!
WARNING
!
H2O Audio stands behind our products.
Failure to follow our instructions could destroy
your iPod and will void the Warranty. If you have
any concerns, or experience any difficulties with
your H2O Audio product, we are here to help you,
so please contact us directly. We can be reached at:
1.800.708.6080 or 858.623.0339
support@h2oaudio.com
www.h2oaudio.com
S9-75 20070823
STOP
STOP
Please take a moment and visit
www.h2oaudio.com
For updated Instruction Manuals,
Product Registration and to
complete your warranty.
iV6 - 75 20071012
Removable T-Seal Instructions
How to install / replace the T-Seal
The most important feature of your H2O Audio
Waterproof Case is the removable T-Seal.
The removable T-Seal is the main barrier between the
harmful water and your iPod.
It is extremely important that special attention is paid to
ensure the T-Seal is seated completely in all four corners
and the Cases Contact Surface. If the T-Seal is dirty, out of
alignment, twisted or pinched in any way it will
compromise the integrity of the case and should not be
used.
H2O Audio has provided an extra T-Seal (included) in the
event of annual replacement, accidental damage, loss,
overexposure to direct sunlight, or if the T-Seal has become
misshaped though misuse.
1. Unlatch and open case.
2. Starting at any corner, gently remove the T-seal.
(Do not stretch or pull on T-Seal)
2.
3. To install a new or clean T-Seal, start at any
corner, push the T-Seal into the corner and run
your finger along the T-Seal pushing it into the
Case Contact Surface.
4. Ensure the T-Seal is seated properly in all four
corners of the Cases Contact Surface.
3.
4.
How to install / replace the T-Seal
5. Gently close lid and lock latch. The lid should close
without any resistance. If you experience any resistance
when closing the case please call customer service
immediately at 1.800.708.6080 before using the case.
6. Visually inspect the outside of the case and ensure
the T-seal is installed correctly. If the T-Seal is dirty, out
of alignment, twisted or pinched in any way it will
compromise the integrity of the case and should not
be used.
Correct
This T-Seal is correctly seated in a closed
case, sealing the case and protecting the
Î
The misaligned T-Seal becomes pinched between
the base and lid (as Shown) creating an opening in
the case that will cause the case to flood.
iPod from water.
Incorrect
Cleaning & Storing the T-Seal
It is extremely important that you keep the T-Seal
clean & free of sand, dirt, hair, lint, and other
debris.
To clean the T-Seal remove it from the case.
Wash T-Seal in warm fresh water, ensuring all
debris is cleaned from the T-Seal.
*Strong detergents, soaps, and chemicals MUST
NEVER be used to clean the case or the T-Seal.*
Allow T-Seal to air dry. Once dry install back into
the case. Please refer to the “How to install /
replace your T-Seal” on how to properly install
the T-Seal.
For long term storage, store in a plastic bag out
of direct sunlight.
H2O Audio:
1.800.708.6080
858.623.0339
support@h2oaudio.com
www.h2oaudio.com
iN3 - 76 20071112
Belt Clip and Sport Armband
Your Waterproof Case for iPod nano comes with a
removable, reversible Belt Clip and a neoprene Sport
Armband suitable for most active sports. The Belt
Clip is held in place by two screws that can be
installed using a standard Phillips Head screwdriver.
The Belt Clip can be reversed to change the access
direction of the stereo jack.
iN3-39 20071106
h2oaudio.com
iN3
Waterproof Case for the
iPod® nano (3rd Gen)
Printed Instructions
H2O Audio cases are designed for specific Apple iPod models, which vary by
generation and storage size. You must ensure the correct case is purchased
for your specific iPod model.
Before using this system, please be sure to read, understand, and follow the instructions in this manual.
2. Case Features
LatchTight Locking
System
Compatible with
iPod nano (3
Lens Clear
Display Window
Commander Scroll
Wheel Control
SealTight Connector
IMPORTANT: Make sure the seal is fully seated against the housing base each time you close the
housing. Use the lid to compress the seal into the base if required.
