GS Instech CC L13, CC P18, CC I13, CC A18 User Manual

Clear Call

User Manual

Version 1.1

GSInstech Co., Ltd

Revision History

Version

Author

Descriptions

Date

Remarks

1.0

S.H Yoo

Draft

1 Aug 2018

1.1

S.H Yoo

FCC Label

6 Sep 2018

System Installation

Version

Change List

Remarks

Change List

GSInstech Co., Ltd

Abbreviations

Abbreviation

Term Definition

Remark

AGC

Automatic Gain Control

ALC

Automatic Level Control

BTS

Base Transceiver Station

Continuous Wave (un-modulated signal)

DFM

Digital Filter Module

Downlink The path covered from the BTS to the subscribers

service area via the repeater

Firmware

HPA

High Power Amplifier

Hardware

LNA

Low Noise Amplifier

LTE

Long Term Evolution

Mobile Station

PSU

Power Supply Unit

Radio Frequency

RFU

Radio Frequency Drive Unit

Software

Uplink The path covered from the subscribers service area to

the BTS via the repeater

VSWR

Voltage Standing Wave Ratio

GSInstech Co., Ltd

FCC ID(s)

HAAT (m)

Max. Antenna again

U88CC-L13

71656.75

6 dBi

U88CC-I13

26460.60

6 dBi

U88CC-P18

26143.43

6 dBi

U88CC-A18

72828.84

6 dBi

1. FCC Mandatory

1.1 FCC Warning States

1.1.1 FCC Part 15.21

Any changes or modifications not expressly approved by the party responsible for

compliance could void the user's authority to operate this equipment.

1.1.2 FCC Part 15.105

This equipment has been tested and found to comply with the limits for a Class A digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference when the equipment is operated in a

commercial environment. This equipment generates, uses, and can radiate radio frequency

energy and, if not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment in a residential

area is likely to cause harmful interference in which case the user will be required to correct

the interference at his own expense.

1.1.3 FCC Part 15.19

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

1.1.4 Antenna installation

. Antennas must be installed in accordance with FCC requirement.

The height of the antenna above average terrain (HAAT) must not exceed limit in the

following table.

1.1.5 Radiation Exposure Statement

GSInstech Co., Ltd

RF Radiation Exposure

This equipment complies with RF radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with a minimum distance of

WARNING

Provides information or instructions that the reader should follow in order to avoid

personal injury or fatality

CAUTION

Provides information or instructions that the reader should follow in order to avoid

a service failure or damage to the system

CHECK POINT

Provides the operator with checkpoint for stable system operation

NOTE

Indicates additional information as a reference

No use for the unauthorized device

When installing the system. Must check the devices that use is authorized.

This conditions apply antenna, cable, and if necessary

20 cm between the radiator and your body. This transmitter must not be co-located or

operating in conjunction with any other antenna or transmitter. RF exposure will be

addressed at time of installation and the use of higher gain antennas may require larger

separation distances.

1.1.6 FCC Warning Labels

1) FCC Part

1.2 Prohibitions

 Use of unauthorized antennas, cables, and coupling devices not conform to ERP/EIRP

and indoor‐only restrictions is prohibited.

 Preclude indications that home/personal use be prohibited.

1.3 Installation Warning statement

GSInstech Co., Ltd

Circuit Breaker Installation in the Box for Overcurrent Protection

Must install the circuit breaker between the system and main AC source for

separating.

Make sure to install the Circuit breaker on the place to operate easily Circuit breaker

be able to operate up to 20A

Terminal, Conduit and Cable size

To install the conduit is according to NAE regulation, and Terminal size is according

to NEC regulation

GSInstech Co., Ltd

Certification

Type

Remarks

FCC

Industrial RF Repeater

U88CC-L13

700MHz

U88CC-I13

800MHz

U88CC-P18

1900MHz

U88CC-A18

2100MHz

General Information

This document is primarily written for those who are new to Clear Call system and wish to

tune up the equipment. The document is applicable to below products from GSINSTECH.

Model number: Clear Call.

1.4 Repeater Information (FCC)

1.5 Purpose

Clear Call is a repeater, which has been designed to improve signals in blanket/shadow

areas inside of buildings to transmit Provider’s variety frequencies. User may choose filtering

configuration according to the specific site circumstances. It supports 700MHz LTE, 800MHz

iDEN, 850MHz Cellular, 1900MHz PCS and 2100MHz AWS frequency with one antenna

port. The max output is 18dBm and coverage is up to 25,000 SQFT.

1.6 Advantages

 It provides selectable RF power levels for any wireless technology/band  19inch rack or wall mount available depending on the installation site  Modular type for each frequency up to 4 modules  Can select service band through RSSI  Check and control the status of the repeater through front touch LCD  FPGA digital filtering provides optimized RF performance  Sub band filtering: It contains three non-contiguous high rejection digital filter  Quad band channel filtering, real time oscillation detect & gain control

GSInstech Co., Ltd

Description

Function

Remarks

Donor ANT Port

Antenna port for communication with BTS

4.3-10 DIN

Service ANT Port

Antenna port for communication with terminal/UE

4.3-10 DIN

Touch LCD

Display of status and select of function

2.2inch TFT LCD

Ethernet Port

GUI connection port for checking the status and control

RJ-45

Debug Port

Communication port for developer

Micro USB

Power Supply Port

Power supply port for each module

DC-005 jack

RF Unit

RF service unit

Max 4 unit

1.7 Appearance

GSInstech Co., Ltd

Item

Specification

Remark

700MHz

Down Link

728MHz ~ 757MHz

Band 12 & 13

Up Link

698MHz ~ 716MHz

Band 12

776MHz ~ 787MHz

Band 13

800MHz

Down Link

862MHz ~ 894MHz

Band 26

Up Link

817MHz ~ 849MHz

Band 26

1900MHz

Down Link

1930MHz ~ 1995MHz

Band 25

Up Link

1850MHz ~ 1915MHz

Band 25

2100MHz

Down Link

2110MHz ~ 2155MHz

Band 4

Up Link

1710MHz ~ 1755MHz

Band 4

Item

Specification

Remark

Band

700MHz

800MHz

1900MHz

2100MHz

Composite

Power

13dBm

18dBm

Gain

Range

75 ~ 45dB

80 ~ 50dB

Step

0.5dB

Accuracy

1dB

Roll-Off

-50dBc @ ±750kHz

Flatness

Single CH

≤ 4dB

Inter CH

≤ 5dB

UL Noise Figure

≤ 7dB

@ Max Gain

Group Delay

≤ 5us

Channel Select

Non-Contiguous 3Block

In/Out Port VSWR

2.0 : 1

Impedance

50Ω

Item

Specification

Remark

RF Connector

DIN (4.3-10) Type Female

AC-DC Adapter

Input : AC 90 ~ 264V, Output : DC 12V

DC Power Connector

DC-005

Size

Module

4.17 * 12.6 * 1.6inch

(106 * 321 * 40.9mm)

2. Specifications

2.1 Frequency Allocation

2.2 Common Specifications

2.3 Mechanical Spec.

GSInstech Co., Ltd

Chassis

17.2 * 18.1 * 1.75inch

(437 * 457.5 * 44.5mm)

Weight Module

< 2.98lbs (1.35Kg)

Chassis

< 19.84lbs (9Kg)

Included four modules

Operation Temperature

32 ~ 122°F (0 ~ 50°C)

Humidity

0 ~ 80%

2.4 Block Diagram

GSInstech Co., Ltd

+ 21 hidden pages

GS Instech CC L13, CC P18, CC I13, CC A18 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual