H3C AR 18-2 Series, AR 18-21, AR 18-22-8, AR 18-22S-8, AR 18-23S-1 Installation Manual
...
H3C AR 18-2X Series Routers
Installation Manual
Hangzhou H3C Technologies Co., Ltd.
http://www.h3c.com
Manual Version: T2-08045E-20070423-C-1.02
Copyright © 2006-2007, Hangzhou H3C Technologies Co.,
Ltd. and its licensors
All Rights Reserved
No part of this manual may be reproduced or transmitted in any form
or by any means without prior written consent of Hangzhou H3C
Technologies Co., Ltd.
Trademarks
H3C, , Aolynk, , H3Care,
, TOP G, , IRF,
NetPilot, Neocean, NeoVTL, SecPro, SecPoint, SecEngine, SecPath,
Comware, Secware, Storware, NQA, VVG, V
2
G, VnG, PSPT, XGbus,
N-Bus, TiGem, InnoVision and HUASAN are trademarks of Hangzhou
H3C Technologies Co., Ltd.
All other trademarks that may be mentioned in this manual are the
property of their respective owners.
Notice
The information in this document is subject to change without notice.
Every effort has been made in the preparation of this document to
ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute the warranty of
any kind, express or implied.
To obtain the latest information, please access:
http://www.h3c.com
Technical Support
customer_service@h3c.com
http://www.h3c.com
About This Manual
Related Documentation
In addition to this manual, each AR 18-2X Series Routers
documentation set includes the following:
Manual Content
Comware V3 Operation Manual
The manual is a guide for the
user to perform the operations
correctly. It is organized into the
parts of getting started, system
management, interface, link
layer protocol, network protocol,
routing protocol, multicast
protocol, security, VPN,
reliability, QoS, MPLS, dial-up
and Non-IP Architecture, as well
as acronyms used in the
manual.
Comware V3 Command Manual
The manual gives the user a
detailed description of the
operating commands. It is
organized into the parts of
getting started, system
management, interface, link
layer protocol, network protocol,
routing protocol, multicast
protocol, security, VPN,
reliability, QoS, MPLS, dial-up
and Non-IP Architecture, as well
as a command index.
Manual Content
Low-End and Mid-Range Series
Routers Terminal Access U ser
Manual
This manual covers all interface
cards and modules available
with H3C AR Series Routers,
including the cable pinouts,
function, interface attribute,
panels and LEDs.
LMR Series Routers Cable
Manual
This manual introduces all cable
pinouts available with LMR
series routers.
Organization
H3C AR 18-2X Series Routers Installation Manual is organized
as follows:
Chapter Contents
1 Product Overview
Hardware Features of H3C AR 18-2X
Series Routers
2 Installing the Router
Introduces the installation
requirements, the issues needed to
be considered and the installation
tools needed for the installation of the
AR 18-2X Series Routers.
3. Starting and Maintaining
the Router
Covers the configuration and
software maintenance of the H3C AR
18-2X Series Routers, including
software upgrade and the application
program upgrade.
4. Troubleshooting
Lists the problems and checkup
methods when H3C AR 18-2X Series
Routers are installed.
Conventions
The manual uses the following conventions:
I.
Command conventions
Convention Description
Boldface
The keywords of a command line are in
Boldface.
italic
Command arguments are in italic.
[ ]
Items (keywords or arguments) in square
brackets [ ] are optional.
{ x | y | ... }
Alternative items are grouped in braces
and separated by vertical bars. One is
selected.
[ x | y | ... ]
Optional alternative items are grouped in
square brackets and separated by vertical
bars. One or none is selected.
{ x | y | ... } *
Alternative items are grouped in braces
and separated by vertical bars. A minimum
of one or a maximum of all can be selected.
[ x | y | ... ] *
Optional alternative items are grouped in
square brackets and separated by vertical
bars. Many or none can be selected.
&<1-n>
The argument(s) before the ampersand (&)
sign can be entered 1 to n times.
# A line starting with the # sign is comments.
GUI conventions II.
Convention Description
< >
Button names are inside angle brackets.
For example, click <OK>.
[ ]
Window names, menu items, data table
and field names are inside square
brackets. For example, pop up the [New
User] window.
/
Multi-level menus are separated by forward
slashes. For example, [File/Create/Folder].
Symbols
III.
Convention Description
Warning
Means reader be extremely careful.
Improper operation may cause bodily
injury.
Caution
Means reader be careful. Improper
operation may cause data loss or damage
to equipment.
