WARNING: The MicroVault Biometric safe or any other firearm storage device cannot
take the place of other safety procedures including advising children of the dangers
of firearms.
WARNING: The manufacturers and distributors of the MicroVault Biometric safe do not
recommend, suggest, advise, promote or otherwise condone the ownership or use
of firearms. We at GunVault Inc. believe the decision to own or use a firearm is a
serious decision that should only be made by an adult who has carefully considered
the risks and benefits of such a decision.
WARNING: The keypad and push buttons on the control panel are electronic. They
have a certain feel to them and may seem different to different people. It is
important for you to become accustomed through practice, as to how the MicroVault
Biometric safe responds to your own personal touch.
WARNING: Never mix alcohol or drugs with firearms or the MicroVault Biometric safe.
Alcohol and other substances likely to impair normal mental or physical functions
should not be used before shooting or handling firearms or the MicroVault Biometric
safe.
WARNING: Never grab your firearm by the trigger when removing or placing into the
MicroVault Biometric safe. Make sure your firearm’s safety mechanism is on.
WARNING: Always point your firearm in a safe direction. Common sense should
dictate which direction is the safest.
WARNING: Always follow the firearm safety rules set out by the firearm’s manufacturer.
WARNING: Be familiar with how firearms work. GunVault recommends that you obtain
as much information as possible on firearm safety.
WARNING: Always handle firearms as if they are loaded and ready to fire. Always
assume that a firearm is loaded.
WARNING: In order to enjoy the maximum security benefits of the MicroVault Biometric
safe product, it must be mounted in place using the equipment provided with the
product, according to the instructions provided herein. Use of this product as a
storage receptacle without mounting according to the instructions provided herein,
may compromise security of the MicroVault Biometric Safe.
- 1 -
Understanding Biometrics
Biometrics are methods of authenticating the identity of person based on
physiological or behavioral characteristics. Biometric fingerprint authentication
refers to technology that measure and analyzes human physical characteristics
for identification and authentication purposes.
Everyone is known to have their own unique individual fingerprints. The
individuality of each fingerprint can be determined by the pattern of ridges and
furrows on the surface of the finger as well as by the minutiae points. Minutiae
points are local ridge characteristics that occur at either a ridge bifurcation or a
ridge ending.
The biometric scanner is a sensitive device that requires care not to damage the
device. In addition, it is recommended that you practice the authentication
process several time in order to become comfortable with the process.
About MicroVault Biometric
MicroVault Biometric is the ultimate solution to complete access control.
Invented and developed by GunVault, MicroVault Biometric provides safe
storage and easily controlled access for handguns, weapons, ammunition,
jewelry and other valuable items including: pharmaceuticals, coins, stamps,
stocks, bonds, critical data and personal documents. MicroVault Biometric
requires no external computer or power to function. Flash memory retains
fingerprint data even during complete battery or electrical failure.
Shipped with your MicroVault Biometric are the following items:
MicroVault Biometric
Security Cable
Two backup keys
Instruction Manual
- 2 -
GETTING STARTED
NOTE: Set your keys to the side. Don’t lock them inside the safe!
Make sure to remove the backup key from the MicroVault Biometric before
use and secure them.
The key is for emergency use only to unlock the case in the event of
fingerprint failure.
If the key is used to access the MicroVault Biometric; it can only be
removed from the lock cylinder by returning the key back to its original
locked position.
Please do not try to remove the key in any other position or this may cause
damage.
Do not try to use the fingerprint scanner and electronic locking system
while the key is in the unit.
- 3 -
ENROLLMENT OF THE ADMINISTRATOR
FINGERPRINTS
NOTE: The unit can store 120 fingerprints with the first two enrolled fingerprints
assigned as administrators. If the Learn Button is pressed and the LED flashes
red once and the unit beeps once the unit has reached its120 fingerprints
maximum.
NOTE: The unit requires the first or the second administrator’s fingerprint to be
enrolled before adding additional fingerprints.
Register the first two fingerprints as the administrator. Press the Learn Button. You will hear one beep and the LED will flash
green indicating the enrollment procedure has started.
Place your finger over the scanner with the tip of your finger at the top of
the finger guide as shown in Figure B.
Make sure you have good, flat contact with the scanner. Begin to swipe
your finger from Position 1 to Position 2 (Figure C), taking 1 to 2 seconds
to complete the swipe. Try to get your entire fingerprint to cross the
scanner.
Once the swipe is completed you will hear a beep. Repeat Step 3 one
more time. After swiping your finger 2 times the unit will beep twice, this
indicates a successful enrollment. If the swipe fails, the LED will flash red
and the unit will wait for another swipe.
Repeat steps 1 through 5 to add the second administrator.
- 4 -
ENROLLING ADDITIONAL USERS
Press the Learn Button. You will hear one beep and the LED will turn green
indicating the enrollment procedure has started.
Swipe the administrator fingerprint from Position 1 to Position 2 (Figure C)
and you will hear two beeps indicating the additional fingerprint is ready for
enrollment.
Place the new finger to enroll over the scanner with the tip of your finger at
the top of the finger guide as shown in Figure B.
Make sure you have good, flat contact with the scanner. Begin to swipe the
new finger from Position 1 to Position 2 (Figure C), taking 1 to 2 seconds
to complete the swipe. Try to get your entire fingerprint to cross the
scanner.
Once the swipe is completed you will hear a beep. Repeat Step 3 one
more time. After swiping your finger 2 times the unit will beep twice, this
indicates a successful enrollment. If the swipe fails, the LED will flash red
and the unit will wait for another swipe.
