Guangde Ledup Enterprise T11801B1 User Manual
2018 Home Depot.com/US
7.5ft Starry Light Slim Frasier Fir Flocked Tree Instruction Sheet - 10 Function Remote (English)
Date: 5/3/18
18”
Item # SL75256SF-GP62F
Model No. 7STR4-1801B1
1 0 STR4-1801B1
0
6STR4-1801B1
15STR5-1801B1
4R4-170 1B1/ T
/
0
8R5-1801B1
ASSEMBLY INSTRUCTIONS
(We recommend wearing proper clothing in order to prevent
scratches that may occur during the assembly process.)
Carefully unpack the contents from the tree’s carton (Fig 1);
including the contents of the poly-bag that is adhered to the
interior flap of the tree’s carton.
Contained in the poly-bag is the remote control which
operates your tree's 10 function lighting capability.
Your tree should include the following components:
A folding metal tree stand with (3) eyebolts.
An on/off push button foot pedal with cord and plug (Fig 6);
which is pre-attached at the lowest section of your tree (Fig 5).
The 7.5’ tree will have (3) tree sections; (“A”, “B” and “C”; as
shown in Fig 5).
Fig 1
ASSEMBLY OF THE TREE STAND
1. Remove the tree stand from the plastic bag, loosen the eye
bolt and open the tree stand to form an “X”.
2. Align the holes for the insertion of the remaining (2) eyebolts.
3. Insert each eyebolt and begin threading in a clockwise
direction for a couple of rotations only; leaving enough room
for the tree’s pole from section “A” to be inserted into the
assembled stand (Fig 2).
4. Place the tree stand in its desired location; as once the tree is
fully assembled, it may be too difficult to move and relocate.
Fig 2
ASSEMBLY OF THE TREE
1. Locate the bottom section of the tree which is identified by
a label on the outer branches marked “A” (Fig 5).
2. Remove the protective plastic cap from the end of the pole,
(that is pinched to a point), and place that end into the tree
stand. Be sure that the pointed end of the pole extends to
the bottom of the stand.
3. Now tighten the eyebolts evenly on the tree stand; being
careful not to over-tighten (Fig 3).
Fig 3
CCT18
4. Carefully cut the nylon strapping bounding the branches
upright.
CAUTION: Be extremely careful not to cut any of the exposed
light set wires.
5. Now gently guide the branches downward into place.
6. Beneath the canopy of section “A”, contain’s an on/off push
button foot pedal with cord and plug (Fig 6).
Remove the twist-tie binding the cord together and insert the
plug into a working electrical outlet.
7. On/off push button foot pedal operation:
The on/off push button foot pedal is intended to provide basic
manual on/off operation only; and therefore cannot provide
the remote control’s 10 function lighting capability.
NOTE: If the tree is powered off by the use of the push
button foot pedal, remote control or by unplugging it from
the electrical outlet; when powered back on the tree will
resume the memory of the last lighting function selected
with the remote control.
EZ-POWER™ TECHNOLOGY
NOTE: Your tree has been designed with EZ-Power™
technology; allowing for each of the tree’s remaining sections
to light up automatically, upon a firm insertion of each
lettered section (Fig 5).
8. Locate the next section of the tree which is identified by a
label on the outer branches marked “B” (Fig 5).
9. Remove the protective plastic cap from the end of the pole
on section “B”; insert that end onto the top of the pole of
section “A” (Fig 4).
Fig 4
10. Once section “B” is fully inserted downward into section “A”;
both section “A” and section “B” will now be lit.
11. Again, carefully cut the nylon strapping bounding the
branches upright; being extremely careful not to cut any of
the exposed light set wires.
12. Now gently guide the branches of section “B” downward into
place.
13. Depending on the height of the tree you have purchased,
you will continue to build your tree upwards, section by
section, following the above steps until the tree is completely
assembled. Each section of the tree is labeled in alphabetical
order beginning from the bottom to the top.
Fig 5
C
B
A
Foot
Pedal
Fig 6
REMOTE CONTROL OPERATION
Included is the remote control that operates the colors and
functions of your LED pre-lit and pre-shaped Christmas tree (Fig 7).
Fig 7
Before operation; three standard AAA batteries (R03 or LR03) must
be installed into the remote control; by simply removing the slide
plate located on the back of the remote control.
The LED pre-lit and pre-shaped Christmas tree’s 10 lighting
function capability is controlled solely by the use of the remote
control provided.
NOTE: By reducing the distance from your tree; you may achieve
better remote control reception.
By pressing the Function or ON/OFF button on the remote
control; indicator lights will keep you on track as to the exact
color and function that you are currently on.
