GTO Pro SL-1000, Pro SL-2000 Installation Manual

Download

Page 1

AUTOMA TIC GATE OPERA TOR

FOR VEHICULAR SLIDE GATES

INSTALLATION MANUAL FOR THE PROFESSIONAL INSTALLER

Safety Edge

(REQUIRED)

Chain Bracket

Chain

Safety Edge

(REQUIRED)

WARNING

Moving Gate Can Cause

Injury Or Death

1.KEEP CLEAR! Gate may move at any time.

2.Do not allow children to operate gate or play in gate area.

3.This gate is for vehicles only. Pedestrians must use a separate entrance.

Roller Guard

(REQUIRED)

WARNING!

Roller Guard

(REQUIRED)

Chain Bracket

®

CAUTION

AUTOMATIC GATE

STAND CLEAR

1-800-543-GATE

PRO-SL-2000

Operator

Use PVC Conduit  (not included)

for power cables. 

Safety Edge

(REQUIRED)

Run 1000' (max.) of low voltage wire to control box from transformer (wire not included).

Receiver (cable in separate conduit)

120 Volt Indoor Transformer

(Surge Protector

not supplied)

Roller Guard

(REQUIRED)

• READ ALL INSTRUCTIONS COMPLETEL Y before attempting installation

and use; failure to do so may result in serious injury or death.

• This unit must only be installed by an experienced technician!

• Operator power must be disconnected before servicing!

• This gate operator produces a high level of force. Stay clear of the unit while it is operating and exercise caution at all times.

This product meets and exceeds the requirements of UL 325, the standard which regulates gate operator safety, as

established and made effective March 1, 2000, by Underwriters Laboratories Inc.

DO NOT INSTALL THIS OPERATOR WITHOUT SAFETY EDGES AND ROLLER GUARDS!

3121 Hartsfield Road • Tallahassee, Florida, USA 32303

Telephone (800) 543-GATE or (850) 575-0176 • Fax (850) 575-8912 • www.gtoinc.com

RB270 rev - 09/25/01

Page 2

GTO PRO SL-1000 and SL-2000 series automatic gate operators are intended for use with vehicular slide gates. These operators can be used in Class I, Cass II and Class III applications.

VEHICULAR GATE OPERATOR CLASS CATEGORIES

Residential Vehicular Gate Operator-Class I: A vehicular gate operator (or system) intended for

use in a home of one-to-four single family dwelling, or a garage or parking area associated therewith.

Commercial/General Access Vehicular Gate Operator-Class II: A vehicular gate operator (or system) intended for use in a commercial location or building such as a multifamily housing unit (five or more single family units), hotel, garages, retail store, or other building servicing the general public.

Industrial/Limited Access Vehicular Gate Operator–Class III: A vehicular gate operator (or system) intended for use in an industrial location or building such as a factory or loading dock area or other locations not intended to service the general public.

Restricted Access Vehicular Gate Operator–Class IV: A vehicular gate operator (or system) intended for use in a guarded industrial location or building such as an airport security area or other restricted access locations not servicing the general public, in which unauthorized access is prevented via supervision by security personnel.

Conversion Chart

Converting Metric Units to English Equivalents

When Y ou Know Multiply By T o Find Symbol

centimeters 0.3937 inches in. (or ") meters 3.2808 feet ft. (or ') kilograms 2.2046 pounds lb. (or #)

Converting English Units to Metric Equivalents

When Y ou Know Multiply By T o Find Symbol

inches 2.5400 centimeters cm feet 0.3048 meters m pounds 0.4535 kilograms kg

Temperature

deg. Celsius (ºC x 1.8) + 32 deg. Fahrenheit ºF deg. Fahrenheit (ºF-32) / 1.8 deg. Celsius ºC

Page 3

TABLE OF CONTENTS

Gate Operator Class Categories -------------------------------------------------------- inside cover Important Safety Instructions ----------------------------------------------------------- page 1

Important Safety Instructions for the System Designer---------------------------- page 2 Important Safety Instructions for the Installer -------------------------------------- page 2 Secondary means of Protection Against Entrapment------------------------------- page 4 Important Safety Instructions for the Consumer/End User------------------------ page 5 Warning Labels and Signs ------------------------------------------------------------- page 7

Technical Specifications for SL-1000--------------------------------------------------- page 9 Technical Specifications for SL-2000--------------------------------------------------- page 10

Parts Identification (Single Gate Operator) ------------------------------------------ page 11 Single Gate Operator Installation ------------------------------------------------------ page 12

Overview and Gate Preparation ------------------------------------------------------- page 12 Suggested Conduit & Wiring and Mounting the Legs ----------------------------- page 13 Determining the Mounting Position and Mounting the Operator ---------------- page 14 Installing the Chain --------------------------------------------------------------------- page 15 Disconnecting Operator Chain for Manual Operation of Gate ------------------- page 15

Powering the System ---------------------------------------------------------------------- page 16

Maximum Operational Cycles Chart ------------------------------------------------- page 16 Installation of the Transformer -------------------------------------------------------- page 16

Control Board settings -------------------------------------------------------------------- page 20 DIP Switches --------------------------------------------------------------------------------- page 20 Potentiometers ------------------------------------------------------------------------------- page 21

Connecting the Receiver to the Control Board -------------------------------------- page 22 Setting Your Personal Transmitter Code ------------------------------------------------- page 22 Mounting the Receiver---------------------------------------------------------------------- page 23

Adjusting the Limit Switches ------------------------------------------------------------ page 24 Connecting Safety Devices --------------------------------------------------------------- page 25 Connecting Accessories ------------------------------------------------------------------- page 27 Maintenance & Troubleshooting-------------------------------------------------------- page 29 Warranty and Repair Information ----------------------------------------------------- page 32 Dual Gate System Installation----------------------------------------------------------- page 33

Preparing the Gates --------------------------------------------------------------------- page 35 Wiring the Second Operator ----------------------------------------------------------- page 36 Setting the Control Board for Dual Gate Installations ----------------------------- page 37

Accessory Catalog-------------------------------------------------------------------------- page 39 Installation Check List -------------------------------------------------------- inside back cover

Page 4

IMPORTANT SAFETY INSTRUCTIONS

FOR THE GTO/PRO SL-1000/2000 AND GTO/PRO SL-1000B/2000B

AUTOMATIC SLIDE GATE OPERATORS

Because automatic gate operators produce high levels of force, all system designers, installers, and consumers have an obligation to know the potential hazards associated with improperly designed, installed, or maintained gate operator systems. Keep in mind that the gate operator is just one component of the total gate operating system. Each component must work in unison to provide the consumer with convenience, security, and safety.

This manual contains various safety precautions and warnings for the system designer, installer, and consumer. Because there are many possible applications of the gate operator, the safety precautions and warnings contained in this manual cannot be completely exhaustive in nature. They do, however, provide an overview of the safe design, installation, and use of this product. CAREFULLY READ AND FOLLOW ALL SAFETY PRECAUTIONS,

WARNINGS, AND INSTALLATION INSTRUCTIONS TO ENSURE THE SAFE SYSTEM DESIGN, INSTALLATION, AND USE OF THIS PRODUCT.

The precautions and warnings in this manual are identified with this warning symbol. The symbol identifies the conditions that can result in damage to the operator or its components, serious injury,

or death.

Because GTO automatic gate operators are only part of a total gate operating system, it is the responsibility of the designer, installer, and purchaser to ensure the total system is safe for its intended use. Bypassing safety devices or neglecting to use safety devices with the gate operator is NOT acceptable.

TO MANUALLY OPEN AND CLOSE THE GATE, FOLLOW THE PROCEDURE BELOW :

CAUTION: Disconnect the operator chain ONLY when the gate is NOT moving.

1. Lift the quick release pins UP, then pull them OUT of the chain brackets (see illustration).

2. Lay the chain down and manually slide the gate to the desired position.

Chain Bracket

Quick Release Pin

To prevent unauthorized removal of the quick release pins, install Master® pin locks (see accessory catalog) above the quick release pins in both chain brackets.

Page 5

IMPORTANT SAFETY INSTRUCTIONS

FOR THE SYSTEM DESIGNER

WARNING: To reduce the risk of injury or death:

1. READ AND FOLLOW ALL INSTRUCTIONS.

2. This operator is intended for use only vehicular gates. Pedestrians must be supplied with a separate walk-

through gate (see Entrapment Protection on page 6).

3. When designing a system that will be entered from a highway or main thoroughfare, make sure the system is placed far enough from the road to prevent traffic congestion.

FOR THE INSTALLER

WARNING-To reduce the risk of injury or death:

I. Before Installation

1. READ AND FOLLOW ALL INSTRUCTIONS.

2. Verify this operator is proper for the type and size of gate, and its frequency of use.

3. Make sure the gate has been properly installed and slides freely in both directions. Repair or replace all worn or damaged gate hardware prior to installation. A freely moving gate will require less force to operate and will enhance the performance of the operator and safety devices used with the system.

4. All openings of a horizontal slide gate must be guarded or screened to prevent a 21/4 inch diameter sphere from passing through openings anywhere in the gate. This screen (or guard) must also be installed over the portion of adjacent fence that the gate covers in the open position (see page 6).

5. Review the operation of the system and become familiar with its safety features. Understand how to disconnect the operator chain with the quick release pins for manual operation of the gate (see page 1).

6. This gate operator is intended for vehicular gates ONLY. A separate entrance or gate must be installed for pedestrian use (see page 6). NO ONE SHOULD CROSS THE PATH OF A MOVING GATE.

II. During Installation

1. Install the gate operator on the inside of the property and fence line. DO NOT install an operator on the outside of the gate where the public has access to it.

2. Be careful with moving parts and avoid close proximity to areas where fingers or hands could be pinched.

3. Determine the best obstruction sensing setting for this installation. The gate MUST stop and reverse on contact with an obstruction or when an object activates the non-contact sensors. After adjusting the force or the limit of travel, retest the gate operator. Failure to adjust and retest the gate operator properly

increases the risk of injury or death.

4. Additional safety equipment such as roller guards and safety edges (or photoelectric sensors) MUST be installed to prevent bodily injury (see page 6).

