GS Instech B50KR User Manual

Download

B-50KR

User Guide

Building Cellular Signal Booster

Original

Version 1.0

2018, November

Changes

Version

Date

Technical Support : 913 469 6699

www.americanbst.com

This publication provides instructions for installing Cellular Signal Booster B-50KR.

Revision History

Certification

This equipment complies with the FCC directives.

INDEX

Product Introduction

Package Contents

Application Example 6

B-50KR Optional Components

Installation Guide 8

STEP 1. Find the Strongest Signal 8

STEP 2. Install the Outside Antenna

STEP 3. Run the Outside Antenna Cable 12

STEP 4. Install the Inside Antenna

STEP 5. Install the Signal Booster

LED Status & Troubleshooting

LED Bar Display

Functions

Specifications

Safety Guidelines 23

Warranty

Memo

B-50KR User Guide

B-50KR

merican Boost inside the buildings. B-50KR amplifies signals from the nearest base station and re-transmits them at higher power level. B-50KR provides service at 700MHz LTE, 850MHz Cellular, 1900MHz PCS and 2100MHz AWS frequencies without any additional setup or configuration.

-50KR has been designed to

improve

and extend c

ellular coverage

How it works

Receives Signal

The signal booster’s outside

antenna receives voice and data signals from a nearby

cell tower.

Receives Signal

The signal booster receives the signal from the outside antenna and after amplifying

the voice and data signals, sends

them to the inside antenna.

Improves Signal

The inside antenna

distributes the boosted

signals inside your building.

B-50KR User Guide

Package Contents

X8EA

B-50KR

User Guide

Building Cellular Signal Booster

Signal Booster B-50KR

Code No. : 0169

Inside Antenna Kit

Code No. : 83617

Outside Antenna Kit

Code No. : 83615

AC Power Cord

Code No. : 82W54

AC/DC Adaptor

Code No. : 833PU

Lightning Protector

Code No. : 834TJ

Side Bracket Kit

Code No. : 836K4

Coaxial Cable 100 ft.

Code No. : 834TL

Coaxial Cable 75 ft.

Code No. : 834TP

Coaxial Cable 2 ft.

Code No. : 834TK

User Guide

B-50KR User Guide

Application Example

Outside Antenna

Inside Antenna

B-50KR

B-50KR User Guide

B-50KR Optional Components

Outside Antenna

Inside Antenna

B-50KR

2 ft. Cable to lighting protector

100 ft. Cable to Ouside Antenna

75 ft. Cable to Inside Antenna

2 ft. Cable to Optional Splitter

Optional components enable signal amplification to a further area.

2 ft. cable to lighting protec tor

To Donor Port

Option Contents

Using multiple inside antennas for increased coverage.

Inside Antenna Kit

Code No. : 83617

Coaxial Cable 75 ft.

Code No. : 836WN

Optional Splitter

(2-Way)

Coaxial Cable 2 ft.

Code No. : 834TK

Optional Splitter

(3-Way)

Optional Splitter

(4-Way)

B-50KR User Guide

Installation Guide

STEP 1. Find the Strongest Signal

1-1. Using an iPhone

Dial *3001#12345#*, then press Call.

1-2. Using an Android

Download the ‘Network Signal info” from the Google Play store. After installing, you will be able to view your dB strength.

1-3. Using a Meter

If you have a meter that detects and displays the current signal levels, you can use it.

B-50KR User Guide

STEP 1. Find the Strongest Signal

Note The stronger signal you receive from the base station, the better coverage you will have

inside your building.

-70dBm

-90dBm

B-50KR User Guide

STEP 2. Install the Outside Antenna

The outside antenna must be mounted outside the building with the strongest cell signals. Mount the outside antenna as high as possible facing towards the desired location of the cell tower and facing the opposite direction of the expected location of the inside antenna.

Outside / Inside Antenna Separation

For the best performance, a minimum of 50 ft. distance between outside antenna and inside antenna is recommended. The bigger the separation distance from the antenna, the higher the coverage provided by the booster. However the smaller the separation distance, the lower the coverage provided by the booster.

B-50KR User Guide

STEP 2. Install the Outside Antenna

Install the outside antenna in the location to receive the strongest signal according to the instructions of STEP2. Make sure the outside antenna is installed facing towards the cell tower.

1 2

B-50KR User Guide

STEP 3. Run the Outside Antenna Cable

When mounting the outside antenna to the outside wall of your building, the easiest way is to run the cable on the outside of the wall and attach it to the exterior of your oflce & building.

Then drill a hole through the wall which will allow the cable to appear on the inside of the building. To avoid any potential harm or damage, make sure that there are no electrical outlets, sewer water pipes, or electrical wiring in the wall before drilling.