TM
rd
Gen)
TM
TM
3. Introduction
The H2O Audio Waterproof Case lets you to listen to digital audio during
active watersports. It houses the Apple iPod nano (3
player.
CASE: The H2O Audio case features the LatchTightTM Locking System which
keeps the unit waterproof during operation and allows for functional control
of the player while in the water with the Commander
NOTE: The iPod is NOT waterproof without the H2O Audio case and
Waterproof Headphones and is NOT covered under the product warranty.
Any attempt to use the case with an audio player other than the Apple iPod
rd
Gen) will void the Warranty.
nano (3
HEADPHONES: The case is only waterproof when combined with H2O Audio
waterproof headphones (sold separately). Use of other headphones with a
3.5mm stereo connector will result in a water resistant case, and should not
be submerged.
rd
Gen) digital media
TM
Scroll Wheel.
4. Leak Test
Before utilizing the system for the first time, it is highly recommended to
perform a 'Leak Test'. Follow the instructions below.
DO NOT INSTALL THE iPod nano (3rd Gen)
INSIDE THE CASE FOR THE LEAK TEST
1. Open the case (Section 5), and verify the T-Seal is clean and free of debris.
2. Close the case (Section 5) and attach H2O Audio Waterproof Headphones.
3. Immerse the case, (without the iPod nano 3
4. Manipulate the Commander
5. Remove from the water, dry the exterior. Visually inspect the case for any sign of leaks
before opening.
6. Open the case upside down to prevent water from dropping into the case during
opening.
TM
Scroll Wheel during submersion.
rd
Gen) in water and soak for 30 min.
5. Unlocking & Locking the Case
Unlocking your case
Slide latch button towards the
1.
unlock icon.
While holding the latch button
2.
towards the unlock icon,
push away from the case to open
the latch.
1.
3.
Unhook the buckle from the base.
3.
Locking your case
Close the lid, and hook the
buckle under the base.
Pull the latch towards the case
2.
and snap close.
Verify the lid & latch are closed
with the button positioned on the
icon prior to entering the water.
Verify the T-Seal is aligned properly.
6. The T-Seal
T-Seal
IT IS EXTREMELY IMPORTANT YOU ENSURE THE T-SEAL IS PROPERLY
SEATED DURING EACH CLOSURE. If it is out of alignment or twisted you
will cause damage to or destroy your iPod.
Prior to use, verify:
1.
T-Seal is aligned properly in the
Contact Surface of the lid prior
to closure.
2.
T-Seal and contact surface have
been cleaned as necessary using
a soft, lint-free cloth.
3.
T-Seal and Contact Surface are
free of scratches and other
imperfections.
DO NOT USE SILICONE GREASE as this will damage the seal.
To ensure the T-Seal is fully seated in the base of the case, firmly squeeze
both sides (the base and lid) of the case together after each insertion of the
player. Always check to make sure the latch is closed and locked prior to use.
If you have any questions or doubts, please contact H2O Audio Customer Support
The removable, black, T-Seal (retained in
the lid), between the base and the lid of
the case is, what keeps your iPod safe and
dry.
T-Seal
Contact Surfaces
iPod nano
Do NOT use if:
1.
T-Seal is twisted or out of
alignment during closure.
2.
T-Seal and Contact Surfaces
have any dirt, lint, hair, and/or
other debris.
3.
You see scratches or imperfections
on the T-Seal or Contact Surfaces.
Water
Housing
7. Installing the iPod into the Case
Installing the iPod
Align the audio port with the
1.
stereo jack in the case.
IMPORTANT: Remove any skins or
covers from your iPod before installing
it into the housing.
Compatible with iPod nano (3rd Gen)
Gently snap the player into the
2.
audio jack. Verify the player is
completely plugged into the
audio jack.
Removing the iPod
Slide the player off
1.
of the stereo jack.
Now the player can
slide straight out of the
case.
NOTE: Do not disturb the T-Seal during removal of the player. If the T-Seal is moved, Please use the
case lid to completely seat the T-Seal.
iN3 - 70 20071106
8. Connecting the Headphones
The SealTightTM Connector is what keeps your audio connection safe and
dry underwater. It is designed specifically to create a seal around the
H2O Audio Waterproof Headphones (sold separately). Using any other
headphones will not have a complete waterproof connection, and
reduces the waterproof rating to water-resistant.
To create a waterproof connection, align the 3.5mm stereo plug on the
1.
headphones with the stereo jack of the case.
Insert the headphones into the stereo jack of the housing, ensuring
2.
that the plug mates securely into the SealTight
CAUTION: The SV Series Headphones do not fit with the SealTightTM Connector boot
featured on the H2O Audio Series housings. If your headphones have a connector
that looks like the one shown below, you can not use them with this housing.
SV Series Headphones Connector
TM
Connector.
9. CommanderTM Scroll Wheel Control
The CommanderTM Scroll Wheel Control is a waterproof assembly, which
allows you to maintain complete control over the iPod’s Click wheel
functions. Refer to iPod Instruction Manual for complete details of how
to use the player.
Menu Button
Next / FastForward Button
Select Button
Scroll Wheel rotates
Clockwise &
Counter- Clockwise
Play / Pause Button
Previous / Rewind
Button
10. General Storage Procedures
For long-term storage, store in a plastic bag out of direct sunlight.
CAUTION: The life of a T-Seal is typically one (1) year. Contact H2O Audio
for spare T-Seals or a maintenance kit. Always remember to reinstall the
T-Seal before next use. Do not expose the housing to extreme heat, such
as the inside of a hot car, or in hot direct sunlight, such as on a beach, or
boat deck. Doing so may cause damage and subsequent flooding.
CAUTION: The housing is succeptible to internal condensation with
extreme temperature fluctuations. Use above 105°F(40C) can result in
internal condensation. When used in temperatures below freezing, frost
will appear on the interior of the housing.
CAUTION: Do not store housing in the following environments:
* Solvents or other chemical fumes
* High humidity
* High Ozone
* Extreme temperature fluctuations
Storing the housing in these conditions may lead to a damaged housing,
causing it to leak.
Rinse the EXTERIOR of the system in fresh water after EACH use:
1. Make sure the housing is securely closed with headphones attached.
2. Soak in clean fresh water for 30 minutes.
3. Rinse the entire system with freshwater
4. Completely dry the entire exterior of the system using a clean soft
cloth.
5. Dry face down so water can properly drain from the Commander
Scroll Wheel.
Strong detergents, soaps, and chemicals MUST NEVER be used to clean
the system.
TM
11. Available Accessories
H3 Waterproof Headphones
(required for use underwater)
SISTM - Sports Integration System
Universal Locking Plate
Bike Mount
Belt Clip Mount
Backpack Mount
*Sport Armband Not Included
Swimbelt designed by swimmers
12. Contact Us
Customer Support is available Monday to Friday 9AM to 5PM PT.
www.h2oaudio.com
P. 800.708.6080 or 858.623.0339
F. 858.225.0815
E. support@h2oaudio.com
Copyright Notice:
This owner’s manual is copyrighted, all rights reserved. It may not, in whole or in part, be copied,
photocopied, reproduced, translated, or formed into any electronic format without prior consent in
writing. H2O Audio is a registered trademark of H2O Audio, Inc. Apple and iPod are registered
trademarks of Apple Inc.
Patents 6396769, 6614722, 6954405, 7263032 Others Pending.
13. General Use Notice
READ THIS MANUAL CAREFULLY. IF YOU HAVE ANY
QUESTIONS PLEASE CONTACT H2O AUDIO CUSTOMER
SUPPORT PRIOR TO USE.
IMPROPER USE OF THIS SYSTEM MAY CAUSE THE USER TO
MAKE MISTAKES OR DECISIONS THAT MAY LEAD TO SERIOUS
INJURY OR DEATH.
