GST GLM-154 User Manual

LCD DVR COMBO

(Model : GLM-154)

USER’S

MANUAL

Firmware Version 2.4
Revision Date : 2005. 03. 25

•INDEX

■CHAPTER 1 – System Structure

1.1 System Specification ----------------------------------------------- 4

1.2 Set and Accessories -------------------------------------------------- 5

1.3 External Organization of System ---------------------------------------6

■ CHAPTER 2 - Description

2.1 Front Panel ------------------------------------------------------- 7

2.2 Rear Panel ---------------------------------------------------- 8

2.3 Remote Controller -------------------------------------------- 9

■ CHAPTER 3 - Installation

3.1 Hard Disk Installation ------------------------------------------------ 10

3.2 Camera Connection ------------------------------------------------ 11

3.3 Monitor Connection ------------------------------------------------- 11

3.4 Network Connection ------------------------------------------------ 11

3.5 Alarm / Relay / PTZ Connection ------------------------------------------- 12

3.6 System initial START (Power Connection)-------------------------------- 13

※ Hard Disk Format ------------------------------------------------- 13

■CHAPTER 4 -Display

4.1 System Power ON --------------------------------------------------- 14

4.2 Select Screen Mode ------------------------------------------------- 14

4.3 Convert Screen Mode ------------------------------------------------ 15

4.4 Control PTZ / Focus Control --------------------------------------------- 15

4.4.1 PTZ / Focus Menu ---------------------------------------------------15

4.4.1.1 PTZ Control -------------------------------------------------------16

4.4.1.2 Focus / IRIS Control ------------------------------------------------16

4.4.1.3 PRESET Control ----------------------------------------------------17

4.4.1.4 Swing Control -----------------------------------------------------17

4.5 System Power OFF -------------------------------------------------- 18

■CHAPTER 5 -Search

◎ Go to Search ----------------------------------------------- 19

5.1 Search by Date/Time ------------------------------------------------ 19

5.2 Search by Event -------------------------------------------------- 20

1

•INDEX

■ CHAPTER 6 - Menu

◎ Go to Menu ----------------------------------------------------- 21

◎ Initial Menu Display ---------------------------------------------- 21

6.1 Display --------------------------------------------------- 22

6.2 Record ---------------------------------------------------- 22

6.2.1 Size/Rec. Rate/Quality ------------------------------------ 22

6.2.2 Timer Recording Setup ------------------------------------23

6.2.3 Motion Detection Setup -----------------------------------24

6.2.4 Alarm Recording Setup -------------------------------------- 24

◎ Time Recording Weekly Setup -------------------------------------- 25

◎ Partial Motion Region Setup ----------------------------------------- 26

6.3 Camera ---------------------------------------------------------- 27

6.3.1 Status/Title Setup ----------------------------------------------- 27

6.3.2 Covert/PTZ Setup --------------------------------------------- 27

6.3.3 Color Setup -------------------------------------------------- 28

6.4 AUDIO ------------------------------------------------------28

6.4.1 Audio Recording Setup ----------------------------------------- 28

6.4.2 Live Audio Setup ---------------------------------------------- 29

6.5 ALARM ---------------------------------------------------- 29

6.5.1 Alarm Input Setup ----------------------------------------------- 29

6.5.2 Relay Output Setup ---------------------------------------------- 30

6.6 SYSTEM -----------------------------------------------------30

6.6.1 Date/Time ----------------------------------------------- 30

6.6.2 Network Setup TCP / IP----------------------------------- 31 ~ 32

6.6.3 Buzzer Setup ----------------------------------------------- 33

6.6.4 Password -------------------------------------------------33

6.6.4.1 Administrator Password ---------------------------------33

6.6.4.2 Manager Password ------------------------------------- 34

6.6.4.3 Operator Password ------------------------------------ 34

6.6.4.4 Network Password ------------------------------------ 34

6.6.5 Disk Write Mode -------------------------------------------- 35

6.6.6 System Information -------------------------------------- 35

6.6.7 Factory Default --------------------------------------------- 35

2

•INDEX

■ CHAPTER 7 - Remote Agent

◎ System Requirement ------------------------------------------- 36
◎ DVR Remote Agent 1.0 Installation ------------------------------- 36 ~ 38

7.1 Monitoring

7.1.1 Function Introduction ---------------------------------------- 39

7.1.2 Screen Division Selection -------------------------------------- 40

7.1.3 PTZ Control ------------------------------------------------- 40

7.1.4 Selection Network ID ----------------------------------------- 40

7.1.5 AVI File Conversion ------------------------------------------- 41

7.1.6 Color Adjustment -------------------------------------------- 41

7.2. Search

7.2.1 Function Introduction ----------------------------------------- 42

7.2.2 Search Method ----------------------------------------------- 43

7.2.3 Search Option ----------------------------------------- 44 ~ 48

7.3. Setting

7.3.1 Connection ID Setup ------------------------------------------- 49

7.3.2 Option Setting ------------------------------------------------ 50

7.3.3 DVR Server Remote Setup -------------------------------------50 ~ 52

■CHAPTER 8 – Web Client --------------------------------------------- 53 ~ 54

3

1.1 System Specification

4

• Chapter 1 – System Structure

4 lnputAudio lnput

10/100BASE- TX EthernetLAN

Button or IR RemoconSystem Operation

Mono 1WSpeaker
4 lnput / 1 OutputAlarm / Relay
RS-485P/T/Z Control & Port

Composite Video (BNC x 1)Video Output

100/130(CR≥10)

Viewing Angel

[˚,U/D/L/R]

16Response Time [ms]

450Luminance [cd/㎡]
60Color Saturation(%)
600:1Contrast Ratio

1,024 x RGB x 768Resolution

32bit DSPCPU

?kgWeight

350(w)×315(H)×65(D)mm (Stand not included)Dimension

DC12V, 5A (Adaptor)Power

5~40˚C/ 20~80%RHOperating Temp and Humidity

-20~65˚C / 20~80%RHStorage Temp and Humidity

Auto- Rebooting, Auto- Scan and Recovery for Data System Recovery After Power Failure