5. Mount access controls away from the gate (minimum distance is 10 feet). The user must have full view of the gate but be unable to touch it while operating the controls.

Page 6

IMPORTANT SAFETY INSTRUCTIONS

6. Secure outdoor or easily accessed gate operator controls in order to prohibit unauthorized use of the gate.

III. After Installation

1. Review ALL safety instructions with the consumer/end user and explain the basic operation and safety systems of the entire gate operator system, including disconnecting the chain for manual gate operation.

2. Inform the consumer/end user that servicing of the operator must only be done by an experienced technician.

3. Attach the warning signs (included) to each side of the gate to alert public of automatic gate operation. Take a photo of warning signs installed on gate. Record the date of the photo for your reference.

4. SAVE THESE INSTRUCTIONS. Leave IMPORTANT SAFETY INSTRUCTIONS

(included) with consumer/end user.

Page 7

IMPORTANT SAFETY INSTRUCTIONS

STATUS

BATT

PWR. SW.

SECONDARY MEANS OF PROTECTION AGAINST ENTRAPMENT

As specified by Underwriters Laboratories Inc. UL 325 (30A.1.1), automatic gate operators shall have provisions for, or be supplied with, at least one independent primary and one independent secondary means to protect against

entrapment. GTO gate operators utilize Type A, an inherent entrapment sensing system, as the primary type of entrapment protection. The GTO/PRO SL-1000/2000 and GTO/PRO SL-1000B/2000B gate operators have provisions for the connection of Type B1 and B2 protection to be used as the secondary type of entrapment protection.

1. For gate operators utilizing a non-contact sensor (Type B1) in accordance with UL 325 (51.8.4 [h]): A. Refer to the sensor manufacturer’s instructions on the placement of non-contact sensors for each type of

application. B. Care shall be exercised to reduce the risk of nuisance tripping, such as when a vehicle trips the sensor while the gate is still moving. C. One or more non-contact sensors shall be located where the risk of entrapment or obstruction exists, such as the perimeter reachable by a moving gate or barrier.

2. For gate operators utilizing a contact sensor (Type B2) in accordance with UL 325 (51.8.4 [i]): A. One or more contact sensors shall be located at the leading edge, trailing edge, and post mounted both inside

and outside of a vehicular slide gate system. B. A hard wired contact sensor shall be located and its wiring arranged so that the communication between the sensor and the gate operator is not subjected to mechanical damage. C. A wireless contact sensor such as one that transmits radio frequency (RF) signals to the gate operator for entrapment protection functions shall be located where the transmission of the signals are not obstructed or impeded by building structures, natural landscaping or similar obstruction. A wireless contact sensor shall function under the intended end-use conditions.

ENTRAPMENT ALARM (UL 325; 30A.1.1A)

The GTO/PRO SL-2000 and GTO/PRO SL-2000B operators are designed to stop and reverse for 2 seconds when the gate comes in contact with an obstruction or when an object activates the non-contact sensors. Additionally, these operators are equipped with an audio entrapment alarm which will function if the unit obstructs twice while opening or closing. This alarm will sound for a period of 5 minutes or until the operator receives an intended signal (e.g., transmitter signal) and the gate returns to a fully open or fully closed position.

–

Entrapment Alarm

(bottom right of control box)

Page 8

IMPORTANT SAFETY INSTRUCTIONS

FOR

WARNING: To reduce the risk of injury or death:

1. READ AND FOLLOW ALL INSTRUCTIONS.

2. Distribute and discuss copies of the IMPORTANT SAFETY INSTRUCTIONS manual with all persons authorized to use your gate. SAVE THESE INSTRUCTIONS.

3. Always keep people and objects away from the gate and its area of travel.

NO ONE SHOULD CROSS THE PATH OF THE MOVING GATE.

4. Your automatic gate is not for pedestrian use. If pedestrian traffic is expected near the gate, a walk-through gate must be installed for this purpose (see page 6).

5. Do not allow children or pets near your gate. Never let children operate or play with gate controls. Keep the remote controls away from children and unauthorized users; store controls where children and unauthorized users cannot access them.

6. If push buttons or key switches are installed, they should be within sight of the gate, yet located far enough from the gate (at least 10 feet) so the gate cannot be touched while in operation. Do not operate any control without watching the movement of the gate.

7. Do not activate your gate operator unless you can see it and can determine that its area of travel is clear of people, pets, or other obstructions.

THE CONSUMER/END USER

8. If your gate has open rollers, be sure that roller guards have been installed to prevent hands and fingers from being caught in the rollers (see page 6).

9. It is your responsibility to make sure that the installer posted warning signs on both sides of your gate. If any of these signs or warning decals become damaged, illegible or missing, replace them immediately. Contact your installer or GTO for replacements.

10. Verify that electric safety edge sensors (or photoelectric sensors) have been installed (see page 6). These safety devices should be tested monthly.

11. KEEP GATES PROPERLY MAINTAINED. Have a qualified service person make repairs to the gate hardware. NEVER REMOVE THE OPERATOR HOUSING.

12. DO NOT attempt to service this operator yourself; for service, contact your installer or another experienced technician.

13. Have your gate operator tested monthly and serviced regularly by an experienced technician. The gate MUST stop and reverse on contact with an obstruction or when an object activates the non-contact sensors. If these functions are observed to operate improperly, discontinue use and have operator serviced immediately.

14. To operate this equipment safely, YOU must receive detailed instructions on disconnecting the operator chain with the quick release pins (see page 1). If you feel you have not received full and proper instructions, contact your installer.

15. Disconnect the operator chain ONLY when the gate is NOT moving.

Page 9

IMPORTANT SAFETY INSTRUCTIONS

REQUIRED SAFETY PRECAUTIONS FOR GATES

INSTALL SCREEN GUARD OVER GATE AND FENCE

Injuries may occur when people place their hands, arms, legs, etc., through openings in the gate grill when the gate is operated, trapping them between the grill and the fence post (or fence). All openings of a horizontal slide gate must be guarded or screened to prevent a 2 This screen/guard must also be installed over the portion of adjacent fence that the gate covers in the open position. Screening will prevent access through openings in areas where the gate may travel.

Safety Edge

Screen Mesh

/4” diameter sphere from passing through openings anywhere in the gate.

Safety Edge Safety Edge

Roller guard to prevent pinch point hazard.

Safety Edge

ROLLER GUARDS

Injuries occur when people get their hands caught between the gate and the roller. Roller guards and enclosed tracks must be installed to prevent this pinch point hazard.

WARNING

Moving Gate Can Cause

Injury Or Death

1. KEEP CLEAR! Gate may move at any time.

2. Do not allow children to operate gate or play in gate area.

3. This gate is for vehicles only. Pedestrians must use a separate entrance.

WARNING SIGNS

The warning signs (above right) must be installed on both sides of the gate (see page 7 for details).

Roller guard to prevent pinch point hazard.

ENTRAPMENT PROTECTION GTO’s internal obstruction settings, even when properly adjusted, may not be sensitive enough to prevent bodily injury. For this reason, safety devices such as safety edges MUST be installed. Furthermore, a walk-through gate

must be installed if pedestrian traffic is expected near the gate. We recommend the GTO Bulldog Pedestrian Gate Lock (see accessory catalog) for controlled access.

Pedestrian Gate

Safety Edge

Warning Sign

Safety Edge

Roller Guard

Moving Gate Can Cause

1.KEEP CLEAR! Gate may move at any time.

2.Do not allow children to operate gate or

3.This gate is for vehicles only. Pedestrians

Vehicle Gate

WARNING

Injury Or Death

play in gate area.

must use a separate entrance.

Roller Guard

CAUTION

AUTOMATIC GATE

STAND CLEAR

1-800-543-GATE

Operator

Page 10

IMPORTANT SAFETY INSTRUCTIONS

These warning labels should be found at the locations specified below. If any of them are missing, immediately contact your installer for replacements.

WARNING

• Fingers, hands, and loose clothing may be dragged into chain sprockets.

• Fingers and hands can be injured by rotating sprockets.

• Keep hands, fingers, and loose clothing away from chain and chain opening in operator housing.

warning labels (3) located on sides and back of operator housing

Conforms to UL 325 STANDARDS

Certified to CAN/CSA-C22.2 No.247-92

''%&

Disconnect operator ONLY when the gate is NOT moving.

TO MANUALLY OPEN AND CLOSE THE GATE:

1. Lift quick release pins UP, then pull them OUT of chain brackets.

2. Lay chain down and manually slide gate to desired position.

75+

Maximum Gate: 500 lb. (226.7 kg); 30 ft. (9.1 m) Voltage: 12 Vdc; Frequency: 0 Hz; Power: 93.2 W Class I, II and III Vehicular Slide Gate Operator Serial Number: SL1000-xxxxxxx

GTO, Inc. Tallahassee, Florida USA

Series

RB2001

WARNING

•Moving parts inside are capable of causing injury to fingers and hands.

•DO NOT remove operator housing.

•Consult your safety manual before making adjustments.

•

For service, call an experienced technician.

AUTOMATIC GATE OPENERS 1-800-543-GATE

warning label located on front of operator housing

WARNING

•Fingers, hands, and loose clothing may be dragged into chain sprockets.

•Fingers and hands can be injured by rotating sprockets.

•

Keep hands, fingers, and loose clothing away from chain and sprockets.

warning label located on top of control box

Conforms to UL 325 STANDARDS

Certified to CAN/CSA-C22.2 No.247-92

''%&

Disconnect operator ONLY when the gate is NOT moving.

TO MANUALLY OPEN AND CLOSE THE GATE:

1. Lift quick release pins UP, then pull them OUT of chain brackets.

2. Lay chain down and manually slide gate to desired position.

75+

Maximum Gate: 1000 lb. (453.4 kg); 30 ft. (9.1 m) Voltage: 12 Vdc; Frequency: 0 Hz; Power: 93.2 W Class I, II and III Vehicular Slide Gate Operator Serial Number: SL2000-xxxxxxx

GTO, Inc. Tallahassee, Florida USA

product identification and manual operation instruction label installed on control box cover

Series

RB2002

Page 11

IMPORTANT SAFETY INSTRUCTIONS

Continued from page 7

These warning labels should be found at the locations specified below. If any of them are missing, immediately contact your installer for replacements.

