Guangzhou Panyu Juda Car Audio Equipment WSP67 User Manual
TY-WSP67
Wireless Speaker
Thank you for purchasing this pro duct.
To use this product safely, read and understand this operation manual thoroughly before using
it. Afte r reading this manual, keep it in a safe place so th at it can be used when necessar y.
Safety precautions
The infor mation you need to prev ent danger to the user an d other people as well a s property
damage is described below. “Description of signs” shows dierent categories of the degree
of danger or d amage that may occur due to wr ong handling. “Des cription of symbo ls” shows
the meaning of the symbols.
Important notes
• This book is only a guide for user's operation, not a criterion for conguration.
• Only use at tachments/accessories specied by the manufacturer.
The lightning ash is intended to alert the user to the presence of
dangerous voltage within the product's enclosure, and touching the
internal components may result in a risk of electric shock to persons.
The exclamatory mark is intended to alert the user to the presence of
important operating instructions.
To reduce the risk of e lectric shock or r e, do not open the cover. Refer
servicing to qualied service personnel.
Description of signs
Indicates that there is a risk of death or serious injury.
Indicates that there is a risk of minor injury or property damag e.
Description of symbols
Indicates “Prohibition” or “You must
not do” with pictures and text.
What to do in the case of an abnormality
• Stop using the device immediately in case of an abnormality or failure.
• Remove the power plug immediately when water or any foreign object enters the
interior of the device. It may cause a re or electric shock. Remove the power plug
immediately, and contact your dealer for a repair.
Power cord and power plug
To reduce the risk of re, electric shock or produc t damage,
• Insert the power plug fully into an AC receptacle.
• If you nd dus t on the power plug pin o r pin installati on surface, rem ove the power
plug and remove the dust.
• The mains plug or an appliance coupler is used as a disconnecting device, the
disconnecting device shall remain readily operable.
• Do not inser t or remove the power plug with a wet hand.
• Observe the following when handling the power cord.
• Do not damage it. • Do not modify it (e.g. extension).
• Do not heat it. • Do not pull it.
• Do not place a heav y object on it. • Do not pinch it.
• Do not bend it forcefully. • Do not twist it.
• Do not bundle it.
• If the device will not be used for a long time, remove the power plug from the
receptacle.
• Do not use any power cord other than the one that comes with the device.
• Do not use the power cord that comes with the device for any other produc t.
Operation Manual
5016900
Indicates “Mandator y Action” or “Do as
indicated” with pic tures and text.
Usage
To reduce the risk of re, electric shock or produc t damage,
• Do not disassemble, repair, or modify the unit . Refer servicing to qualied service
personnel.
• Do not step on, throw the power supply or unit, or expose them to a strong shock.
• Do not throw the unit into re.
• Do not install this unit in a conned or built-in space such as a book case or similar
unit, and ke ep a well-ventila ted conditions. T he ventilation sh ould not be imped ed
by covering the ventilation openings with items such as newspaper, table-cloths,
curtains etc.
• Do not expose this unit to rain, moisture, dripping or splashing.
• Do not place objects lled with liquids, such as vases, on this unit.
• Do not inser t any foreign object into the dev ice.
• In case of lightning, do not touch the power cord.
• Place the unit on a at surface away from sources of direct sunlight or excessive
heat.
• The unit is not for use by children, and keep it out of reach of children.
• Before carrying the device, remove the power plug from the receptacle.
• Do not place a heavy object on the device.
• To prevent possible hearing damage, do not listen at high volume levels for long
periods.
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instruc tions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer's
instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the third prong are provided for
your safet y. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when movin g the cart/appar atus combination to avoid inj ury from tip- over.
13. Unplug this apparatus during lightning storms or when unused for long
periods of time.
14. Refer a ll servicing to q ualified ser vice person nel. Servic ing is required wh en the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spil led or objects have f allen into the appara tus, the apparatus has b een exposed to
rain or moisture, does not operate normally, or has been dropped.
This equipment is a Class II or double insulated electrical appliance. It has been
15.
designed in such a way that it does not require a safety connection to electrical ear th.
