Page 1
Product Name: Velocity Harness
Part #: 01700; 01701; 01702; 01703; 01704; 01705; 01706; 01750; 01751; 01752; 01753; 01754; 01755;
99-02-0041
Instruction Manual
Do not throw away these instructions!
Read and understand these instructions before using equipment!
Introduction
Applicable Safety Standards
Worker Classifications
Product Specific Applications
Limitations
Components and Specifications
Installation and Use
Maintenance, Cleaning, and Storage
Inspection
Inspection Log
Safety Information
Labels
ANSI Z359.11 Annex A
1
1
1
2
3
4
4 - 5
5
6
6
7
8
9 - 10
Page 2
Introduction
Thank you for purchasing a Guardian Fall Protection Velocity Harness. This manual must be read and
understood in its entirety, and used as part of an employee training program as required by OSHA or any
applicable state agency.
This and any other included instructions must be made available to the user of the equipment. The user must
understand how to safely and effectively use the Velocity Harness, and all fall safety equipment used in
combination with the Velocity Harness.
User Information
Date of First Use:
Serial #:
Trainer:
User:
Applicable Safety Standards
When used according to instruction specifications, this product meets or exceeds all applicable OSHA 1926
Subpart M, OSHA 1910, ANSI Z359.11-2014, and ANSI A10.32-2012 standards for fall protection. Applicable
standards and regulations depend on the type of work being done, and also might include state regulations if
applicable. Consult regulatory agencies for more information on personal fall arrest systems and associated
components.
Worker Classifications
CAUTION
!
Qualified Person: A person with an accredited degree or certification, and with extensive experience or
sufficient professional standing, who is considered proficient in planning and reviewing the conformity of fall
protection and rescue systems.
Competent Person: A highly trained and experienced person who is ASSIGNED BY THE EMPLOYER to be
responsible for all elements of a fall safety program, including, but not limited to, its regulation, management,
and application. A person who is proficient in identifying existing and predictable fall hazards, and who has
the authority to stop work in order to eliminate hazards.
Authorized Person: A person who is assigned by their employer to work around or be subject to potential or
existing fall hazards.
It is the responsibility of a Qualified or Competent person to supervise the job site and ensure all
applicable safety regulations are complied with.
1
Understand the following definitions of those who
work near or who may be exposed to fall hazards.
Page 3
Product Specific Applications
WARNING
!
Personal Fall Arrest: Velocity Harness may be used to support a MAXIMUM 1 Personal Fall Arrest
System (PFAS) for use in Fall Arrest applications. Structure must withstand loads applied in the
directions permitted by the system of at least 5,000 lbs. Maximum free fall is 6‘, or up to 12’ if
used in combination with equipment explicitly certified for such use. Applicable D-ring: Dorsal.
Restraint: Velocity Harness may be used in Restraint applications. Restraint systems prevent
workers from reaching the leading edge of a fall hazard. Always account for fully deployed length
of lanyard/SRL. Structure must withstand loads applied in the directions permitted by the system
of at least 1,000 lbs. No free fall is permitted. Restraint systems may only be used on surfaces
with slopes up to 4/12 (vertical/horizontal). Applicable D-rings: Dorsal, Chest, Side.
Work Positioning: Velocity Harness may be used in Work Positioning applications. Work
Positioning systems allow a worker to be supported while in suspension and work freely with
both hands. Structure must withstand loads applied in the directions permitted by the system of
at least 3,000 lbs. Maximum allowable free fall is 2’. Applicable D-rings: Side.
Rescue/Confined Space: Velocity Harness may be used in Rescue/Confined Space applications.
Rescue systems function to safely recover a worker from a confined location or after exposed to a
fall. There are various configurations of Rescue systems depending on the type of rescue.
Structure must withstand loads applied in the directions permitted by the system of at least
3,000 lbs. No free fall is permitted. Applicable D-rings: Dorsal, Chest, Shoulder.