WARNING

•Fingers, hands, and loose clothing may be dragged into chain sprockets.

•Fingers and hands can be injured by

WARNING

Moving Gate Can Cause

warning sign located (inside housing) over the top sprocket at back of operator

rotating sprockets.

•Keep hands, fingers, and loose clothing away from chain and sprockets.

• Adjusting limit switches with power on will

• Injury may result if fingers get caught under

•

WARNING

activate gate. switch plate while adjusting switches.

Use extreme caution when adjusting switches.

Injury Or Death

1. KEEP CLEAR! Gate may move at any time.

2. Do not allow children to operate gate or play in gate area.

3. This gate is for vehicles only. Pedestrians must use a separate entrance.

warning signs (2) to be installed on each side of the gate (3–5 feet above the bottom of the gate)

WARNING

• Fingers, hands, and loose clothing may be dragged into chain sprockets.

• Fingers and hands can be injured by rotating sprockets.

• Keep hands, fingers, and loose clothing away from chain and sprockets.

warning label located on limit switch plate

warning label located (inside housing) next to sprockets on back of operator

Page 12

GTO PRO SL-1000 SERIES TECHNICAL SPECIFICATIONS

DRIVE

• Powered by a 12 V motor with integral case hardened steel gear reduction to 90 rpm. Generates 155 in. lb. of torque at 12

V. Motor temperature range -30 °F to +160 °F.

•Gate velocity: 1 ft/s.

POWER

• The PRO SL-1000 system is powered by a 12 Vdc, 7.0 Ah, sealed, rechargeable battery.

•Battery charge for PRO SL-1000 is maintained by a 18 Vac (40 VA) transformer rectified to 14.5 Vdc through the GTO

Control Board. Two (2) blade-style control board fuses rated for 15 A.

NOTE: The transformer should not be connected directly to any battery. Transformer must be connected with a minimum of 16 gauge, multi-stranded, dual conductor, direct burial low voltage wire. NOTE: Do not replace fuses with higher ampere rated fuses; doing so will void the warranty and may damage the control board.

•Battery charge maintained by GTO Solar Panel Charger: float voltage 14.5 Vdc output from a

193/8" x 151/4" silicon alloy panel. Generates minimum of 10 W at 600 mA. Gated diode on the control board prevents battery discharge.

CONTROL

• GTO microprocessor controlled board with temperature compensated circuits. Auto-memorization of digital transmitter

code. Charging regulated by circuit on control board. "Sleep draw" is 40 mA; "active draw" is 2 to 5 A.

• GTO remote-mounted RF receiver tuned to 318 MHz.

• Limit controls are mechanical. Normally open contact.

•Adjustable auto-close timer (OFF to 120 s), inertia, and obstruction sensitivity using three (3)

potentiometers.

• Power terminal block accommodates a transformer and solar panels.

•Operator terminal blocks accommodate safety edges and photoelectric sensors for opening and closing modes.

• Fully compatible accessory terminal block provides connections for safety loops, wands, intercoms, card readers, phone systems, etc.

•DIP switches simplify setup of gate operator.

• audio entrapment alarm sounds if unit obstructs twice while opening or closing.

OPERATIONAL CAPACITY

• The GTO/PRO SL-1000 and GTO/PRO SL-1000B will handle gates weighing up to 500 lb. (226.7 kg) and up to 30 ft. (9.14 m) in length (per leaf) if the proper installation procedures have been followed. Note that ball bearing rollers and

covers should be used on all gates.

• The GTO/PRO SL-1000 series operators are capable of continuous duty cycling; however, the total cycles per day will depend on the motor current and efficiency of the gate installation (see chart below). For questions relating to specific applications and for information regarding cycling duty when charged by solar panels, call the GTO Service Department at (800) 543-GATE [4283].

Gate Capacity Chart for SL-1000 Series

(estimated number of cycles based on use with a transformer)

20 ft. 16 ft. 12 ft.

8 ft.

Gate Length

120 140 160 180

200 lb.

Gate Weight

110 130 150 170

300 lb.

100 120 140 160

400 lb.

500 lb.

90 110 130 150

Cycles shown are for single gate, dual gates will get approximately half as many cycles.

Housing Dimensions: Height: 18" W idth: 211/2" Depth: 11"

Shipping W eight: Approximately 90 lb.

Rollers should be lubricated at least four times per year.

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.

Page 13

GTO PRO SL-2000 SERIES TECHNICAL SPECIFICATIONS

DRIVE

• Powered by a 12 V motor with integral case hardened steel gear reduction to 90 rpm. Generates 310 in. lb. of torque at 12

V. Motor temperature range -30 °F to +160 °F.

•Gate velocity: 1 ft/s.

POWER

• The PRO SL-2000 system is powered by a 12 Vdc, 7.0 Ah, sealed, rechargeable battery.

•Battery charge for PRO SL-2000 is maintained by a 18 Vac (40 VA) transformer rectified to 14.5 Vdc through the GTO

Control Board. Two (2) blade-style control board fuses rated for 20 A.

•Battery charge maintained by GTO Solar Panel Charger: float voltage 14.5 Vdc output from a

193/8" x 151/4" silicon alloy panel. Generates minimum of 10 W at 600 mA. Gated diode on the control board prevents battery discharge.

CONTROL

• GTO microprocessor controlled board with temperature compensated circuits. Auto-memorization of digital transmitter

code. Charging regulated by circuit on control board. "Sleep draw" is 40 mA; "active draw" is 5 to 13 A.

• GTO remote-mounted RF receiver tuned to 318 MHz.

• Limit controls are mechanical. Normally open contact.

•Adjustable auto-close timer (OFF to 120 s), inertia, and obstruction sensitivity using three (3)

potentiometers.

• Power terminal block accommodates a transformer and solar panels.

•Operator terminal blocks accommodate safety edges and photoelectric sensors for opening and closing modes.

• Fully compatible accessory terminal block provides connections for safety loops, wands, intercoms, card readers, phone systems, etc.

•DIP switches simplify setup of gate operator.

• audio entrapment alarm sounds if unit obstructs twice while opening or closing.

OPERATIONAL CAPACITY

• The GTO/PRO SL-2000 and GTO/PRO SL-2000B will handle gates weighing up to 1000 lb. (453.4 kg) and up to 30 ft. (9.14 m) in length (per leaf) if the proper installation procedures have been followed. Note that ball bearing rollers and

covers should be used on all gates.

• The GTO/PRO SL-2000 series operators are capable of continuous duty cycling; however, the total cycles per day will depend on the motor current and efficiency of the gate installation (see chart below). For questions relating to specific applications and for information regarding cycling duty when charged by solar panels, call the GTO Service Department at (800) 543-GATE [4283].

Gate Capacity Chart for SL-2000 Series

(estimated number of cycles based on use with a transformer)

20 ft. 16 ft. 12 ft.

8 ft.

Gate Length

80 100 120 140

400 lb.

Gate Weight

90 110 130

600 lb.

80 100 120

800 lb.

1000 lb.

50 70 90

110

Cycles shown are for single gate, dual gates will get approximately half as many cycles.

Housing Dimensions: Height: 18" W idth: 211/2" Depth: 11"

Shipping W eight: Approximately 90 lb.

Rollers should be lubricated at least four times per year.

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.

Page 14

PARTS IDENTIFICATION

Operator

Control Box with Control Board and Battery

Receiver

Operator Housing

32’ Drive Chain

(2) Chain Brackets

(2) 2” square x 48” long legs

(4) 3/8” Lock Washers

(4) 3/8” Nuts

18 Vac Transformer

”-16 x 2”

(4)

diameter U-Bolts

(8) 3/8” Serrated Nuts

GTO Transmitter

(4) 1/4”-20 x 1/2” Screws

(2) Chain Master Links

(4) 3/8” -16 x 3” Carriage Bolts

(2) Quick Release Pins

Page 15

SINGLE GATE OPERATOR INSTALLATION

GATE PREPARATION

Be sure the gate is properly installed and slides smoothly before installing the GTO/PRO Slide Gate Operator. The gate must be plumb, level, and move freely. The gate must not bind or drag on the ground. Never use a wheel

on the gate, because the additional drag and resistance can cause the operator to obstruct.

Level

Plumb

Concrete

OVERVIEW OF OPERATOR INSTALLATION

The diagram below shows a single slide gate installation with recommended safety features. The operator must be installed on the inside of the gate. GTO requires using safety edges and roller guards to help reduce the possibility

of bodily injury.

Safety Edge

(REQUIRED)

Chain Bracket

Safety Edge

(REQUIRED)

WARNING

Moving Gate Can Cause

Injury Or Death

1.KEEP CLEAR! Gate may move at any time.

2.Do not allow children to operate gate or play in gate area.

3.This gate is for vehicles only. Pedestrians must use a separate entrance.

Roller Guard

(REQUIRED)

Chain Bracket

®

CAUTION

AUTOMATIC GATE

STAND CLEAR

1-800-543-GATE

PRO-SL-2000

Operator

Safety Edge

(REQUIRED)

Receiver (cable in separate conduit)

120 Volt Indoor Transformer

(Surge Protector

not supplied)

Chain

Roller Guard

(REQUIRED)

Use PVC Conduit  (not included)

for power cables. 

Roller Guard

( RE Q UI R ED )

Run 1000' (max.) of low voltage wire to control box from transformer (wire not included).

Page 16

RECOMMENDED WIRING AND USE OF CONDUIT

Run the low voltage wire and receiver wire through PVC conduit into the slider unit to protect it from lawn mowers, weed eaters, grazing animals, etc. PVC conduit should be used for accessory wires such as loop detectors, key pads, card readers or any other entry device. Be sure to install conduit before pouring concrete.

Roller Guard

®

CAUTION

AUTOMATIC GATE

STAND CLEAR

1-800-543-GATE

Operator

Roller Guard

Separate PVC Conduits  for power, receiver  and control wiring.

Through the concrete pad.

MOUNTING THE LEGS ON THE SLIDE GATE OPERATOR

Roller Guard

®

CAUTION

AUTOMATIC GATE

STAND CLEAR

1-800-543-GATE

Operator

Around the concrete pad.

Roller Guard

Separate PVC Con for power, receiver  and control wiring.

