Model Number: R3000
Humidifying Mode: Combination
Power Supply: AC120V, 60Hz
Power Consumption: 140W (40W at cool humidification)
Maximum humidity capacity: About 350cc/Hr. (at highest setting and warm humidification)
Tank Capacity: 1.4 Gallons
Successive Humidity Hours: Up to approximately 72 hours depending on environmental
Before turning on make sure there is water in the unit.
Press the Power Button. The unit will display the current
humidity in the room. Once the unit is turned on it may take a
short time for the humidity reading to stabilize.
8. The current humidity level in the room will be shown
on the display. The humidity reading will not display
below 25%.
9. Timer Button
Press the Timer button and set the number of hours you
would like your Germ Guardian™ Ultrasonic Humidifier to run
(1-hour, 2-hours up to 12 hours).
· If you press the button during operation the remaining time
is displayed.
· Press it again to adjust the time.
Co - means Constant Humidification.
DIRECTIONS FOR USE (cont.)
13. Press to select cold or warm humidification*. Water temperature
is maintained at 40 degrees for cold and 80 degrees for warm.
Warm vs. cool mist is a matter of
personal preference. Warm will
humidify room quicker.
14. Humidity Control Button
Press the Humidity Control Button to change the humidity level.
· Five seconds after pressing this button the current humidity
level will be displayed.
This will not affect the spray output!
Co - means Constant Humidification.
15. Water Refill Button
When the Water Refill Button lights up it is time to refill
the water tank.
E-6
10. Spray Control Button
When you press the Spray Control Button
there are four options to choose from:
Press once for weak
Press twice for middle
Press three times for strong
Press four times for turbo
* You will notice the lights get higher as the spray increases.
11. Auto
Press once for auto. This will keep the unit running continuously
with warm humidification. When selected this setting will automatically work to maintain the humidity in the room at a comfortable level. During this mode the unit operates at a warm
temperature and may shut off when it reaches optimal humidity.
It will restart again as the humidity level begins to decrease.
12. Sleep
Press twice to activate sleep mode. In this mode the unit will
run at warm humidification for 3 hours then shut off. When
selected this will also turn on the moon (sleep indicator) and
turn off all other display lights.
16. Night Lamp Button
Press the night lamp button at the top of the unit to illuminate
the night light feature.
17. Press to display the current temperature in your room.
18. Turn spout to select preferred direction of mist output.
· Always unplug the unit before servicing it in any way.
· Be careful when handling the water if warm humidification was selected. The water
temperature of the water remaining in the unit after use may be high.
· Do not submerse the unit in water, or allow water to enter anywhere on the unit except the
designated water tank.
INSIDE THE BODY OF THE UNIT
While the water tank has been treated with Silver Clean Technology to fight the growth of mold,
regular cleaning of the tank and body is recommended to maximize water cleanliness.
Pour excess water out of the unit. Make sure water does not enter the hole where the water
vapor comes out.
Wash out the unit with fresh water, using a cleaning brush and a soft cloth.
Ultrasonic Metal Disk
Humidity levels become weak when water spots remain on the surface of the ultrasonic
metal disk.
Do not use chemicals or detergents.
OUTER SURFACE OF THE UNIT
Wipe the surface of the unit with a soft damp cloth if needed. Do not use any type of cleaning
chemical as it may corrode the surface.
WATER TANK
If water spots remain in the water tank, wipe the inside with a soft cloth. Do not use soap or
detergents. Silver Clean particles have been added to the water tank to help fight the growth of
mold, mildew and bacteria.
AIR FILTER
Gently wipe away debris from the filter with a soft cloth. This filter does not need to be replaced.
TROUBLESHOOTING GUIDE
PROBLEMSOLUTION
Water vapor & humidity are not
produced.
Air blows but water vapor is not
produced.
Humidity level is low.The surface of the ultrasonic metal disk may be dirty:
Warm humidity is not produced.It may take 10-15 min. before warm humidity is created.
Power Plug: Unplug and then try again.
Power Failure: When the power is returned, try again.
Tank Installation: Make sure the tank is correctly
attached.
Make sure spring on tank cap moves freely when pushed.
Excessive Water: Remove a certain amount of water from
the tank.
The desired humidity is lower than the current
temperature: increase the desired humidity.
Detergent residue in the tank: Wash the tank out
and try again.
Wipe it off with a dry soft cloth. Clean with white vinegar.
The water in the unit is too cold: Replace with cool, but
not cold water.
The mist may not feel warm to the touch.
Check to see if the base of the unit feels warm to the
touch. If so, warm mist is being produced.