Use of equipment in unintended applications may result in serious
injury or death. Maximum 1 attachment per connection point.
For all applications: worker weight capacity range
(including all clothing, tools, and equipment) is 130-420 lbs.
Not all Velocity Harnesses may be used in every application type.
WARNING
!
ALWAYS consider harness D-ring configuration and any other structural
components. A Competent Person MUST make a determination
regarding correct harness application and compatibility.
2
Page 4
Limitations
Fall Clearance: There must be sufficient
clearance below the anchorage connector
to arrest a fall before the user strikes the
ground or an obstruction. When calculating
fall clearance, account for a MINIMUM 2’
safety factor, deceleration distance, user
height, length of lanyard/SRL, harness
stretch, and all other applicable factors.
Diagram shown is an example fall
clearance calculation ONLY.
Swing Falls: Prior to installation or use,
make considerations for eliminating or
minimizing all swing fall hazards. Swing
falls occur when the anchor is not directly
above the location where a fall occurs.
Always work as close to in line with the
anchor point as possible. Swing falls
significantly increase the likelihood of
serious injury or death in the event of a fall.
Compatibility: When making connections
with Velocity Harness, eliminate all possibility
of roll-out. Roll-out occurs when interference
between a hook and the attachment point
causes the hook gate to unintentionally open
and release. All connections must be selected
and deemed compatible with Velocity Harness
by a Competent Person. All connector gates
must be self-closing and self-locking, and
withstand minimum loads of 3,600 lbs. See
the following for examples of
ompatible/incompatible connections:
Fall clearance calculation shown based on standing
worker falling directly in-line with anchor point.
Always consider potential swing fall and other
hazards when calculating fall clearance.
Anchor Point
Level w/Dorsal D-ring
12’ Free Fall
6’ Free Fall
Lanyard
Lanyard
12’
*Eliminate Swing Fall whenever
2’
possible! If Swing Fall exists,
always account for additional
fall clearance.
1.5’
Anchor Point
at Foot Level
5’
2’
Connector
closed and
locked to
D-ring. OK.
Two connectors
to same
D-ring. NO.
Incompatible
or irregular
application,
which may
increase risk
of roll-out. NO.
Two or more
snap hooks or
carabiners
connected to
each other. NO.
3
Connector
to integral
lanyard.
NO.
Connector
directly to
webbing.
NO.
Connector
directly to
horizontal
lifeline. NO.
Page 5
Components and Specifications
Materials: polyester and galvanized steel.
Hardware for part #s 01752 - 01755 is manufactured from powder-coated steel.
Part # Size Description
01700 S - L
01701
01702
01703
01704
01705
01706
01750 S - L Surfacetech Web Velocity Harness w/TB Legs
01751 S - L Surfacetech Web Velocity Harness w/TB Legs & Side D-rings
01752
01753
01755
99-02-0041 S Velocity w/ PT Chest & TB Legs
XL - XXL
S - L
S - L
XL - XXL
S - L
XL - XXL
S - L
XL - XXL
S - L
XL - XXL
Velocity w/ PT Chest & PT Legs
Velocity w/ PT Chest & PT Legs
Velocity w/ 3 D-rings, PT Chest, & PT Legs
Velocity w/ PT Chest & TB Legs
Velocity w/ PT Chest & TB Legs
Velocity w/ 3 D-rings, PT Chest & TB Legs
Velocity w/ 3 D-rings, PT Chest & TB Legs
Hawk Harness w/ PT Chest & TB Legs
Hawk Harness w/ PT Chest & TB Legs
Hawk Harness w/ PT Chest & PT Legs01754
Hawk Harness w/ PT Chest & PT Legs
Installation and Use
All PFAS equipment must be selected and deemed compatible with Velocity Harness by a Competent
Person. ALWAYS follow all instructions of all equipment used in combination with Velocity Harness.
NEVER attach connector to any place on harness other than D-ring. Connector gate must be self-closing
and self-locking, and must withstand minimum load of 3,600 lbs. Any excess strap webbing MUST be
stored in harness Webbing Keepers.
To connect Pass-Through Buckle, angle male buckle so it is positioned to
pass up and through female buckle. Fully insert male buckle so that it lies
flat on top of female buckle.
To connect Tongue Buckle, pull webbing strap through framed tongue component,
and insert framed tongue through grommet to secure.
Roller and Friction Adjustments allow the user to make adjustments to Velocity Harness straps.
Feed webbing through buckle, and slide the buckle down on the strap to tighten, or slide the
buckle up on the strap to loosen.
To adjust dorsal D-ring, slide placard up or down webbing. Dorsal D-ring must rest between the
middle of the shoulder blades.
Dorsal D-ring, chest strap, shoulder straps, and leg straps
MUST be fitted for each individual user.
4
Page 6
1. Hold at dorsal D-ring, and
fully inspect harness according
to specifications of this instruction
manual. Ensure all straps are not
twisted and all buckles are
unfastened.
2. Place harness shoulder straps
over shoulders. Ensure dorsal
D-ring faces out, and is adjusted
to rest between the middle of
the shoulder blades.
3. Connect leg straps around thighs.
Ensure there is no twisting of
webbing. Leg straps should never
dangle or hang loose.
WARNING
!
Any twisting of webbing, or
straps that are fitted too loose
or too tight, can significantly
4. Adjust chest strap height to
lower chest level, approximately
6” from top of shoulders. Connect
chest strap. Ensure there is no
twisting of webbing.
Some steps of donning a harness may require assistance from another person. Upon completely
donning a harness, Guardian Fall Protection recommends that another person, with knowledge of the
safe and correct use of the harness, inspect to ensure the harness is being worn correctly.
5. Adjust chest, leg, and
shoulder straps so they fit
snugly, but still allow for a
full range of movement.
increase the risk of serious
injury or death in the
event of a fall.
Maintenance, Cleaning, and Storage
If a Velocity Harness fails inspection in any way, immediately remove it from service, and contact Guardian to
inquire about its return or repair.
Cleaning after use is important for maintaining the safety and longevity of Velocity Harness. Remove all dirt,
corrosives, and contaminants from Velocity Harness before and after each use. If a Velocity Harness cannot be
cleaned with plain water, use mild soap and water, then rinse and wipe dry. NEVER clean Velocity Harness
with corrosive substances.
When not in use, store equipment where it will not be affected by heat, light, excessive moisture, chemicals,
or other degrading elements.
5
Page 7
Inspection
Prior to EACH use, inspect Velocity Harness for deficiencies, including, but not limited to, corrosion,
deformation, pits, burrs, rough surfaces, sharp edges, cracking, rust, paint buildup, excessive heating,
alteration, broken stitching, fraying, and missing or illegible labels. IMMEDIATELY remove Velocity Harness from
service if defects or damage are found, or if exposed to forces of fall arrest.
Ensure that applicable work area is free of all damage, including, but not limited to, debris, rot, rust, decay,
cracking, and hazardous materials. Ensure that selected work area will support the application-specific
minimum loads set forth in this instruction manual. Work area MUST be stable.
At least every 12 months, a Competent Person other than the user must inspect Velocity Harness. Competent
Person inspections MUST be recorded in inspection log in instruction manual and on equipment
inspection grid label. The Competent Person must sign their initials in the box corresponding to the
month and year the inspection took place.
During inspection, consider all applications and hazards Velocity Harness have been subjected to.
Inspection Log
Date of First Use: __________________.
Product lifetime is indefinite, as long as product passes all inspection requirements. User must inspect
prior to EACH use. Competent Person other than user must complete formal inspection at least every
12 months. Competent Person to inspect and initial.
This inspection log must be specific to one Velocity Harness. Separate inspection logs must be used for
each Velocity Harness. All inspection records must be made visible and available to all users at all
times.
If equipment fails inspection IMMEDIATELY REMOVE FROM SERVICE.
6
Page 8
Safety Information
Failure to understand and comply with safety regulations may result in
WARNING
!
Do not alter equipment. Do not misuse equipment.
Workplace conditions, including, but not limited to, flame, corrosive chemicals, electrical shock, sharp objects,
machinery, abrasive substances, weather conditions, and uneven surfaces, must be assessed by a Competent
Person before fall protection equipment is selected.
The analysis of the workplace must anticipate where workers will be performing their duties, the routes they
will take to reach their work, and the potential and existing fall hazards they may be exposed to. Fall
protection equipment must be chosen by a Competent Person. Selections must account for all potential
hazardous workplace conditions. All fall protection equipment should be purchased new and in an unused
condition.
Fall protection systems must be selected and installed under the supervision of a Competent Person, and used
in a compliant manner. Fall protection systems must be designed in a manner compliant with all federal, state,
and safety regulations. Forces applied to anchors must be calculated by a Competent Person.
Unless explicitly stated otherwise, the maximum allowable free fall distance for lanyards must not exceed 6’.
No free fall allowed for non-LE SRLs. Class A SRLs must arrest falls within 24”; Class B SRLs must arrest falls
within 54”.
Harnesses and connectors selected must be compliant with manufacturer’s instructions, and must be of
compatible size and configuration. Snap hooks, carabiners, and other connectors must be selected and applied
in a compatible fashion. All risk of disengagement must be eliminated. All snap hooks and carabiners must be
self-locking and self-closing, and must never be connected to each other.
A pre-planned rescue procedure in the case of a fall is required. The rescue plan must be project-specific. The
rescue plan must allow for employees to rescue themselves, or provide an alternative means for their prompt
rescue. Store rescue equipment in an easily accessible and clearly marked area.
Training of Authorized Persons to correctly erect, disassemble, inspect, maintain, store, and use equipment
must be provided by a Competent Person. Training must include the ability to recognize fall hazards, minimize
the likelihood of fall hazards, and the correct use of personal fall arrest systems.
NEVER use fall protection equipment of any kind to hang, lift, support, or hoist tools or equipment, unless
explicitly certified for such use.
Equipment subjected to forces of fall arrest must immediately be removed from use.
Age, fitness, and health conditions can seriously affect the worker should a fall occur. Consult a doctor if there
is any reason to doubt a user’s ability to withstand and safely absorb fall arrest forces or perform set-up of
equipment. Pregnant women and minors must not use this equipment.
Physical harm may still occur even if fall safety equipment functions correctly. Sustained post-fall suspension
may result in serious injury or death. Use trauma relief straps to reduce the effects of suspension trauma.
serious injury or death. Regulations included herein are not all-inclusive,
are for reference only, and are not intended to replace a Competent
Person’s judgment or knowledge of federal or state standards.
7
Page 9
Labels
harness only within the capacity range of:
ANSI Z359 recognizes the use of this
ANSI Z359.11–2014
130–310 lbs.
Size:
S
S-L
XL
90781 (Rev. D)-1
WARNING
!
Prior to use, understand all manufacturer
instructions included with equipment
at time of shipment. Improper use of
this equipment could result
in serious injury or death.
IMMEDIATELY remove from service
if subjected to a fall or if
harness fails inspection.
ADVENTENCIA
!
Seguir las instrucciones de fabricación
incluidas con el equipo, al tiempo del
transporte, de la fábrica, antes de usar.
Uso impropio de este equipo puede
resultar en heridas serias o muerte.
INMEDIATAMIENTE quite de servicio
si súbdito a una caída accessorio
o si la falla la inspección.