STEP 1

Mount the legs on the slide gate operator using the 3/8” x 3” Carriage Bolts, 3/8” Flat Washers,

/8” Lock Washers, and 3/8” Nuts. See

Illustration A.

3/8"-16x3" Carriage Bolts

3/8" Lock Washers & Nuts

48" x 2" sq. Legs

Illustration A

Page 17

DETERMINING THE MOUNTING POSITION AND MOUNTING THE OPERATOR

STEP 2

Install chain brackets at each end of the gate on the inside (operator side) of the gate (see Overview Illustration, page.

11). Position the tops of chain brackets no more than 6” above the bottom corners of the gate frame and secure with U-bolts (see Illustration B). The chain brackets will work on gate frames 13/4" to 21/2" in diameter or square tube gates. The Ubolts provided will work on 2" diameter pipe gate frames. If

the gate will not accept this hardware, it may be necessary to purchase U-bolts sized appropriately for the gate.

Illustration C

Chain Bracket

STEP 3

Insert a quick release pin into the center slot in each of the chain brackets (see Illustration C). Tie a string to the end of each quick

Quick Release Pin

String

release pin so that the string is tight between the two chain brackets (the string will be used to align the operator). The string should be 7”-10” from the ground (see Illustration B). The chain brackets can be adjusted up or down on the gate to achieve the proper height. The goal here is to set the height of the operator so that when the housing is in place it will clear the ground by 1” to 4” (see Illustration E).

Illustration B

String

Quick Release Pin

Chain Bracket

position bracket so that string  will be approximately 7" to 10"  from ground level at the point where  the operator will be mounted

Illustration D

Gate

String

STEP 4

Find the center point between the two roller/fence posts (see Illustration D). This should coincide with the position of the

center point of the operator. Dig a hole approximately 12” x 28” wide x 28” deep. Place the operator in the hole on its legs and position the bottom idler sprockets on the top of the string and level the unit (see Illustration E). Make sure operator is level and plumb. With the unit level and in place, pour the concrete and let

set for 24 hours (checking the level periodically) before proceeding to the next step.

BEFORE POURING CONCRETE: 1] Make sure operator is centered between roller posts and aligned with string; and, 2]

Determine method of installing conduit for wiring (see page

10)!

Fence Post

Chain Sprockets

Roller

Operator

(centered between post)

Illustration E

Center point between posts

Fence Post

Roller

Level

Sprockets

Ground Level

String 7" to 10"  above ground

Housing

1" to 4" clearance

Page 18

INSTALLING THE CHAIN

Quick Release Pin

Chain

Master Link

Chain Bracket

Master Link

Chain Bracket

WARNING

•Fingers, hands, and loose clothing may be dragged into chain sprockets.

•Fingers and hands can be injured by rotating sprockets.

•Keep hands, fingers, and loose clothing away from chain and sprockets.

Illustration F

Quick Release Pin

Chain

WARNING

Sprockets

STEP 5

After the concrete has hardened, remove the string from the quick release pins. Attach the chain to one quick release pin with a master link (see Illustration

F). Run the chain through the chain sprockets (see Illustration G).

STEP 6

Pull the chain to the second chain bracket leaving approximately four inches of slack (see Illustration G). Do not pull chain tight; a tight chain will interfere with the operation of the operator. Mark the chain where it meets the second quick release pin.

Illustration G

Chain

STEP 7

Drive the pin out of the chain link using a tool such as a punch or chain break. Connect the chain to the second quick release pin using a master link (see Illustration H).

TO OPEN THE GA TE MANUALLY:

1. LIFT the quick release pins UP, then PULL them OUT of the chain brackets (see illustration).

2. Lay the chain down and manually slide the gate to the desired position.

To prevent unauthorized removal of the quick release pins, install Master® pin locks (see accessory catalog) above the quick release pins in both chain brackets.

Allow 1" of slack for every 10' of chain

Gate

Illustration H

Page 19

POWERING THE SYSTEM

RED WIRE

to positive (+)

BLACK WIRE

to negative (–)

CONNECTING THE BATTERY

Make sure the control box power switch is in the OFF position.

ON-OFF

OFF

STEP 8

Unscrew and remove the front cover of the control box and slide battery into position with its terminals to the left (see illustration). Make sure the battery fits snugly in control box.

Connect the black battery lead to the negative (–) terminal, and the red battery lead to the positive (+) terminal. DO

NOT allow battery leads to touch the control board! Touching the control board with battery leads can short circuit the system!

HINT: a dab of household petroleum jelly on each terminal will help prevent corrosion.

INSTALLATION OF THE GTO TRANSFORMER

Choose the electrical outlet into which the transformer will be plugged. Measure the distance from the electrical outlet to the control box, following the path where the low voltage wire will run

more than 1000 ft.). NOTE:

Transformer must be connected with no more than 1000 ft. of 16 gauge multi-stranded, dual conductor,

direct burial low voltage wire.

(the maximum distance can be no

Predicting the exact maximum number of operational cycles at peak load is more of an art form than an exact science. The charts below illustrate the average maximum number of cycles (the “MNC”) in a 24 hour period on a typical single gate, and is installed such that the motor draws 10 amperes to move the gate.

1) The MNC for the GTO/PRO SL-2000 is roughly comparable to most AC powered operators, and the transformer

Gate Capacity Chart for SL-1000 Series

(estimated number of cycles based on use with a transformer)

20 ft. 16 ft. 12 ft.

8 ft.

Gate Length

120 140 160 180

200 lb.

Gate Weight

110

130 150 170

300 lb.

100 120 140 160

400 lb.

110 130 150

500 lb.

Gate Capacity Chart for SL-2000 Series

(estimated number of cycles based on use with a transformer)

20 ft. 16 ft. 12 ft.

8 ft.

Gate Length

80 100 120 140

400 lb.

Gate Weight

90 110 130

600 lb.

80 100 120

800 lb.

1000 lb.

50 70 90

110

NOTE: Cycles shown are for single gate, dual gates will get approximately half as many cycles.

provided with this operator should handle most high traffic situations. If the battery does not seem to be able to provide the constant charge required for your application, the addition of the GTO/PRO 40 Amp Hour Battery Kit (see Accessoy Catalog) should provide ample power to handle any situation. For more information, call GTO’s service department at 1-800-543-GATE.

Page 20

INSTALLATION OF THE GT O TRANSFORMER CONT.

2) If the gate is binding or dragging, or if ball bearing rollers are not used, it will require more than 10 amps to move it. This will reduce the MNC.

3) The charts are based on the transformer being plugged into an outlet that provides a line voltage of 120 volts; if the outlet provides less than 120 volts (for example, some rural areas may only provide 105 volts), it can reduce the MNC by as much as 50%.

4) A fully charged standard battery has an inherent reserve of 20-50 cycles without requiring a charge. This allows peak loads at several points during the day, depending upon how much time the transformer has to provide a charge to the battery between cycles. The transformer is capable of fully recharging the battery in as little as five minutes at optimum conditions.

5) The charts on page 16 are based upon an ambient temperature of 40º F. Battery performance and speed at which it will recharge will fluctuate based upon temperature.

6) The MNC for dual gate applications will be about 50% of those for a single gate.

IMPORTANT:

• The GTO transformer is intended for indoor use. If the transformer can only be plugged into

an outside electrical outlet, a weatherproof housing or cover (available at electrical supply stores) must be used.

• Use of a surge protector is highly recommended.

• Optional Solar Panels are available from a GTO dealer; see Accessory Catalog.

• The GTO/PRO 40 Amp Hour Barrtey Kit is required for the SL-2000 in solar applications, see Accessory Catalog.

NOTE: If your are considering using the GTO solar panel to maintain the system battery charge, please see the following chart:

SOLAR ZONES AND GATE ACTIVITY

This table and map illustrates the maximum number of cycles per day to be expected in a particular area, using either one or two of GTO’s 10 watt solar panels (see Accessory Catalog). Figures are shown for winter (minimum sunlight) and do not account for use of any accessory items.

NOTE: Accessories will draw additional power from the battery.

Zone 1

Estimated Maximum Number of Cycles Per Day

Winter Ratings Watts Zone 1 Zone 2 Zone 3

SL1000 10 4 8 13 SL1000 15 6 12 20 SL1000 20 8 16 26 Dual SL1000 15 3 6 10 Dual SL1000 20 4 8 13

Requires 40 Amp Hour Battery

SL2000 10 4 8 13 SL2000 15 6 12 20 SL2000 20 8 16 26 Dual SL2000 15 3 6 10 Dual SL2000 20 4 8 13

Zone 3

Zone 2

Zone 3

Page 21

STEP 9

STATUS

BATT

PWR. SW.

Measure the distance from the electrical outlet (into which the transformer will be plugged) to the control box, following the path where the low voltage wire will run. Do not exceed 1000'.

NOTE: Pull approximately 1 foot of extra wire to accommodate terminal connections. To maintain adequate charging power, use appropriate gauge, stranded, direct burial wire (see Accessory Catalog). Do not use telephone

wire or any solid core wire because it will not provide adequate current. Never splice wires together.

INSTALLATION OF THE GT O TRANSFORMER CONT.

Illustration I

Spade Tongue

terminal

Red

STEP 10:

Strip 3/16" off the ends of the low voltage wire and attach ends to the transformer terminals;

red wire to [RED], black wire to [BLK], (see Illustration I). A dab of household petroleum

Transformer

jelly on each terminal will help prevent corrosion.

RED

BLK

We recommend crimping a spade-tongue terminal (not provided) to the end of each wire before attaching it to the transformer.

To prevent damage to transformer, make sure the exposed wire ends do to touch each other!

Black

DO NOT plug the transformer into outlet. The transformer will be plugged in during STEP 13.

NOTE: Wires coming from the ground to the

control box should be run through PVC conduit to protect them from lawn mowers, weed eaters and grazing animals (see illustrations on page 12).

STEP 11:

Feed the low voltage wires upward through the strain relief on the bottom of the control box (see Illustration J). Pull 6" to 8" of wire into the control box.

If accessories (i.e. safety loops, card readers, etc.) are to be added during this installation, do not tighten the strain relief screw against the wires until the accessories have been connected. When all accessories have been connected, fully tighten the strain relief screw against the wires.

