section

1.7 “ONU Modules”.

z For details about the LEDs on the front panel, refer to section 1.4.1 “Front Panel

LEDs of the S3100-SI/S3100-TP-PWR-EI/S3100-C-EPON-EI Series”.

II. Rear panel

(1) AC power socket (2) Grounding screw

Figure 1-33 Rear panel of an S3100-26C-EPON-EI Ethernet switch

III. Power system

S3100-26C-EPON-EI Ethernet switches support AC input.

z Rated voltage range: 100 VAC to 240 VAC, 50 Hz/60 Hz
z Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz

IV. Cooling system

The S3100-26C-EPON-EI has one fan for heat dissipation.

Installation Manual
H3C S3100 Series Ethernet Switches Chapter 1 Product Introduction

1-23

1.3.8 S3100-16C-EPON-EI

I. Front panel

The S3100-16C-EPON-EI provides 16 x 10/100Base-TX Ethernet ports, one 1000
Mbps uplink PON port, and one console port.

Figure 1-34 shows the front panel of the S3100-16C-EPON-EI.

(1): Power Led (PWR) (2): A/L LED
(3): D/S LED (4): Port status LED, left (yellow)
(5): Port status LED, right (green) (6): 10/100 Base-TX port
(7): ONU module (8): Console port
(9): LINK LED for the uplink PON port (10): ACT LED for the uplink PON port
(11): 1000 Mbps uplink PON port (12): Expansion slot (disabled)
(13): MODE button

Figure 1-34 Front panel of the S3100-16C-EPON-EI

 Note:

z The S3100-16C-EPON-EI supports only one ONU module (required).
z For details about the LEDs on the front panel, refer to section 1.4.1 “Front Panel

LEDs of the S3100-SI/S3100-TP-PWR-EI/S3100-C-EPON-EI Series”.

II. Rear panel

(1) AC power socket (2) Grounding screw

Figure 1-35 Rear panel of an S3100-16C-EPON-EI Ethernet switch

III. Power system

S3100-16C-EPON-EI Ethernet switches support AC input.

z Rated voltage range: 100 VAC to 240 VAC, 50 Hz/60 Hz
z Input voltage range: 90 VAC to 264 VAC, 47 Hz to 63 Hz