Remote Pan/Tilt/Zoom/Focus/IrisRemote Control

Remote Live Viewing, Remote Playback and Remote File copy
Playback, Network Transmission, Recording (Triplex operation)

Remote Transmission

Supports the Setting of Motion Sensitivity per CameraMotion Detection

Setting Recording Schedule per cameraRecording Schedule

Continuous, Motion Detection and Sensor ActivatedRecording Modes

3~5Kbyte @352×240 (PAL :352×288)
5~10Kbyte @704×240 (PAL : 704×288)
6~16Kbyte @704×480 (PAL : 704×576)

Byte Size per image

MPEG4 (Modified)Compression Method

NTSC : 352×240, 704×240, 704×480
PAL : 352×288, 704×288, 704×576

Recording Resolution

30/25704×480

60/50704×240

120/100352×240

Recording

Speed

1/4 Channel ModeScreen Modes

Composite Video RJ45 x 4 or BNC x 4 (NTSC/PAL)Video Input

RTOSOS

80GBHDD

LCD PANEL

1.3 Set and Accessories

GLM-154 Set

Remote Controller

User’s
Manual

AAA Battery X 2

DC12V Adaptor

Power Cord

• Packing Components

5

Please confirm accessories when you open packing box.

Installation CD

ROM

Camera set (Optional)

• System Organization

1.4 External Organization of System

6

Remote Client PC

Image Printer

NETWORK

Alarm Sensor #1~4

Relay Out

GLM-154

Camera #1~4

Video In

Video Out

TCP/IP

Alarm
Input/Out

Remocon

Monitor

7

• Chapter 2 - Description

① Power : System Power On/Off.
② LED Indicator : Indicate System working Status

• POWER : System On/Off

• RECORD : Record On/Off

• NETWORK : Client Network Connect On/Off

• ALARM : Alarm Sensor On/Off

③ Channel Select Button : When Select Channel or Input Password
④ SCR Mode : When Select Screen Division Mode or Rotation Mode
⑤ Menu : Go to System Menu
⑥ Search : Go to Search Mode for Searching Recorded Video
⑦ PTZ/Focus : Go to Camera PTZ/Focus Control
⑧ Remote Controller Sensor Input (Refer to using of remote controller)
⑨ Search Controller & Volume Control :

Search Recorded video, Control Menu, PTZ/Focus and adjust volume of speaker
⑩ Enter : Press Enter to Apply Changing Setup
⑪ Return : Cancel Setup or Return Previous Mode

2.1 Front Panel

Tip

• Channel Selection Button is prior to SCR mode.

• When Remote Controller Sensor Input is blocked by something, it cause

1 remote controller do not work properly.

• When press any button, it operate with Beep Sound.

②⑤⑦⑨⑪

⑧

①③

④

⑥

⑩

VOL

8

• Description

① Video In : 4 Camera Connectable

(Reference to Page 60, GLM-154 PTZ available Camera Products)

② Monitor Out : Output DVR Video when connected AV Monitor

③ Ethernet (TCP/IP) : Connect Port for LAN Cable

(Possible to Remote Survey to Connect to Client)

④ Alarm / Relay / RS-485 : Connect Port for Sensor & Relay, PTZ (Pan / Tilt / Zoom)

⑤ DC Power Input Terminal : Power is Supplied by DC 12V Adaptor

2.2 Rear Panel

Tip

• When System Installation, Please after System Off, connect Rear Panel

• Please Power Supply Use Specific Adaptor

①

③

④

⑤

②

9

• Description

PTZ/IRIS
Mode

• Unused Button’s Description is Omitted.

• Every Button is Operated Same as Front Panel Button.

• Remote Controller can Operate when Remote Controller Sensor Input Part Reacted.

※Caution : If there are many DVRs at the same place,

they are operate together when press remote controller

Channel Select Button
(4ch Available, #1~4 Button)

POWER

System
ON/OFF

MENU: Open menu

RETURN

Cancel
Setup or
Return to
Previous

ENTER: Apply Setup Change

Change
Screen Mode

Open
Search Mode

Search Controller : Control Playback Option

(EX. Speed of Playback, Move on Menu,

1Control PTZ/Focus)

2.3 Remote Controller

① Jumper Setup Master or Slave

10

3.1 Hard Disk Installation

• Refer to Jumper Pin Setting on HDD Surface

• When HDD Installed, Fix jump as Master

1 and Connect Pin at the Left end of Jumper

!!Please use HDD which can supply higher than UDMA66.!!

※ Example of Samsung HDD Jumper Setup

• Chapter 3 - Installation

• Jumper Setup as Master or Slave refer to Explanation
of Surface Hard Disk

• Jumper is located at Hard Disk Data Cable or Rear

1 Side of Hard Disk

• Hard Disk is Installed, Setup as Master

1

‼ When Hard Disk changing, it must be serviced

after System Off (Power Button System Off).

If not, it’s a cause of Fatal Failure of HDD‼

11

• Installation

3.2 Camera Connection

Connect Camera at Multi-Jack Modular Port in Back Side Panel.

3.3 Monitor Connection

Connect Monitor Out of GLM-154 to Another Monitor Input

3.4 Network Connection

Connect Ethernet Terminal to Network System (Personal Computer etc)

Monitor

• Installation

12

3.6 Alarm, Relay and PTZ Connection

PTZ 14 Pin Cable

⑨ R+

⑩ R-
⑪ T+
⑫ T-

RS485

D+
D-

3.7 Power Connection

Connect DC Power Input Terminal and Specific Adaptor

DC12V Adaptor

① ③

②

①ALARM

Alarm Input Terminal ( “IN1, IN2, IN3, IN4”,GND )

Connect Sensor Input of Channel and GND Connect Ground cable

② RELAY

Alarm Output Terminal ( “NO, NC, COM”)
After Checking Alarm Output Type, Connect to NO (Normal Open) or NC (Normal Close)

“COM” : Connect Remainder ( Ground connector)

③ RS-485

Connect PTZ Camera ( “D+, D-”) : Connect PTZ Camera Control Line (Plus , Minus Terminal)

13

• Installation

3.7 System initial START

※ Caution : Hard Disk Format !!!

- If Do Not Formatted New Hard Disk , System Can’t Recognize the HDD.
So there’s the Same Situation without HDD. Please Format HDD when

Insert New HDD.

(Only Screen Display is Possible, Work Menu and Search are impossible)

2. New HDD Format

(Select Play , Backward Play Key)

3. System Start (Initial Mode)

1. Power On

※ 80GByte HDD Capacity

14

• Chapter 4 - Display

4.1 System Power ON

4.2 Select Screen Mode

CAMERA

2004/01/01

00:00:00

• Press Power Button to Start System

• After Checking Hard Disk, Input Your Password to

1 Operate

• Initial Screen View Mode is Quad Division Mode

1 and Recording Mode

Picture of Power On

after Finishing Installation

Tip

• Check System Condition using LED

POWER : Showing System On/Off
RECORD : Showing Record On/Off
NETWORK : Showing Client Connection Status
ALARM : Lighting when Sensor Alarm Activate

• Select One Channel among 4 Channels

• Move to One Enlargement Watch Mode when Quad Screen Division Mode

• Move to One Enlargement Watch Mode when Rotation Mode

• Each Channel Indicates Camera Name & Recording Status

• Present Time & Date display Central Lower Side of Monitor

15

• Display

SCR MODE

4.3 Convert Screen Mode (SCR MODE)

4.4 PTZ / FOCUS Control

• User can Select Watch Mode of 3 Kinds as followings

① Quad (4CH) Division Watch Mode

②Selected 1CH Watch Mode

③ 4CH Rotation Watch Mode

• Quad (4CH) Watch Mode is Initial Mode when System Start

• Control Camera PTZ (Pan/Tilt/Zoom) & Focus (Only Useable for Proper Camera)

• Press PTZ/FOCUS Button to Open PTZ Menu at Right-Under Side and Control by Search Controller

• Press PTZ/FOCUS Button Second Time to Open FOCUS/IRIS Menu and Control by Search Controller

Control Camera PTZ &
Focus by Search
Controller on PTZ Menu

Quad (4CH) Division
Watch Mode

Selected 1CH
Watch Mode

4CH Rotation Mode

PTZ/Focus Direction Key

VOL

Backward

Play

Play

Fast

Backward

Fast

Forward

Pause

① Control Camera Movement by “Faster”, “Slower”, “Backward Play”,

”Play” Button (Up, Down. Left and Right).

② Zoom In & Out by “Fast Backward”, “Fast Forward” Button.

③ Keep Press Button Make Continuous Movement.

16

PTZ CTL

UP

LEFT RIGHT

DOWN

FOCUS / IRIS CTL

UP

LEFT RIGHT

DOWN

• Press PTZ / FOCUS Button to Open PTZ Menu at Right-Under Side and Control by Search Controller

• When Press PTZ / FOCUS Button by Turns, Focus / IRIS, Preset, Swing Menu will Appear at

the Right-Under Side and possible to Control by Search Controller.

PRESET

NUMBER : 1

NUMBER CHANGE : UP/DOWN

SET : F1 GOTO : F2

SWING

MODE : PAN SWING

NUMBER CHANGE : UP/DOWN

FIELD CHANGE : LEFT/RIGHT

SET : F1 RUN : F2

4.4.1.1 PTZ Control

4.4.1.2 FOCUS / IRIS Control

① Control IRIS “Faster”, “Slower” Button.

② Focus On by “Backward Play”, “Play” Button.

③ Zoom In & Out by “Fast Backward”, “Fast Forward” Button.

④ Keep Press Button Make Continuous Movement.

• Display

4.4.1 PTZ / Focus Menu

① By PRESET Function, Possible to Setup Direction and Focus of PTZ Camera.

② After Selecting Position at PTZ Control Mode, Save Data at PRESET Mode.

③ Setup “NUMBER” from 1 to 128 by “Faster” & “Slower” Button.

17

4.4.1.4 SWING Control

① SWING Function Dedicate Each No. of Saved Preset and Swing as Pan or Tilt.

② Changing Mode by Backward Play Button.

Changing Setup by Faster, Slower Button.

PRESET

NUMBER : 1

NUMBER CHANGE : UP/DOWN

SET : F1 GOTO : F2

④ Save by Front Panel Key No.1 Button or F1 Button on Remote Controller.

⑤ To Move to Saved Location, Press Front Panel Key Button No.2 or F2 Button on Remote Controller.

SWING

MODE : PAN SWING

NUMBER CHANGE: UP/DOWN

FIELD CHANGE: LEFT/RIGHT

SET:F1 RUN:F2

③ PAN SWING MODE : Rotate Left , Right Side.

TILT SWING MODE : Rotate Up, Down Side.
START PRESET : Select Starting Point. (1~128)
END PRESET : Select End Point. (1~128)
SWING TIME : Select Halt Time as Each Point. (1~64sec)
SWING SPEED : Select Moving Speed of Camera. (1~64)

④ Save by Front Panel Key No. 1 Button or F1 Button on Remote Controller.

⑤ For Start SWING Mode, Press Front Panel Key No.2 or F2 Button on Remote Controller.

• Display

4.4.1.3 PRESET Control

18

• Display

4.5 System Power OFF (SHUTDOWN)

Tip

• System Log-On Possible ID : “Administrator”, “Manager”, “Operator” and “Network”

1. Administrator : Possible All Function Access (System On, Shutdown, Setup, Search)

2. Manager : Possible System On and Search

3. Operator : Possible System On

4. Network : Possible Connect by Remote Program

• Press Power Button to System Off

• Input Password and Press Enter

19

• Chapter 5 - Search

SEARCH

• Press Search Button and Log-In
Administrator or Manager

ENTER

RETURN

2004/01/01
00:00:00

>

⊙ Go to Search Mode

• Use Direction Key to Move Menu

• To Open Each Menu Press Enter

• Return to Previous.