Illustration J

  

     

PWR. SW.

–

 

  

Page 22

INSTALLATION OF THE GT O TRANSFORMER CONT.

STEP 12:

Strip 3/16" off the ends of the low voltage wire and twist tightly. These wire ends will be attached to the control board at the 18VAC terminals located on the POWER IN terminal block (see Illustration L). Wire sheathing should not come in contact with terminals, however, it should not be stripped so far that wires can come in contact with one another (see Illustration K).

Insert one transformer wire into an 18VAC terminal. Insert the other transformer wire into the remaining

18VAC terminal (see illustration L). Transformer

wires can be connected to the 18VAC terminals regardless of color.

Tighten set screws against exposed end of wires (see Illustration K). A dab of household petroleum jelly on each wire end will help prevent corrosion.

Illustration L

Illustration K

Correct

Wire

18VAC SOLAR

~~– +

RED

BLACK

RED

BLACK

Terminal  Block

RED

FIRST OPERATORPOWER IN

Wrong Wrong

GRN

Terminal  Block

CLS EDG

OPN EDG

Wire Wire

BLK

ORG

BLU

Terminal  Block

SECOND OPER

The ACCESSORY terminal block provides the connection point for safety loops, wands, push buttons, intercoms, card readers, etc. See page 27 for more information about connecting accessories.

Transformer

SURGE PROTECTOR

Power Cable

from First Operator

Low Voltage Wire

from AC Transformer

HINT: Keep a few mothballs in the control to discourage insects from entering it and damaging the control board.

STEP 13:

Plug the transformer into the electrical outlet. Check to see if the green LED on the control board is on. If it is not, see the Troubleshooting Guide on page 30.

NOTE: Use of a surge protector is strongly recommended.

Page 23

CONTROL BOARD SETTINGS

DIP SWITCHES

The four DIP switches on the control board match the operator with the type of gate on which it is mounted. For example, gates may open right to left or left to right. Prior to packaging, the GTO/PRO Sl-1000 and SL2000 series control board was configured for a single slide gate that opens right to left. If your gate type matches this configuration, you DO NOT need to adjust the DIP switches. Proceed to the Potentiometers section on the next page.

NOTE: To change the DIP switch settings, you must turn the control box power switch OFF; move the switch; then turn the power back ON. Use a small screwdriver to move the switches.

PULL/PUSH: Set to PULL for slide gates that open RIGHT to LEFT [factory setting]; PUSH for slide gates that open LEFT to

DIP switches

RIGHT. NOTE: The direction a gate opens is determined by standing inside the property and facing toward the gate.

SNGL/DUAL: Set to SNGL for a single gate leaf [factory setting];

PULL/PUSH

SNGL/DUAL

DUAL for dual gate leaves. SEQ1: Controls the opening order of dual gate leaves. See Dual Gate Operator Installation on page 33 for more information. (the factory

setting is OFF).

SEQ2: Controls the opening order of dual gate leaves. See Dual Gate Operator Installation on page 33 for more information. (the factory setting is OFF).

STATUS

BATT

–

PWR. SW.

SEQ1 SEQ2

1234

AUTOCLOSE

OFF

INERTIA

MIN

OBSTRUCT SENS.

OBSTRUCT

SENS.

MIN MAX

LEARN

120

MAX

ORG

BLK

18VAC SOLAR

RED

~ ~ – +

FIRST OPERATOR

POWER IN

BLU

CLS EDG

GRN

OPN EDG

CLS EDG

GRN

BLU

ORG

BLK

RED

SECOND OPERATOR

ALARM

PULL/PUSH

L/DUAL

SEQ

BLU

ORG

GRN

ACCESSORY

WHT

MIN

LEARN

RCVR

MAX

Page 24

POTENTIOMETERS

The three (3) potentiometers on the control board operate like a volume control on a radio. They control the auto close timer, inertia, and obstruction sensitivity of the operator. Use a small slotted screwdriver to turn the arrow in the center of the potentiometer. Clockwise rotation increases the setting (MAX). Counterclockwise rotation decreases the setting (MIN).

PULL/PUSH

SNGL/DUAL

SEQ1 SEQ2

R B G

RCVR

AUTOCLOSE

OFF 120

INERTIA

MIN

OBSTRUCT SENS.

MIN MAX

1234

LEARN

AUTO CLOSE (auto close timer): Determines how long the gate will remain

open before it automatically closes. The limits are OFF to 120 seconds. The factory setting is OFF.

INERTIA: Fine tunes obstruction sensitivity in the opening and closing modes. INERTIA allows the operator to attempt to push an obstruction clear

MAX

of the gate path. When INERTIA is set to MIN the operator will obstruct quickly (i.e, will attempt to push an obstruction briefly); when set to MAX the operator will obstruct slowly (i.e., will push against an obstruct for a longer period). The factory setting is MIN.

OBSTRUCT SENS. (obstruction sensitivity): Determines the amount of force exerted by the gate on an obstruction before the operator stops and reverses.

The gate will exert minimum force before obstructing when set to MIN. When set to MAX, the operator will exert maximum gate force before obstructing (i.e., the operator will require greater resistance before stopping and reversing.). The factory setting is MIN.

READ WARNING BELOW!

NOTE: Heavy gates and gates with high wind resistance may require the OBSTRUCT SENS. potentiometer to be set closer to MAX to prevent the operator from obstructing. Keep in mind, however, that while you must determine the best setting for smooth gate operation, you must ALSO determine the lowest possible setting for safe gate operation.

ALWAYS KEEP SAFETY AT THE TOP OF YOUR LIST WHEN ADJUSTING OR SERVICING

YOUR AUTOMATIC GATE OPERATOR!

All three potentiometers were set to minimum at the factory. The OBSTRUCT SENS. potentiometer MUST be adjusted above the factory setting for your GTO/PRO SL-2000 series operator to function properly. If the potentiometer is left at MIN, your gate operator may "obstruct" (i.e., stop and reverse) as soon as it is activated.

BE SURE TO PROPERLY RETEST THE GATE OPERATOR AFTER MAKING ANY ADJUSTMENTS; FAILURE TO DO SO MAY RESULT IN SERIOUS INJURY OR DEATH.

WARNING!

Page 25

, In

, Inc.

CONNECTING THE RECEIVER TO THE CONTROL BOARD

BATT

PWR. SW.

Insert the end of the receiver cable (stripped and soldered at the factory) into the hole underneath the audio entrapment alarm (bottom right of control box). Wire the receiver to the control board at the terminal block marked RCVR. Connect the red wire to R, green wire to G, black wire to B. Tighten the set screws on the soldered end of the wires.

Replace the control box cover and proceed to the next step.

SEQ1 SEQ2

–

INERTIA

OBSTRUCT SENS.

AUTO CLOSE

STATUS

–

Audio Entrapment Alarm

Receiver Cable

GRN

ORG

BLU

WHT

R B G

ALARM ACCESSORY RCVR

RED Wire

BLACK Wire

GREEN Wire

LEARN

SETTING THE PERSONAL TRANSMITTER CODE

All GTO transmitters are set to a standard code at the factory and are ready to activate the automatic gate operator. For safety and security, however, we strongly recommend that the factory setting be replaced with a personal code. Follow the directions below:

1. REMOVE THE TRANSMITTER COVER

Grasp the sides of the access cover and slide it away from the transmitter button (see illustration). When the access cover is removed, the battery and the DIP switches will be exposed. To set a new code, use a small screwdriver to move the switches.

Page 26

2. SET THE TRANSMITTER DIP SWITCHES

There are nine (9) transmitter DIP switches; each of which can be placed in three different positions (+, 0, –). DO NOT set all the switches in the same position, such as all +, all 0, or all –. Once the DIP switches have been set to a personal code, replace and close the access cover.

WARNING: No other adjustments should be made inside the transmitter.

3. “TEACH” THE NEW CODE TO CONTROL BOARD MEMORY

A. Turn control box power switch OFF.

B. Unscrew and remove the control box cover. C. Press and hold the LEARN button on the control board, and

turn the power switch ON. Release LEARN button. Wait 15 seconds for the receiver to charge.

D. Press and hold transmitter button until the red STATUS LED

comes ON.

E. Release transmitter button. The new code is stored in control

board memory.

MOUNTING THE RECEIVER

Use the transmitter to check the range of the receiver before permanently mounting it.

STATUS LED

STATUS

PULL/PUSH

SNGL/DUAL

SEQ1 SEQ2

R B G

1234

RCVR

AUTOCLOSE

OFF 120

INERTIA

MIN

MAX

OBSTRUCT SENS.

MIN MAX

LEARN

Consider the following when mounting the receiver:

• Receiver cable length is 20 feet (receivers with a longer cable are available as special order items; Call the GTO Sales Department). NEVER splice receiver cable!

• Run the cable through PVC conduit to protect it from damage.

• DO NOT run cable through metal conduit because the receiver signal range will be decreased.



• DO NOT run cable in a conduit containing AC wiring.

• DO NOT mount receiver on a metal fence or post; doing so will decrease signal range.

• DO NOT overtighten the mounting screws; the receiver housing could be warped and the weather seal damaged.

• The receiver range can vary from 50 to 100 feet depending upon weather, topography, and external interference.

FCC Regulation

This device complies with FCC rules Part 15. Operation is subject to the following conditions:

1. This device may not cause harmful interference.

2. This device must accept an interference that may cause undesired operation.

Transmitter distance may vary due to circumstances beyond our control. NOTE: The manufacturer is not

responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

Page 27

Limit Nut

Closed position stop – if gate opens right to left. Open position stop – if gate opens left to right.

Limit Nut A

Open position stop –

if gate opens right to left. Closed position stop – if gate opens left to right.

ADJUSTING THE LIMIT SWITCHES

After the operator is installed, adjust the open and closed position limit switches as needed. The limit switches determine how far the gate travels to open and to close.

Adjust the limit switches using the limit nuts. Lift limit switch plate to adjust limit nuts (see Illustration M).

The open and closed position switches will be reversed depending on whether the gate opens from left to right or from right to left (see Illustration N).

WARNING! In order to adjust switches, the control box must be ON. USE CAUTION when adjusting limit switches to prevent fingers, hair, clothing, etc., from getting caught under the limit switch plate and possibly causing bodily injury.