ACCESSING THE UNIT
NOTE: The MicroVault Biometric can be accessed either by valid fingerprint or
via the keys provided.
Fingerprint Access
Press and release the Start Button, the green LED flashes two times and
the unit beeps once.
Place your finger over the scanner with the tip of your finger at the top of
the finger guide as shown in Figure B.
Make sure you have good, flat contact with the scanner. Begin to swipe
your finger from Position 1 to Position 2 (Figure C), it will take 1 to 2
seconds to complete the swipe. Try to get your entire fingerprint to cross
the scanner.
If the unit detects a match, the LED will flash green two times and you will
hear two beeps, then the unit is open.
If the unit doesn’t detect a match, the LED will flash green and red, you will
be denied access. If an enrolled user is denied access, please try again. If
the problem persists, please delete all users and re-enroll again.
- 5 -
Key Access
NOTE: Key Access is intended for backup use only.
Insert the key into the front of the unit.
Turn clockwise to unlock the unit.
Lift the top of the MicroVault Biometric to open.
To remove the key, close the MicroVault Biometric, turn the key
counterclockwise.
.
DELETING USERS/RESETTING THE UNIT
NOTE: Individual users cannot be deleted from the MicroVault Biometric. All
users will be deleted together.
To delete all fingerprints currently stored on the MicroVault Biometric,
press and hold the Delete Button, the LED will turn red, and then press the
Start Button.
The unit will beep twice and the LED will flash green twice, indicating all
users fingerprints are deleted. If no fingerprints are stored, the red led will
flash once and beep once.
Replacing the Battery
NOTE: Low Battery Warning - When the unit is powered on, if the LED flashes
red and the unit beeps 3 times, this indicates a low battery.
Pull open the battery cover.
Pull out the battery holder, by gently pulling on the ribbon.
a) Remove all old batteries.
b) Insert new 9v battery, following the Positive (+) and Negative (-) guides
on the holder.
Reinsert the battery holder and snap the battery cover back into place.
- 6 -
Security Cable
Loop the security cable around a secured object.
Run one end of the cable through the eye of the other end and pull tight around
object.
Place the loose end of the security cable through the gap on the left side of the
unit as shown in picture and close the lid to secure.
Technical Support
If you have followed the above steps carefully and still have a problem operating your
MicroVault Biometric, phone GunVault Technical Support. Almost all problems can be
solved within minutes over the telephone.
800-222-1055
Requirements for Return & Repair
If possible, do not return your MicroVault Biometric safe to your dealer. Instead, call
GunVault Technical Support Department. GunVault products delivered without a
pre-arranged Return Authorization Number may be returned unopened, at owner
expense, and fees may accrue.
- 7 -
Limited Warranty
1. GunVault (the “Company”) warrants to the original consumer (the “Purchaser’) of any GunVault
safe (the “GunVault safe”) purchased after January 1, 2014 against any damage caused by
fire, burglary or attempted burglary for a period of five (5) years from the date of purchase.
2. The Company warrants to the purchaser that the GunVault safe will be free from defects in
workmanship and materials for a period of one (1) year from the date of purchase.
3.These warranties are not assignable or transferable to any other person.
4. Any damage to the GunVault safe as a result of misuse, tampering, abuse, neglect, accident,
improper installation, modification, unauthorized service, destruction, or the alteration of the
serial number, or use violate of the instructions furnished by the Company will void this
warranty.
The sole responsibility of the Company shall be limited to the repair or replacement (in its sole
5.
discretion) of any component of the GunVault safe which fails to conform to this warranty at no
cost to the purchaser for the period of the warranty.
6. Contact the Company directly to obtain service under this warranty. If it becomes applicable to
send a defective product to the Company, a Return Authorization Number must first be obtained
from the company. In order to obtain service under this warranty, purcasher must provide the
Company with the following items (a) proof of purchase, (b) police or fire department report, (c)
photographs of damaged sad, and (d) written testimonial.
Products shipped without prior Return Authorization and Return Authorization Number may not
7.
be accepted, and the Company will not be responsible for their disposition and/or cost of return
to the owner.
8. The Company will not assume any responsibility for any loss or damage incurred in shipping. All
return authorized products should include a copy of the original invoice in order that this
warranty may be honored.
9. This warranty is not an insurance policy. The Company is not responsible for any manner of
damage to or theft of the Purchaser’s GunVault safe or its contents.
10. We recommend that the enclosed warranty cared be completed in full, and returned to the
Company within ten (10) days of the original date of purchase to validate this warranty.
11. Any implied warranties that the purchaser may have are limited to the duration of the warranties
described above. There are no further warranties that extend or apply beyond the face hereof,
and the company expressly disclaims and excludes any and all warranties of merchant ability or
fitness for a particular purpose. Some states do not allow limitations on how long an implied
warranty lasts, so the above limitation may not apply to you.
12. Repair or replacement shall be the sole remedy for the purchaser under this warranty. The
company shall not be liable for any direct, indirect, incidental or consequential damages, losses
or expense arising from the use or misuse of the GunVault safe. Some states do not allow the
exclusion or limitations of incidental or consequential damages, so the limitation may not apply to
you.
13. This warranty gives you specific legal rights, and you may also have other rights which vary from
state to state.
- 8 -
Notes
- 9 -
- 10 -
Inquiries or questions regarding the MicroVault Biometric should be directed to:
GunVault, Inc.
Technical Support 800-222-1055
Protected by United States Patent Numbers
5,161,396 and 5,549,337
- 11 -
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.