PNEG-1831
60' Dura-Lok Plank and
Support Manual
Owner ’s Manual
PNEG-1831
Date: 01-08-13
All information, illustrations, photos, and specifications in this manual are based on the latest
information available at the time of publication. The right is reserved to make changes at any
time without notice.
2 PNEG-1831 60' Dura-Lok Plank and Support Manual
Table of Contents
Contents
Chapter 1 Introduction ..........................................................................................................................................4
Chapter 2 Safety .....................................................................................................................................................5
Safety Guidelines .................................................................................................................................. 5
General Safety Statement ..................................................................................................................... 6
Safety Instructions ..................... ... .... .......................................... ... ... ..................................................... 7
Safety Sign-Off Sheet ........................................................................................................................... 9
Proper Storage of Grain Bin/Silo Materials Prior to Construction ....................................................... 10
Chapter 3 Decals ..................................................................................................................................................11
Roof Damage Warning and Disclaimer ............................................................................................... 11
Chapter 4 Monorail Installation ..........................................................................................................................14
Fan Placement Diagram ..................................................................................................................... 14
Tie Bar Detail ......................................................... ... .... ... ... ... ............................................................. 15
Tie Strap Detail ......................................................... .... ... ... ... .... ... ... ... ... .... ... ... ... .... ... ... ...................... 16
Assembling Legs to Rail ...................................................................................................................... 17
Outer Perimeter Rail Details ............................................................................................................... 19
Splicing Rails ....................... .......................................... .......................................... ............................ 20
Chapter 5 Flooring - Planks ................................................................................................................................21
Floor Splice Details ... .......................................... ... ... .... .......................................... ... ... ...................... 21
Flashing Installation ............................................................................................................................ 22
Center Well Assembly Details ............................................................................................................. 24
Intermediate Well Assembly Details ....... ... ... .... ... ... ... .... ...................................................................... 25
Chapter 6 Layouts ................................................................................................................................................26
60'-15" Rail Spacing Layout ................................................................................................................ 26
60'-15" Monorail Spacing Layout ........................................................................................................ 27
60'-16" Monorail Spacing Layout ........................................................................................................ 28
60'-16" Rail Spacing Layout ................................................................................................................ 29
60'-17" Rail Spacing Layout ................................................................................................................ 30
60'-17" Monorail Spacing Layout ........................................................................................................ 31
60'-18" Monorail Spacing Layout ........................................................................................................ 32
60'-18" Rail Spacing Layout ................................................................................................................ 33
60'-20" Rail Spacing Layout ................................................................................................................ 34
60'-20" Monorail Spacing Layout ........................................................................................................ 35
60'-22" Monorail Spacing Layout ........................................................................................................ 36
60'-22" Rail Spacing Layout ................................................................................................................ 37
60'-26" Rail Spacing Layout ................................................................................................................ 38
60'-26" Monorail Spacing Layout ........................................................................................................ 39
60' Floor Bundle Layout ...................................................................................................................... 40
60' Plank Layout .................................................................................................................................. 43
Chapter 7 Warranty ..............................................................................................................................................45
PNEG-1831 60' Dura-Lok Plank and Support Manual 3
1. Introduction
READ THIS MANUAL carefully to learn how to properly use and install equipment. Failure to do so could
result in personal injury or equipment damage.
INSPECT the shipment immediately upon arrival. The customer is responsible for ensuring that all
quantities are correct. The customer should report and note any damage or shortage on the bill of
lading to justify their claim to the transport company.
THIS MANUAL SHOULD BE CONSIDERED a permanent part of your equipment and should be easily
accessible when needed.
This warranty provides you the assurance that the company will back its products when defects appear
within the warranty period. In some circumstances, the company also provides field improvements, often
without charge to the customer, even if the product is out of warranty. Should the equipment be abused,
or modified to change its performance beyond the factory specifications, the warranty will become void
and field improvements may be denied.
4 PNEG-1831 60' Dura-Lok Plank and Support Manual
2. Safety
DANGER
WARNING
CAUTION
NOTICE
This is the safety alert symbol. It is used to alert you
to potential personal injury hazards. Obey all safety
messages that follow this symbol to avoid possible
injury or death.
