Gunter & Hauer
Instruction Manual
Cooker hood
..
ATALA 1000 BI
ATALA 1060 BI
Content
Safety inform ation
Installation
Start using your cooker hood
Troubleshooting
Maintenance and cle ani n g
Environment al note
3
5
8
10
10
12
SAFETY INSTRUCTIONS
This manual explains the proper installation and use of your cooker hood,
please read it carefully before using even if you are familiar with the product.
The manual should be kept in a safe place for future reference.
Never to do:
● Do not try to use the cooker hood
without the grease filters or if the filters
are excessively greasy!
●Do not install above a cooker with a
high level grill.
●Do not leave frying pans unattende d
during use because over heat ed fat s or
oils might catch fire.
●Never leave naked flames under the
cooker hood.
●If the cooker hood is damaged, do not
attempt to use.
●Do not flambé under the cooker hood.
●CAUTION: Accessible parts may
become hot when used with cooking
appliances.
●The minimum distance between the
supporting surface for the cooking
vessels on the hob and the lowest part
of the cooker hood. (When the cooker
hood is located above a gas appliance,
this distance shall be at least 65 cm)
●The air must not be discharged into a
flue that is used for exhausti ng fumes
from appliances burning gas or other
fuels.
Always to do:
● Important! Always switch off the
electricity supply at the mains during
installation and maintenance such as
light bulb replacement.
●The cooker hood must be installed in
accordance with the installation
instructions and all meas ur e men ts
followed.
●All installation work must be carried
out by a competent person or qualified
electrician.
●Please dispose of the packing material
carefully. Children are vulnerable to it.
● Pay attention to the sharp edges
inside the cooker hood especially
during installation and cleaning.
●Make sure the ducting has no bends
sharper than 90 degrees as this will
reduce the efficiency of the cooker
hood.
●Warning: Failure to install the screws
or fixing device in accordance with
these instructions may result in
electrical hazards
●Warning: Before obtaining access to
terminals, all supply circuit s must be
disconnected.
3
Always to do:
Always to do:
●Always put lids on pots and pans
when cooking on a gas cooker.
●When in extraction mode, air in the
room is being removed by the cooker
hood. Please make sure that proper
ventilation measures ar e being
observed. The cooker hoo d re mov es
odours from room but not steam.
●Cooker hood is for domestic use only.
●If the supply cord is damaged, it must
be replaced by the manufacturer, its
service agent or similarly qualified
persons in order to avoid a hazard.
●This appliance can be used by
children aged from 8 years and above
and persons with reduced physical,
sensory or mental capabilities or lack
of experience and knowledge if they
have been given supervision or
instruction concerning use of the
appliance in a safe way and
understand the hazards involved.
Children shall not play with the
appliance. Cleaning and user
maintenance shall not be made by
children without supervision.
●Warning: Before obtaining access to
terminals, all supply circuit s must be
disconnected.
● Caution: The appliance and its
accessible parts can bec om e hot
during operation. Be careful to avoid
touching the heating elements.
Children younger than 8 years old
should stay away unless they are
under permanent supervision.
● There shall be adequate ventilation of
the room when the range hood is used
at the same time as appliances
burning gas or other fuels.
●There is a fire risk if cleaning is not
carried out in accordance with the
instructions
●Regulations concerning the discharge
of air have to be fulfilled.
●Clean your appliance periodically by
following the method given in the
chapter MAINTENANCE.
●For safety reason, please use only the
same size of fixing or mounting screw
which are recommended in this
instruction manual.
●Regarding the details about the
method and frequency of cleaning,
please refer to maintenance and
cleaning section in the i nstr uc ti on
manual.
●Cleaning and user maintenance shall
not be made by children without
supervision.
●When the range hood and appliances
supplied with energy other than
electricity are simultaneously in
operation, the negative pressure in the
room must not exceed 4 Pa (4 x 10-5
bar).
●WARNING: Danger of fire: do not
store items on the cooking surfaces.
●A steam cleaner is not to be used.
●NEVER try to extinguish a fire with
water, but switch off the appliance and
then cover flame e.g. with a lid or a
fire blanket.
4
INSTALLATION (VENT OUTSIDE)
MOUNTING OF THE V-FLAP
If the cooker hood does not have an assembled V-flap 1, you should mount the halfparts to its body.The images only show an example of how to mount the V-flap,the
outlet may be various according to different models and configuration.
To mount the V-flap 1 you should:
• Mount two half-parts 2 into the body 6
• a pin 3 should be top oriented;
• the axis 4 should be inserted in the holes 5 on body;
• repeat all the operations for the 2nd half-part
INSTALLATION
If you have an outlet to the outside, your cooker hood can be connected as below
picture by means of an extraction duct (enamel, aluminum, flexible pipe or nonflammable material with an interior diameter of 150mm)
Before installation, turn the unit off and unplug it from the outlet.
The cooker hood should be placed at a distance of 65~75cm above the cooking
surface for best effect.
5
Drill a hole in the cupboard according to the size in pic 2.Make sure the distance
between the edge of the hole and the edge of the cupboard edge is at least 17mm.