Note TV cables already being used for other purposes can not be shared with the cell

booster during installation.

After drilling the required hole, run the cable through and seal it. In some instances, it may be possible to run the cable up into the fascia of the attic overhang. In this circumstance, the cable will be accessible in the attic further routing.

Outside Antenna

to 2 ft. cable

To Lightning Protector

To Outside Antenna

Cable (100 ft.)

B-50KR User Guide

STEP 3. Run the Outside Antenna Cable

Outside Antenna Cable

B-50KR User Guide

STEP 4. Install the Inside Antenna

Choose a location for the inside antenna, more advantageously at the center of where the signal needs to be amplified.

2 3

B-50KR User Guide

STEP 4. Install the Inside Antenna

To Inside Antenna Cable (75 ft.)

Inside Antenna

Cable

Outside Antenna Cable

B-50KR User Guide

STEP 5. Install the Signal Booster

Choose a location for the signal booster, preferably away from excessive heat, direct sunlight, moisture and is free from high temperatures. Do not place the signal booster in an air-tight enclosure. Attic installations may expose the booster to high heat.

FH(+) M4 × 8

10-32 thread screw

B-50KR User Guide

STEP 5. Install the Signal Booster

From Outside Antenna

From Inside Antenna

Turn on the switch to ‘On’ after connecting the power source.

B-50KR User Guide

LED Status Description

Troubleshooting

Green indicates the Signal Booster is powered, and working properly.

No troubleshooting is required.

AC/DC adapter is damaged.

AC outlet does not provide power.

Verify that AC/DC adapter’s cable is not damaged.

Check if the AC outlet is working and not controlled by a wall switch that can cut power to the outlet.

Flashing Red

Isolation between the outside and inside antennas is being checked now. It will take up to 25 seconds.

No troubleshooting is required.

Status LED is green.

Input and output bars are green

Isolation between the outside and inside antennas is good and the Signal Booster is working properly.

No troubleshooting is required.

LED

LED Status & Troubleshooting

B-50KR User Guide

LED Status

Description

Troubleshooting

Status LED is red.

Output bars are flashing green.

Outside antenna and Inside antenna are not isolated enough from each other. So the Signal Booster is shutdown at this frequency.

Change the position of Outside and Inside antennas. Make sure the Outside antenna is not facing towards your own roof or at the inside antenna as this will cause isolation issue and the signal booster will stop amplifying signals at this frequency.

Flashing Red during 30 mins,

then Solid Red.

Uplink Signal coming from the outside antenna to Base Station is too strong and may cause troubles to carriers network, so the Signal Booster stops service at this frequency.

Signal from BTS station is too weak.

Change the position of Outside antenna to receive stronger signal from Base Station.

Outside antenna and Inside antenna is not isolated enough from each other.

The Signal Booster works properly.

B-50KR User Guide

LED Status

LED bars

Input Power

LED bars

Output Power

≤-81dBm

≤-16dBm

-80dBm ~ -71dBm

-15dBm ~ -6dBm

-70dBm ~ -61dBm

-5dBm ~ 4dBm

-60dBm ~ -51dBm

5dBm ~ 14dBm

≥ -50dBm/Total

≥ 15dBm/Total

LED Status

LED bars

Input Power

LED bars

Output Power

≤-86dBm

≤-16dBm

-85dBm ~ -76dBm

-15dBm ~ -6dBm

-75dBm ~ -66dBm

-5dBm ~ 4dBm

-65dBm ~ -56dBm

5dBm ~ 14dBm

≥ -55dBm/Total

≥ 15dBm/Total

LED

LED Bar Display

Number of LED bars on the front side of the Signal Booster will show input and output signal strength levels. The tables below indicate the signal strength levels.

Service band: 700MHz, 850MHz

Service band: 1900MHz, 2100MHz

B-50KR User Guide

Functions

ALC (Auto Level Control)

ALC maintains limit of the output power in order to protect bad influence to the Base Station.

AGC (Auto Gain Control)

The Signal Booster checks isolation between inside and outside antennas once a day. AGC sets up downlink and uplink gain value automatically depending on the input power level.

ASD (Auto Shutdown)

There are two cases when ASD works.

1) Outside antenna and Inside antenna are not isolated enough from each other. So in order to protect the Signal Booster from damage, it will automatically shutdown at this frequency.

2) Uplink Signal coming from the outside antenna to Base Station is too strong and may cause troubles to carriers network, so the Signal Booster will shutdown at this frequency.

LED Display

Number of LED bars on the front side of the Signal Booster will show input and output signal strength levels.

