Quick Setup Guide
BTV2
B00GUTY3DK
Setup
Your speaker is partially charged when it arrive so you can use it
right away. For the best reception, keep the speaker within 30 feet
of the device it’s paired to.
Pairing the speaker and a device
•Turn ON the speaker. A tone sounds and the LED blinks.
•Turn ON your device (like a phone or tablet).
•On your device, locate your Bluetooth settings and turn on
Bluetooth.
•In Bluetooth Settings, scan for devices if necessary, then select
Amazon_BT2 from your device’s list. The LED stops blinking and light
blue. Your device and speaker are paired and your speaker is
ready to use.
Packaging list
X1
X1 X1 X1
1
Pairing another device
•Disconnect from the previous device by pressing and holding
the function button. A tone sounds and the LED blinks.
•Repeat the Pair the device steps for your next device.
Note: You can pair multiple devices but you can only have one
device actively paired at a time.
Reconnecting a previously paired device
•Disconnect from any other device by pressing and holding the
function button. A tone sounds and the LED blinks.
•If the speaker doesn’t automatically find the device you want
paired (indicated by the LED blinking blue), go to your device
settings and ensure that Bluetooth is still ON, then select
Amazon_BT2. The speaker and device re-pair.
Play music
•Start playing music on your paired device. You will hear the
music through the speaker.
•On the speaker, press + or – to increase or decrease the
volume
2
Use as a speakerphone
You can listen through the speaker and speak through the
speaker’s microphone during phone calls. Position the speaker
about 2 feet away and speak normally.
If you make a call while paired:
The audio and microphone automatically default to the
speaker.
•Use your phone to make the call
•Press the function button to end the call
If you received a call while paired:
Your phone rings through the speakerphone.
To listen and speaker through the speakerphone, press the
function button to answer the call.
•Press the function button to end the call.
•Press and hold the function button to reject the call.
3
Connect with an audio cable
Connect a 3.5mm audio cable (not included) from the
speaker’s AUX jack to your audio device (like an MP3 player).
Note: When connected to AUX, please disconnect from
Bluetooth, use the controls on the device instead of the
speaker.
MENU
VOL
OFF
ON
AUX
4
Charge the speaker
After turn on the speaker, if the battery level is low, the
speaker’s Red LED flashes. If not charged, the speaker shuts off.
To charge the speaker, connect the USB charging cable to the
charging port and an available USB port on your computer.
If the speaker is ON, the Red LED will “ON” when charging.
If the speaker is OFF, the Red LED will “ON” while charging and
turn off when fully charged.
Remark: Please aware that the Blue LED is in ON/flashes status
when the speaker is “ON”. So, there will have Blue and Red
overlap lighting effect when you charging a “ON” speaker.
OFF
ON
AUX
5
Safety and Compliance
WARNING: To reduce the risk of fire or electrical shock, do not expose the system to rain or moisture.
FCC Information
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of the following
measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
Changes or modifications not expressly approved by the party responsible for
compliance.
May cause interference and void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
6
PRODUCT DISPOSAL INFORMATION
Dispose of this product in accordance with Local and National Disposal Regulations.
WEEE
Regulatory Information: Disposal of Waste Electrical and Electronic Equipment (WEEE)
The Waste Electrical and Electronic Equipment (WEEE) Directive aims to minimize the
impact of electrical of WEEE going to landfill. The symbol on this product or its
packaging signifies that this product must be disposed separately from ordinary
household wastes at its end of life. Be aware that this is your responsibility to dispose
of electronic equipment at recycling centers in order to help conserve natural
resources.
Each country should have its collection centers for electrical and electronic equipment
recycling. For information about your recycling drop off area, please contact your
related electrical and electronic equipment waste management authority, your local city
office, or your household waste disposal service.
7
Loading...