Instruction Manual
40cm Pedestal Fan
/ GVA40PF
2
Important Safety Instructions
Store this instruction manual in a safe place, along with your warranty card, purchase
receipt and packaging box for future reference. Please pay particular attention to the
safety information.
- Use this fan only as described in this manual. Other use not recommended may
cause re, electric shock or injury.
- This product is intended for household, industrial and commercial use only.
It is not intended for outside use.
- Fans are designed to create rapid air movement, therefore, make sure the fan is not
placed near drapes or curtains, or any objects that may be drawn into the
fan outlet.
- Never connect the fan to any power source other than the volt alternating current
polarized outlet.
- To protect against electric shock, do not place fan in window, immerse unit plug or
cord in water or spray with liquids.
- Close supervision is necessary when any appliance is used by or near children.
- Unplug the fan from the outlet when not in use, when moving fan from one
location to another and before cleaning.
- Do not operate the fan in the presence of explosive and/or ammable fumes.
- Do not place the fan or any parts near an open ame, cooking or other
heating appliance.
- Do not operate the fan with a damaged cord, plug, after a malfunction or if
dropped or damaged in any manner.
- Avoid contact with moving fan parts.
- To disconnect grip the plug and pull it from the wall outlet. Never yank the cord.
- Always use on a dry level surface.
- Do not operate if the fan housing is removed or damaged.
- Do not operate without fan grilles properly in place.
- Warning: To reduce the risk of re or electric shock, do not use this fan with
any outer speed control.
- Do not leave the fan running unattended.
- Ensure that the fan is switched o from the supply mains before removing
the guard.
- If the supply cord is damaged, it must be replaced by manufacturer or its service
agent or a similarly qualied person in order to avoid a hazard.
- This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
- Children should be supervised to ensure that they do not play with the appliance.
3
1. Safety grille
2. Silent operation
3. 3 speed switches
4. Tilt adjustable pivoting head
1
2
3
4
Parts of your Pedestal Fan
- Never insert ngers, pencils, or any other object through the grille when
fan is running.
- Disconnect fan when moving from one location to another.
- Disconnect fan when removing grilles for cleaning.
- Be sure fan is on a stable surface when operating to avoid overturning.
- DO NOT use fan in window. Rain may create electrical hazard.
- Indoor use only.
4
Operation of your Pedestal Fan
Figure 1
Protruding indents
Plastic nut securing
safety grille
Your new 40cm Pedestal Fan has been shipped un-assembled to reduce waste age of
packing material, paper cartons and weight. Please keep these instruction handy as
they outline how to simply and easily assemble the fan.
1. After removing everything from the carton, locate the motor unit and spin the plastic
nut in an anti-clockwise direction to undo. (Figure 1)
2. Locate the rear safety grille and position over the protruding indents. The safety grille
will only t one way over the protruding intents with the handle facing up. Replace the
plastic nut and tighten, taking care to not over-tighten
3. Locate the fan blades and locking nut. Position the blades over the metal spindle
of the motor and line up the groove on the blades with the “T” protruding from the
metal spindle. After the blade has been put on, tighten the locking nut in the reverse
direction, taking care to not overtighten. As the bolt is secured in the opposite direction
the spinning blades, the locking nut will tighten gradually with the operation of the
appliance. (Figure 2.)
Locking nut
Fan Blade
Figure 2
5
4. The safety grille has 4 clips that now need to be lifted to allow the fan to completely
assemble. (Figure 3.)
5. Align the top locking clip to the top of the rear safety grille that has already been
secured to the fan motor. Lock the side locking clips in place and align the bottom hole
for a security nut and bolt. Undo the security lock and bolt and thread the aligned holes
in the security tools before doing up the bolt with a pair of pliers or similar tool.
6. A screwdriver will be required to assemble the fan base. Remove the 4 sets of nuts
from the bolts and align the fan pole over the corresponding holes in the base. Secure
the base by screwing the nuts and bolts back in. (Figure 4.)
Top locking clip
Side locking clips
Fastening screw
Lower cross base
Upper cross base
Figure 4
6
7. The chrome metal tube is height adjustable in the stand. Loosen the collar holding
the chrome metal tube in place and extend to desired length(Note: the metal tube
maybe located inside the lower housing of the chrome tube). Once the desired height is
reached, tighten the fastening collar to secure the tube. The motor housing will drop on
to the chrome tube where it will need to be fastened with the thumb screw provided.
(Figure 5.)
Fastening thumb screw
Chrome metal tube
Fastening collar
Figure 5
7
Please always ensure appliances are disconnected from the power supply and are
switched o before attempting any cleaning
The appliance is not designed to be dismantled without special tools. Please do not
attempt to separate the unit. Cleaning of the unit should only be attempted with a
slightly damp cloth. After wiping down the unit with the damp cloth, dry any wet spots
with a dry paper towel.
Care & Cleaning Instructions
Loading...