Guest Trolling Charger 2607A, Trolling Charger 2608A, Trolling Charger 2610A, Trolling Charger 2611A Owner's Manual

R

Trolling Charger Series

OWNER’S MANUAL

ON BOARD BATTERY CHARGERS

Models Amperage No. Of Banks Volts
2607A 3, 3 Amps 2 Bank 12/24
2608A 6 Amps 1 Banks 12
2610A 5, 5 Amps 2 Banks 12
2611A 5, 5 Amps 2 Banks 12/24

See Connection diagrams for warnings.

IMPORTANT NOTICE

This manual contains important safety and operating instructions for the charger. Read
the entire manual before using. Also read all instructions and cautions for and on the
charger, batteries and equipment in the vicinity of the batteries.

1. INTRODUCING THE CHARGER

The Guest model 2607A, 2608A, 2610A and 2611A are designed to both recharge
your batteries, and extend your battery’s life in applications where it is stored for long
periods of time. They are “3-stage” electronic, completely automatic, lightweight, silent,
battery chargers and each output produces 12 Volts DC at either a full 3, 6 or 5 Amps
(model specific), while using much less AC current than other charger types. Unlike
automotive “trickle” chargers, the 2607A, 2608A, 2610A and 2611A will not boil off the
electrolytes in properly installed and maintained batteries. The red and green LED’s,
mounted on the charger face, let you know the unit is recharging and maintaining your
batteries. This sophisticated device is ideal for recharging and maintaining the 12VDC
batteries in your boat, electric vehicle or cart, ATV, snowmobile or motorcycle.

SAVE THESE INSTRUCTIONS

WARNINGS

THIS CHARGER SHOULD BE USED TO CHARGE ONLY LEAD ACID, GEL CELL,
OR AGM BATTERIES. USE ON OTHER BATTERY TYPES MAY EXPLODE AND
CAUSE PERSONAL INJURY.

RISK OF EXPLOSIVE GASES! WORKING IN THE VICINITY OF LEAD ACID
BATTERIES IS DANGEROUS. BATTERIES GENERATE EXPLOSIVE GASES
DURING NORMAL OPERATION. THEREFORE IT IS OF THE UTMOST
IMPORTANCE THAT EACH TIME BEFORE USING YOUR CHARGER YOU
FOLLOW THE INSTRUCTIONS EXACTLY.

Personal Safety Precautions

Adhere to the following personal safety precautions when installing or working with the
chargers:

1.

Someone should be within voice range or close enough to come to your aid when
you work near a lead-acid battery.

2.

Have plenty of fresh water and soap nearby in case battery acid contacts skin,
clothing, or eyes.

3.

Wear complete eye protection and clothing protection. Avoid touching eyes while
working near a battery.

4.

If battery acid contacts skin or clothing, wash them immediately with soap and
water. If acid enters the eye, flood the eye with cold, running water for at least ten
minutes and get medical attention.

5.

Never smoke or allow an open flame in the vicinity of the battery.

6.

Do not drop a metal tool onto the battery. It may spark, short circuit the battery and
may cause an explosion.

7.

Remove all personal metal items such as rings, bracelets, necklaces, and watches
when working near a lead-acid battery. A battery can produce short circuit currents
high enough to weld a ring or the like to metal, causing a severe burn.

Preparing to Charge Precautions

Before charging a battery with the charger, read the following precautions:

1.

Do NOT operate the charger if the cables or an LED is damaged.

2.

Make sure all accessories on the product you are charging are OFF.

3.

If the battery or batteries must be removed from the product, always remove the
grounded terminal from the battery first.

4.

Be sure the area around the battery is well ventilated while the battery is being
charged. Gas can be forcefully blown away using a piece of cardboard or other
non-metallic material as a “hand fan”.

5.

Clean battery terminals. Be careful to keep corrosion from coming in contact with
eyes.

2

6.

Add distilled water in each cell until battery acid reaches levels specified by the
battery manufacturer, if applicable. Do not overfill. For all batteries, carefully follow
the manufacturer’s recharging instructions.

7.

Never allow the ring terminals to touch each other.

8.

NEVER charge a frozen battery.

9.

Please be sure the DC system to which the charger is connected is not drawing
excessive current from the battery for extended periods of time while the charger is
operating. This is important to ensure the charger correctly transitions through each
charging stage to finish with the float voltage level. If the DC system is drawing
continuous current while charging, reduced life or damage to the battery may occur.

AC Connection and Grounding Precautions

DANGER

DO NOT OPERATE THIS CHARGER WITH A TWO BLADED ADAPTER PLUG OR
EXTENSION CORD. DOING SO CAN RESULT IN SERIOUS PERSONAL INJURY.

AFTER SECURING THE BATTERY CONNECTIONS, PLUG THE AC LINE CORD
INTO AN AVAILABLE AC OUTLET THAT IS PROTECTED BY A GROUND FAULT
CIRCUIT INTERRUPTER (GFCI) BREAKER.

CAUTION: To reduce the risk of shock, connect only to a properly grounded outlet.
NOTE: AC Line Cord color coding is EU style. Line = Brown, Neutral = Blue, Ground =

Green

2. INSTALLING THE CHARGER

Choosing Charging Location

The charger should have at least eight inches of unobstructed area on all sides of the
unit for effective cooling. The case of this charger will become warm during operation.
Because the charger is convection cooled (airflow over the back of the charger), the
optimum mounting position for the charger is vertical. Mounting on its back on a
horizontal surface may cause the charger to slightly reduce amperage output due to the
thermal protection built in. Do not install the charger on carpeted, upholstered, or
varnished surfaces.

Mounting the Charger

1.

Use corrosion resistant 3/16” dia. or # 10 bolts, backed by a flat washer, and
secured to the mounting surface with a split-ring lock washer.

2.

Hold the charger to the mounting surface and mark the holes.

3.

Remove the charger and drill the mounting holes.

4.

Align the charger and assemble the mounting hardware. Secure.

3

Making DC Connections

Check polarity of the battery posts. The POSITIVE (POS., P, +) battery post usually
has a larger diameter than the NEGATIVE (NEG., N, -) post. Connect Red charger
output wire to POSITIVE post, Black charger wire to NEGATIVE. See below diagrams
for more details.

Battery Size Recommendations

The recommended maximum battery size per 3 amp bank is 36AH.
The recommended maximum battery size per 5 amp bank is 60AH.
The recommended maximum battery size per 6 amp bank is 72AH.

2607A Connections

Model

Output

Volts

2607A 12/24 3/3 2 4’/4’ 3.5 x 6.4 x 2.25

Diagram 1. 2607A (3/3 Amps) used with 2 independent 12V Batteries

Output

Amps

Banks

DC Cable
Size

Size (inches)

L x W x H

Input Volts

Input

Amps Max

115VAC

2 Amp

50/60Hz

4

2607A Connection Warnings: For the 2607A, output 1 and output 2 may be
connected in parallel for a 12 V 6 amp output. Both outputs may also be
connected in series for a 24 V output, see below.

2607A Connections

Diagram 2. 2607A used in a 24V system

5