(Move to Previous Menu or Exit Search

1 Mode and Return to Watch Mode)

Search Recorded Data

5.1 Search by Date/Time : Possible to Search Recorded Date & Time

① Move Cursor to Select Date of Calendar

(Recorded Date & Time are Indicated by Gray Color)

② Press Enter to Open Selected Date

③ Recorded Time Appear to Under Side

④ Press Enter Selecting Time

(One Scale is 15 Minute)

⑤ Menu Disappear and Play Recorded Video

• Showing Recorded Date & Time on Left-Upper Side

1 as Watch Mode.
1 Showing Playing Condition on Right-Under Side.

• Channel Selection Button in Watch Mode & SCR Mode

1 Button are the Same as Search Mode.

(But Menu, Search, and PTZ/Focus Buttons are Exception)

VOL

20

• Search

• Control Playing Video

① : Basic Playing Mode (Normal Speed (1X) Forward Playing)

② : Normal Speed Backward Playing

③ : Pause Video

④ : Fast Forward (2 ~ 64 Speed)

⑤ : Fast Backward (2 ~ 64 Speed)

5.2 Search by Event : Searching Video with Event Occurrence

Tip

• Alarm, Motion and System can be Select plural by Check (V)-(ENTER)

• To Change Setup, Press Enter and Press Direction Key
After Changing Setup, Press Enter to Exit.

※ Press Normal Forward / Backward Button in Pause, Move to Next/Previous Frame.

Alarm : Searching Alarm Event during the Selected

1 Period

Motion : Searching Motion Detected Event during

1 the Selected period .

Timer : Searching Schedule Change or Recording

1 Setup Change Event

System : Searching Power On/Off Event (etc.)

1 Concerned System Event

Set up Start & Finish Date for Searching Event

Event Lists Show on Below side of Window

• Date : Indicate Event Occurrence Order & Date

Time : Indicate Event Occurrence Time

Event : Indicate Event Contents & Camera No.

• Event Searching Method

① User can Search Event Using by Direction key

② Search Event to Press Enter on Selected Event

from Event Occurrence Time

③ Control Video is the same way as Time Mode Control

• The Search by Event is not Base on Video but Event Occurrence Time.

21

• Chapter 6 - Menu

•

ENT

RTN

•

⊙Go to Menu

① Press Menu Button on Front Panel in Watch Mode

② System Ask for Password

③ Input Password Using by Channel Select Button

1 [1][2][3][4])

④ After Input Password Press Enter to See Menu

Tip

• Initial Administrator, User and Network Password is 1234.

• Showing Password as Asterix (*)

• Method of Changing Password Æ (MENU->6.System->4.Password )

• Only Watch Mode can go to Menu.
(Search & PTZ/Focus Mode can’t move to Menu)

⊙Initial Menu Display

• Every System Setup can Change or Maintain

1 at Menu (6 Setup)

•

1. Move to Menu Using by

Up & Down Button

2. Adjust volume of speaker using by

Up & Down Button

To Open Detail Menu or to Apply Input

Return to Previous Menu or Return to Watch Mode

•

VOL

22

• Menu

6.2 Record : Setup Image Record

6.1 Display : Video Setup for Watch Mode

1. Date/Time : Date & Time Mark On/Off

2. Title : Camera Name On/Off

3. Status : Record status Mark On/Off
(Recording: Red, Pre-recording : Green)

4. Border : Border Line Mark On/Off
when Quad (4CH Division) Watch Mode

5. Border Color : Select Border Line Color
(White, Blue, Red, Yellow, Green and Gray)

6. Sequence Dwell : Setup Rotation Cycle Time
(1~60 Sec.) when 4CH Rotation Mode

at Watch Mode

7. De-interlace Mode : Remove Screen Spread on

High Resolution , Low Frame
※Only Applying When D1(704X480)

6.2.1 Size/Rec.Rate/Quality – Setup Recording Resolution, Compression Rate and Quality

- Camera : Indicate Camera No.

- Size : Resolution

- Rec.Rate : Compression Rate of Recording

- Quality : Quality of Recording Video

23

• Menu

Tip

Overlimit Recording Capacity

• Size : 352*240, 704*240 and 704*480

Rec.Rate : Possible to Select (1~30)

Quality : Possible to Select High, Low and Standard

• Indicate Frame No. of Control Size & Rec. Rate

• If Frame Over, Showing a Message

“Overlimit Recording Capacity’ and Impossible to

Change Size & Recording Rate

• When Setup, Please Refer to Below NTSC & PAL Type

NTSC : 352*240(120fps), 704*240(60fps), 704*480(30fps)
PAL : 352*288(100fps), 704*288(50fps), 704*576(30fps)

• Possible to Setup Size & Rec. Rate, Quality per Each Channel

• When Applying Change Setup, Press Enter,

1 When Cancel Change Setup, Press Return.

6.2.2 Timer Recording Setup – Record On/Off or Time, Motion Setup

• Camera : Indicate Camera No

• Record : Record On/Off

• Start : Recording Start Time (0~24 hr)

• Stop : Recording Finish Time (0~24 hr)

* Recording Time is between Start and Finish Time.

• Motion : Motion Detect Recording On/Off
(Record Setup must be ‘On’, when Motion Detection

1 Recording.)

24

• Menu

6.2.3 Motion Detection Setup – Motion Detection Area & Sensitivity

6.2.4 Alarm Recording Setup – Recording Setup for Alarm Activating

Tip

• Motion Setup Work by Time Schedule and Alarm Schedule Independently.

• Camera : Indicate Camera No. to Setup

• Sensitivity : Control Sensitivity (1~100)

Large No. is More Sensitive.

• Region : Setup Motion Detect Range

Entirely – Setup Entire Screen
Partially – Setup Partial Screen

• When Choose Region as Partially, Move to Partial

1 Range Setup. Press Enter After Partial Ran

g

e Setup

1 to Finish Region Setup.

• Pre-Motion Duration : Setup Pre-Motion Duration Time.

1 (1~5 sec)

• Post-Motion Duration : Setup Motion Detect Recording

1 Time after Motion Detected (5sec~3min)

• Camera : Indicate Camera No. to Setup

• Record : Setup Record On/Off when Alarm Activated

• Start : Setup Alarm Recording Start Time (0~24 hr)

• Stop : Setup Alarm Recording Finish Time (0~24 hr)

• Pre-Alarm Duration : When Alarm Recordin

g

, Setup

1 Start Recording Time before Alarm Activate (1~5sec)

• Post-Alarm Duration : Setu

p

Alarm Recording Time

1 after Alarm Activate (5sec~3min)

25

• Menu

⊙ Time Recording Weekly Setup

• Select All : Entire Region Select

• Deselect All : Cancel Region

• Save & Exit : Save Changing Setup & Exit

• Cancel : Cancel Changing Setup & Exit

Weekly mode Setup at Record Setup

①②

③④

⑤⑥

Scheduled Region Indicated Yellow

After “Deselect” Schedule, Activated Region by
Press ‘ENTER’ and Select Date & Time to Move
Cursor

After Selecting Region and Press “ENTER” Again
to Finish Schedule Setup (Red)

Setup of Date & Time Schedule is the Same way.
After Finishing Schedule Setup,
Press “Return” for Save & Exit

26

• Menu

①②

③

④

⑤

⑥

⑦

⑧

⊙ Partial Motion Region Setup

:Non-Activate Move Cursor :Activate Partial Setup Cursor :Partial Setup Finish Cursor :Non-Activated Region

Region Initial View

Move Cursor by Direction Key and
Press Enter at Selected Region

Press Enter again to see
Region as a Blue Color and
Setup Non-Activate Region

When Select Multi Region,
Using Direction Key in ② to
Expand Non-Activate Region

Press Enter to Select Multi
Non-Activate Region

Same Method as ④⑤, Possible
to Expand Non-Activated
Region

For Reducing Partial Region,
Cancel Non-Activate Region
in Same Way as ④⑤

When Finishing Partial
Region Setup, Press Enter
to Save & Exit

• Select All : Select Entire Region

• Deselect All : Cancel Region Setup

• Save&Exit : Save the Changes & Exit

• Cancel : Cancel Change Setup & Exit

27

• Menu

6.3 Camera : Setup Camera

Tip

6.3.2 Covert/PTZ Setup

6.3.1 Status/Title Setup – Camera Connection Status & Camera Name Setup

• Camera : Indicate Camera No. to Setup

• Status : Indicate Camera Status
of Connected or Disconnected

• Title : Setup Camera Name to Show Left Side

•Title Input Method :

Using Direction Key, Up & Down Keys for Alphabet A~Z, Numerical No. 0~9

1 Left-Right Keys for Moving another Letter.

• Camera : Indicate Camera No. to Setup

• Covert : Setup Covert On/Off
*What’s Covert?

When Covert On Watch Mode, Video Display is

1 Hidden, but Recording is On.

• PTZ Address : Select PTZ Camera Address

• PTZ Protocol : Select Kind of PTZ Camera

• Baud Rate : Setup PTZ Communication Speed

(2400, 4800, 9600 BPS)

Samsung(MRX-1000), HoneyWell(GC/GMC-755 Zoom)
Kalatel(KTD-312), Panasonic(WV-CS850),
Panasonic(WV-CSR604), PELCO-D, PELCO-P,
Sensormatic-ADPT8, Vicon(surveyor99), Sunin DSC-230
D-MAX ,HoneyWell(GC-655N)

※PTZ Available

Camera

28

• Menu

6.3.3 Color Setup – Control Video Color

6.4 Audio : Setup Audio

Tip

• User can Listen Saved Audio with Saved Video

• Audio Check in Search is Possible Only Normal Speed (1X) Forward

1 Playing at 1CH Mode (Audio Recorded Channel)

• Camera : Indicate Camera No. to Setup

• Bright : Control Monitor Bright

• Contrast : Control Monitor Contrast

• Color : Control Monitor Color

• Tint : Control Monitor Tint

* All Setup Possible to Control 0~100

6.4.1 Audio Recording Setup – Audio In Setup

• Camera : Indicate Camera No. for Setup

• Audio Rec. : Setup Recording On/Off from External

1 Audio In Terminal

• Audio Ch. : Setup Audio In Terminal Channel &

1 Audio Output Camera

29

• Menu

6.4.2 Live Audio Setup – Audio Out Setup

• Live Audio : Audio Output ON/OFF
Live Audio Output from Audio In Terminal

• Monitoring Ch. : Select Channel for Audio Output

1 Number 1~4 Audio in

• Network Audio

①Enter “4.Audio -> 4.2 Live Audio Setup” at the Menu.
②Select “One-way’ or ‘Two-way” at the Network Audio.

6.5 Alarm : Setup Alarm & Relay

6.5.1 Alarm Input Setup – Alarm Sensor Setup

Tip

• Alarm : Indicating Alarm Input Terminal No.

• Status : Alarm Sensor Connection Status
of Connected or Disconnected

• Camera : Input Camera No.1~4 of connecting Alarm

• Type : Alarm Sensor Type (Normal Open or Normal Close)

• Generally Alarm Sensor can be Divided Two Types.

1. Normal Open Type : Open Sensor Electrically and activated when Signal is Connected.

2. Normal Close Type : Close Sensor Electrically and activated when Signal is Disconnected.

③ One Way : Transfer Audio from DVR to Remote Client which is possible to receive Audio with video

④ Two Way : Communicate Audio between DVR and Remote Client which is Possible to tranceiver

Audio and DVR Server.

⑤ Network Audio Possible to Operate even Live Audio Off.

30

• Menu

6.5.2 Relay Output Setup – Alarm Relay Setup

6.6 System : Basic Environment Setup

Tip

• Alarm : Indicate Alarm Input Terminal No.

• Relay Out : Setup Relay Connect with Alarm Sensor

• Mode : Setup Reacted Relay as Latched

or Transparent Mode

• Duration : Setup Reacted Relay Time

1 (5sec~5min or Until key-in)

• Relay Type : Setup Relay Type Normal Open

or Normal Close

• Latched / Transparent

Latched – When Sensor Alarm Activated, Relay Reacted in Setup Duration
Transparent – Relay Reacted Temporary During Sensor Alarm Activate

6.6.1 Date/Time – Date & Time Setup

• Date : Setup Present Date (YYYY-MM-DD).
(If Time Setup to Past Date, Ask Delete Data for the Past Date.

