Head-End Station STC 160
4 x AV Connection Panel
HAV 470
English
Notes on the Assembly Instructions.
As well as this supplementary Assembly
Instructions, the Assembly Instructions for the
STC
160
apply.
GSS
Grundig SAT Systems GmbH
Beuthener Strasse 43
D-90471 Nuremberg
Phone: +49 (0) 911 / 703 8877
Fax: +49 (0) 911 / 703 9210
E-mail: info@gss.de
Internet: http://www.gss.de/en
Contents
1 Safety regulations .......................................................................................3
2 General information ....................................................................................4
2.1 Scope of delivery ..........................................................................4
2.2 Meaning of the symbols used ..........................................................4
2.3 Technical data ...............................................................................4
2.4 Description ...................................................................................5
Connection variants .......................................................................5
4 x Cinch AV AV socket P1000 ............................................5
AV socket P1000 4 x Cinch AV ............................................5
Cinch AV + AV socket P2000 AV socket P1000 ......................5
Block diagram ...............................................................................6
3 Installation ..................................................................................................6
3.1 Installing the connection panel ........................................................7
3.2 Connecting the connection panel .....................................................8
Feed-in of external AV signals into quadruple modulators ..............8
Conversion of internal AV signals to ASI or LAN ...........................8
Combination of external and internal signals ...............................9
3.3 EMC regulations ..........................................................................10
4 Final procedures ........................................................................................11
- 2 - HAV 470
1 sa f e t y r e g u l a t i o n s
• The standards EN/DIN EN 50083 resp. IEC/EN/DIN EN 60728 must be
observed.
• Do not perform installation and service work during thunderstorms.
• Assembly, installation and servicing should be carried out by authorised
electricians.
• Switch off the operating voltage of the system before beginning with assembly or service work.
• Avoid short circuits!
• Observe the relevant standards, regulations and guidelines on the installation and operation of antenna systems.
• To ensure electromagnetic compatibility, make sure all connections are tight
and the covers are screwed on securely.
• No liability is accepted for damage caused by faulty connections or inappropriate handling of the device.
Check the head-end station according to the safety instructions listed in their
assembly instruction.
Take precautions to prevent static discharge when working on the device!
Electronic devices should never be disposed of in the household rubbish. In
accordance with directive 2002/96/EC of the European Parliament and the
European Council from January 27, 2003 which addresses old electronic and
electrical devices, such devices must be disposed of at a designated collection
facility. At the end of its service life, please take your device to one of these
public collection facilities for proper disposal.
- 3 - HAV 470
2 ge n e r a l i n f o r m a t i o n
2.1 sCo pe of d e livery
1 Connection Panel HAV 470
4 Triple Cinch cable
1 26 pin ribbon cable
1 Brief assembly instructions
2.2 meani ng of t h e sym b ols us e d
Important note
—> General note
• Performing works
2.3 teChniCal da ta
The devices meet the following EU directives:
2006/95/EC, 2004/108/EC
The product fulfils the guidelines and standards for CE labelling (page 12).
Unless otherwise noted all values are specified as "typical".
Audio Inputs:
Impedance: .................................................................................. 47 kΩ
Audio level: ...............................................................................0.5 V
Eingänge Video:
Impedance: ....................................................................................75 Ω
Video level:....................................................................................1 V
Anschlüsse:
CVBS video connectors (Cinch): ............................................................4
Audio connectors (Cinch): ...............................................................4 x 2
AV connectors (26-pin socket):................................................................2
rms
pp
- 4 - HAV 470
2.4 des Cription
The quadruple AV connection panel HAV 470 connects 4 analogues audio
and video signals from modules with AV 26 pin sockets with modules with
cinch sockets.
The Cinch sockets are permanently
connected to the AV socket P1000.
Via DIP switches the contacts of the
AV socket P2000 can be connected
individually to AV socket P1000.
P2000
12x
P1000
Audio
Audio
Video
Audio
Audio
Video
Audio
Audio
Video
Audio
Audio
Video
Audio
Video
P2000
Audio
Video
P1000
ConneC tion varia nts
4 x Ci n C h av av s o C ket p1000
Feed of external AV signals into the quadruple modulators HFM 470, HMM
470 (OIRT), HMS 470 (OIRT), HMS 480 (OIRT) or HMM 480 (OIRT).
av soCke t p1000 4 x CinCh av
Feed of AV signals of the modules HDC 470 CI AV, HDC 480 CI AV, HDCT
460 AV, HDCT 461 AV into the modules HDE 164 or HDC 166.
CinCh av + av so Cket p2000 av so Cket p1000
– 1…3 cinch AV signals and 3…1 AV signals of socket P2000 can be output
at P1000.
– Video signals of socket P2000 combined with cinch audio signals can be
output at P1000.
- 5 - HAV 470
bloCk d i agram
P2000
1 2 34 5 67 8 910 11 12
1 2 34 5 67 8 910 11 12
P1000
You can find the current
The
AV connection panel
end station.
1 2 3 4 5 6 1
AUS/OFF
EIN/ON
ON ON
Video
Video
Audio
Audio
Audio
Audio
VideoAudio AudioVideoAudio AudioVideoAudio Audio
Audio
Video
Audio
Video
Video
P2000
P1000
VideoAudio Audio
1 23
Audio
Audio Video Audio Audio Video Audio Audio Video Audio Audio
assembly instructions
2 3 4 5 6
Video
Video
Audio
Audio
Audio
Audio
4 56 7 89 10 1112
on the website "www.gss.de/en".
is designed exclusively for use in the STC 160 head-
3 in s t a l l a t i o n
– Ensure the head-end station is mounted so it will not be able to vibrate.
Avoid, for example, mounting the head-end station onto a lift shaft or any
other wall or floor construction that vibrates in a similar way.
– Before installing or changing a module, switch off the head-end station or
unplug the power cable from the mains power socket.
– Take measures to protect against ESD!
• Open the housing of the head-end station in accordance with the assembly
instructions for the STC 160.
- 6 - HAV 470
3.1 installi ng the C onneCt ion panel
– When installing a connection panel, make sure that it is inserted between
signal source and signal load in the short grooves without contact strip on
the board at the rear wall of the housing.
• Open the housing of the head-end station in accordance with the assembly
instructions for the STC 160.
• Open the locking device A in the direction of the green arrow.
A
• Insert the connection panel in a shorter groove B between two module
slots and gently slide it into the head-end station until it locks C.
• After installing the connection panel close the locking device A in the direction of the red arrow.
B
C
A
B
- 7 - HAV 470
3.2 Con neCting the C o n neCti on pa nel
Video
Audio
Audio
P2000
P1000
Video
2 3 4 5 6
Audio
Audio
Video
Audio
Audio
Video
Audio
Audio
1 2 3 4 5 6 1
AUS/OFF
EIN/ON
ON ON
VideoAudioAudio
VideoAudioAudioVideoAudioAudioVideo Audio Audio
The possible connections depend on the usage of the AV connection panel (see
page 2).
Via the DIP switches the individually contacts of P2000 can be connected to the
P1000 and the cinch sockets. Connect only needed contacts. Avoid parallel connections of sources and sinks.
feed-i n of e x t ernal av signal s into q uadr u ple m odulat o rs
4 x Cinch AV AV socket P1000
Feed of external AV signals into the quadruple modulators HFM 470, HMM
470 (OIRT), HMS 470 (OIRT), HMS 480 (OIRT) or HMM 480 (OIRT).
• Connect the external devices via cinch cables to the cinch sockets of the
module.
• Connect AV socket P1000 to the AV socket of a corresponding quadruple
modulator.
Conver s i on of i nterna l av si gnals t o asi o r lan
AV socket P1000 4 x Cinch AV
Feed of AV signals of the modules HDC 470 CI AV, HDC 480 CI AV, HDCT
460 AV, HDCT 461 AV into the modules HDE 164 or HDC 166.
• Connect AV socket P1000 to the AV socket of a corresponding QPSK or
COFDM to AV converter.
• Connect the module HDE 164 (ASI) or HDE 166 (LAN) via cinch cable to
the cinch sockets of the module.
- 8 - HAV 470
Combin ati on of e x t ernal a nd int e r nal s ignals
Cinch AV + AV socket P2000 AV socket P1000
– 1…3 cinch AV signals and 3…1 AV signals of socket P2000 can be output
at P1000.
– Video signals of socket P2000 combined with cinch audio signals can be
output at P1000.
• Connect the external audio and/or video signals via cinch cables to the
cinch sockets of the module.
• Connect AV socket P2000 to the AV socket of a corresponding QPSK or
COFDM to AV converter.
• Connect AV socket P1000 to the AV socket of a corresponding quadruple
modulator.
• Using the DIP switches the desired signals of P2000 can be switched to
P1000.
—> Connect only needed contacts. Avoid parallel connections of sourc-
es and sinks.
—> Therefore observe the signal assignment of the DIP switches (page 8).
A…D indicate the channel strips of the modules connected to
P1000/P2000.
- 9 - HAV 470
3.3 emC regulations
To comply with the current EMC regulations, it is necessary to connect the lines
leading in and out of the head-end station using cable terminals.
When mounting the module in a head-end station which is installed in a 19"
cabinet, make sure the connections leading in and out for the 19" cabinet are
made using cable terminals.
Tighten the nuts on the cable terminals until the teeth on the lock washer have penetrated the exterior coating and a good connection is made between the housing
and cable terminals.
- 10 - HAV 470
4 fi n a l p r o C e d u r e s
After installing the head-end station, upgrading accessories or installing mod-
ules it is necessary to tighten all cable connections, cable terminals and cover
screws in order to maintain compliance with current EMC regulations securely.
• Mount the base plate and the front cover (see STC 160 assembly instructions).
- 11 - HAV 470
Declaration of CE conformity
Service:
Phone: +49 (0) 911 / 703 2221 • Fax: +49 (0) 911 / 703 2326 • Email: service@gss.de
Grundig SAT Systems GmbH • Beuthener Straße 43 • D-90471 Nürnberg
Alterations reserved. Technical data E. & O.E. © by GSS GmbH 11022013
Loading...