Note Means a complementary description.
Environmental Protection
This product has been designed to com ply with the requirement s
on environmental protection. For the proper storage, use and di sposal
of this product, national laws and regulations must be observed.
Installation Manual
H3C AR 18-2X Series Routers
Table of Contents
i
Table of Contents
Chapter 1 Product Overview ........................................................1-1
1.1 Introduction ........................................................................1-1
1.2 Hardware Features of the AR 18-2X..................................1-2
1.2.1 Hardware Features of the AR 18-21.......................1-2
1.2.2 Hardware Features of the AR 18-22.......................1-6
1.2.3 Hardware Features of the AR 18-22-8/18-2 2S-8....1-9
1.2.4 Hardware Features of the AR 18-23-1/18-2 3S-1..1-12
Installation Manual
H3C AR 18-2X Series Routers
Chapter 1 Product Overvie
w
1-1
Chapter 1 Product Overview
1.1 Introduction
H3C AR 18-2X Series Routers (hereinafter referred to as the AR
18-2X series) are Ethernet access routers designed for small office
home office (SOHO) subscribers. By far, the series have six models:
AR 18-21/18-22/18-22-8/18-22S-8/18-23-1/18-23S-1. They provide
an uplink Ethernet interface and four downlink layer 2 (L2) switched
10/100BASE-T Ethernet interfaces that can be isolated.
The AR 18-2X series support multiple virtual private network
(VPN) services, such as layer 2 tunneling protocol (L2TP) VPN, IP
security (IPSec) VPN, generic routing encap sulatio n (G RE) VPN, and
dynamic VPN (DVPN). They can provide tunnel connections to remote
users to build VPNs that can be internets, intranets, or access
networks.
The series support firewall, AAA (authentication, authorization,
accounting), network address translation (NAT), and quality of service
(QoS). Therefore, they can ensure security and guaranteed services
to the private networks constructed on the open Internet.
In the series the AR 18-22S-8 and AR 18-23S-1 has a build-in
hardware encryption chip, which can significantly improve encryption
performance.
The interfaces that the AR 18-2X series provide are compliant
with the international standards and can work with the products of
other vendors at every layer. The existing investment of users can
thus be protected to the maximum.
Installation Manual
H3C AR 18-2X Series Routers
Chapter 1 Product Overvie
w
1-2
1.2 Hardware Features of the AR 18-2X
1.2.1 Hardware Features of the AR 18-21
I. Appearance
1) Ethernet LED LAN4 2) Ethernet LED LAN3
3) Ethernet LED LAN2 4) Ethernet LED LAN1
5) WAN LED (WAN0) 6) SYSTEM LED (SYS)
7) POWER LED (PWR)
Figure 1-1 Front view of the AR 18-21
1) Power switch 2) Power socket
3) Console port (CONSOLE) 4) Ethernet interface 1 (LAN1)
5) Ethernet interface 2(LAN2) 6) Ethernet interface 3 (LAN3)
7) Ethernet interface 4 (LAN4) 8) Grounding screw
9) WAN interface (WAN0)
Figure 1-2 Rear view of the AR 18-21
Installation Manual
H3C AR 18-2X Series Routers
Chapter 1 Product Overvie
w
1-3
II. System specifications
Table 1-1 System specifications of the AR 18-21
Item AR 18-21
Interface
1 console port
1 x 10/100 Mbps Ethernet interface (WAN)
4 x 10/100 Mbps Ethernet interfaces (LAN)
Processor
MPC8247
SDRAM 64 MB
Flash 8 MB
Hardware
encryption
––
Max. power
10 W
Input
Rated voltage: 100 to 240 VAC; 50 to 60 Hz
Current: 0.5 A
Power
supply
(extern
al)
Output
Voltage: 12 VDC
Current: 1.25 A
Dimensions (W x
D x H)
300 x 180 x 45 mm (11.81 x 7.09 x 1.77 in.)
(the maximum measurements, including the
bulge)
Weight
1kg (2.20 lb)
Operating
temperature
0 to 40 C (32 to 104 F)
Relative humidity
(non-condensing)
5 to 90%
Installation Manual
H3C AR 18-2X Series Routers
Chapter 1 Product Overvie
w
1-4
III. LEDs
You can gather information about the status of the AR 18-21 and
its interfaces by reading the seven LEDs on its cover, as shown below.
Table 1-2 LEDs on the cover of the AR 18-21
LED Description
LAN1/LAN2/
LAN3/LAN4/
WAN0
OFF means no link is present.
