GTE Industrieelektronik KMG-2000 Quick Start Guide

GTE KMG-2000 System Guide & Installation

Installation instructions
Installation must be performed by a qualified professional and must observe all local, sta te, national and European

regulations. Before starting installation, make sure that the product is in perfect condition. Laying, electrical
connections, and adjustments must be done to “Industry Standards”.

Packing materials (cardboard, plastic, polystyrene, etc.) are potentially dangerous. They must be disposed of
properly and kept out of the reach of children Do not install the product in an explosive environment or in an area
disturbed by electromagnet ic fi eld s.

The presence of gas or inflammable fumes is a serious safety hazard. Provide an over-voltage protection,
mains/knife switch and/or differential on the power network that is suitable for the product and conforming to
current standards.

The manufacturer declines any and all liability if any incompatible devices and/or components are in stalled that
compromise the integrity, safety, and operation of the product. Only original spares must be used for repair or
replacement of parts. The installer must supply all information regarding the operation, maintenance, and use of
individual components and of the system as a whole.

Maintenance
To guarantee the efficiency of the product, it is essential that qualified pr ofessionals perform maintenance at the

times and intervals required by the installer, by the manufacturer, and by current law. All installation, maintenance,
repair and cleaning operations must be documented. The user must store all such documentation and make it
available to competent personnel.

Warning for users
Carefully read the enclosed instructions and documentation. Th is product must be used for its intended purpose

only. Any other use is improper and therefore dangerous. The information contained herein and in the enclosed
documentation may be changed without no tice, and are in fact provided in an approximate manner fo r application
of the product. Easygates declines any and all liability in this regard.

GTE KMG-2000 Overview & contents

The KMG-2000 system is used to measure forces exerted by autom atic doors, gates & barriers used throughout
the door & gate industry. The unit incorporates an on-board memory facility to store results collected whilst testing
doors/gates to be later uploaded to computer to produce comprehensive reports.

The KMG-2000 suite contains the following components:­KMG-2000 – Force testing device including toughened carry case
CABLE – male to male USB cable
CD – Software CD containing USB drivers and KMG-2005 software program

GTE Manual – Printed copy of GTE’s own instructions for use of the device
* Certificate – Calibration/certification certificate for device (*If purchased)

(Please Note: Hardware/software requirements for connection of KMG-2000 to a PC are Windows operating system 95/98/ME/2000/ XP/VISTA
or Windows 7 PC with free USB port)

Optional Accessories

KMG-ARM – Extension set for measurements to EN12445 for gates (1 x 300mm, 1 x 500mm piece)

Physical Connection & Software Installation

Remove tester and components listed above from packaging and conne ct the KMG-2000 to a free USB port on
your computer. Insert the supplied CD-ROM in to your computers CD drive (if your computer does not have a CD
drive copy the contents of the CD to a USB flash drive or download the software directly to your computer using an
internet connection).Follow any on-screen prompts for installation of driver software and the KMG VD 2005
software package.

(For computers running Windows Vista, 7 or 8 it may be possible that the driver installation of the KMG-2000
device will fail at first installation of the program. If this occurs please re-start the computer and disconnect the
KMG-2000 device from the USB port. Following the re -start, re-insert the CD or re-start the installation program
and follow the on-screen prompts for installing the USB driver. Once complete, re-connect the KMG-2000 device
to the USB port and device installation should complete.)

PLEASE NOTE:

For computers running Windows 7 (or later) the latest version of KMG VD2005 (ver. 5.5) must be
downloaded and installed following the successful installation of the CD version supplied. To download the correct
version for operation with Windows 7 (or later) please visit http://www.gte-industrieelektronik.de/material/KMG-

VD2005-V5.5.exe