GVision P10PS-J, P10PS-JA-452G User Manual
Precautions
Read all of these instructions and save them for later use.
Follow all warnings and instructions on the product.
Product
- Do not cover or block the vent holes in the case.
- Do not insert sharp objects or spill liquid into the LCD monitor through cabinet slots.
They may cause accident fire, electric shock or failure.
- Disconnect the power plug from the AC outlet if you will not use it for an indefinite period
of time.
- Do not attempt to service this product yourself, as opening or removing covers may
expose you to dangerous voltage points or other risks.
- Do not touch the screen directly with your fingers. You may damage the screen, and oil
from your skin is difficult to remove.
- Do not apply pressure to the screen. The LCD is very delicate.
Power adapter
- Use the type of power adapter, which supplies from manufacturer for safety and electronic
issue.
Plugs
- Do not remove any of the prongs of the monitor's three-pronged power plug.
- Disconnect the power plug from the AC outlet under following conditions:
If you will not use it for an indefinite period time.
When the power cord or plug is damaged or frayed.
If the product does not operate normally when the operating instructions are
followed. Adjust only those controls that are covered by the operating
instructions. Improper adjustment of other controls may result in damage and
will often require extensive work by a qualified technician to restore the product
to normal operation.
If the product has been dropped or the cabinet has been damaged.
If the product exhibits a distinct change in performance, indicating a need for
service.
Power and extension cords
- Do not allow anything to rest on the power cord.
- Do not locate this product where persons will walk on the cord.
- Use the proper power cord with correct attachment plug type. If the power source is 120 V
AC, use a power cord that has UL and C-UL approvals. If the power source is a 240 V AC
supply, use the tandem (T blade) type attachm ent plug with ground conductor power cord
that meets the respective European country's safety regulations, such as VDE for
Germany.
- Do not overload wall outlets or power cords. Ensure that the total of all units plugged into
the wall outlet does not exceed 10 amperes.
1
- Ensure that the total ampere ratings on all units plugged into the extension cord is not
above the cord's rating.
- If the power supply cord, which came with your monitor, is to be connected to the PC
instead of the wall outlet, this equipment is to be used with UL/TÜV approved computers
with receptacle rated 240V AC, 4.0A (minimum).
Environment
- Place the monitor on a flat and leveled surface.
- Place the monitor in a well-ventilated place.
- Keep the monitor away from: overly hot, cold or humid places, places directly under
sunlight, dusty surroundings, equipment that generate strong magnetic fields.
Federal Communication Commission Radio Frequency
International Statement
This equipment has been tested and found to comply with t he limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more the following measures:
Reorient / Relocate the receiving antenna.
•
Increase the separation between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which
•
the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
•
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) This device may cause harmful interference.
(2) This device must accept any interference received, including interference that may cause
undesired operation.
2
Notice:
The use of non-shielded interface with this equipment is prohibited.
If necessary, the user should consult the dealer or an experienced radio / television technician
for additional suggestions. The user may find the following booklet prepared by the Federal
Communications Commission helpful. This booklet is available from the U.S. Government
Printing Office Washington DC, 20402, Stock No. 004-000-00345-4.
The manufacture is not responsible for any radio or TV interference caused by unauthorized
modification of this equipment. It is the responsibility of the user to correct such interference.
Caution: To meet FCC limits for a Class B computing device, a shielded signal cable
should be used.
Canadian Department Of Communications
Compliance Statement
This equipment does not exceed Class B limits per radio noise emissions for a digital apparatus,
set out in the Radio Interference Regulation of the Canadian Depart ment of Communications.
Operation in a residential area may cause unacceptable interference to radio and TV reception
requiring the owner or operator to take whatever steps necessary to correct the interference.
3
Product Description
Congratulations on your purchasing this new generation of monitor. Your LCD monitor
incorporates high quality display into a small light weighted module. It has power-saving
capabilities and emits no X-ray radiation. You will certainly benefit from this monitor in lots
of ways to name some of them, comfort, safety, health, and environmental protection.
This LCD monitor incorporates 10.4” color active matrix thin-film-transistor (TFT) liquid
crystal display to provide superior display performance. A maximum resolution of SVGA
800x600 is ideal for displaying graphics and images. Other outstanding designs that enhance
this LCD monitor’s performance are Plug & Play compatibility, and OSD (On Screen Display)
controls.
Package Contents
Included with your LCD monitor are following items:
10.4” TFT liquid crystal monitor
D-sub 15 pin signal cable
Power Adapter
Power cord
User’s manual
Audio cable (optional)
Video signal cable (optional)
RS232 cable for touch screen (optional)
Product Features
High contrast color TFT LCD display support resolution up to SVGA 800x600.
Compatible with IBM VGA and VESA.
Power management system conforms to VESA DPMS standard.
Universal power adapter.
Support DDC1/2B for Plug & Play compatibility.
Advanced OSD control for picture quality adjustment.
Detachable stand for wall-mounting application.
Optional imbedded audio system.
Optional video-in function.
Optional touch screen function.
4
Cleaning
Gently wipe the screen with a clean camel hair lens brush, or a soft, clean, lint-free cloth.
This removes dust and other particles that can scratch the screen.
Do not apply pressure to the screen surface when wiping it clean.
Do not pour or spray any liquid directly onto the screen or case of the LCD monitor.
Chemical cleaners have been reported to damage the screen or case of the LCD monitor.
Taking a Look
Front View
1. Power Switch Pressing this button turns the display system power on or off.
2. Power LED This LED indicates different status when this unit operates in different
modes.
3. Menu/Select ▲ Pressing this button pops up the OSD m enus on the screen, and used to
select (“Up” direction) the OSD control options on the screen.
4. Menu/Select ▼ Pressing this button pops up the OSD menus on the screen, and used to
select (“Down” direction) the OSD control options on the screen.
5. ＋ This button is used to increase the value of the selected OSD control option.
6. － (1) This button is used to adjust the decreasing value of the selected OSD control
option. (2) used to select input sources (VGA or Video signal) when the OSD “main
menu” function is off (for model with video-in function only).
5
Loading...