Guardhat Position
Board
GHP2470
User Guide
DE
Table of contents
English
1 Mechanics, technical data ......................................................................................... 3
1.1 Socket P1 ................................................................................................................... 4
1.2 Socket P2 ................................................................................................................... 4
1.3 Socket PULSE Antenna .............................................................................................. 4
1.4 Socket PHASE Antenna ............................................................................................. 4
2 Technical data ........................................................................................................... 5
2.1 Radio .......................................................................................................................... 5
2.2 Power supply ............................................................................................................. 5
2.3 Environment and dimensions .................................................................................... 5
2
DE
1 Mechanics, technical data
PULSE
PHASE
Position Board Top View
Posititon Board Bottom View
3
DE
1.1 Socket P1
Pin
Description / Function
1
Serial Rx
2
Serial Tx
3
Power Control
4
3.3V Out
5
Ground
Pin
Description / Function
1 to 6
Power Supply – Akku in – 3.2 V to max. 5 V
15 to 20
Ground
Typ: T1M-05-F-SH-L-K
1.2 Socket P2
Typ: ASP-205221-1
1.3 Socket PULSE Antenna
SMP (male)
1.4 Socket PHASE Antenna
UFL (male)
Used Antennas:
Taoglas FXP70.07.0053A ,
Taoglas FXUWB20.07.0100C
4
DE
2 Technical data
Radio PULSE (Location)
Wireless technology
IEEE 802.15.4-2011 UWB
Frequency range
3100 MHz – 4800 MHz
Output power
0.037 mW (-41.3 dBm/MHz)
Antenna
SMP male
Radio PHASE (Communication and optional location)
Wireless technology
IEEE 802.15.4
Frequency range
2.40 to 2.48 GHz ISM-Band
Output power
Max. 4 dBm (adjustable)
Band width
2 MHz; Data transmission via 802.15.4 channels (adjustable)
Antenna
UFL male
Power supply
Energy supply
3.2 V to max. 5 V from external LiIon-Akku
Power Consuption
max. 2.5 W
Environment and dimensions
Case
None
IP-Protection
None
Weight
approx. 85 g
Temperature range
-15 °C to +50 °C
2.1 Radio
2.2 Power supply
2.3 Environment and dimensions
5
DE
Disclaimers:
FCC
“Changes or modifications not expressly approved by the manufacturer could void the user’s authority to
operate the equipment”. “This device complies with Part 15 of the FCC rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.”
FCC Interference Statement (Part 15.105 (b))
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
In order to comply with FCC RF Exposure requirements, the antenna used for this transmitter must be
installed to provide at least 2 cm separation from the human body at all times.
IC
“This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the
following two conditions:
(1) This device may not interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.”
“Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de
brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le fonctionnement.”
For the USA:
“Contains Transmitter Module FCC ID: 2AR6OGHP2470” or “Contains FCC ID: 2AR6OGHP2470”. Any
similar wording that expresses the same meaning may be used.
For Canada:
“Contains Transmitter Module IC: 24751-GHP2470” or “Contains IC: 24751-GHP2470”. Any similar wording
that expresses the same meaning may be used.”
6
DE
20190212-5206189-TD 7
Loading...