GST I-9301 User Manual

30303029 Issue 4.03

Features

 Electronically addressed. The address can be

modified in field.

 Built-in microprocessor processes messages

intelligently.

 Insulation technology for input signal, good

anti-interference ability.

 Cable checking.
 Plug-in structure.

Description

With a microprocessor, I-9301 Addressable Single I/O
Module can communicate with fire alarm control panel
(FACP), check power cut, control output and LED.

The module closes the output relay and illuminates the
LED when receiving start command from fire alarm
control panel.

Connection and Wiring

Terminals on the module are shown as Fig. 1.

9

10

15

16

8

7

2

1

D1

D2

Z1

Z2

V+ G

COM1

NO1 NC1

GST-LD-8301/I-9301

Mounting
Hole

Mounting
Hole

Mounting
Direction

Fig. 1

Z1,Z2:Connecting with loop of FACP,
polarity-insensitive.
D1, D2: Polarity-insensitive 24VDC power line.
V+,G:24VDC output terminals, supplying output contact
with +24V output signal . There is 24V output at V+ and
G no matter whether the module is started or not.
NC1, COM1, NO1: Normally closed or normally open
output terminals.

Recommended Wiring

1.5mm

2

or above fire cable for 24VDC power line,

1.0mm

2

or above fire cable for other terminals, subject

to local codes.

Installation

The module is simply plugged onto the base after
corresponding terminals are connected.

Conduit

Electric Box

Module

Conduit

B-9310
Back Box

Module

Fig. 2 Fig. 3
If the cable conduit is inside the wall, the base is

installed onto the electric box (Fig. 2). If the cable
conduit is on the surface of the wall, the B-9310 Back
Box is available.

Note the upward arrow for mounting direction (Fig.1).

Application

The module is designed to connect with the devices
controlled by fire alarm control panel, including smoke
exhauster, fan blower, and fire valve.

Address can be set through P-9910B programmer in
field, refer to P-9910B Hand Held Programmer
Installation and Operation Manual for specific
operation.

Mode of checking feedback signal can be set through
P-9910B programmer. After unlocking the programmer,
press Function and then number “4”, i nput “13” or “40”.
“13” means checking the feedback signal at any time,
“40” means checking feedback signal only in started
state. Press Program, if P appears on the screen, the
setting is successful.
 The module can directly drive a smoke exhauster
or fire valve (electrical tripping device). System
composition is shown in Fig. 4.

The Intelligent Solution

I-9301

Addressable Single I/O Module

548h/02

30303029 Issue 4.03

Fig. 4
 System composition for volt-free output contact
controlling field device is shown in Fig. 5.

Fig. 5

Note:
Don’t connect the module’s contact to the AC
control loop directly, preventing the strong AC
interference signal from damaging the module or
controlled device.

The module is not used for gas extinguishing
devices.

Specification

Operating Voltage Loop: 24V

Power: 24VDC
Quiescent Current Loop≤1mA Power≤2mA
Action Current Loop≤3mA Power≤15mA
Output Capacity

Output contact capacity is 24VDC/5A

Voltage output capacity is 24VDC/1A

Output Control Mode Relay normally open/normally closed

volt-free output
Addressing Electronically addressed
Addressing Range Occupying one address, selectable

within 1～242.
LED Red, flashes when polling, illuminates in

action.
Ingress Protection
Rating

IP30

Operating
Temperature

0℃～+49℃

Relative Humidity ≤93%, non condensing
Material and Color
of Enclosure

ABS, White (RAL 9010)

Dimension
(L×W×H)

120mm×80mm×39mm

Weight About 194g (with base)

Accessories and Tools

Model Name Remark

P-9910B Hand Held

Programmer

Supplied separately

B-9310 Back Box

Supplied separately

Limited Warranty

GST warrants that the product will be free from defects

in design, materials and workmanship during the
warranty period. This warranty shall not apply to any
product that is found to have been improperly installed
or used in any way not in accordance with the
instructions supplied with the product. Anybody,
including the agents, distributors or employees, is not
in the position to amend the contents of this warranty.
Please contact your local distributor for products not
covered by this warranty.

GST China
Gulf Security Technology Co., Ltd.

No. 80, Changjiang East Road,
QETDZ, Qinhuangdao, Hebei,
P. R. China 066004
Tel: [phone]
Fax: [phone]

[e-mail]
www.gst.com.cn

GST UK
Global System Technology PLC

Lion Court, Staunton Harold Hall,
Melbourne Road, Ashby de la Zouch,
Leicestershire, England LE65 1RT
Tel: [phone]
Fax: [phone]

[e-mail]
www.gst.uk.com

GST Dubai
Global System Technology PLC

PO Box 17998 Unit ZA04
JEBEL ALI Free Zone,
Dubai, UAE
Tel: [phone]
Fax: [phone]

[e-mail]
www.gst.uk.com

This document is subject to change without notice. Please contact GST for more information or questions.

Z2

Z1

GND

+24V

Electrical Tripping Device

COM1

Z1

G

D1

V+

D2

NO1

Z2

I-9301

Z2

NO1

D2

V+

D1

G

Z1

COM1

Controlled Device

+24V
GND

Z1
Z2

Control Input

I-9301