If your gate opens from Right to Left:

1. Gate Opening: For gate to open further, turn Limit Nut A counterclockwise. For gate to open less, turn Limit Nut A clockwise.

2. Gate Closing: For gate to close further, turn Limit Nut B counterclockwise. For gate to close less, turn Limit Nut B clockwise.

Illustration M

Limit Nut A

Counter Clockwise

Limit Switch Plate

Limit Nut B

Motor

Clockwise

However, if your gate opens from Left to Right:

1. Gate Opening: For gate to open further, turn Limit Nut B counterclockwise. For gate to open less, turn Limit Nut B clockwise.

2. Gate Closing: For gate to close further, turn Limit Nut A counterclockwise. For gate to close less, turn Limit Nut A clockwise.

Once the limit switches are adjusted, make sure the limit switch plate rests in the grooves on both limit nuts.

Illustration N

Page 28

CONNECTING SAFETY DEVICES

The GTO/PRO SL-1000 and SL-2000 series operators are equipped with built-in obstruction sensitivity. These operators are designed to stop and reverse the gate for 2 seconds when it comes in contact with an obstruction. However, obstruction sensitivity, even when properly adjusted, may not be sensitive enough to prevent bodily injury. For this reason, safety edges or photoelectric sensors MUST be installed on the gate. Safety edges (or photoelectric sensors) must be mounted in compliance with Underwriters Laboratories’ safety standard for gate operators, UL 325. Review page 4 for information about mounting requirements for safety edges and photoelectric sensors.

Refer to the sensor manufacturer’s instructions for information about installing these devices on a vehicular gate.

Make sure the control box power switch is OFF before connecting safety device wiring to the terminal blocks.

Insert the safety device wires into the CLS EDG terminal (located on the FIRST OPERATOR terminal block) for the gate closing mode. Ground the safety device at the GRN terminal. Connect the safety device wires for the gate opening mode to the OPN EDG terminal in the same manner.

MAKE SURE TO GROUND THE SAFETY DEVICES AT THE GRN TERMINAL! THE CONTROL BOARD COULD BE DAMAGED IF THE SAFETY DEVICES ARE NOT GROUNDED!

18VAC SOLAR

~~– +

Power Cable

from First Operator

Wire from Close Safety Edge

or Photoelectric Sensor

RED

Ground Wire

BLK

ORG

BLU

GRN

CLS EDG

OPN EDG

RED

BLK

ORG

BLU

GRN

CLS EDG

OPN EDG

SECOND OPERATORFIRST OPERATORPOWER IN ALARM ACCESSORY RCVR

Ground Wire

Wire from Open Safety Edge or Photoelectric Sensor

GRN

ORG

SEQ1 SEQ2

BLU

WHT

LEARN

R B G

Page 29

COMPATIBLE SAFETY DEVICES

Although GTO strongly recommends the use of safety devices, we do not endorse any specific brand names. Below is a list of some products compatable with GTO operators systems, some of which require their own power supply. Check with the individual manufacturer for specific power needs.

Only use products that are certified and listed to be in compliance with national and regional safety codes.

SAFETY EDGES

Miller Edge, Inc.

MC-22 ME-110 through 113 ME-120 ME-123 MG-020 MT-21 and 22 MU-22

Tapeswitch Corporation

101-B and BMT 102-A, B, BP, BPH 107-RS and LS 121-BP 131-A and AMT 141-BMH 191-S IL

PHOTOELECTRIC BEAMS

Texas Optoelectronics, Inc.

Industrial Photobeam

EMX Industries, Inc.

IRB-4X

NOTE: This is not an exhaustive list of compatible safety devices.

Page 30

CONNECTING ACCESSORIES

Make sure the control box power switch is OFF before connecting accessories.

The ACCESSORY terminal block is the connection point for accessories such as push buttons, safety loops, intercoms, etc. The ACCESSORY terminal marked GRN (green) is the common ground for all accessories.

GRN is paired with the terminals shown below when connecting accessories to the control board. IMPORTANT: Make sure to twist exposed wires tightly and insert them into the terminals without

loose strands. Tighten set screws against exposed end of wires. A dab of household petroleum jelly in each

terminal will help prevent corrosion.

WHT (WHITE) USED WITH GRN ( GREEN):

Functions as a normally open contact. This is the most frequently used pairing for a doorbell button, keypad, or keyswitch.

First contact will start the gate. Second contact will stop the gate. Third contact will reverse the gate.

NOTE: Never use a lighted doorbell button! It will discharge the battery and the gate operator will fail to operate.

BLU (BLUE) USED WITH GRN (GREEN):

Functions as a normally open contact. This pairing is typically used for a free exit or free entry devices.

First contact will open the gate.

Low Voltage Wire

from Doorbell Button,

Keypad, or Key Switch

SEQ1 SEQ2

BLK

ORG

WHT

GRN

ALARM ACCESSORY RCVR

GRN

ALARM ACCESSORY RCVR

ORG

SEQ1 SEQ2

BLU

WHT

R B G

LEARN

NOTE: If the gate is in the open position and begins to close, the activation of the accessory device will reopen the gate. In communities where the use of a emergency entry device is mandatory, it should be connected to these terminals.

ORG (ORANGE) USED WITH GRN (GREEN):

Functions as a normally open contact. This pairing is frequently used for safety loops.

This connection will not open your gate. The safety loop will activate only while the gate is in use. When using this combination, the gate will remain open or reopen if it is closing.

Low Voltage Wire

from Free Entry or

Free Exit Devices

Low Voltage Wire

from Safety Loops

SEQ1 SEQ2

BLU

ORG

WHT

GRN

ALARM ACCESSORY RCVR

R B G

LEARN

Page 31

ATTACHING THE HOUSING

Safety Instructions

IMPORTANT

Mount the operator housing after all installation procedures are complete. Slide operator housing over legs, align holes, and use screws provided to attach housing to operator.

IMPORTANT: Hang the two (2) GTO Warning Signs (provided) on both sides of the gate before operating. Make sure all warning signs and labels are in place. Make sure that the packet containing end user safety instructions and warranty procedures remains attached to the operator housing (as shown in the illustration).

Page 32

MAINTENANCE

The GTO Slide Gate Operator is designed for minimum maintenance. However, for optimum performance and safety, the following maintenance procedures should be taken:

GATE

Having a well maintained gate will ensure that the operator runs smoothly and safely. Make sure gate is hung level and plumb. Check and adjust periodically. Lubricate rollers periodically with grease appropriate for the

coldest weather in your area.

SAFETY EDGES

Periodically test the safety edges to make sure they are functioning correctly. If they are not, discard and replace immediately.

CONTROL DEVICES

From time to time, check to ensure that all of the control devices connected to the operator are functioning. This is especially important for safety devices.

OPERATOR

Occasionally inspect the chain to ensure that it is well lubricated, and oil the chain as necessary. Use CHAIN AND CABLE LUBE for best results. Check the gear sprockets and grease them as needed. Check the rollers and spray oil on them as needed.

Review the safety precautions & operator warranty procedures contained in packet (attached to the operator housing) with the customer. Leave packet attached to the housing for future reference.

Page 33

TROUBLE SHOOTING GUIDE

Maintenance:

• On all gates weighing 250 lb. or more, routinely grease the ball bearing rollers at least 4 times a year; grease

more frequently if the gates are near a coastal area.

• Keep a few mothballs in the control box to discourage insects from entering it and damaging the control board.

• Have your gate operator tested monthly and serviced regularly by an experienced technician. The gate MUST stop and reverse on contact with an obstruction or when an object activates the non-contact sensors. If these functions are observed to operate improperly, discontinue use and have operator serviced immediately.

The operator has a 12 Vdc motor with mechanical limit switches.

• To test the motor, put a voltmeter on DC and place the meter leads on the wire connections inside the plastic

cover above the switches. The reading should be at least 11.5 V when the system is active. If it is not, see The Control Board section

• To test the switches, put the meter on “ohms.” Place the leads on each of the wires on the switch. You should have an open circuit. Click the switch and you should have .2 ohms. Do this for both switches.

• To test the cable, put the meter on ohms. At one end of the cable place the lead on the green wire, and on the other end of the cable place the lead on the green wire and the other wires. This should show a maximum of 1.0 ohms on the green wire and nothing on the other wires. Test each wire as you have above. If all have the proper readings, then this is not the problem.

• Note: Inspect the cable for any signs of any punctures because wires inside the PVC jacket can be shorted and the cable will still show proper ohms.

The control board: This is a micro processor board. The power that runs the gate is from the battery and recharged,

through the board only, by a 18 volt 40 VA. (2.9 A) transformer. There is one (1) green and one (1) red LED (light emitting diode) on the control board. They are for a quick

reference only. All readings must be measured by a voltmeter! The red light serves two purposes. The first is to aid in storing the personal transmitter code. See “Setting

the Personal Transmitter Code”. The second is to show the condition of the battery. If it is flashing, see the following section on “ Testing the

battery.” The normal state of this light is on, but dim. If the red LED is flashing it means that the system may have reached low voltage lockout; the unit does not

have enough voltage to operate the system. One of the following problems may exist:

• Broken or spliced wires from the transformer or solar panel to the control board.

• A transformer or solar panel that has no output voltage.

• Incorrect number of solar panels, or solar panels not properly hooked up. The green light serves as a quick visual indication that the control board is receiving power from the

transformer.

The transformer: Two things can cause failure: the first is shorting the leads during the installation, or letting the

strands touch at the terminal on the control board. The second is a static charge (generally associated with a lightning storm or power outage); use of a surge protector will help.

Testing the battery: This is a 12 volt 7 Ah battery. The proper way to test this is to perform a load test. Place the

voltmeter on D.C.; put the red probe on the (+) positive terminal and place the black probe on (-) negative

Page 34

terminal. Then activate the unit and watch the voltmeter. The drop should not be more than 1 volt. Note: A loose battery terminal will cause the same symptoms that a bad battery will cause. Terminals should

be secure and corrosion free.

Remote control range: This will vary at each installation. (see FCC disclaimer on page 23), but generally varies

from 50 ft. to 100 ft.

• Make sure that the receiver is located above metal fences.

• Moving the receiver even a few inches can change the range of operation.

• Move the receiver as far from the motor as possible to avoid the chance of electrical interference.

• Check or change the battery in the transmitter.

SYSTEM TEST SPECIFICATIONS

Transformer: 120 Vac / 60 Hz input

18 Vac / 40 VA output 10 W solar panel: 18-22 Vdc / 600 mA per hour Battery: 12 Vdc / 7 Ah Wire: 16 gauge, multi stranded, direct burial Motor: 12 Vdc 90 rpm with case hardened gears. The motor current range

is 2.5 to 10 A if the gate is in good working order. Receiver: 5 Vdc / digital communication. ONLY GTO receivers can be

connected to these terminals.

Control board: Microprocessor driven. Powered by 12 Vdc.

The GTO, Inc. Technical Service Department is open

Monday – Thursday 7:30 A.M. – 5:30 P.M.

and Friday 8:00 A.M. - 12:00 P.M. (Eastern Time)

TELEPHONE (800) 543-GATE OR (850) 575-0176

FAX (850) 575-8950 • E-mail: techsupport@gtoinc.com • www.gtoinc.com

Page 35

WARRANTY AND REPAIR SERVICE

If the GTO gate operator system is not operating properly and you have not been able to solve the problem, please follow the steps below:

1. Check the Trouble Shooting Guide (page 29).

2. Call your installer.

3. If you still cannot solve the problem, call the GTO Service Department at (850) 575-0176.

4. If repair or replacement is necessary, you will be assigned a Return Goods Authorization Number (RGA).

Write the RGA # in LARGE BOLD PRINT on the outside of the package.

5. Carefully pack the component(s) authorized for return and ship freight prepaid to GTO, Inc., 3121 Hartsfield Road, Tallahassee, Florida, USA 32303.

NOTE: GTO products returned without a Return Goods Authorization Number (RGA) or returned freight

collect WILL NOT be accepted at the factory. A copy of the owner’s receipt with date of sale and

installation must accompany warranty related request for service.

If the repair service or replacement is covered by the warranty, GTO, Inc. will pay shipping costs (equal to United Parcel Service ground rate) for return to owner of items repaired under warranty.

AUTOMATIC GATE OPERATORS

Limited Two Year W arranty

GTO/PRO DC powered gate operators are warranted by the manufacturer against defects in materials and manufacturer workmanship for a period of two (2) years from date of purchase, provided recommended installation procedures have been followed.

In the case of product failure due to defective material or manufacturer workmanship within the two (2) year warranty period, the operator will be repaired or replaced (at the manufacturer's option) at no charge to the customer, if returned freight prepaid to GTO, Inc., 3121 Hartsfield Road, Tallahassee, Florida 32303. IMPORTANT: Call

(850)575-0176 or fax (850) 575-8950 for a Return Goods Authorization (RGA) number before returning to factory. Products received at the factory without an RGA number will not be accepted. Replacement or repaired

parts are covered by this warranty for the remainder of the two (2) year warranty period or six (6) months, whichever is greater. GTO will pay the shipping costs (equal to United Parcel Service ground rate) for return to the owner of items repaired under warranty.

The manufacturer will not be responsible for any charges or damages incurred in the removal of the defective parts for repair, or for the reinstallation of those parts after repair. This warranty shall be considered void if damage to the product(s) was due to improper installation or use, tampering, connection to an improper power source, or if damage was caused by lightning, wind, fire, flood, insects or other natural agent. This warranty gives you specific legal rights, and you may also have other rights which may vary from state to state. This warranty is in lieu of all other warranties, expressed or implied. NOTE: Verification of the warranty period requires copies of receipts

or other proof of purchase. Please retain these records.

After the two (2) years warranty period, GTO or one of its authorized service centers will make any necessary repairs for a nominal fee. Call GTO at (850) 575-0176 for more information.

Page 36

INSTRUCTIONS FOR THE INSTALLATION OF

A DUAL GATE SYSTEM

AUTOMATIC GATE OPERATORS

USE THE GT O/PRO SL-2200 WITH THE

GTO/PRO 2000 FOR DUAL GATES

Page 37

DUAL GATE SYSTEM INSTALLATION

Install the second gate operator in the same manner as the Single gate operator starting on page 12 of this manual. The second gate preparation and wiring of the second (auxiliary) operator follow on the next two pages. Once the second gate operator is installed, Set the DIP switches for DUAL gates and the order in which the gates open (“sequencing”). Setting the Control Board for Dual Gate Installations begins on

page 37.

SECOND GATE (AUXILIARY) OPERATOR PARTS & HARDWARE

Second Gate Operator

(2) 2” square x 48” long legs

The SL-2200 comes with a battery and control box the SL-1200 does not.

(2) Chain Brackets

(4) 3/8” -16 x 3” Carriage Bolts

(4) 3/8” Lock Washers

Battery

(4)

Battery Cable

”-16 x 2” dia.

/ U-Bolts

Operator Housing

32’ Drive Chain

60’ Power Cable w/ Strain Relief

(4) 1/4”-20 x 1/2” Screws

(4) 3/8” Nuts

(2) Chain Master Links

(8) 3/8” Serrated Nuts

(2) Quick Release Pins

Page 38

PREPARING THE GATES

Install PVC conduit (not included) needed for power cables and low voltage wiring – see illustration below. The PRO SL-1200 and Sl-2200 power cable and safety edge (required) wiring should be run through PVC conduit underneath the driveway. If you cut the driveway be sure to reseal it after all wiring is installed.

PVC Conduit for second operator power cable.

Safety Edge

(REQUIRED)

Safety Edge

(REQUIRED)

Safety Edge

(REQUIRED)

WARNING

Moving Gate Can Cause

Injury Or Death

1.KEEP CLEAR! Gate may move at any time.

2.Do not allow children to operate gate or play in gate area.

3.This gate is for vehicles only. Pedestrians must use a separate entrance.

Chain Bracket

Chain

Roller Guard

(REQUIRED)

First Gate Operator

(Control Unit)

Roller Guard

(REQUIRED)

Safety Edge

(REQUIRED)

Roller Guard

(REQUIRED)

Chain Bracket

®

CAUTION

AUTOMATIC GATE

STAND CLEAR

1-800-543-GATE

SL-1000

or SL-2000

First Operator

PVC Conduit for power cable.

Safety Edge

(REQUIRED)

Safety Edge

(REQUIRED)

Receiver (cable in separate conduit)

Roller Guard

(REQUIRED)

Run up to 1000' of low voltage wire to control box from transformer (wire not included).

120 Volt Indoor Transformer

(Surge Protector

not supplied)

Chain Bracket

®

CAUTION

AUTOMATIC GATE

STAND CLEAR

1-800-543-GATE

SL-1200

or SL-2200

Second Operator

Roller Guard

(REQUIRED)

Second Gate Operator

(Auxiliary Unit)

Roller Guard

(REQUIRED)

WARNING

Moving Gate Can Cause

Injury Or Death

1.KEEP CLEAR! Gate may move at any time.

2.Do not allow children to operate gate or play in gate area.

3.This gate is for vehicles only. Pedestrians must use a separate entrance.

PVC Conduit for second operator power cable.

Chain Bracket

Chain

Page 39

WIRING THE SECOND OPERATOR

RED

BLACK

ORANGEBLBL

GREEN

RED

BLACK

ORANGEBLBL

GREEN

First Operator Power Cable

Second Operator Power Cable

AUTO CLOSE

INERTIA

STATUSSTATUS

BATT

–

OBSTR. SENS.

POW

ER IN

–

PWR. SW.

Lock Nut

Hub

Sealing Nut

Hub

Lock Nut

Strain Relief

Wire From Second Operator Battery

When the units are set in place and you have completed wiring the first unit follow the instructions below .

Step 1: With the PRO SL-1000 or SL-2000 control box open, use a screw driver to punch out the round knockout hole located on the bottom next to the First Operator power cable. Install the strain relief for the Second Operator power cable. Leave about 6” of the power cable and tighten the strain relief nut to secure the wires.

THIS STEP IS FOR SL-2000/ 2200 INSTALLATION ONLY

18VAC SOLAR

Step 1a: Run the battery jumper wire through the PVC from the battery in the Second Operator to the battery in the First Operator. Use the side strain reliefs on the control boxes to run battery jumper wire into control boxes. Using spade connectors, connect positive to positive and negative to negative.

~~– +

Low Voltage Wire

from AC Transformer

RED

BLK

ORG

BLACK

ORANGE

BLACK

ORANGE

BLU

BLUE

GRN

GREEN

CLS EDG

OPN EDG

RED

BLK

ORG

BLU

GRN

CLS EDG

OPN EDG

SECOND OPERATORFIRST OPERATORPOWER IN ALARM ACCESSORY RCVR

RED

BLACK

ORANGE

BLACK

ORANGE

BLUE

GREEN

RED

GRN

ORG

SEQ1 SEQ2

BLU

WHT

R B G

LEARN

Step 2: Run the second power cable through PVC conduit to the Second Operator. Connect the wires to the motor and limit switches as shown in illustration

Step 3: Adjust the DIP switches on the First Operator control board for the appropriate dual gate settings, following the directions on next page.

Power Cable

from First Operator

Limit Nut A

Open position stop –

if gate opens right to left. Closed position stop – if gate opens left to right.

Power Cable

from Second Operator

Closed position stop – if gate opens right to left.

Open position stop – if gate opens left to right.

Limit Switches

Motor

Limit Nut B

Second Operator

Power Cable

BLUE (N/O contact) GREEN (common) ORANGE (N/O contact) BLACK to Motor RED

RED to Motor BLACK

Page 40

SETTING THE CONTROL BOARD FOR DUAL GATE INSTALLATIONS

DIP SWITCHES

The Control Board DIP switches must be set to accommodate your particular type of installation. Since the SNGL / DUAL, SEQ1, and SEQ2 DIP switches are used by dual gate operator systems, they will be discussed in the following steps.

STEP 4:

Make sure the control box power switch is OFF.

OBSTRUCT

STEP 5:

Unscrew and remove the control box cover. Use a small screwdriver to move the SNGL / DUAL DIP switch to DUAL (see illustration).

