GST I-9300 User Manual

30303027 Issue 3.04

Features

 Working mode can be set to normally open,

normally closed and normally open cable monitor
through programmer.

 Electronically addressed. The address can be

modified in field.

 The built-in microprocessor processes messages

intelligently.

 Insulation technology for input signal, good

anti-interference ability.

 Plug-in structure.

Description

I-9300 Addressable Input Module is designed to receive
normally open or normally closed switch signal from fire
devices with coincidence functions, and transmits these
messages to fire alarm control panel (FACP) with
coincidence detection function. When a device of this
kind is activated, the module can send the output signal
through signal loop to FACP to alarm or activate relative
devices.

Connection and Cabling

Fig. 1 shows terminals on the module.

9

10

15

16

8

7

2

1

Mounting
Hole

Mounting
Hole
Mounting
Direction

GI1

Z1

Z2

GST-LD-8300/I-9300

65mm

Fig. 1

Z1,Z2:Connecting with loop of FACP,
polarity-insensitive.
I1,G:Connecting with volt-free normally open contact
(closed to activate and report alarm) of the device, it
can be set to normally closed or normally open cable
monitor.

Recommended Cabling

1.0mm

2

or above fire cable for each terminal. Subject to

local codes.

Installation

The module is simply plugged onto the base after
corresponding terminals are connected.

If the cable conduit is inside the wall, the base is
installed onto the Back Box (Fig. 2). If the cable conduit
is on the surface of the wall, B-9310 Back Box is
available.

Note the upward arrow for mounting direction (Fig. 1).

Fig. 2 Fig. 3

Application

The module is designed to connect with active devices
in field such as water flow switch, pressure switch,
position switch, signal valve and devices able to
transmit back switch signals.

Address and working mode can be set through GST
programmer, refer to P-9910B Hand Held Programmer
Installation and Operation Manual for specific operation.
Working mode is defaulted to normally op en (4), w hi le it
can be modified to normally closed (7) or normally open
cable monitor (1).
 Fig. 4 shows connecting the module with field
device with volt-free normally open contact. Working
mode is normally open (4).
 Fig. 5 shows connecting the module with field
device with volt-free normally closed contact. Working
mode is normally closed (7).
 Fig. 6 shows connecting the module with field
device with volt-free normally open contact requiring
cable monitor. Working mode is normally cable monitor
(1).

Fig. 4

I-9300

Addressable Input Module

I-9300

Z1 Z2

I1 G

Normally Open Contact
Field Device

Z1

Z2

Conduit

B-9310
Back Box

Conduit

Module

Module

Back Box

548h/01

30303027 Issue 3.04

Fig. 5

Fig. 6

Specification

Operating Voltage Loop 24V(16V~28V)
Average Current ≤1mA
Programming
Method

Electronically addressed

Code Range One address is within 1～242.
Indicator Red, flashes when polling.

Illuminates in action.
Ingress Protection
Rating

IP30

Operating
Temperature

0℃～+49℃

Relative Humidity ≤93%, non condensing
Material and Color of
Enclosure

ABS, White (RAL 9016)

Dimension
(L×W×H)

120mm×80mm×39mm

(with base)
Weight About 181g (with base)

Accessories and Tools

Model Name Remark

P-9910B Hand Held

Programmer

Order separately

B-9310 Back Box Order separately

Limited Warranty

GST warrants that the product will be free of charge

for repairing or replacing from defects in design,
materials and workmanship during the warranty period.
This warranty does not cover any product that is found
to have been improperly installed or used in any way
not in accordance with the instructions supplied with
the product. Anybody, including the agents,
distributors or employees, is not in the position to
amend the contents of this warranty. Please contact
your local distributor for products not covered by this
warranty.

GST China
Gulf Security Technology Co., Ltd.

No. 80, Changjiang East Road,
QETDZ, Qinhuangdao, Hebei,
P. R. China 066004
Tel: [phone]
Fax: [phone]
[e-mail]
www.gst.com.cn

GST UK
Global System Technology PLC

Lion Court, Staunton Harold Hall,
Melbourne Road, Ashby de la Zouch,
Leicestershire, England LE65 1RT
Tel: [phone]
Fax: [phone]
[e-mail]
www.gst.uk.com

GST Dubai
Global System Technology PLC

P.O. Box 17998 Unit ZA04
JEBEL ALI Free Zone,
Dubai, UAE
Tel: [phone]
Fax: [phone]
[e-mail]
www.gst.uk.com

This document is subject to change without notice. Please contact GST for more information or questions.

I-9300

Z2

Z1

Normally Closed Contact
Field Device

I1 G

Z1 Z2

Z1 Z2

I1 G

Normally Open Contact

Field Device

Z1

Z2

I-9300

4.7kΩResistor