Installation method 1:
1. Fix the left and right hanging boards with 4pcs ST4*8 screws on the cooker hood
body.See pic 3.
2. After ensuring the position and height of cooker hood ,fix two ST40*30mm screws
in the cabinet against the side of the wall. Make sure that the left and right hanging
board can hang on the screw in the wall.See pic 4.
3. Refer to the picture 5,remove the filter firstly.Press out the lights and dismantle the
wrie of the lights. Then use the screwdriver to unscrew two screws on the panel
and take out off the panel.
6
4. Put the cavity into the cabinet and hang on the screws of the wall.See pic 6.
5. Fasten the cavity from the bottom of the cabinet with 10 pcs ST4*14mm
screws.See pic 7.
6. Refer to the picture 8,put the expansion pipe on the outl e t ,an d le ad i t to outside.
7. According to the reverse order of step 3, install the panel, the light, and the filt er
are back into the cooker hood body sequentially.
Installation method 2:
1. Refer from step 1 to step 4 in the installation method 1, put the cavity into the
cabinet.
2. See pic 9, Use 8 pcs ST4*14screws to secure the cavity to the cabinet from the
inside of the cavity.Ensure that the bottom of the cavity is tightly attached to the
bottom of the cabinet.
3. Follow the step 6 of installation method 1, put the expansi on pi pe on the out let,and
lead it to outside.
4. According to the reverse order of step 3 of installation method 1 , install the panel,
lights, and filter are back into the cavity sequentially.
7
WARNING:
For safety reason, please use only the same
size of fixing or mounting screw which are
evice in
accordance with these instructions may result
Installation method 3:
1. Refer from step 1 to step 4 in the installation method 1, put the cavity into the
cabinet.
2. See pic 10, Use 8 pcs M4*35 screws ,8 pcs washer and 4pcs screw nuts to secure
the cavity to the top of cabinet.Ensure that the bottom of the cavity is tightly
attached to the bottom of the cabinet.
3. Follow the step 6 of instal l ati on meth od 1, put the expansion pipe on the outlet,and
lead it to outside.
4. According to the reverse order of step 3 of installation method 1 , install the panel,
lights, and filter are back into the cavity sequentially.
Note: The expansion pipe mentioned in the all installation is not included in this
product.
recommended in this instruction manual.
Failure to install the screws or fixing d
in electrical hazards.
Start Using Your Cooker Hood
Electronic button
There are five buttons: (Low), (Mid), (High), (Light), (Power).See
picture above.
8
1. After connecting to power, indicator light will lit on, all the output close and the hood
will enter standby mode. The indicator light will be off automatically after reminding
if no operation.
2. Power on: Press power button once, its indicator light will lit on, the hood works
at low speed. Indicator light of low speed will be bright. Press power button
again to close it, and its indicator light will be off. All the function operation of the
hood will be closed, the hood enters into standby mode, and run by circle.
The speed buttons and lamp button can work separately and not controlled by the
power button. When a certain function button is pressed, the hood operates at that
function status. Press (Power) button under any status, the cooker hood will be
switched off without any functions.
3. Press lamp button once; lights will be turn on. Indicator light of lamp
button and power button will lit on. Press lamp button again to turn off the
lights. Indicator light of lamp button and power button will be off. And recycle
like this.
4. Press the (High) button once, motor runs on high speed, the indicator light of
high button and power button will beam . Press high bu t ton agai n and t he
motor will stop. Indicator light of high button and power button will be off,and run by
circle.
5. Press the (Mid) button once, motor runs on middle speed, the indicator light of
middle button and power button will beam. Press middle button again and
the motor will stop. Indicator light of middle button and power button will be off,and
run by circle.
6. Press the (low) button once, motor runs on low speed, the indicator light of l ow
button and power button will beam. Press low button again and the
motor will stop. Indicator light of low button and power button will be off,and run by
circle.
Low speed, mid speed and high speed cannot work at the same time. When hood
7.
is on high speed, press low speed, it will turn to low speed at once; when it is in
low speed, press middle speed, it will turn to middle speed immediately, and so on.
9
TROUBLESHOOTING
Fan switch turned off
Select a fan switch position.
Motor failed
Contact service center.
The distance between the
too far
Fault Possible Cause Solution
Light on, but motor
does not work
Light does not
work, motor does
not work
Oil leakage
Lights not working Broken/Faulty globes
Insufficient suction
The Range hood
inclines
Fan switch failed Contact service center.
House fuses blown Reset/Replace fuses.
Power cord loose or
disconnected
One way valve and the outlet
are not tightly sealed
Leakage from the connecti on o f
chimney and cover
range hood and the gas top is
The fixing screw not tight
enough
Refit cord to power outlet.
Switch power outlet on.
Take down the one way valve
and seal with sealant.
Take chimney down and seal.
Replace globes as per this
instruction.
Refit the range hood to the
correct distance.
Tighten the hanging screw and
make it horizontal.
NOTE:
Any electrical repairs to this appliance must conform to your local, state and
federal laws.Please contact the service centre if in any doubt before
undertaking any of the above.Always disconnect the unit from the power source when
opening the unit.
MAINTENANCE AND CLEANING
Caution:
• Before maintenance or cleaning is carried out, the cooker
hood should be disconnecte d fro m the main power supply.
Ensure that the cooker hood is switched off at the wall socket
and the plug removed.
External surfaces are susceptible to scratches and abrasions, so pl ease fol l ow the
•
cleaning instructions to ensure the best possible result is achieved without damage.
GENERAL
Cleaning and maintenance should be carried out with the appliance cold especially
when cleaning.Avoid leaving alkaline or acid substances (lemon juice, vinegar etc.) on
the surfaces.
10
STAINLESS STEEL
The stainless steel must be cleaned regularly (e.g.weekly) to ensure long life
expectancy.Dry with a clean soft cloth. A specialized stainless ste el cl eani ng fluid m ay
be used.
NOTE:
Ensure that wiping is done along with the grain of the stainless steel to prevent any
unsightly crisscross scratching patterns from appearing.
CONTROL PANEL SURFACE
The inlay control panel can be cleaned using warm soapy water. Ensure the cloth is
clean and well wrung before cleaning. Use a dry soft cloth to remove any excess
moisture left after cleaning.
Important
Using neutral detergents and avoid using harsh cleaning chemicals, strong household
detergents or products containing abrasives,as this will affect the appliance
appearance and potentially remove any printing of artwork on the control panel and
will void manufactures warr antee.
GREASE MESH FILTERS
The mesh filters can be cleaned by hand. Soak them for about 3 minute in water with a
grease-loosening detergent then brush it gently with a soft brush. Please do not apply
too much pressure, avoid to damage it . (Leave to dry naturally out of direct sun light)
Filters should be washed separately to crockery and kitchen utensils. it is advisable
not to use rinse aid.
INSTALLING GREASE MESH FILTERS
• To install filters for the following four steps .
- Angle the filter into slots at the back of the hood.
- Push the button on handle of the filter.
- Release the handle once the filter fits into a resting position .
- Repeat to install all filters.
11
CARBON FILTER-not supplied
Activated carbon filter can be used to trap odors. Normally the activated carbon filter
should be changed at three or six months according to your cooking habit. The
installation procedure of activated carbon filter is as below.
1. Remove the grease filter(s).
2. Hook the carbon filter over the pins that are located at the end of the motor.
3. Turn the carbon filter anticlockwise, until you feel it click into place.
※Repeat this process for the second carbon filter. You need to place a carbon filter at
either end of the motor.
※Refit the motor access panel and fully tighten the screws that you removed
previously.
※Refit the lower and upper chimney sections to the main body of the hood.
NOTE:
• Make sure the filter is securely locked. Otherwise, it would loosen and cause
dangerous.
• When activated carbon filter attached, the suction power will be lowered.
12
BULB REPLACEMENT
Important :
The bulb must be replaced by the manufacturer, its
pply before
ensure perspiration does not come in contact with
the globe as this can reduce the life of the globe.
service agent or similarly qualified persons.
Always switch off the electricity su
carrying out any operations on the appliance. When
handling bulb, make sure it is completely cool down
before any direct contact to hands.
When handling globes hold with a cloth or gloves to
Note:
Before changing the lights, make sure that the appliance is plugged off.
Protect against danger when changing lights, such as wearing gloves.
Changing the lights:
Remove the grease filter.
Use a tool or the hand to press the LED light out.Then slightly pull the light
connecting wire out, and dismantle the terminal of the light connecting wire.
Apply the reverse procedure to install the light back.
• ILCOS D code for this lamp is: DSR-1.5/65-S-64
– Max wattage: 2 ×1.5 W
– Voltage range: DC 12V
– Dimensions:
13
ENVIRONMENTAL PROTECTION:
This product is marked with the symbol on the selective sorting of
contact your local or regional authorities.
waste electronic equi pmen t. This me ans that this product must not
be disposed of with household waste but must be supported by a
system of selective collection in accordance with Directive
2012/19/EU. It will then be recycled or dismantled to minimize
impacts on the environment, electrical and electronic products are
potentially dangerous for the environment and human health due to
the presence of hazardous substances.For more information, please
NOTE:
The following shows how to reduce total environmental impact (e.g. energy use) of the
cooking process).
(1) Install the cooker hood in a proper place where there is efficient ventilation.
(2) Clean the cooker hood regularly so as not to block the airway.
(3) Remember to switch off the cooker hood light after cooking.
(4) Remember to switch off the cooker hood after cooking.
INFORMATION FOR DISMANTLING
Do not dismantle the appliance in a way which is not shown in the user manual. The
appliance could not be dismantled by user. At the end of life, the appliance should
not be disposed of with household waste. Check with you Local Authority or retainer
for recycling advice.
14
Mühlenstrasse 8a, Berlin,14167, Germany
www.gunter-hauer.eu
e-mail: info@gunter-hauer.de
Loading...