B-50KR User Guide

Parameter

Downlink

Uplink

Remark

700MHz LTE

734~756MHz 704~716MHz

Band 13 & 17

777~787MHz

Band 13

850MHz Cellullar

869~894MHz

824~849MHz

Band 5

1900MHz PCS

1930~1995MHz

1850~1915MHz

Band 25

2100MHz AWS

2110~2155MHz

Band 4

Composite Power

15dBm

20dBm

Maximum Gain

65dB (700 & 850) , 70dB (1900 & 2100)

Noise Figure

6dB nominal

EVM / Spurious Emission

3GPP & FCC Rule Complaint

ANT Isolation Setting

Gain + 15dB @ Initialization or Recheck

Impedance

50 Ohm

RF Connector

N-Type Female

Power Connector

DC-005 2ø

Power

7.5VDC x 5.4A

Size, inch

18.97 x 14 x 1U

W × H × D

Weight, lbs

9.04

Operation Temperature

14 ~ 122°F (-10°C ~ +50°C)

Humidity

0 ~ 80%

Material / Coating

AL / Flame Proof

Specifications

1710~1755MHz

B-50KR User Guide

Safety Guidelines

WARNING: This is NOT a CONSUMER

device. It is designed for installation by an installer approved by an

ISED

licensee.

You

MUST

have an

ISED LICENCE

or the express consent of an ISED licensee to operate this device.

WARNING

ELECTRIC SHOCK

Opening the Signal Booster could result in electric shock and may cause severe injury.

DAMAGE TO EQUIPMENT

Operating the Signal Booster with antennas in very close proximity facing each other could lead to a severe damage to the Signal Booster.

Use of unauthorized antennas, cables, and/or coupling devices not conforming with ERP/EIRP and/or indoor-only restrictions is prohibited.

Home/ personal use are prohibited.

CAUTION

THE SIGNAL BOOSTER SHOULD BE INSTALLED AS CLOSE AS POSSIBLE TO THE POWER SOURCE. THIS REPEATER IS FOR INDOOR USE ONLY AND SHOULD BE INSTALLED INSIDE OF THE VEHICLE.

FCC Warning Statements

FCC Part 15.105 statement

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

FCC Part 15.21 statement

Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment.

RF Exposure Statement

The antenna(s) must be installed such that a minimum separation distance of at least 20 cm is maintained between the radiator (antenna) and all persons at all times. This device must not be co-located or operating in conjunction with any other antenna or transmitter.

B-50KR User Guide

IC Warning Statements

RSS-GEN, Sec. 7.1.2 – (transmitters)

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

Conformément à la réglementation d’Industrie Canada, le présent émetteur radio peut fonctionneravec une antenne d’un type et d’un gain maximal (ou inférieur) approuvé pour l’émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l’intention desautres utilisateurs, il faut choisir le type d’antenne et son gain de sorte que la puissance isotroperayonnée quivalente (p.i.r.e.) ne dépassepas l’intensité nécessaire à l’établissement d’une communication satisfaisante.

RSS-GEN, Sec. 7.1.2 – (detachable antennas)

This radio transmitter (identify the device by certification number, or model number if Category II)has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device.

Le présent émetteur radio (identifier le dispositif par son numéro de certification ou son numéro de modèle s’il fait partie du matériel de catégorie I) a été approuvé par Industrie Canada pour fonctionner avec les types d’antenne énumérés ci-dessous et ayant un gain admissible maximal et l’impédance requise pour chaque type d’antenne. Les types d’antenne non inclus dans cette liste,ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l’exploitation de l’émetteur.

RF Radiation Exposure

This equipment complies with RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. RF exposure will be addressed at time of installation and the use of higher gain antennas require larger separation distances.

RSS-102 RF Exposure

L’antenne (ou les antennes) doit être installée de façon à maintenir à tout instant une distance minimum de au moins 20 cm entre la source de radiation (l’antenne) et toute personne physique. Cet appareil ne doit pas être installé ou utilisé en conjonction avec une autre antenne ou émetteur.

B-50KR User Guide

WARRANTY

Opening or tampering with the Signal Booster will void all warranties.

American Booster provides a 3-year warranty for B-50KR with all of its equipment.

Every product of American Booster is guaranteed to be free of material defects or component

malfunctions.

This warranty does not cover to any Signal Boosters that have been exposed to any misuse, abuse,

physical damage or inadequate maintenance.

Products returned by customers must be in their original, unmodified condition, shipped in the

original packaging with proof of purchase documentation enclosed, and a Return Merchandise

Authorization (RMA) number printed on the outside of the shipping box.

To repair or replace damaged Signal Boosters we may include refurbished American Booster’s products.

130 E Covey Run, Union, WA 98592

Technical Support : 913 469 6699

www.americanbst.com

B-50KR User Guide

Memo

B-50KR User Guide

Memo

www.americanbst.com

Technical Support : 913 469 6699

GS Instech B50KR User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual