H2O Audio iDV1-5A1, iDV1-75 User Manual

www.H2OAudio.com

Deep Dive Waterproof Case & Speakers

Depth Rating 300ft/90m

For updated manuals please visit our web site www.h2oaudio.com

iDV1-75 20080819

Mask Clip

O-ring

Speaker

iPod

Control Buttons

Lanyard Hole

Insert Holes &

Height Adjuster Holes

LED lights

Battery Cover

Cam Knob

Depth Rating 300ft / 90m

Connector Cable

Cam Knob Lock

Quickstart: Instructions:

I. Getting Familiar with the iDive300 Before using the iDive300 for the ﬁ rst time, it is highly recommended that you become familiar with

I. Read “Getting Familiar with the iDive 300”

II. Unlock and open case

opening and closing the case to ensure the case is sealed properly during use. To verify that you have sealed the case properly we recommend that you test the product without an iPod inside before initial use. Please follow the instructions below:

III. Install batteries (3 AA)

IV. Install iPod speciﬁ c inserts and height adjusters (see page 10 for ﬁ t chart)

V. Install iPod

VI. Turn on iPod

VII. Close and lock Case

VIII. Press and hold the power button on the iDive300 case

(Green LED should light on back of case)

1. Read the iDive300 instruction manual to familiarize yourself with the product.

2. Unlock and open the case (see page 6) and verify the blue O-ring is clean and free of debris.

3. Close and lock the case (see page 7).

4. Immerse the case (without an iPod inside) in water and soak for 30 min.

5. Manipulate the iDive300 controls during submersion.

6. Remove from the water and dry the exterior. Visually inspect the case for any sign of leaks before

opening.

Call H2O Customer Service if you have any questions or concerns.

II. The O-ring

The removable, blue O-ring retained in the lid of the iDive300 is what keeps your iPod safe and dry. The supplied silicone grease helps ensure the O-ring will not twist or become dislodged when closing or opening the case. Lubricating the O-ring does not improve the seal and only a small amount of silicone grease is necessary to lubricate the O-ring. Use only the silicone grease provided to lubricate the O-ring.

IT IS EXTREMELY IMPORTANT YOU ENSURE THE O-RING IS PROPERLY SEATED IN ITS

TRACK AND IS FREE OF DEBRIS BEFORE EACH USE. FAILURE TO DO SO MAY CAUSE DAMAGE TO OR DESTROY YOUR IPOD.

Prior to use verify:

1. The O-ring is lightly lubricated and seated within the track in the lid.

2. The O-ring and contact surface are free of scratches and other imperfections.

4. Install O-ring into the lid ensuring it is aligned properly with the round side of the O-ring facing out.

5. Apply a thin layer of the supplied silicone grease to the O-ring.

For long term storage of the O-ring, store in a plastic bag out of direct sunlight.

Do NOT use if:

1. The O-ring is dry, cracked, twisted, and/or out of alignment.

2. O-ring and/or contact surfaces have any dirt, lint, hair, and/or other debris.

3. The O-ring and contact surface have scratches and other imperfections.

Replacement

H2O Audio has provided an extra O-ring. The O-ring should be replaced annually or in the event of damage, loss, overexposure to direct sunlight, or become misshaped through misuse. To replace the O-ring:

1. Remove the O-ring from the case using the supplied O-ring remover.

2. Install the new O-ring into the lid ensuring it is aligned properly. The round side of the O-ring should

be facing out.

3. Apply a thin layer of the supplied silicone grease to the O-ring.

Cleaning & Storing the O-ring

It is extremely important that you keep the O-ring clean and free of sand, dirt, hair, lint, and other debris. To clean the O-ring:

1. Remove the O-ring from the case using the supplied O-ring remover.

2. Wash the O-ring in warm fresh water (strong detergents, soaps, and chemicals MUST NEVER be

used to clean the case or the O-ring).

3. Allow O-ring to air dry.

III. Opening & Closing the Case

To Open Case

Ensure the exterior of the case and the immediately surrounding area is dry before opening the case. The internal components of the iDive300 are not waterproof

1. Open the cam knob lock

2. Rotate the cam knob counter-clockwise 180°

3. Open Lid

(Please note: The lid may be difﬁ cult to open due to a vacuum created in the case during air travel or shipment).

+ 9 hidden pages