GSN PATROL-701, Patrol 201 Pet Installation And User Manual
PATROL – 701
PASSIVE INFRARED
OPTOELECTRONIC
INTRUSION DETECTOR
FOR INDOOR USE
INSTALLATION
AND USER MANUAL
www.gsncompany.com
G.S.N. Electronic Company Ltd.
Special features.
Hi – tech design
Automatic pulse count
Detector’s sensitivity switch
regulator
Optoelectronic switch relay
Hi-light immunity –
no less then 10000 Lux
Hermetically insulated
pyrosensor
Low temperature mode
of working
Automatic temperature
compensation
High RFI & EMI immunity.
Description.
«PATROL-701» – passive infrared
detector with dual element
pyrosensor, was designed for
use in electronic alarm and
security systems
.
The device detects intrusion by
determining changes of energy
spectrum in infrared areas.
It emits no radiation and is harmless
for humans & animals.
The usage of “Fresnel Technologies”
original, optical, lightproof lens, has
allowed creating the detector, which
is protected from false alarms,
caused by a sunlight.
Selecting mounting location.
Choose a location where
the detector will have a best view
angle of the most possible intrusion
sight. For gain maximum protection
zone it is recommended to place a
detector on 2.1 meter height.
Attention!
Avoid the following locations:
Areas with rapid temperature
changes.
Areas with strong air flows
On unstable or vibrating
surfaces.
Detector performance improves,
if it's located in thermo stable and
dynamically constant environment.
Mounting the detector.
1. To remove the front cover,
push the lower part of the case,
with a flat screwdriver.
2. Loosen the screw that holds
the PCB and move it, down to
the keyhole. Remove the PCB
from the plastic case.
3. Detector can be placed vertically
or at a small angle (up to 10°).
- For vertical mount use the holes
on the front side of the back cover.
- Use a bracket for mounting the
detector at an angle.
4. For wires connection use
the specially signed holes on
the plastic case of the detector.
5. Mount the back cover of
the detector to the wall.
6. Place the PCB back in the cover
and fix the correct position with a
screw.
7. Connect the wires according to
the scheme.
+ 12V - TAMPER RELAY
8. For vertical mount place
the PCB in the "A" position.
9. For mounting on a bracket
place the PCB in the "B" position.
10. Close the detector’s cover
and fasten the screw.
Pulse count.
"PATROL-701" - Automatically
chooses and counts the levels
of the entering impulses,
according to the strength of the
signals acting on the detector.
Sensitivity switch regulator.
For premises with stable
temperature environment, without
warmth's & another's influences on
the detector, use the “HIGH' mode.
For premises with strong air flows,
temperature changes, vibrations
and est., use the “LOW” mode.
LOW
SENSITIVITY
HIGH
S2
Led indicator.
OFF
ON
JP 2
LED
OFF
ON
JP 2
LED
Jumper's "ON" position – LED is
activated and will light on in case
of intrusion.
Jumper's "OFF" position – LED is
turned off.
Mount the
detector under
angle 10
°
Place the PCB in "B" position if the
detector is mounted on the bracket.
B
A
PATROL 701
G.S.N. ELECTRONIC
COMPANY LTD.
+ 12V TAMPER RELAY
* AUTOMATIC
PULSES
OFF
ON
JP 2
LED
For bracket
installation
(angle 10 )
B
For straight
installation
A
LOW
SENSITIVITY
HIGH
S2
CS
Place the PCB in "A" position if the
detector is mounted on the vertical
position.
Wide angle lens
10m
(33ft)
5m
(16ft)
TOP VIEW
SIDE VIEW
5m
(16ft)
10m
(33ft)
0
2.1m
(6.8ft)
1.7m
(6ft)
3.7m
(12ft)
7m
(23ft)
15.6m
(51ft)
18m
(60ft)
90
o
Long range lens
14
21.5
77
5m
(16ft)
5m
(16ft)
2.5m
(8ft)
0
2.5m
(8ft)
2.1m
(6.8 ft)
1m
(
3ft
)3m(
10ft
)
2.2m
(
7ft
)
18.3m
(
60ft
)
10.7m
(
35ft
)
30.5m
(
100ft
)
29
6.5
TOP VIEW
SIDE VIEW
Curtain lens
5.6
2.1m
(6.8ft)
15m
(49ft)
7m
(23ft)
SIDE VIEW
TOP VIEW
0
18
44
Technical specification.
Detection
speed range:………0.3 to 3.0 m/sec
Power input:……………8.5 – 16Vdc
Current consumption:
In stand by mode:…………..11.5mA
In alarm mode
with LED on:…………………..10mA
In alarm mode
with LED off:…………………….7mA
Pulse mode
adjustable:…..….…………automatic
Alarm period:…………..………3 sec
Maximum detection range:……18 m
Relay output:..60V; 120mA; 16 Ohm
Warm up period:….………….40 sec
Reset time:………………...5 ± 1 sec
Light immunity:………………………
……………...no less then10000 Lux
Temperature range:…………………
………………from – 30°C to + 50°C
Storage temperature range:………..
………………from – 40°C to + 80°C
RFI immunity:………….….30 V/m in
range from 10 to 1000 MHz
EMI immunity:……………..50 000 V
Dimensions:93mm x 66mm x 46mm
Weight:…………………………85 gr.
PRINTED IN ISRAEL
Warranty.
G.S.N. Electronic Company Ltd. warrants this produc t to be free from
defects in materials and workmans hip under n orm al us e and ser vice f or a
period of five year from the last d ay of the week and year whose numbers
are printed on the printed circuit board inside this product.
GSN obligation is limited to repair ing or replacing this product, at its
option, free of charge for m aterials or labor, if it is pr oved to be def ective
in materials or workmanship under norm al use and service. GSN shall
have no obligation under this Limited Warrant y or otherwise if the product
is altered or improperly repaired or s erviced by anyone other the n GSN.
GSN shall not be liable for any malfunction that may be caused due to
improper installation. The customer should take all precaution necessary
to avoid and eliminate electro-static discharges and/or any other
disturbances that might interfere with its operation of the product.
There are no warranties, expressed or implied, of merchantability or
fitness for a particular purpose or oth erwise, which extend beyond the
description on the face hereof. In no case sha ll GSN be liable to anyone
for any consequential or incidental dam ages for breach of this or any
other warranty, expressed or implied, or upon any other basis of liabil ity
whatsoever, even if the loss or damage is caused by GSN own
negligence or fault.
GSN does not represent that this product can not be comprom ised o
r
circumvented; that this product will pre vent any person injur y or property
loss or damage by burglary, robbery, fire or other wise; or that th is produc t
will in all cases provide adequate warning or protection. Purchaser
understands that a properly installed and maintaine d product can only
reduce the risk of burglary, robbery or other events occurr ing without
providing an alarm, but it is not insurance or a guarantee that such will not
occur or that there will be no personal injury or proper ty loss or damage
as a result. Consequently, GSN shall have n o liability for any personal
injury, property damage or any other los s based on c la im that this product
failed to give any warning. However, if GSN is hel d l iable, whether directly
or indirectly, for any loss or damage aris ing under th is limited warranty or
otherwise, regardless of cause or origin, GSN m aximum liability sha ll not
in any case exceed the purchase price of this produc t, which shall be the
complete and exclusive remedy against.
Loading...