NO->Date/Time No Change, YES->After Delete Past Data and Change Date/Time )

• Date Format : Select Date Output Type (Ex: 2004-00-00, 2004/00/00)

• Time : Setup Present Time

• Time Format : Setup Time Type as 12 Hour Base or 24 Hour Base

• Daylight Saving : Appling Summer Time

• MENU

<DHCP ON, DDNS OFF> <DHCP ON, DDNS ON>

<DHCP OFF, DDNS OFF> <DHCP OFF, DDNS ON>

31

※ If your network connect at the router, please must port forwarding.

Otherwise you can't receive the service well.

• Press the NEXT button and progress the step.

•Don’t change the DDNS name because it is fixed the domain name.

• IP Address : Input IP Address

• Gateway : Input Gateway IP for Internet Server

• Subnet Mask : Input Subnet Mask IP

• Network Speed : Setup Network Speed
(Network Speed Depend on Network Status)

※ if Change Network Setup, New Change Apply

when after Rebooting.

6.6.2 Network – Setup TCP/IP

• MENU

Possible to Confirm IP Address for the
DVR at the System Information.

DDNS

DDNS(Dynamic DNS): You can connect the DVR by the fixed domain
name(ex.00115f000001.dvrlink.net) at client or Web without entering the IP address.

1. Enter to ‘6.System -> 6.2 Network' on the menu.

2. Setup DHCP On or Enter the IP address.

3. Setup DDNS ON and reboot.

4. Enter to ‘6.System -> 6.6 System information’on the menu.

5. Confirm the MAC address.

6. The domain name is "MAC address.dvrlink.net".
EX) If Mac Address is 00-11-5f-00-b5-a7, the domain name is "00115f00b5a7.dvrlink.net"

7. If you connect by "00115f00b5a7.dvrlink.net" at client program or Web, you can connect the DVR.

※ 1. If your network connect at the router, please must port forwarding.

2. Please, you must enter the exact IP address, DNS Server, Gateway, Subnet Mask.

3. Please you must connect the DVR at External Network.

If you don't follow 1,2,3 , you can't receive the DDNS service.

DHCP

① Enter to ‘6.System -> 6.2 Network’ on the Menu.
② Setup DHCP On/Off.
③ DHCP Off : User Input IP Address by Himself.
④ DHCP On : After DHCP On, Reboot the System.

⑤ Can see the setup IP automatically at the system information.

※ DHCP (Dynamic Host Configuration Protocol) : Indicate IP Address for the DVR
Automatically.

32

Fixed MAC address of the DVR

※ If you use the DDNS, there is no
necessity to enter again the IP Address
every connection..

33

• Menu

6.6.3 Buzzer Setup – Setup Key Sound to Speaker

• Alarm Input : Alarm On/Off when Alarm Activate

• Videoloss : Alarm On/Off when Camera Disconnected

• Disk Full : Alarm On/Off when Hard Disk Full

• Disk Error : Alarm On when Hard Disk Error

• Key Input : Setup Key Input Sound

6.6.4 Password : Setup Password

6.6.4.1 Administrator Password – Setup Menu & System On/Off

• Current Password : Input Current Password (Initial Password or factory password : 1234)

• New Password : Input New Password

• Re-enter the Password : Re-Confirm New Password

• Save&Exit : Applying New Password

34

• Menu

6.6.4.2 Manager Password – Possible System On & Search, But Can’t Change Setup

6.6.4.3 Operator Password – Possible System On, But Can’t Change Setup and Search

• Current Password : Input Current Password
(Initial Password : 1234)

• New Password : Input New Password

• Re-enter the Password : Re-Confirm New Password

• Save&Exit : Applying New Password

• Current Password : Input Current Password
(Initial Password : 1234)

• New Password : Input New Password

• Re-enter the Password : Re-Confirm New Password

• Save&Exit : Applying New Password

6.6.4.4 Network Password – Setup Remote Connection Program Password

• Current Password : Input Current Password
(Initial Password : 1234)

• New Password : Input New Password

• Re-enter the Password : Re-Confirm New Password

• Save&Exit : Applying New Password

35

• Menu

6.6.5 Disk Write Mode – Setup Hard Disk

6.6.6 System Information – Product information (

Version etc)

• S/W Version : Indicate Software Version of the Product

• H/W Version : Indicate Hardware Version of the Product

• Video Signal Type : Indicate Video Signal Type

• Disk Size : Indicate Hard Disk Capacity

• Number of HDD : Indicate Present Installed HDD No.

• IP Address

• MAC Address

6.6.7 Factory Default – Every Setup Initializing

• Press Enter to Start Initialize

• Showing Warning Message and Press OK to Run Initialize

• If do Factory Default, Every Setup is Initialized, but

1 Saving Image is Not Erase.

• Disk Overwrite : Overwrite Permission when

1 Hard Disk Full

O N: Overwrite Hard Disk from Oldest Data
OFF: When Hard Disk Full, Stop Recording and

1 Buzzer Activate (Refer to Menu 6.3 Buzzer Setup)

• Disk Initialize Now : Refreshment Hard Disk
All Recorded Data Deleted

• When Disk Initialize, Alarm Message Showing.

1 Select “Yes” to Start Initialize Disk.

※ When Change Disk Overwrite ON/OFF Mode, the Change will be Applied from Changing Time.

For Example When Overwrite On Mode & HDD Full, Change to Overwrite Off Mode and then it
will be Applied New Data. Fill HDD Full after Changing Time.