Guardian Fall Protection
6305 S. 231st St.
Kent, WA 98032
90781 (Rev. D)-4
Material: Polyester & steel
Part #:
DOM:
Serial #:
M
M-XL
XL-XXL
L
L-XL
S-M
M-L
XXL
90781 (Rev. D)-2
INSPECTION GRID
User must inspect prior to EACH use. Competent
Person must complete formal inspection every
12 months. Competent Person to inspect and initial.
Date of First Use: __________________
Product lifetime is indefinite as long as equipment
passes pre-use and Competent Person inspections.
YR
MO
20___ 20___20___ 20___20___
J
F
M
A
M
J
J
A
S
O
N
D
If equipment fails inspection
IMMEDIATELY REMOVE FROM SERVICE
DO NOT REMOVE LABELS
90781 (Rev. D)-5
Compliant with:
OSHA 1910, OSHA 1926 Subpart M,
ANSI Z359.11-2014, and ANSI A10.32-2012.
Capacity Range: 130-420 lbs.
Make only compatible connections.
Prior to use, inspect equipment for rips,
tears, fraying, or any possible structural
deficiency that might compromise the
equipment in a fall. Avoid contact
with sharp and abrasive surfaces.
Cumplir con:
OSHA 1910, OSHA 1926 Subpart M,
ANSI Z359.11-2014, y ANSI A10.32-2012.
Rango de Capacidad: 130-420 lbs.
Nomás haga compatible conexiones.
Inspeccionar el equipo antes de usar;
que no este desgarrado, deshilachado,
deshebrado o cual es quiere estructural
incapacidad que pueda comprometer el
equipo en una caída. Evitar contacto
con orillas filosas o abrasivo.
Made in USA / Hecho en USA
90781 (Rev. D)-3
PARK
LANYARD
HERE – SEE
INSTRUCTIONS
LG
Size Tag
All labels located
on harness strap
beneath label cover
8
Page 10
ANSI Z359.11 Annex A
Note: This information from the Z359.11 standard is required to be included in the instruction manual for the end user:
ANSI/ASSE Z359 Requirements for Proper Use and Maintenance of Full Body Harnesses (Note: These are general requirements and
information provided by ANSI/ASSE Z359, the Manufacturer of this equipment may impose more stringent restrictions on the use of
the products they manufacture, see the Manufacturer’s instructions.)
1. It is essential that the users of this type of equipment receive proper training and instruction, including detailed procedures for the
safe use of such equipment in their work application. ANSI/ASSE Z359.2, Minimum Requirements for a Comprehensive Managed Fall
Protection Program, establishes guidelines and requirements for an employer’s managed fall protection program, including policies,
duties and training; fall protection procedures; eliminating and controlling fall hazards; rescue procedures; incident investigations; and
evaluating program effectiveness.
2. Correct fit of a Full Body Harness is essential to proper performance. Users must be trained to select the size and maintain the fit of
their Full Body Harness.
3. Users must follow manufacturer’s instructions for proper fit and sizing, paying particular attention to ensure that buckles are
connected and aligned correctly, leg straps and shoulder straps are kept snug at all times, chest straps are located in the middle chest
area and leg straps are positioned and snug to avoid contact with the genitalia should a fall occur.
4. Full Body Harnesses which meet ANSI/ASSE Z359.11 are intended to be used with other components of a Personal Fall Arrest system
that limit maximum arrest forces to 1800 pounds (8kN) or less.
5. Suspension intolerance, also called suspension trauma or orthostatic intolerance, is a serious condition that can be controlled with
good harness design, prompt rescue and post fall suspension relief devices. A conscious user may deploy a suspension relief device
allowing the user to remove tension from around the legs, freeing blood flow, which can delay the onset of suspension intolerance. An
attachment element extender is not intended to be attached directly to an anchorage or anchorage connector for fall arrest. An energy
absorber must be used to limit maximum arrest forces to 1800 pounds (8kN). The length of the attachment element extender may
affect free fall distances and free fall clearance calculations.
6. Full Body Harness (FBH) Stretch, the amount the FBH component of a personal fall arrest system will stretch and deform during a
fall, can contribute to the overall elongation of the system in stopping a fall. It is important to include the increase in fall distance
created by FBH Stretch, as well as the FBH connector length, the settling of the user’s body in the FBH and all other contributing factors
when calculating total clearance required for a particular fall arrest system.
7. When not in use, unused lanyard legs that are still attached to a Fully Body Harness D-ring should not be attached to a work
positioning element or any other structural element on the Full Body Harness unless deemed acceptable by the competent person and
manufacturer of the lanyard. This is especially important when using some types of “Y” style lanyards, as some load may be
transmitted to the user through the unused lanyard leg if it is not able to release from the harness. The lanyard parking attachment is
generally located in the sternal area to help reduce tripping and entanglement hazards.
8. Loose ends of straps can get caught in machinery or cause accidental disengagement of an adjuster. All Full Body Harnesses shall
include keepers or other components which serve to control the loose ends of straps.
9. Due to the nature of soft loop connections, it is recommended that soft loop attachments only be used to connect with other soft
loops or carabiners. Snaphooks should not be used unless approved for the application by the manufacturer.
Sections 11-17 provide additional information concerning the location and use of various attachments that may be provided
on this FBH.
10. Dorsal - The dorsal attachment element shall be used as the primary fall arrest attachment, unless the application allows the use
of an alternate attachment. The dorsal attachment may also be used for travel restraint or rescue. When supported by the dorsal
attachment during a fall, the design of the Full Body Harness shall direct load through the shoulder straps supporting the user, and
around the thighs. Supporting the user, post fall, by the dorsal attachment will result in an upright body position with a slight lean to
the front with some slight pressure to the lower chest. Considerations should be made when choosing a sliding versus fixed dorsal
attachment element. Sliding dorsal attachments are generally easier to adjust to different user sizes, and allow a more vertical rest
position post fall, but can increase FBH Stretch.
11. Sternal - The sternal attachment may be used as an alternative fall arrest attachment in applications where the dorsal attachment
is determined to be inappropriate by a competent person, and where there is no chance to fall in a direction other than feet first.
Accepted practical uses for a sternal attachment include, but are not limited to, ladder climbing with a guided type fall arrester, ladder
climbing with an overhead self-retracting lifeline for fall arrest, work positioning and rope access. The sternal attachment may also be
used for travel restraint or rescue.
When supported by the sternal attachment during a fall, the design of the Full Body Harness shall direct load through the shoulder
straps supporting the user, and around the thighs. Supporting the user, post fall, by the sternal attachment will result in roughly a
sitting or cradled body position with weight concentrated on the thighs, buttocks and lower back. Supporting the user during work
positioning by this sternal attachment will result in an approximate upright body position.
9
Page 11
If the sternal attachment is used for fall arrest, the competent person evaluating the application should take measures to ensure that a
fall can only occur feet first. This may include limiting the allowable free fall distance. It may be possible for a sternal attachment
incorporated into an adjustment style chest strap to cause the chest strap to slide up and possibly choke the user during a fall,
extraction, suspension, etc. The competent person should consider Full Body Harness models with a fixed sternal attachment for
these applications.
12. Frontal - The frontal attachment serves as a ladder climbing connection for guided type fall arresters where there is no chance to
fall in a direction other than feet first, or may be used for work positioning. Supporting the user, post fall or during work positioning,
by the frontal attachment will result in a sitting body position, with the upper torso upright, with weight concentrated on the thighs
and buttocks. When supported by the frontal attachment the design of the Full Body Harness shall direct load directly around the
thighs and under the buttocks by means of the sub-pelvic strap. If the frontal attachment is used for fall arrest, the competent person
evaluating the application should take measures to ensure that a fall can only occur feet first. This may include limiting the allowable
free fall distance.