WARNING indicates a hazardous situation which, if not
avoided, could result in death or serious injury.
CAUTION, used with the safety alert symbol, indicates a
hazardous situation which, if not avoided, could result in
minor or moderate injury.
NOTICE is used to address practices not related to
personal injury.
DANGER indicates a hazardous situation which, if not
avoided, will result in death or serious injury.
Safety Guidelines
This manual contains information that is important for you, the owner/operator, to know and understand.
This information relates to protecting personal safety and preventing equipment problems. It is the
responsibility of the owner/operator to inform anyone operating or working in the area of this equipment
of these safety guidelines. To help you recognize this information, we use the symbols that are defined
below. Please read the manual and pay attention to these sections. Failure to read this manual and its
safety instructions is a misuse of the equipment and may lead to serious injury or death.
PNEG-1831 60' Dura-Lok Plank and Support Manual 5
2. Safety
This product has sharp edges, which may cause serious injury. To avoid injury, handle
sharp edges with caution and always use proper protective clothing and equipment.
General Safety Statement
Our foremost concern is your safety and the safety of others associated with grain handling equipment.
This manual is to help you understand safe operating procedures and some problems that may be
encountered by the operator and other personnel.
As owner and/or operator, you are responsible to know what requirements, hazards, and precau tions exist
and inform all personnel associated with the equipment or in the area. Safety precautions may be required
from the personnel. Avoid any alterations to the equipment, which may produce a very dangerous
situation, where SERIOUS INJURY or DEATH may occur.
You should consider the location of the bin site relative to power line locations or electrical transmission
equipment. Contact your local power company to review your installation plan or for information
concerning required equipment clearance. Clearance of portable equipment that may be taken to the bin
site should also be reviewed and considered. Any electrical control equipment in contact with the bin
should be properly grounded and installed in accordance with National Electric Code provisions and other
local or national codes.
This product is intended for the use of grain storage only. Any other use is a misuse of the product.
Sidewall bundles or sheets must be stored in a safe manner. The safest method of storing sidewall
bundles is laying horizontally with the arch of the sheet upward, like a dome. Sidewall sheets stored on
edge must be secured so that they cannot fall over and cause injury. Use care when handling and moving
sidewall bundles.
Personnel operating or working around equipment should read this manual. This manual must be
delivered with equipment to its owner. Failure to read this manual and its safety instructions is a
misuse of the equipment.
6 PNEG-1831 60' Dura-Lok Plank and Support Manual
2. Safety
Follow Safety Instructions
Carefully read all safety messages in this manual and
safety signs on your machine. Keep signs in good
condition. Replace missing or damaged safety signs. Be
sure new equipment components and repair parts include
the current safety signs. Replacement safety signs are
available from the manufacturer.
Learn how to operate the machine and how to use controls
properly. Do not let anyone operate without instruction.
Keep your machinery in proper working condition.
Unauthorized modifications to the machine may impair
the function and/or safety and affect machine life.
If you do not understand any part of this manual or need
assistance, contact your dealer.
Read and Understand Manual
Practice Safe Maintenance
Understand service procedures before doing work. Keep area
clean and dry.
Never lubricate, service, or adjust machine while it is in operation.
Keep hands, feet, and clothing away from rotating parts.
Keep all parts in good condition and properly installed. Fix
damage immediately . Replace worn or broken p arts. Remove any
built-up grease, oil, and debris.
Maintain Equipment
and Work Area
Safety Instructions
Our foremost concern is your safety and the safety of others associated with this equipment. We want to
keep you as a customer. This manual is to help you understand safe operating procedures and some
problems that may be encountered by the operator and other personnel.
As owner and/or operator, it is your responsibility to know what requirements, hazards, and precautions
exist, and to inform all personnel associated with the equipment or in the area. Safety precautions may be
required from the personnel. Avoid any alterations to the equipment. Such alterations may produce a very
dangerous situation where SERIOUS INJURY or DEATH may occur.