ON means a link is present.
Blinking means data is being sent or/and received.
SYS
Blinking means the system is operating normally.
Steady ON or OFF means the system is imprope rly
operating.
PWR
OFF means no power is being supplied.
ON means power is being supplied.
IV. Interface attributes
The interfaces that the AR 18-21 provides are described as
follows:
1) Console port
Table 1-3 Attributes of the console port
Attribute Description
Connector
RJ45
Interface standard Asynchronous RS232
Baud rate
9600 (default) to 115200 bps
Installation Manual
H3C AR 18-2X Series Routers
Chapter 1 Product Overvie
w
1-5
Attribute Description
Service
Connection to an ASCII terminal
Connection to the serial interface on a PC to
run the terminal emulation program on the PC
Command line interface (CLI)
2) Ethernet interface
Table 1-4 Attributes of the Ethernet interface
Attribute 10BASE-T 10/100BASE-T
Connector RJ45
Interface type MDI/MDIX autosensing
Operating
mode
10 Mbps
Full duplex/half
duplex
10/100 Mbps autosensing
Full duplex/half duplex
Supports only L2 switching
Installation Manual
H3C AR 18-2X Series Routers
Chapter 1 Product Overvie
w
1-6
1.2.2 Hardware Features of the AR 18-22
I. Appearance
1) Ethernet LED LAN4 2) Ethernet LED LAN3
3) Ethernet LED LAN2 4) Ethernet LED LAN1
5) WAN LED (WAN1) 6) WAN LED (WAN0)
7) SYSTEM LED (SYS) 8) POWER LED (PWR)
Figure 1-3 Front view of the AR 18-22
1) Power switch 2) Power socket
3) Console port (CONSOLE) 4) Ethernet interface 1 (LAN1)
5) Ethernet interface 2(LAN2) 6) Ethernet interface 3 (LAN3)
7) Ethernet interface 4 (LAN4) 8) Grounding screw
9) WAN interface (WAN0) 10) WAN interface (WAN1)
Figure 1-4 Rear view of the AR 18-22
Installation Manual
H3C AR 18-2X Series Routers
Chapter 1 Product Overvie
w
1-7
II. System specifications
Table 1-5 System specifications of the AR 18-22
Item AR 18-22
Interface
1 console port
2 x 10/100 Mbps Ethernet interface (WAN)
4 x 10/100 Mbps Ethernet interfaces (LAN)
Processor
MPC8247
SDRAM 64 MB
Flash 8 MB
Hardware
encryption
––
Max. power
10 W
Input
Rated voltage: 100 to 240 VAC; 50 to 60 Hz
Current: 0.5 A
Power
supply
(extern
al)
Output
Voltage: 12 VDC
Current: 1.25 A
Dimensions (W x
D x H)
300 x 180 x 45 mm (11.81 x 7.09 x 1.77 in.)
(the maximum measurements, including the
bulge)
Weight
1kg (2.20 lb)
Operating
temperature
0 to 40 C (32 to 104 F)
Relative humidity
(non-condensing)
5 to 90%
Installation Manual
H3C AR 18-2X Series Routers
Chapter 1 Product Overvie
w
1-8
III. LEDs
You can gather information about the status of the AR 18-22 and
its interfaces by reading the eight LEDs on its cover, as shown below.
Table 1-6 LEDs on the cover of the AR 18-22
LED Description
LAN1/LAN2/L
AN3/LAN4/W
AN0/WAN1
OFF means no link is present.
ON means a link is present.
Blinking means data is being sent or/and
received.
SYS
Blinking means the system is operating normally.
Steady ON or OFF means the system is
improperly operating.
PWR
OFF means no power is being supplied.
ON means power is being supplied.
IV. Interface attributes
The AR 18-22 provides a consol port and 10/100 Mbps Ethernet
interfaces. Refer to
1.2.1 IV. for attributes detail.
The WAN1 interface supports only MDI other than MDI/MDIX
autosensing. Other Ethernet interfaces share the same attributes with
the AR 18-21.