The order of gate operation ("sequencing") must now be determined for your dual gate operators to function properly.

Refer to the illustrations on the next page. NOTE: The terms "FIRST OPERATOR" and "SECOND

OPERATOR" refer to a unit wired to the terminal block of the same name.

PULL/PUSH

SNGL/DUAL

SEQ1 SEQ2

SENS.

MIN MAX

1234

LEARN

STEP 6:

BOTH OPERATORS OPEN SIMULTANEOUSLY BOTH OPERATORS CLOSE SIMULTANEOUSLY

SEQ1 = ON SEQ2 = OFF If SEQ1 is set to ON, and SEQ2 is set to OFF, the FIRST

OPERATOR and SECOND OPERATOR open simultaneously, and the FIRST OPERATOR and SECOND OPERATOR close simultaneously (see illustration).

PULL/PUSH

SNGL/DUAL

SEQ1 SEQ2

OBSTRUCT SENS.

MIN MAX

1234

LEARN

Page 41

FIRST OPERATOR OPENS FIRST, SECOND OPERATOR CLOSES FIRST

OBSTRUCT SENS.

SEQ1 = OFF SEQ2 = ON If SEQ1 is set to OFF, and SEQ2 is set to ON, the

FIRST OPERATOR will open first, and the SECOND OPERATOR will close first (see illustration).

FIRST OPERATOR OPENS FIRST, FIRST OPERATOR CLOSES FIRST

SEQ1 = ON SEQ2 = ON If SEQ1 is set to ON, and SEQ2 is set to ON, The

FIRST OPERATOR opens and closes first.

BOTH OPERATORS OPEN SIMULTANEOUSLY SECOND OPERATOR CLOSES FIRST

PULL/PUSH

SNGL/DUAL

SEQ1 SEQ2

PULL/PUSH

SNGL/DUAL

SEQ1 SEQ2

MIN MAX

1234

LEARN

OBSTRUCT SENS.

MIN MAX

1234

LEARN

OBSTRUCT SENS.

SEQ1 = OFF SEQ2 = OFF

PULL/PUSH

SNGL/DUAL

If both SEQ1 and SEQ2 are set to OFF, the FIRST OPERATOR and SECOND OPERATOR will open simultaneously. The SECOND OPERATOR will close first.

STEP 7:

Replace the control box cover. Turn the control box power switch to ON. Set the closed gate positions for the first and second operators by adjusting the limit switch (review page 24).

SEQ1 SEQ2

MIN MAX

1234

LEARN

Page 42

ACCESSORIES AVAILABLE THROUGH YOUR DEALER

GTO Digital Keypad (F300)

The weatherproof digital keypad can be easily installed as a wired or wireless keypad for all GTO

789

HEDDOLF

UNIVERSAL

RECEIVER

MODEL 294

Garage Door Receiver (RB709)

Allows the use of the same GTO remote transmitter (see Dual and Triple Transmitters) to control the gate operator and garage door

opener. Compatible with most garage door openers.

swing and slide gate operators, and as a wired keypad for the Bulldog Pedestrian Gate Lock. It can be programmed to recognize fifteen different personal identification number (PIN) codes. Each code is face programmable with additional security features built in. Requires 3 AA batteries (not included). Can also accommodate most garage doors and other gate openers. If used as a wired keypad, 16 gauge standard, low voltage direct burial wire will be required (see RB509).

SECURITY GATE LOCK

GTO Entry Transmitter (RB741)

The GTO Entry Transmitter, with adjustable code settings, is standard equipment with all GTO gate operator systems. Battery included.

GTO Key Chain Mini Transmitter (RB744)

This miniature version of the GTO entry transmitter has the same adjustable code settings. Battery included.

GTO Dual Transmitter (RB742) GTO Triple Transmitter (RB743)

The two and three button transmitters are used for the remote control of two or three gate operators and garage door openers (See Garage Door Receiver). Battery included.

Push Button (Doorbell) Control

(RB101)

Unlighted doorbell button for remote

entry or exit control. Connects directly to the control board using 16 gauge stranded, low voltage, direct burial wire

(not included, see RB 509).

GTO Bulldog Pedestrian Gate Lock (FM500)

Similar to the Automatic Gate Lock but designed for horizontal use only on "walk-through" gates without automatic operators. The Bulldog is an affordable solution to protecting swimming

, I n c

pool areas, playgrounds, tennis courts, boat docks, etc., from unwanted access. Includes control box and keyed manual release. Can be used with the GTO Digital Keypad (F300).

GTO NEMA Box (FM317)

GTO's NEMA 4X rated weatherproof box is large enough (14" W x 6" D x 16" H) to accommodate all add-on items necessary for custom gate operator installations. It is made of fire retardant ABS plastic and comes with a heavy duty 14 gauge steel backing plate for mounting accessories. The unique, lockable cover (use the Master® Pin lock RB975 for added security) can be completely removed for easier access during installation and service.

The NEMA box is standard on all GTO/PRO AC powered operators.

Page 43

ACCESS-ORIES

Master® Pin Lock (RB975)

for GTO/PRO SL-2000/2200 The pin lock can be inserted in the

chain brackets of the GTO/PRO SL2000/2200 to prevent unauthorized removal of the quick release pins.

GTO Low Voltage Wire (RB509)

The 16 gauge dual conductor, multistranded, direct burial low voltage wire is required to connect the control board to the solar panel or the AC transformer. This wire is also required for installation of some accessories such as keypads, locks, or push buttons (available in 1000' rolls and specially cut lengths).

Splice Kit - Above Ground (RB707)

For providing secure and moisture resistant above ground splices for solar panels, key pads, push buttons and other accessories using GTO low voltage wire.

Splice Kit - Direct Burial (RB708)

When direct burial wire running below ground needs to be spliced the RB708 splice kit must be used.

Operator Solar Panel (FM123 ) - Improved, Amorphous Silicon (Two Year Warrant*)

This 10 watt solar panel is a battery charger for use with GTO/PRO Low Voltage Automatic Gate Operator systems. Particularly suited for remote installations, the solar panel comes with tubular steel support, mounting clips, wire connectors, and 8 ft. of low voltage wire (for longer lengths, see RB509). All GTO low voltage operators are pre-wired for solar panels. Installation in some regions of the world will require multiple panels for adequate charging power. Recommended for GTO/PRO 2000/2200, GTO/PRO SL-1000/SL-1200.

Operator Solar Panel (FM122 ) - Improved Amorphous Silicon (Two Year Warrant*)

The 5 watt solar panel is a battery charger for use with GTO/PRO Low Voltage Automatic Gate Operator systems. Particularly suited for remote installations, the solar panel comes with tubular steel support, mounting clips, wire connectors, and 8 ft. of low voltage wire (see Low Voltage Wire for longer wire). All GTO low volatge operators are pre-wired for solar panels. Installation in some regions of the world will require multiple panels for adequate charging power. Recommended for GTO/PRO 1000, GTO/PRO 1200 and the GTO Bulldog Gate Lock.

Dual gate installations require minimum of two (2) 5 watt solar panels for adequate charging power.

Page 44

ACCESS-ORIES

Standard Replacement Transformer (RB570) –Standard 18 volt AC transformer for GTO/PRO SL-2000

series gate operators

Bulldog Replacement Charger (RB421) – Standard 12 volt DC charger for maintaining battery included

with the Bulldog Pedestrian Gate Lock.

Replacement Batteries

RB500 – The standard 12 volt, 7.0 ampere-hour, maintenance-free battery for all GTO/PRO gate operators. This is the only battery approved for use with GTO gate operators. Battery life 3 to 5 years.

RB422 –The 12 volt, 1.2 ampere-hour version for use with the Bulldog Pedestrian Gate Lock.

GTO/PRO 40 Amp Hour Battery Kit

FB295 – This large 12 volt, 40 ampere-hour, maintenance-free battery is for the GTO/PRO SL-2000&2200 gate operators. It will supply additional power for increasing the number of

open and close cycles of the GTO/PRO SL-2000&2200 operators. The kit comes with the battery, battery pan and wiring harness for easy installation inside the existing operator housing. This is the only battery approved for use with GTO gate operators. Battery life 3 to 5 years.

Replacement Receivers

The AQ201: Receiver with a 10 ft. cable (included). The AWQ325: Receiver with a 25 ft. cable. The AWQ350: Receiver with a 50 ft. cable. The AWQ400: Receiver with a 100 ft. cable.

Standard Replacement Power Cables for Gate Operators

The PRO 60C (AC202): 60 ft. power cable included with GTO SL-2200 dual (second) slide gate operator.

* GTO, Inc. gate operator accessories are warranted by the manufacturer against defects in materials and

workmanship for a period of one year, unless otherwise stated, from the date of purchase provided recommended installation procedures have been followed. Warranty is considered void if damage was due to improper installation or use, connection to an improper power source, or was caused by lightning, wind, fire, flood, insects, or other natural agent.

Page 45

INSTALLATION CHECK LIST

The installation of this operator conforms to CLASS __________.

The installer verifies that (each item must be checked):

___ Required safety edges were installed.

___ Roller guards were installed over gate rollers.

___ Fence was screened so that no one can reach through the gate to operate controls.

___ Customer was informed that this gate is for vehicular use ONLY. Pedestrians MAY NOT use this gate.

___ A separate gate or entrance was installed for pedestrian use.

___ All warning signs and labels were installed as specified in the IMPORTANT SAFETY INSTRUCTIONS.

___ Safety instructions were reviewed with the customer.

___ The IMPORTANT SAFETY INSTRUCTIONS manual was given to the customer.

___ Customer was instructed about proper use of the foot pedal release.

___ Customer was instructed about proper use of transmitter and (or) other entry controls.

___ Customer was asked to fill out customer support card and mail it to GTO, Inc.

___ Customer was asked to retain all receipts (receipts provide proof of warranty).

___ Customer was asked to retain IMPORTANT SAFETY INSTRUCTIONS, etc. for future reference.

___ The completed installation was photographed from both the front and back of the gate. Photo was dated.

Customer’s Signature

Date

Installer’s Signature

Date

GTO Pro SL-1000, Pro SL-2000 Installation Manual

Specifications and Main Features

Frequently Asked Questions

User Manual