By pressing your function buttons up or down on your remote
you can choose between the following 10 Functions:
Demo
Steady Warm White
Steady Icy Multi
Slow Fade Warm White
Slow Fade Icy Multi
Twinkle Warm White
Twinkle Icy Multi
Fast Flip Warm White to Icy Multi
Slow Flip Warm White to Icy Multi
Slow Fade Warm White to Icy Multi
6H Timer:
The timer button is located on the right side of the remote. When
set to the "on" mode, the lights will flash Warm White 3 times
indicating that the 6 hour timer has been activated. The tree will
now remain on for 6 hours and will automatically resume the last
function 18 hours after shut off. To turn off the timer, simply set to
"off" mode. The lights will flash Warm White 1 time.
If the tree is manually turned off while the timer is set, the timer
will shut off. If the tree is powered back on and the timer button is
still set to on, the timer will reactivate at that point and remain on
for 6 hours.
TROUBLESHOOTING
1. If the tree does not illuminate press the on/off button on your
remote control. If failure to light persists, the battery may need to
be replaced. Insert three standard AAA type batteries (R03 or LR03);
aligning the appropriate ( +/- ) markings accordingly.
NOTE: The tree’s 10 function lighting capability is controlled solely
by the use of the remote control provided.
If the tree fails to light due to a damaged or defective remote
control; please resort to manual on/off push button foot pedal
operation until a new remote control can be provided through our
customer service center.
2. If failure to light persists, press the on/off push button foot pedal; as
it may be in the “Off” mode.
3. If the top of the tree or another individual lettered section does not
illuminate, remove each section and then reinsert as instructed, to
ensure the electrical connection is made.
NOTE: The tree’s top is designed specifically for a secure and firm
connection point. Downward force will be needed to ensure that
the electrical connection occurs.
NOTE: A SPECIALTY NON-REPLACEABLE LED HAS BEEN
APPLIED TO YOUR PRE-LIT TREE; IN THE CASE THAT A
INDIVIDUAL LED BULB BURNS OUT, THE REMAINING LED BULBS
WILL CONTINUE TO STAY LIT.
DISASSEMBLY & STORAGE
1. Gently remove the plug from its electrical outlet, and carefully bind
the cord which contains the on/off push button foot pedal and plug.
2. Beginning with the tree’s top section; lift each section straight up
from the section below, and continue working downward.
NOTE: You may have to slightly wiggle each section as you lift each
section upward.
3. To remove the bottom and final section; loosen the eyebolts by
turning in a counter-clockwise direction and lift section “A” from the
support collar of the tree stand.
4. Gently fold the branches of each section upward, towards the
center, and position in the storage container.
NOTE: With the exception of the tree’s “top” section; by holding
each section upside down; the branches will collapse downward,
due to the hinging, aiding in the packing of each section into the
storage container.
5. Fully unthread the eyebolts from the tree’s stand and fold together;
placing in the storage container.
6. It is recommended to always store the tree in a cool, dry location
protected from excessive exposure to heat or sunlight.
Store your remote control in a SAFE & DRY location and
remove the battery from remote control before storage.
NOTE: ALTHOUGH THE LED LIGHT STRINGS ON THE TREE ARE
RATED FOR INDOOR OR OUTDOOR USE; THE COMBINATION OF THE
TREE WITH THE LED LIGHTS IS FOR INDOOR USE ONLY.
FLOCKING OR GLITTER DISCLAIMER
Notice: Your pre-lit tree has been professionally flocked or
glittered.
Upon the tree sections being removed from its carton, you will notice
an accumulation of flocking or glitter at the base of the carton.
Do not be alarmed.
This loose flocking or glitter material was accounted for and
planned in the packing and manufacturing process of this tree.
In no way has the appearance or the integrity of the tree's
quality been compromised.
During future Holiday seasons you can expect a light dusting of
flocking or glitter to loosen from your tree during the packing and
unpacking process. Extra flocking or glitter has been adhered to
your tree to account for this minor annual loss.
The overall beauty of your tree will not be diminished.
Simply sweep or vacuum up the loose flocking or glitter upon the
assembly completion. During the flocking or glitter process the
light bulbs themselves have been flocked or glittered. This was
purposely done for the overall lighting effect of the tree.
PLEASE NOTE: Your flocked tree must NOT be stored in a plastic
bag or bags as moisture and condensation may occur, causing for
the discoloration of the flocking material.
Your flocked or glittered tree must be stored in a cool and dry location
protected from excessive exposure to moisture, heat or sunlight.
With proper care and proper storage location, you will experience
many years of enjoyment.
This product was pre-tested before shipment and date
coded. In keeping with the National Electric Code, this
product is intended for seasonal (90 days max.) installation
and use. For problems or questions on this product call our
customer service toll-free at 1-877-527-0313.
Made in China
Printed in China
This is not a toy, for decorative use only.
DISTRIBUTED BY HOME DEPOT U.S.A., INC. 2455
PACES FERRY RD., N.W. Atlanta, GA 30339 All rights reserved.
15”
Loading...