Installation Manual
H3C AR 18-2X Series Routers
Chapter 1 Product Overvie
w
1-9
1.2.3 Hardware Features of the AR 18-22-8/18-22S-8
I. Appearance
1) POWER LED (PWR)
2) Connection LEDS of Ethernet Interfaces LAN1-LAN8 (LINK/ACT)
3) Reset 4) Cons ole Port
5) WAN Port (WAN1) 6)WAN Port (WAN0)
7) Speed LEDs of Ethernet Interfaces LAN1-LAN8 (SPEED)
8) Layer2 Ethernet Interfaces LAN1-LAN8
9) SYSTEM LED (SYS)
Figure 1-5 Front view of the AR 18-22-8/18-22S-8
1) Grounding screw 2) Power socket 3) Power switch
Figure 1-6 Rear view of the AR 18-22-8/18-22S-8
Installation Manual
H3C AR 18-2X Series Routers
Chapter 1 Product Overvie
w
1-10
II. System specifications
Table 1-7 System specifications of the AR 18-22-8/18-22S-8
Item AR 18-22-8 AR 18-22S-8
Interface
1 console port
2 x 10/100 Mbps Ethernet interface (WAN)
8 x 10/100 Mbps Ethernet interfaces (LAN)
Processor
MPC8248
SDRAM 64 MB 128 MB
Flash 8 MB 16 MB
Hardware encryption ––
Supported
Max. power
10 W
Input
voltage and
current
AC
Rated voltage: 100 to 240 VAC; 50 to 60
Hz
Current: 0.5 -1 A
Dimensions (W x D x
H)
300 x 225 x 42 mm (11.81 x 8.85 x 1.65 in.)
(the maximum measurements, including
the bulge)
Weight
2kg (4.40 lb)
Operating
temperature
0 to 40 C (32 to 104 F)
Relative humidity
(non-condensing)
5 to 90%
Installation Manual
H3C AR 18-2X Series Routers
Chapter 1 Product Overvie
w
1-11
III. LEDs
You can gather information about the status of the AR
18-22-8/18-22S-8 and its interfaces by reading the twenty-two LEDs
on its cover, as shown below. Every LAN/WAN interface has LEDs
LINK/ACT and SPEED to indicate its running state.
Table 1-8 LEDs on the cover of the AR 18-22-8/18-22S-8
LED Description
LINK/ACT
OFF means no link is present.
ON means a link is present.
Blinking means data is being sent
or/and received.
LAN1/LAN
2/LAN3/LA
N4/LAN5/L
AN6/LAN7
LAN8/WA
N0/WAN1
SPEED
OFF means the link rate is 10 Mbps.
ON means the link rate is 100 Mbps.
SYS
Blinking means the system is operating
normally.
Steady ON or OFF means the system is
improperly operating.
PWR
OFF means no power is being supplied.
ON means power is being supplied.
IV. Interface attributes
The AR 18-22-8/18-22S-8 provides a consol port and 10/100
Mbps Ethernet interfaces. Refer to
1.2.1 IV. for attributes detail.
The WAN1 interface supports only MDI other than MDI/MDIX
autosensing. Other Ethernet interfaces share the same attributes with
the AR 18-21.
Installation Manual
H3C AR 18-2X Series Routers
Chapter 1 Product Overvie
w
1-12
1.2.4 Hardware Features of the AR 18-23-1/18-23S-1
I. Appearance
1) POWER LED (PWR) 2) Reset
3) Console Port (CONSOLE) 4) Ethernet Interface ETH0
5) Ethernet Interface ETH1 6) Ethernet Interface ETH2
7) Ethernet Interface ETH3 8) SYSTEM LED (SYS)
Figure 1-7 Front view of the AR 18-23-1/18-23S-1
1) Grounding screw 2) Power socket 3) Power switch
Figure 1-8 Rear view of the AR 18-23-1/18-23S-1
Installation Manual
H3C AR 18-2X Series Routers
Chapter 1 Product Overvie
w
1-13
II. System specifications
Table 1-9 System specifications of the AR 18-23-1/18-23S-1
Item AR 18-23-1 AR 18-23S-1
Interface
1 console port
4 x 10/100 Mbps Ethernet interface
Processor
MPC8248
SDRAM 64 MB 128 MB
Flash 8 MB 16 MB
Hardware
encryption
––
Supported
Max. power
10 W
Input
voltage and
current
AC
Rated voltage: 100 to 240 VAC; 50 to 60 Hz
Current: 0.5 -1 A
Dimensions (W x D
x H)
300 x 225 x 42 mm (11.81 x 8.85 x 1.65 in.)
(the maximum measurements, including the
bulge)
Weight
2kg (4.40 lb)
Operating
temperature
0 to 40 C (32 to 104 F)
Relative humidity
(non-condensing)
5 to 90%
Loading...