This equipment shall be installed in accordance with the current installation codes and applicable
regulations, which should be carefully followed in all cases. Authorities having jurisdiction should be
consulted before installations are made.
PNEG-1831 60' Dura-Lok Plank and Support Manual 7
2. Safety
Prepare for Emergencies
Be prepared if fire starts.
Keep a first aid kit and fire extinguisher handy.
Keep emergency numbers for doctors, ambulance service,
hospital, and fire department near your telephone.
Keep Emergency Equipment
Quickly Accessible
Wear Protective Clothing
Wear close-fitting clothing and safety equipment appropriate
to the job.
Remove all jewelry.
Tie long hair up and back.
Wear safety glasses at all times to protect eyes from debris.
Wear gloves to protect your hands from sharp edges on
plastic or steel parts.
Wear steel-toed boots to help protect your feet from falling
debris. Tuck in any loose or dangling shoestrings.
A respirator may be needed to prevent breathing potentially
toxic fumes and dust.
Wear a hard hat to help protect your head.
Wear appropriate fall protection equipment when working at
elevations greater than six feet (6').
Eye Protection
Gloves
Steel-Toed Boots
Respirator
Hard Hat
Fall Protection
8 PNEG-1831 60' Dura-Lok Plank and Support Manual
2. Safety
Safety Sign-Off Sheet
As a requirement of O.S.H.A., it is necessary for the employer to train the employee in the safe operating
and safety procedures for this equipment. This sign-off sheet is provided for your convenience and
personal record keeping. All unqualified persons are to stay out of the work area at all times. It is strongly
recommended that another qualified person who knows the shut down procedure be in the area in the
event of an emergency.
Date Employee Name Supervisor Name
PNEG-1831 60' Dura-Lok Plank and Support Manual 9
2. Safety
Proper Storage of Grain Bin/Silo Materials Prior to Construction
Wet storage stain (rust) will develop when closely packed bundles of galvanized material, such as sidewall
and roof sheets, have moisture present. Inspect roof and sidewall bundles on arrival for any moisture. If
moisture is present, it must not be allowed to remain between the she ets. Separate the sheets or panels
immediately and wipe them down. Spray with a light oil or diesel fuel.
If possible, sidewall bundles, roof sheets and other closely packed galvanized materials should be stored
in a dry, climate controlled building. If outdoor storage is unavoidable, the materials should be stored so
that they are raised above the ground and vegetation. Any stacking an d spacing mat erials sho uld not be
corrosive or wet. Be sure to protect materials from the weather, but permit air movement around the
bundles if possible.
Storing roof bundles and sidewall sheets at a slight incline can also help minimize the presence of
moisture. Storing the bundles with the center of the dome up (like an arch) is one option for minimizing
moisture during storage. Sidewall bundles can also be stored on edge but must be secured so that they
do not fall over and cause injury.
If “white rust” or “wet storage stain” occurs, contact the manufacturer imme diately about ways to minimize
the adverse effect upon the galvanized coating.
10 PNEG-1831 60' Dura-Lok Plank and Support Manual
Roof Damage Warning and Disclaimer
The manufacturer does not warrant any roof damage caused by excess ive v acuum or internal
pressure from fans or other air moving systems. Adequate ventilation and/or “makeup air”
devices should be provided for all powered air handling systems. The manufacturer does not
recommend the use of downward flow systems (suction). Severe roof damage can result from
any blockage of air passages. Running fans durin g high humidity/cold weather conditions can
cause air exhaust or intake ports to freeze.
CAUTION!
3. Decals
Excessive vacuum (or pressure) may
damage roof. Use positive aeration
system. Make sure all roof vents are
open and unobstructed. Start roof
fans when supply fans are started.
Do not operate when conditions exist
that may cause roof vent icing.
DC-969
PNEG-1831 60' Dura-Lok Plank and Support Manual 11
3. Decals
Rotating flighting will
kill or dismember.
Flowing material will
trap and suffocate.
Crusted material will
collapse and suffocate.
Keep clear of all augers.
DO NOT ENTER this bin!
Failure to heed these
warnings will result in
serious injury or death.