IMPORTANT WARNING AND DISCLOSURE:
IT CAN BE POTENTIALLY DANGEROUS TO PLAY YOUR HEADPHONES WHILE ENGAGING IN ACTIVITIES THAT REQUIRE
YOUR FULL ATTENTION. YOU SHOULD EXERCISE EXTREME
CAUTION OR DISCONTINUE USE IN POTENTIALLY HAZARDOUS
SITUATIONS. DO NOT USE THE HEADPHONES WHILE DRIVING,
CYCLING, OR OPERATING ANY MOTORIZED VEHICLE. IT MAY
CREATE A TRAFFIC HAZARD AND IS ILLEGAL IN SOME AREAS.
AVOID USING HEADPHONES AT HIGH VOLUME. HEARING
EXPERTS ADVISE AGAINST CONTINUOUSLY LOUD AND
EXTENDED PLAY. IF YOU EXPERIENCE RINGING IN YOUR EARS,
REDUCE VOLUME OR DISCONTINUE USE.
THE MANUFACTURER DOES NOT WARRANT AND WILL NOT BE
HELD RESPONSIBLE IN ANY WAY FOR DAMAGES TO THE iPod,
OR LOSS OF DATA, INCLUDING LOSS OF DATA STORED IN THE
iPod, RESULTING FROM AN EXCESSIVE IMPACT, THUNDER, OR
AN ELECTRICITY FAILURE, OR WATER DAMAGE. YOU WILL BE
RESPONSIBLE FOR SAFE GUARDING ALL DATA STORED ON
YOUR DEVICE.
14. Warranty Coverage
H2O Audio guarantees, to the original purchaser only, that the equipment purchased
(EXCLUDING THE iPod ) is free of defects in material and/or under normal recreational use
for a period of one year (1) from date of consumer purchase from an Authorized Dealer;
provided that proper care and maintenance have been performed as prescribed by the
owner's guide included with the equipment. Should this product prove to be defective for
any reason (other than those listed as limitations below) the product will be serviced or
replaced at H2O Audio's sole discretion at no charge (excluding shipping and handling).
This warranty shall be void if the registration is not completed and sent to H2O Audio
Customer Services within 30 days of purchase. This warranty shall be void if the
equipment has been tampered with by anyone not authorized to perform service. The
warranty is non-transferable and extends to the original purchaser only and is valid only if
the equipment was purchased from an authorized dealer. Warranty does not extend to
cover damage from accident, abuse, tampering, lack of maintenance, theft, or loss. Service
or modifications by anyone other than an Authorized H2O Audio agent will void the
warranty. H2O Audio will not be responsible for recovery or replacement of the product in
the event of loss or theft. H2O Audio, its Authorized International Distributors, and
Authorized Dealers make no other warranties, either express or implied or orally, or in
writing, with respect to any other warranty coverage except those expressly stated within
the preceding sentences. H2O Audio will not be held responsible for any agreements orally
or in writing with the exception of those expressly included in this warranty statement. The
warranty registration card and the terms contained herein supersede all statements
contained in any and all owner's guides, instruction cards, or other equipment literature or
catalogs. In no event will H2O Audio, its Authorized International Distributors, and
Authorized Dealers be held responsible or liable for any personal injuries resulting from the
use of the covered equipment, or for any other damages, whether direct, indirect,
incidental, or consequential; even if H2O Audio has been advised of such damages.
Warranty does not extend to any damages that may occur to the iPod or loss of any data.
15. Returns
Prior to any return, a Return Authorization (RA) number must be obtained. To receive an
RA number, go online to www.h2oaudio.com/returns.php and follow the simple
instructions on how to return a product. Proof of purchase from an Authorized Dealer
will be required. A copy of the original sales receipt and a copy of the owner's portion of
the warranty card must accompany all correspondence regarding the equipment covered
by this warranty agreement or in direct reference to this warranty.
iN3 - 70 20071106
Loading...