GT-Lite GT-2PK-T8-SLH Assembly & Installation

WARNING:

TO AVOID RISK OF ELECTRICAL SHOCK,

SHUT OFF POWER BEFORE

Complete LED Lighting Solutions

Assembly & Installation: GT-2PK-T8-SLH | T8 LED Bulb (2pk) Ballast Bypass

▫

When using product, basic precautions should always be followed.

▫

Read and follow these instructions and heed all warnings.

▫

Carefully read and understand the information given in this manual

before beginning installation. Failure to do so could lead to electric

shock, fire, or other injuries which could be hazardous or even fatal.

▫

WARNING

Save these instructions and warnings.

INSTALLING OR SERVICING THIS FIXTURE

Compatible With:

SHUNTED

BALLAST

LAMPHOLDER

BYPASS

CAUTION

NON-SHUNTED

LAMPHOLDER

IF NOT QUALIFIED DO NOT ATTEMPT INSTALLATION

•Contact a certified electrician to install these bulbs if you are not properly qualified.

Risk of Electric Shock or Fire

•Risk of Electric Shock or is present when working with electrical components.

•Do not drill holes in the fixture that could affect the internal wiring.

Prevent Electric Wire Abrasions

•Do not expose wiring to edges of the fixture or other sharp objects. This can cause
abrasion and damage the wiring, greatly increasing risk of electrical shock or fire.

Fixture Compatibility

•These bulbs are should only be installed in properly bypassed 48” T8 fixtures

•This bulb is only compatible with ballast bypass fixtures. The bulb will not operate
correctly with any ballast.

•This lamp can be used with shunted and non-shunted lamp holders, but requires different
wiring schematics for each type of lampholder

•It is your responsibility to ensure that your fixture has been properly wired for this bulb.
If you are unsure, contact a qualified electrician or contact manufacturer.

Question/Comment/Missing Part?

Contact GT-Lite 1-800-865-6799

www.GTLEDLIGHTING.com

▫ Installation Booklet
▫ (2) T8 Ballast Bypass Bulbs

Assembly & Installation: GT-2PK-T8-SLH | T8 LED Bulb (2pk) Ballast Bypass

WARNING:

TO AVOID RISK OF ELECTRICAL SHOCK,

SHUT OFF POWER BEFORE

INSTALLING OR SERVICING THIS FIXTURE

KIT INCLUDES:

Complete LED Lighting Solutions

Question/Comment/Missing Part?

Contact GT-Lite 1-800-865-6799

www.GTLEDLIGHTING.com

• If the lamp or luminaire exhibits undesireable operation (buzzing, flickering, etc.)
immediately turn off power, remove lamp from the luminaire, and contact manufacturer.

• Risk of fire. Perform a visual inspection to ensure lampholders are not damaged or loose
before installing and turning on this lamp.

• If lamp does not light when the luminare is energized, remove lamp from luminaire and
contact lamp manufacturer or qualified electrician.

• Reliable operating temperature: -4°F to +113°F (-20°C to +45°C).

•These devices are not intended for use with emergency exit lights.

•This product may cause interference to radio equipment and should not be installed near
maritime safety commmunications equipment or other critical navigation or
communication equipment operating between 0.45 - 30MHZ.

CAUTION

1.TURN OFF POWER AT THE BREAKER OR FUSE PANEL.

TURNING OFF POWER AT THE WALL SWITCH IS NOT A SUFFICIENT SAFETY PRECAUTION

2. Double check the rating of the lamp (120-277VAC) matches the voltage of the current circuit

3. Check to see if the fixture is compatible with the bulbs. (Ballast Bypass, Shunted/Non-Shunted).

4. Check all wires for proper connection with no loose ends.

4. If Ballast is already bypassed, move on to step 5.
If ballast is not bypassed, see Diagrams 1, 2, & 3 and follow instructions on the following page.

5.Take out old bulbs

6. Install GT-2PK-T8-SLH bulbs into the new fixture

7. Turn Power back on and turn fixture on. If bulbs do not turn on, disconnect power
from fixture and proceed to troubleshooting section.

DIAGRAM 1

BULB INSTALLATION INSTRUCTIONS:

Bypass

Install

1. Turn Off Power. 6. Turn on power.

3. Cut all wires

attached to ballast.*

4. Connect one end of
fixture to line power.

5. Install LED tube.

2. Remove existing lamp.