13. Shoulder - The shoulder attachment elements shall be used as a pair, and are an acceptable attachment for rescue and
entry/retrieval. The shoulder attachment elements shall not be used for fall arrest. It is recommended that the shoulder attachment
elements be used in conjunction with a yoke which incorporates a spreader element to keep the Full Body Harness shoulder straps
separate.
14. Waist, Rear - The waist, rear attachment shall be used solely for travel restraint. The waist, rear attachment element shall not be
used for fall arrest. Under no circumstances is it acceptable to use the waist, rear attachment for purposes other than travel restraint.
The waist, rear attachment shall only be subjected to minimal loading through the waist of the user, and shall never be used to
support the full weight of the user.
15. Hip - The hip attachment elements shall be used as a pair, and shall be used solely for work positioning. The hip attachment
elements shall not be used for fall arrest. Hip attachments are often used for work positioning by arborists, utility workers climbing
poles and construction workers tying rebar and climbing on form walls. Users are cautioned against using the hip attachment
elements (or any other rigid point on the Full Body Harness) to store the unused end of a fall arrest lanyard, as this may cause a
tripping hazard, or, in the case multiple leg lanyards, could cause adverse loading to the Full Body Harness and the wearer through the
unused portion of the lanyard.
16. Suspension seat - The suspension seat attachment elements shall be used as a pair, and shall be used solely for work positioning.
The suspension seat attachment elements shall not be used for fall arrest. Suspension seat attachments are often used for prolonged
work activities where the user is suspended, allowing the user to sit on the suspension seat formed between the two attachment
elements. An example of this use would be window washers on large buildings.
USER INSPECTION, MAINTENANCE AND STORAGE OF EQUIPMENT
Users of personal fall arrest systems shall, at a minimum, comply with all manufacturer instructions regarding the inspection,
maintenance and storage of equipment. The user’s organization shall retain the manufacturer’s instructions and make them readily
available to all users. See ANSI/ASSE Z359.2, Minimum Requirements for a Comprehensive Managed Fall Protection Program,
regarding user inspection, maintenance and storage of equipment.
1. In addition to the inspection requirements set forth in the manufacturer’s instructions, the equipment shall be inspected by the user
before each use and, additionally, by a competent person, other than the user, at interval of no more than one year for:
• Absence or illegibility of markings.
• Absence of any elements affecting the equipment form, fit or function.
• Evidence of defects in, or damage to, hardware elements including cracks, sharp edges, deformation, corrosion, chemical attack,
excessive heating, alteration and excessive wear.
• Evidence of defects in or damage to strap or ropes including fraying, unsplicing, unlaying, kinking, knotting, roping, broken or
pulled stitches, excessive elongation, chemical attack, excessive soiling, abrasion, alteration, needed or excessive lubrication, excessive
aging and excessive wear.
2. Inspection criteria for the equipment shall be set by the user’s organization. Such criteria for the equipment shall equal or exceed
the criteria established by this standard or the manufacturer’s instructions, whichever is greater.
3. When inspection reveals defects in, damage to, or inadequate maintenance of equipment, the equipment shall be permanently
removed from service or undergo adequate corrective maintenance, by the original equipment manufacturer or their designate,
before return to service.
Maintenance and Storage
1. Maintenance and storage of equipment shall be conducted by the user’s organization in accordance with the manufacturer’s
instructions. Unique issues, which may arise due to conditions of use, shall be addressed with the manufacturer.
2. Equipment which is in need of, or scheduled for, maintenance shall be tagged as unusable and removed from service.
3. Equipment shall be stored in a manner as to preclude damage from environmental factors such as temperature, light, UV, excessive
moisture, oil, chemicals and their vapors or other degrading elements.
1085047 (Rev. R)
Distributed by Engineered Fall Protection | Sales@EngineeredFallProtection.com | (314) 492-4422 | www.EngineeredFallProtection.com
Loading...