• System Requirement

① Main Board (CPU): Celeron 500-700(Minimum), Pentium 4 recommend
② OS: More than Windows 98,DirectX 7.0A
③ Memory (RAM): More than 128 M
④ VGA: Overlay YV12 Format Graphic Card

All Radeon, Nvidia (Above Geforce) Matrox (Above G400) Compatible Video Card

※ Above DIVX Codec 5.1 (When Use Media Player)

• DVR Remote Agent 1.0 Install

① Open CD-ROM Drive and Run DvrRemoteAgentSetup.exe and then display as following

② Close All Running Software and Press Next for next step

36

• Chapter 7 - Client

③ Ask designating Folder to Install DvrRemoteAgent 1.0,

Recommend Basic setup c:₩program files:₩DvrRemote Agent 1.0
Click Next

④ Showing Progress of Copy of Files

⑤ Appear DirectX 7.0a Install Menu. If DirectX Version Lower than 7.0a, Press Yes to Start Install

37

• Client

⑥ When Finishing Installation, System must be Restarted. Click ‘Yes’

⑦ Finish DvrRemoteAgent 1.0 Program Installation

38

• Client

①

②

39

• Client

⑤

③

④

⑥

⑦

⑧

⑪

⑫

⑨

⑩

7.1 Monitoring

7.1.1 Function Introduction

① Main Screen Image : Showing Present Surveillance Camera Image

② Camera Select Button : Indicate Connected Camera Number

& Select Image to Click Camera Number

③ Hide/Exit : Hide DVR Client Window or Exit Program

④ Time Output : Showing Present Time & Date

⑤ Search : Move to Search Mode to Play Video

Setup : Move to Setup to Change Network Setup or Option

⑥ I/D Selection : Select I/D (identification) to Connect Server

⑦ Connect : Connect Server (GLM-154)

Disconnect : Disconnect from Server

⑧ Screen Division Selection : Change Screen Division Mode
⑨ Save by AVI file : Transmission Live Image Save by AVI File
⑩ Color Adjustment : Adjust Color of Live Transmission Image
⑪ PTZ Control Button : Control Camera PTZ (Pan /Tilt / Zoom) & Focus
⑫ Exit : Exit DVR Client

40

• Client

• P/T/Z Controller : P/T/Z Control of Camera by Four direction Keys

• FOCUS/ZOOM Select Button : Focus or Zoom Control by (+),(-) Button

• (+), (-) Control Button : Focus or Zoom Control

7.1.2 Screen Division Selection

• 1*1 View : Showing One (1) Video which User Selected
(Selection Video by Camera Selection Button)

• 4*4 View : Quad Screen Division Mode

• Scenario View : One Large Screen Mode Showing One by One (1*1 View)

1 Depend on User Selection Time (Not Work Screen Division Mode)

• Full Screen View : Present Video Move to Full Screen Mode

Mouse Double Click when Return Previous

*Mouse Double Click Make the Same Function as Full Screen.

7.1.3 P/T/Z (Pan, Tilt and Zoom) Control

7.1.4 Selection Network I/D

Network

Information Icon

• Select I/D to Connect Server.

• I/D can be Add, Change and Delete at Setup

• Click Network Information icon to See a

1 Popup Window for Connected Server I/D,
1 IP and Port Information.

41

• Client

• Click AVI Conversion Button to start AVI File Conversion

• During AVI Conversion Showing a Message and before Click “Stop” Save AVI File continuously

• Press “Stop” to Open Designating File Name & Saving Location, and Save AVI File

• Saved AVI File can Open Ordinary Moving Picture Player

• Moving Picture Player Codec Version is Above Divx 5.1.

7.1.5 AVI File Conversion

7.1.6 Color Adjustment

• Click Controller Possible to adjust Color

• Change Brightness, Contrast and Saturation from 0 to 100

• Click OK to Finish Changing Setup

• Client

42

①

③

④

⑤

⑥

⑦

⑧

②

7.2 Search Mode

7.2.1 Function Introduction

① Search Screen : Playing Selected Video

② Search Bar : Search & Indicate Camera Recording Situation by Time Bar

③ LIVE : Return to Watch Mode

SETUP : Open Setup to Change Network Setup or Option

④ Screen Division Selection : Change Playing Screen Division Mode

⑤ SEARCH Option : Backup Video or Search Event

⑥ Camera Selection Button : Select Camera at the 1*1 View

⑦ Quick Search : Find Image to Designate Date & Time

⑧ Search Controller : Control Playing Video

43

• Client

②

①

③④

⑤

⑥

7.2.2 Search Method

① Indicate 0~24 Hour

② Indicate Recording Situation (Blue : No Record, Yellow : Recorded Image at the Time)

③ Search Bar : Select Video to Drag Mouse Search Controller in Recorded Area

④ Indicate Camera Channel to Confirm Camera Recording Situation

⑤ Refreshment Recording Information Situation Window by Camera Channel

⑥ If Connected Channel is 5 or More, Another Channel will be Scroll.

Click Date and Select
Date on Calendar

Play Video as Normal
Speed (1X)

Stop Play Video

Program Exit

Search Bar will Move

if input Date & Time

44

• Client

③ Save Image

①Backup

②Backup Play

⑤ Log Search

⑥Event Viewer

④ Print Image

7.2.3 Search Option

①Backup – Backup Image from Server to Remote PC

• Backup Time : Designate Backup Time (Now or Later)

• Designate Backup Date & Time when Later

•Source :

Designate Backup Image Data Length to input

Start Time & End Time.

• Channel : Check Camera Channel for Backup

• Select All or Deselect All

• Press OK to Open Backup Status & Start Backup.

• When Finish Backup, Back Status Window Disappear & Backup Data Save at Hard Disk

1 Root Folder in Remote PC.

45

• Client

Tip

①

②
③

④

⑤

② Backup Play (DVR Player) – Transfer to DVR Player

① Showing Image (Possible to Only 1*1View Mode)

② Backup File Open to Play First Video

Ex. : ch02_04131730_04131735.rec ( Backup File for # 2 ch. Apr.13, 17H30M ~17H35M )

③ Indicate Present Playing Video Camera Channel No.

④ Indicate Present Time & Date and Possible to Search Time & Date

⑤ Search Controller : The Same Way of Previous Search

• This Mode is possible to only 1 vs 1 View Mode

• Backup Play Setup in Search Mode is the Same as DVR Player,

so it can be Run Independently without Running Remote Program.

46

• Client

③ Save Image – Capture Image & Saving Image at Hard Disk or Removable Disk

• Click “Save Image” icon during Playing Video

• Designate File name ( File Type : JPG or BMP) and Location and Finally Press Saving

• Conversion and Saving Image from Remote Viewer

③ Print Image – Present Image Capture and Print Out Image

• During Play Video, Click “Print Image”

• After Selecting Printer, Start Image Printing

• Print Out Remote Viewer Image

47

• Client

③ Log Search – Find Video Centering around Event Log at Server

① Search Range : For Event Output at the Below Window, input Start Time and End Time

at the Selected Date to Search Event When Press Search Button

② No : Indicate Event Log Order No. ( Max Event Log No. of 1 Page is 100 )

③ CH : Indicate Event Occurred Camera No.

④ Date/Time : Indicate Event Occurred Time & Date

⑤ Description : Indicate Event Detail Description

⑥ Left Direction Key : Move to Previous Page

⑦ Page : Move to Next Page

⑧ Right Direction Key : Move to User Select Page

⑨ Go to Timelane : After Select Event, Move Search Bar in Search Mode

⑩ OK : Return to Search Main to Play Event Image

②③

④

⑤

①

⑥⑧ ⑦ ⑨ ⑩

48

• Client

④Event Viewer – Showing Present Event in Server & Find Image

① No : Indicate Event Occurred Order No.

② CH : Indicate Event Occurred Camera No.

③ Date/Time : Indicate Event Occurred Time & Date

④ Description : Indicate Event Detail Description

⑤ Go to timelane : After Select Event, Move Search Bar in Search Mode

⑥ OK : Return to Search Main to Play Selected Event Image

①

②

③

④

⑤⑥

49

• Client

① ID Status : Indicate Present Saving ID & ID Information

② Name : Input Name to Add or Amend ID

③ IP Address : Input IP Address to Add or Amend Server

④ Port : Indicate Port No.

⑤ ID : Input ID for Connecting Server

⑥ Password : Input Password for Connecting Server

⑦ New : Click to Input New ID Information

⑧ Add : After Input All ID Information, Add ID Information at ID Status

⑨ Modify : After Amend All ID Information, Applying Change ID Information

⑩ Remove : Selected ID Delete at ID Status

⑪ Option : Each Option Setup Change

⑫ System Setup : Setup DVR Server from Remote Client, Only Possible when Connected Administrator

7.3.1 Connection ID Setup (Initial ID & Password is “NETWORK” & “1234”)

7.3 Setting

①

③
④

⑤
⑥

⑦

⑧

②

⑨⑩

⑪

⑫

50

• Client

7.3.2 Option Setting

① Receive Event : Select Kinds of Event as Multiple. Remote Client Only Receive Selected Event.

(System, HDD, Alarm, Video, REC)

② Screen Switching Interval (sec) : During the Monitoring, Select Screen Rotation Interval Time

(From 1 sec. to 300 sec.)

③ Live Audio Monitoring Channel : Select Channel for Listening Audio at Remote Among 4Ch Audio.

④ OSD Display : Select Screen Information. (Name, Date, Resolution)

⑤ Saving Directory : Designate Remote PC Backup Image Saving Folder.

Tip

7.3.3 DVR Server Remote Setup

• Click DVR System Setup Tap, Password Input Window Open

After Input Password, Setup Window Pop-up.

• DVR System Tap Indicated Only when Connect as Administrator.

• DVR System Setup Possible to Control Almost Every Setup at the Remote.

• When Activate Setup or Changing Setup at the DVR Server,

1 It’s Impossible to Change Setup at the Remote.

• During System Setup at the Remote, DVR Server Setup Start Make to

1 Close Remote System Setup Automatically.

• When Change DVR Setup at the Remote Client, DVR Server Setup must be Non-Activated.

• Administrator ID Max 1, Connectable No of People Max 4 (Manager, Operator and Web-Client)

• Remote Connection ID Authority

- Administrator : All Authority for Remote & Possible to Change DVR System Setup

- Manager : All Authority for Remote, But Impossible to Change DVR System Setup

- Operator : Monitoring & Setup For Live Screen

- Web Client : Only Live Image Monitoring

• Max 4 People Connection Including Every ID, Administrator ID Supply Only One.

51

• CLIENT

• Status/Title Setup

- Setup for Each Camera
(Connection Status or Camera Name).

•Color Setup

- Setup Color for Each Screen.

• Covert/PTZ Setup

- Setup Each Camera Covert

1 Function & PTZ Protocol.

Tip

• Refer to DVR Server Setup for Each Setup Detail.

①Record Setup

• Record Size/Rate/Quality Setup

-Setu

p

Each Channel

1 Resolution & Compression Rate.

• Timer Recording Setup

- Setup Time Schedule for Each Channel.

• Alarm Recording Setup

- Setup for Alarm Recording.

• Motion Detection Setup

- Setup for Motion Detection Recording.

②Camera Setup

52

• CLIENT

③Audio Setup

• Audio Recording Setup

- Setup for Each Channel Audio Recording.

• Live Audio Setup

- Live Audio & Two Way Audio Setup for Server.

④Alarm Setup

• Alarm Input Setup

- Setup for Each Channel

1 Alarm Connection & Type.

•Relay Output Setup

- Setup for Each Channel

1 Relay Connection & Mode.

⑤ System Setup

•System Info

- Possible to Watch DVR System

Status.

• Buzzer Setup

- Setup DVR Buzzer Sound On/Off.

• Password Setup

- Change Password for

1 Administrator, Manager, Operator.

• Disk Write Mode

- Setup DVR HDD Overwrite On/Off.

•Connection Status

- Indicate Currently Connected All

1 Remote Client Connection Status.

53

• CLIENT

8. WEB Client

• WEB Client Connection

① Input IP Address for DVR Server at the Internet Explorer Address Input Place.

② When Appear Active-X install Message, Please Click Confirm or Continue.

③ Showing Web Client Window at Internet Explorer.

④

Click Connection Button and Pop-up ‘Log In’ Window.

54

• CLIENT

⑤ IP Address (or URL) : Input DVR IP or URL Address

Port : DVR Client Connection Port is 6100
ID : Select ID (Administrator, Manager, Operator).

(No Difference Authority on Web Client.)

Password : Input Password.

⑥ Only Possible to Monitoring Live Video As soon as Connection.