ULTRASONIC DISK
Remove spray spout (Fig. 1) and use the enclosed cleaning brush to regularly remove build up
and deposits from this area (Fig. 2). White vinegar will help to prevent this build up.
Fig. 1Fig. 2
STORAGE
· Fully dry the inside and outside of the unit before storing it.
· DO NOT leave water in the unit.
· Store in a cool dry place.
The humidity has a bad smell.
White dust is forming on nearby
furniture.
My current humidity will not go
below 25%.
Poor maintenance or dirty water: Clean the product
thoroughly, and fill it with fresh water.
Hard water will deposit a certain amount of dust. Dust in
the air settles because of the added humidity in the room.
Use distilled water if this becomes a nuisance.
The unit will not display a humidity setting below 25%.
This means the current humidity in your room is at or
below 25%.
o the consumer, Guardian Technologies LLC warrants this product to be free of defects in
T
materials or workmanship commencing upon the date of the original purchase. Save your
original sales receipt to validate start of warranty period.
If this product should become defective within the warranty period, we will repair or replace
any defective parts free of charge. The complete machine must be delivered pre-paid to any
authorized Guardian Technologies LLC warranty service center. Please include complete
information on the problem, day of purchase, copy of original sales receipt and your name,
address and telephone number. If you are not near a warranty station, call the factory for
assistance in the US and Canada at 1-866-603-5900. Use only genuine Guardian Technologies
replacement parts.
The warranty does not include unusual wear, damage resulting from accident, or unreasonable
use of the product. This warranty does not cover unauthorized repairs. This warranty gives you
specific legal rights and you may also have other rights (other rights may vary from state to
state in the U.S.A).
We consider the registration process important to ensuring superior service to our customers,
however submitting this card to Guardian Technologies LLC is optional and does not affect
your rights to utilize this warranty according to the conditions stated above. If you have any
questions or comments about our product call toll free at 1-866-603-5900 or send comments
to: Attn: Customer Service, Guardian Technologies LLC, 7700 St Clair Avenue · Mentor, OH
44060. This warranty can also be registered online at www.germguardian.com.
Número de Modelo: R3000
Modo de humidificación: Combinado
Suministro eléctrico: 120 V CA, 60 Hz
Consumo de electricidad: 140 W (40 W con humidificación fría)
Capacidad de humedad máxima: Aproximadamente 350 cc/hr. (con el ajuste más
elevado y humidificación tibia)
Capacidad del depósito: 5.29 litros (1.4 galones)
Horas de humedad consecutiva: Aproximadamente hasta 72 horas dependiendo de las
condiciones ambientales.
Límites de humedad: 25%-80%
Dimensiones: Ancho – 36.83 cm (14.5 pulg.); longitud – 22.86 cm (9 pulg.);
altura – 30.48 cm (12 pulg.)
Peso: 3.99 Kg. (8.8 libras) (sin incluir el empaque)
PARTES
Boca
Asa
Tapa del
depósito
Tire de la tapa
hacia arriba
para obtener
acceso al cepillo
para limpieza.
Enchufe
Lámpara nocturna
S-2
Cepillo
para
limpieza
Guía de la boca
Cuerpo
Depósito
Filtro de aire
ESPECIFICACIONES Y PARTES DEL PRODUCTO (cont.)
Lámpara nocturna
Temporizador
Control de rociado
Automático/Suspendido
Frío/Tibio
Encendido
Temperatura
actual
Control de
humedad
FUNCIONES Y CONFIGURACIONES
Selección de humidificación tibia o fría
Elija la temperatura de humidificación en base a sus necesidades. La humedad tibia consumirá
más electricidad, pero humidificará la habitación más rápidamente.
Control de rociado
El nivel de rociado puede ajustarse a bajo, medio, alto y turbo.
Temporizador
Le permite seleccionar el número de horas que desea que funcione la unidad.
Nivel de humedad
Se considera que una humedad de 40% a 55% se encuentra dentro de los límites confortables.
Indicador de escasez de agua
Cuando la unidad tiene un nivel bajo de agua, se iluminará el indicador LED de relleno del panel
frontal y la unidad se apagará. Simplemente añada más agua para continuar usando la unidad.
Ajuste de humedad
Puede ajustarse el volumen de humedad de acuerdo a sus necesidades al oprimir el botón de
control de la humedad en el panel frontal.
Tecnología Limpia de Plata
Se han incorporado partículas pequeñas de plata al depósito de agua para evitar la proliferación
de bacterias y moho.
Lámpara nocturna
Provee una lámpara tenue con un interruptor de encendido / apagado.
