Guangzhou Liwei Beam 200W SHARPY 5R User Manual

Guangzhou Best Stage Light Equipment Co.’ Ltd

1

BEAM 200W SHARPY 5R

User Manual

Please read this user manual carefully before operate it

Guangzhou Best Stage Light Equipment Co.’ Ltd

2

At first , thanks for purchase our pro lighting products.

This user maunal include how to safely for installations and use of the important informations.

Please carefully read the requirements of installation and operation .

At the same time, please return this user manual properly preserved, for a rainy day.

The light is very good, humanization and industrial design perfect combination, attractive

appearance, fluent.The lamp body of aluminum alloy and high temperature resistant engineering

plastics design, good heat dissipation effect. Transmission mechanism adopts electronic positioning

technology.Products completely accord with CE standard, adopts the international standard DMX512

signal control.Widely used in televisions, DISCO, dance halls, night clubs and other indoor places and

outdoor performances.

This product when in the factory are performance in good condition and completely packed. So users

should strictly comply with this specification statement warnings and instructions, any damage caused

by misuse is not our company guarantee.If ignore this manual operation to fault and problem ，It is not

our responsible for the dealer. This user manual such as technical subject to change without prior

notice.

Safety warning information

Before the frist time to use it, Please check whether the damage in transit, if happen damages in

transit, please do not use this lamp, and please asap contact distributors or manufacturers.

Please don't install the lamp in the ordinary combustible material on the surface.Lamp should be

installed in the well ventilated place, and the distance of the wall to keep it over 10 cm, at the same

time, please check the fan hole was clear.

Do not use lamp direct project in flammable objects, lamp and the radiation of the distance between

the objects please keep it over 12 m.

Do not use direct lamp project light source , to avoid damage the eyes.

Before installation, please make sure your use power supply voltage and marked voltage

Note:before any install,maintain and clean lamp, please confirm cut off the power supply.

1.Operation

touch wheel function

Up turn left option/edit

down turn right option/edit

OK / Enter press the wheel

Executive start / exit

return when return menu ,press the wheel return previous page

Set ”Modify address code” as an example, tell about the using of the touch.

1. Touch button “setting” in the main interface, and then into “setting” interface.

2. The 4 touch button in the right, are “up”, “ok”, “down”, “back”.

3. Press “up” or “down” button select “DMX address”.

4. Press “ok” button into editing state.

5. Press “up” button or “ down” button modification address code (using the new address immediately

and autosave)

6.Press “OK” button out of the editing state ( could omitted)

7. Press “back” button back to the main menu.

If using the wheel, process like bellow :

1. In the main interface , turn the wheel, select “setting” button.

2. Press the turn wheel and then loosen, into “setting” interface.

3.In the “setting” interface, select “DMX address”

4. Press the turn wheel and then loosen, into the editing state.

5. Turn the wheel, modification address code

Guangzhou Best Stage Light Equipment Co.’ Ltd

3

6. After modification, press turn wheel and then loosen, out of the editing state.

7. Turn the wheel select “back”, press turn wheel and then loosen, back into the main interface.

2.Interface description

2.1 Main Interface

Top right corner 3 button for language switching and screen rotation
Bottom row four button corresponding sub interface is introduced, it’s in the back.
With touch operating mode sub interface is introduced, if use wheel, corresponding relation as
follows:
Press up : turn left
Press down : turn right
Press ok : press the wheel

Use wheel operation dialog box

If ok ,press the wheel.if cancel ,turn the wheel.（as above the display)

2.2 Set up the interface

Option instruction

Run Mode DMX

Slave state:Accept control table or main engine

Automatic

Statistics : Automatic operation and send DMX signal for slave

Note:If the bulb is put out before , the light bulb will not be full

light. If you need to observe the lighting effects, please keep the

light on，and then into the automatic state

DMX
Address

1-512

Press OK key into edit state, its selected hundred. Press up or

down,change address code.Press again OK key, selected ten

editor. Press again OK key, select the edit. Press it again to exit

the edit state.

Channel
Mode

16

The 17thto 20thchannels are invalid.

20

Control speed of the 17thto 20thchannels （see the channel list ）

Invert
Pan/Tilt

OFF
NO

Swap
Pan-Tilt

OFF
NO

Change the channel of XY axis （include trimming）

Encoder
Pan-Tilt

NO

Use encoder correct position

OFF

Do not use encoder correct position

No DMX
Signal

KEEP

According to the original state continues to run

CLEAR

The return of the motor, stop running

Guangzhou Best Stage Light Equipment Co.’ Ltd

4

Display
Power Save

NO

Free 30 seconds after closing backlight

OFF

Backlight ever bright

Burn on startupOFF

Power on directly after reset, no light bulb (need to use the menu

or control table to manual light bubble)

NO

After power on automatic light bubble, must wait for the light bulb

light up success can be reset

Load Default

Press ok key see the confirmation dialog box, again press ok key,

Press OK key into edit

2.3. Information interface

Option instruction

Total using time Cumulative using time (Accuracy to the minute)

The use of time Use of time since the boot (Accuracy to the minute)

System error logs

If the red indicator shine ,that mean the lamps runs error . The details can
be entered sub-interface to view

After you finish view,

you can press the "OK" key to make the error log empty. Pay attention:
Sometimes not the Hall or optical coupler installation problems, But the
motor cable is connected backwards

2.4. Manual control interface

T

his interface use to control present light, neither belong to the from the machine state (didn’t received
DMX signal), nor belong to Host state( send DMX signal).
option instruction

Reset Press ok key see the confirmation dialog box, again press ok key, enter the

reset interface, all motor reset.

Color wheel 0-255

Press OK key into edit state, its selected hundred. Press up
or down,change channel value .Press again OK key,
selected ten editor. Press again OK key, select the edit.
Press it again to exit the edit state.

…… 0-255

the speed of gobo
wheel

0-255

Blub control ON

OFF

2.5 Advanced

interface

Password is “Up down up down “ . For the runner , password is “Left right left right”