Guest Internet GIS-R6, GIS-R3, GIS-R2, GIS-R5, GIS-R4 Quick Setup Manual
...
Copyright © Fire4 Systems Inc., 2012. Al l rights reserved.
Support@guest-internet.com
Hotspot Gateway Product Setup - Quick Start Guide 1
First Time Product Configuration
Connect your laptop computer to one of the LAN ports of the gateway.
Connect the Internet port to your DSL router.
Open your computer browser. Instead of your login page you will see the
page shown below. This page is the SETUP WIZARD.
The setup process has four steps. Follow the instructions to type in the
information requested on each page. Then click on the button to go to the
next page. When the setup process is completed your personalized
wireless Internet service will be ready for your guests to start using. The
setup process is shown overleaf: flip this page over to start the setup
process.
Login to the Admin pages at any time. Connect your computer to the
gateway via an Ethernet cable to a LAN port. Then open your browser and
type in the URL:
http://aplogin.com/admin
The username is
admin
, and the password is the one that you entered
with the wizard.
When the page opens select the option you need in the menu. See the
manual for more information about configuration.
Download the product manual at: http://www.guest-internet.com/gateway
Reset to Factory Defaults
: With the gateway powered up, use a paperclip to press the reset button
through the hole shown. Hold the reset button down for 10 seconds then release. All parameters will be reset.
GIS-R6
connections
12volt power supply
For 110/220volts
Internet
Wireless
access
points
The Guest Internet Hotspot gateway products have Ethernet LAN ports that can
be used to connect wireless access points, Internet café kiosk computers, wired
hotel rooms and business center computers. The Internet (WAN) port must be
connected to the DSL or cable modem.
Connect your computer Ethernet
connector to the LAN connector
of the gateway. Your computer
Ethernet connector should be
configured for dynamic IP or as
a DHCP client. It cannot be used
with a fixed IP.
For operation the WiFi
Hotspot customers will
use the wireless
network or kiosk
computers. Connect
wireless access points
and kiosk computers
to the gateway LAN
port via a switch.
First connect the gateway as shown
in the diagram to configure it using
the setup wizard.
Connect the Internet
connector of the gateway
to the DSL or cable
modem LAN Ethernet
connector. The DSL or
cable router should have
the LAN network
connector configured as a
DHCP server. Check with
the equipment manual to
verify the LAN connector
configuration.
Additional wireless
access points are
connected to the
Ethernet switch.
GIS-R6
DSL
Or
Cable
Internet
Configuration
computer
Product
Configuration
Internet
port
LAN port
Reset
24 volts
Optional rack
mount kit is
available
USE ONLY THE
POWER SUPPLY
SHIPPED WITH
THE UNIT TO
PREVENT
DAMAGE
DO NOT DISCONNECT POWER
DURING RESET TO AVOID DAMAGE
Copyright © Fire4 Systems Inc., 2012. Al l rights reserved.
Support@guest-internet.com
Your gateway unit must have a connection to the
Internet for the configuration process to be completed. If
you see a green YES then proceed to step 2. If a red NO
then click on the link to diagnose the problem.
You may have to set a ‘fixed IP’. If you are not familiar
with setting a fixed IP then ask a network technician to
provide help with this.
Some DSL and Cable routers have a firewall setting that
prevents the gateway from connecting to the Internet.
You may have to change a setting on the router firewall.
Step 2: configure hotspot settings
Finished, click on reboot to start your hotspot
Select your time zone and set your password. Note your
password and keep in a safe place.
If you select unlimited access then your guests will click
on a disclaimer to access the Internet. If you select
controlled access then you will have to generate access
codes for your guests.
Your guests will see this information on the login page
Step 1: test the Internet access
After reboot wait two minutes then open your browser
to see your login page. If you want to make changes
then login again and click on the setup wizard.
Step 3: login page branding
Step 4: select guest access
Hotspot Gateway Product Setup - Quick Start Guide 2
Download the product manual at: http://www.guest-internet.com/gateway
Loading...