Antes de encender la unidad verifique que la unidad esté llena
de agua. Oprima el botón interruptor. La unidad mostrará el nivel
de humedad actual de la habitación. Una vez que se enciende la
unidad, la lectura de humedad podría tomar un poco de tiempo
en estabilizarse.
8. En la pantalla se mostrará el nivel de humedad actual de la
habitación. La lectura de humedad no mostrará valores por
debajo de 25%.
9. Botón temporizador
Oprima el botón temporizador y ajuste el número de horas que
desea que funcione el Humidificador Ultrasónico Germ
Guardian™ (por ejemplo, 1 hora, 2 horas hasta un máximo de
12 horas).
· Si oprime el botón mientras la unidad está funcionando, se
mostrará el tiempo que queda.
· Oprímalo nuevamente para ajustar el tiempo.
La palabra “Co” significa humidificación constante.
10. Control de rociado
Cuando oprime el botón de control de rociado
usted debe elegir una de las cuatro opciones
siguientes:
Oprímalo una vez para una humedad ligera
Oprímalo dos veces para una humedad media
Oprímalo tres veces para una humedad fuerte
Oprímalo cuatro veces para turbo humedad
*Podrá notar que las luces son más intensas a medida que
se incrementa el rociado.
INSTRUCCIONES DE USO (cont.)
13. Oprima para elegir una humidificación fría o tibia*. El agua se
mantiene a una temperatura de 4.4 grados C (40 grados F) para la
humidificación fría y a 26.6 grados
C (80 grados F) para una
humidificación tibia. La neblina tibia
o fría es una cuestión de preferencia
individual. La neblina tibia humidificará la habitación más rápidamente.
14. Botón de control de la humedad
Oprima el botón de control de la humedad para cambiar el
nivel de la humedad.
· Las opciones para el nivel de humedad incluyen: 30%, 35%,
40%, 45%, 50%, 55%, 60%, 65%, 70%, 75%, 80%.
· El nivel de humedad actual se mostrará en la pantalla cinco
segundos después de oprimir el botón.
¡Esta acción no afectará la cantidad de rociado!
La palabra “Co” significa humidificación constante.
15. Botón de rellenado de agua
Cuando se ilumina el botón de rellenado de agua indica que es
el momento de rellenar el depósito de agua.
16. Botón de lámpara nocturna
Oprima el botón de lámpara nocturna en la parte superior de la
unidad para activar la luz para la noche.
17. Oprima para mostrar la temperatura ambiente actual.
S-6
11. Automático
Oprímalo una vez para un ajuste automático. De esta manera la
unidad funcionará continuamente con humidificación tibia.
Cuando se selecciona, este ajuste mantendrá automáticamente la
humedad en la habitación en un nivel confortable. En esta modalidad, la unidad funciona a una temperatura tibia y podría apagarse
cuando alcanza el nivel óptimo de humedad. Volverá a encenderse
a medida que el nivel de humedad comienza a disminuir.
12. Modo suspendido
Oprima dos veces para activar el modo suspendido. En esta
modalidad, la unidad funcionará con humidificación tibia durante
3 horas y luego se apagará. Cuando se selecciona, también se
encenderá el icono de la luna (indicador de modo suspendido)
y se apagarán todas las demás luces de la pantalla.
18. Gire la boca de humidificación para elegir la dirección preferida
de salida de la neblina.
· Desconecte siempre la unidad antes de darle mantenimiento.
· Tenga cuidado al tocar el agua si eligió la humidificación tibia. El agua que queda dentro
de la unidad después de usarla puede estar muy caliente.
· No sumerja la unidad en agua ni permita que entre agua en ningún lugar de la unidad,
con excepción del depósito designado para el agua.
INTERIOR DEL CUERPO DE LA UNIDAD
Aunque el depósito de agua ha sido tratado con la tecnología limpia de plata para evitar la
proliferación de moho, se recomienda limpiar regularmente el depósito y el cuerpo de la unidad
para maximizar la pureza del agua.
Saque el exceso de agua de la unidad. Asegúrese que el agua no penetre en el orificio por
donde sale el vapor.
Lave la unidad con agua fresca con un cepillo para limpieza y un paño suave.
Disco Ultrasónico de Metal
Los niveles de humedad tienden a ser leves cuando existen manchas de agua en la superficie del
disco ultrasónico de metal.
No limpie con sustancias químicas o detergentes.
SUPERFICIE EXTERIOR DE LA UNIDAD
De ser necesario, limpie la superficie de la unidad con un paño suave, húmedo. No use ningún
tipo de limpiador químico debido a que puede corroer la superficie.
DEPÓSITO DE AGUA
Si quedan manchas de agua en el depósito, limpie el interior con un paño suave. No use jabón
ni detergentes. Se han añadido partículas nano-silver al depósito de agua para evitar el
crecimiento de moho, roya y bacterias.
GUÍA DE SOLUCIÓN DE PROBLEMAS
PROBLEMASOLUCIÓN
La unidad no produce vapor de
agua ni humedad.
Sale aire pero no se produce
vapor.
Nivel de humedad bajo.La superficie del disco ultrasónico de metal podría estar
Enchufe: Desconéctelo, vuelva a conectar e intente nuevamente.
Interrupción del suministro eléctrico: Cuando se restablezca
el servicio, intente nuevamente.
Instalación de la cubeta: Verifique que la cubeta esté
conectada correctamente.
Cerciórese que el resorte de la tapa del depósito se mueve
libremente si se empuja.
Cantidad excesiva de agua: Saque algo de agua de
la cubeta.
La humedad deseada es menor que la temperatura
actual: aumente el nivel deseado de humedad.
Residuos de detergente en la cubeta: Lave bien la cubeta
e intente nuevamente.
sucio: Límpielo con un paño suave, seco. Límpielo con
vinagre blanco.
El agua de la unidad está demasiado fría: Reemplace con
agua fresca, pero que no esté fría.
FILTRO DE AIRE
Limpie suavemente los residuos del filtro con un paño suave. Este filtro no necesita ser
reemplazado.
DISCO ULTRASÓNICO
Retire la boca de rociado (Fig. 1) y use el cepillo para limpieza incluido para eliminar
periódicamente las incrustaciones y materiales depositados en esta área (Fig. 2). Puede usar
vinagre blanco para prevenir estas incrustaciones.
Fig. 1Fig. 2
ALMACENAMIENTO
· Antes de guardar la unidad seque completamente la superficie interior y el exterior.
· NO deje agua dentro de la unidad.
· Guárdela en un lugar fresco y seco.
S-8
No produce humedad tibia.La humedad tibia tarda de 10 a 15 minutos para
La humedad despide mal olor.
En los muebles cercanos a la
unidad está apareciendo un polvo
blanco.
La humedad actual de la unidad
nunca es menor de 25%.
producirse. Esta neblina podría no estar tibia al tacto.
Verifique si la base de la unidad está tibia al tacto. De ser
así, está generando una neblina tibia.
Mantenimiento deficiente o agua sucia: Limpie la unidad
meticulosamente y llénela de agua fresca.
El agua dura creará ciertos depósitos de polvo. El polvo en
el aire también se asienta debido a la humedad de la
habitación. Si le molesta este polvo, use agua destilada en
lugar de agua del grifo.
La unidad no mostrará una lectura de humedad por debajo
de 25%. Esto significa que la humedad actual de la
habitación es de 25% o menor.
Para el consumidor, Guardian Technologies LLC garantiza que este producto se encuentra libre
de defectos de materiales o mano de obra a partir de la fecha de compra original. Guarde el
recibo de compra original para validar el inicio del período de garantía.
Si durante el período de garantía se encuentra que el producto es defectuoso, repararemos o
reemplazaremos las piezas defectuosas sin ningún costo. El aparato completo debe enviarse
con porte pagado por anticipado a cualquier centro de servicio de garantía autorizado por
Guardian Technologies LLC. Incluya la información completa sobre el problema, fecha de
compra, una copia del recibo de compra original y su nombre, dirección y número de teléfono.
Si su domicilio no se encuentra cerca de una estación de garantía y requiere atención en los
EE.UU. y Canadá, llame a la fábrica al 1-866-603-5900. Use sólo piezas de repuesto genuinas
de Guardian Technologies.
La garantía no cubre los problemas ocasionados por desgaste inusual, daños que resulten por
un accidente o el uso no razonable del producto. Esta garantía no cubre las reparaciones no
autorizadas. Esta garantía le otorga derechos legales específicos y usted pudiera tener otros
derechos adicionales (los cuales varían en cada estado en los EE.UU.)
Consideramos que el proceso de registro es importante para garantizar el servicio superior a
nuestros clientes; sin embargo, el envío de esta tarjeta a Guardian Technologies LLC es
opcional y no afecta sus derechos para utilizar la garantía de acuerdo a las condiciones
estipuladas anteriormente. Si tiene preguntas o comentarios acerca de nuestro producto llame
sin costo al 1-866-603-5900 o envíe sus comentarios a: Attn: Customer Service, Guardian
Technologies LLC, 7700 St Clair Avenue · Mentor, OH 44060. También puede registrar esta
garantía en Internet en www.germguardian.com.
Productos adicionales disponibles de Germ Guardian