16. No naked flame sources, such as lighted candles, should be placed on the apparatus.
17. Attention should be drawn to environmental aspects of battery disposal.
18. The product is designed to use in moderate climates.
FCC Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance
20CM bet ween the radiator & yo ur body.
FCC Statement
This devi ce complies with Pa rt 15 of the FCC Rules. Ope ration is subjec t to the followi ng
two conditions:
1) This device may not cause harmful inter ference, and 2) This device must accept any
interference received, including interference that may cause undesired operation.
Note: This e quipment has bee n tested and found to c omply with the limi ts for a Class B
digital d evice, pursua nt to part 15 of the FCC Rule s. These limit s are designe d to provide
reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference
to radio communication. However, there is no guarantee that interference will not
occur in a par ticular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment o
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit dierent from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
IC-CANADA
This device complies with Industry Canada license-exempt RSS standard(s). Operation
is subject to the following two conditions: (1) this device may not cause interference,
and (2) this devi ce must accept any inte rference, in cluding inter ference that may cau se
undesired operation of the device.
This Class [B] digital apparatus complies with Canadian ICES-003.
Cet appareil s’accorde avec Industrie Canada licence-exempte RSS standard. (1)
cet appareil ne peut pas causer l’inter vention, et (2) cet appareil doit accepter de
l’inter vention, y compris l’intervention qui p eut causer l’operation non desiree de.
Cet appareil numerique de la classe B est conforme a la norme NMB-0 03 du Canada.
California Prop 65 Warning
This product contains chemicals, including lead, known to the
State of California to cause cancer and birth defects or other
reproductive harm. Wash hands after handling.
Disclaimer
• Toshiba shall not be responsible for any damage caused by an earthquake,
thunderstorm, ood damage, re for w hich Toshiba is not resp onsible, acts of a third
party, other accidents, or damages caused by the user’s willful acts or negligence,
misuse, or use in abnormal conditions.
• Toshiba shall not be responsible for any damage caused by failure to observe the
information described in the operation manual.
Disposal
• When disposing of this device, observe the laws, or ordinances and rules of the local
government.
• When disposing of the batter y, make a request to a recycle agency for disposal.
About Using Bluetooth®
This unit is designed for use with Bluetooth® wireless devices compatible with the HFP, HSP,
A2DP and AVRCP streaming audio proles. Refer to your Bluetooth® device’s user manual or
technical support to determine if your Bluetooth® device supports these proles.
Frequency band used
This unit uses the 2.4 GHz frequency band. However other wireless devices may use 2.4 GHz
frequency band as well and may cause interference with each other. To avoid interference,
please refrain from the use of the unit at the same time with other wireless devices.
Certication of this device
This unit conforms to frequency restrictions and has received certication based on
frequency laws, so a wireless permit is not necessary.
However, the following action is punishable by law in some countries:
• Taking apart/modifying the unit.
Usage restrictions
• Wireless transmission and/or use with all Bluetooth® equipped devices is not guaranteed.
• A device fea turing the Blue tooth® functio n is required to con form to the Blueto oth® standard
specied by Bluetooth SIG, and be authenticated. Even if the connected device conforms
to the above mentioned Bluetooth® standard, some devices may not be connected or work
correctly, depending on the features or specications of the device.
Range of use
Use this device within an unobstructed 10 m range. The range of use or perimeter may be
shortened depending on any obstructions, devices causing interference, other people in the
room, or the construction of the building. Please note that the range mentioned above is
not guaranteed.
The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. and are used
under license.
Note
• This unit may receive radio interference caused by mobile telephones during use. If
such interference occurs, please increase separation between this unit and the mobile
telephone.
Maintenance
To clean this system, wipe with a soft, dry cloth.
• Never use alcohol, paint thinner or benzine to clean this system.
• Before using chemical cloth, read the instructions that came with the cloth carefully.
Connecting the AC cord
Insert the provided AC cord into the AC power socket on the back of
1
the speaker.
Insert the power plug into an AC receptacle.
2
The standby indicator lights in red.
Press the POWER/FUNCTION button to turn on the speaker.
3
The standby indicator lights o and one of the function indicators (USB/LINE IN/
BLUETOOTH) lights up.
Controls and Indicators
1
2
3
4
75 6 8 9 10 1211
BLUETOOTH indicator (Blue)
1
LINE IN indicator (Green)
2
USB indicator (Orange)
3
STAND BY indicator (Red)
4
LINE IN socket
5
USB port
6
VOLUME knob
7
BASS knob
8
TREBLE knob
9
Skip Forward/Backward button
10
Play/Pause/PAIR button
11
POWER/FUNCTION button
12
Speaker air hole
13
AC power socket
14
1413
Using this speaker
Listening to Bluetooth® Music
In order to use the unit for music playback or speakerphone functions through Bluetooth®,
the speaker must rst be paired with the Bluetooth® device.
Pairing:
Press the POWER/FUNCTION button on the speaker to switch to
1
Bluetooth® mode.
The Bluetooth® function will go into pairing mode and the blue indicator keep ashing.
Following the instructions in your device's user manual, activate
2
Bluetooth® on your device and search for devices.
Once you have found "TY-WSP67”, pair with the speaker.
• Input the pass code "0000" if required.
Once connected, a pairing successful sound is heard.
• The blue indicator of the speaker will remain lit.
Information:
• This speaker will pair with the last connected device when that device is in range.
• The Bluetooth® pairing can be canceled by pressing and holding the Play/Pause button
for more than 3 seconds. Then a canceling successful sound is heard.
• If there is n o operation or nothing is played ba ck in Bluetooth, USB, or LI NE IN mode for 30
minutes, the speaker will automatically go into standby mode.
Playing Bluetooth® Music:
Once your device and the speaker are paired, you can play music on this speaker through
Bluetooth®.
Press the Play/Pause button either on your device or this speaker to
1
play or pause music.
Use the VOLUME/BASS/TREBLE knob on this speaker to adjust the
2
level.
Turning o the power
Press and hold the POWER/FUNCTION button to turn o the speaker.
1
The standby indicator lights in red.
Playing line-in Music
You can connect an MP3 player or other portable audio device through this speaker via the
LINE IN socket.
Plug a 3.5 mm plug into the headphone or line-out jack on your
1
device and plug the other end of the cable into the LINE IN socket of
this speaker.
Press the POWER/FUNCTION button on the speaker to switch to LINE
2
IN mode.
The LINE IN indicator lights in green.
Turn on and play your device.
3
Adjust the volume level on your device or use the VOLUME knob on
4
this speaker.
170418c1_TY-WSP67_EN.indd 1 2017/04/18 11:15:52
Listening to a USB device
This speaker provides a USB port for music playback.
Press the POWER/FUNCTION button on the speaker to switch to USB
1
mode.
The USB indicator lights in orange.
Insert a USB memory stick in the USB port on the front of the speaker.
2
Use the VOLUME knob on this speaker to adjust the volume level.
3
Notes
• Press the Skip forward/Backward button during playback to skip the track forward. Press
and hold the button to skip the track backward.
• Press the Skip Forward/Backward button while paused to move to the nex t folder. Press
and hold the button to move to the previous folder.
Specifications
Blue tooth® section
Bluetooth® spec. Version 2.1
Wireless equipment
Classication
Supported prole A2 DP, AV RC P
Frequency range 2.402-2.480 GHz (2.4 GHz ISM Segment)
Service distance Up to 10 m
USB memor y section
Playback format MP3
Memory
Supported memory
Playable USB memory USB-IF certied product
General
Power supply AC 100-240 V~, 50/60 Hz
Power consumption 40 W
Max. output power 20 W X2 + 40 W
LINE IN input terminal 3.5 stereo mini-jack
Dimension 348 x 187 x 187 mm (W x H x D)
Speaker 25 mm 4 ohm 20 W x 2, 135 mm 4 ohm 40 W x 1
Accessories AC cord x 1, Operation manual x 1
This user manual may be changed without prior notice to improve product performance.
The images included in this guide may dier from the actual image and may change without
notice.
Class 2
32 MB to 32 GB
USB1.1 or USB2.0
Weight Approx. 4720 g
1-1-8, Sotokanda, Chiyoda-ku Tokyo 101-0021, Japan
170418c1_TY-WSP67_EN.indd 2 2017/04/18 11:15:52
Loading...