If you must enter the bin:
1. Shut off and lock out all power.
2. Use a safety harness and safety line.
3. Station another person outside the bin.
4. Avoid the center of the bin.
5. Wear proper breathing equipment or respirator.
DC-GBC-1A
ATTENTION: The decal shown below should be present on the outside of the door cover of the 2 ring,
24" porthole door cover and the roof manway cover. If a decal has been damaged or is missing in any of
these locations, contact the manufacturer for a free replacement decal.
GSI Decals
1004 E. Illinois St.
Assumption, IL. 62510
Phone: 1-217-226-4421
12 PNEG-1831 60' Dura-Lok Plank and Support Manual
3. Decals
ATTENTION: The decal shown below should be present on the outside of the door cover of the 2 ring,
24" porthole door cover and the roof manway cover. If a decal has been damaged or is missing in any of
these locations, contact the manufacturer for a free replacement decal.
GSI Decals
1004 E. Illinois St.
Assumption, IL. 62510
Phone: 1-217-226-4421
WARNING
DON’T
DO
UNLOADING INSTRUCTIONS:
1. Use CENTER FLOOR OUTLET ONLY until NO grain
remains above this outlet.
2. Side floor outlets to be used ONLY when above
condition is satisfied.
3. Lock all side floor outlets to avoid accidental
premature use.
4. See manufacturers instructions for proper use of
factory supplied sidedraw (wall) discharge systems.
Failure to heed these warnings
could result in serious injury, death,
structural damage or collapse of tank.
DC-GBC-2A
PNEG-1831 60' Dura-Lok Plank and Support Manual 13
4. Monorail Installation
Fan Placement Diagram
For uniform air flow, place the fans in relation to the unloading tube as shown in Figure 4A. Floor planks
should be perpendicular to the unloading tube.
Figure 4A
14 PNEG-1831 60' Dura-Lok Plank and Support Manual
4. Monorail Installation
Tie Bar Detail
1. Locate the tie bars between the rails. (Spaced evenly throughout the system.)
NOTE: Tie bars are to be placed at the end of monorail, at each splice and in the middle of the rail
if it is over 16' long. (Not necessarily evenly spaced.) Rail spacing details on Pages 26-38,
detail tie bar placements in each layout.
2. A single #10 x 5/8" self-drilling screws may be used to fasten the tie bars at each end to the rails
as necessary. (See Figure 4B.)
Figure 4B Tie Bar Detail
3. Tie bars should overlap and connect each rail to the next rail. Tie bars should be located along
each side of a rail splice and around the perimeter of the bin, no more than 6" from the end of the rail.
(See Figure 4C.)
Figure 4C Tie Bar Dimension Detail
PNEG-1831 60' Dura-Lok Plank and Support Manual 15
4. Monorail Installation
Tie Strap Detail
1. Tie straps should be used when a tie bar cannot be used to connect rails together due to special
spacing of monorail. Tie strap should be connected to all three (3) rails using self-drilling screws.
(See Figure 4D.)
2. Tie straps are to be located in the same places as a tie bar would be used.
NOTE: Some tie straps will be used to support center well and intermediate well assembly.
(See Figure 5F on Page 24 and Figure 5G on Page 25.)
Figure 4D Strap Detail
16 PNEG-1831 60' Dura-Lok Plank and Support Manual
4. Monorail Installation
See chart on Page 18.
Spacing depends on
eave height.
Assembling Legs to Rail
1. Place two (2) corners of the monorail leg into the rails as shown.
2. By twisting the leg it will spread the rail enough to get the other corners inside.
3. The leg can then be pushed down into the rail until the tabs lock it into place. (See Figure 4E.)
PNEG-1831 60' Dura-Lok Plank and Support Manual 17
Figure 4E Assembly Leg Rail
4. Monorail Installation
Monorail “Rail and Leg Spacing”/“Full Floor Leg Quantity” for 60' Bin Diameter
4.00"
Ring
3 4 11 26 See Page 38 23 891
46 16 26See Page 38 21 971
5 8 22 26 See Page 38 19 1068
710 27 22See Page 37 19 1210
9 12 33 22 See Page 37 18 1274
10 14 38 20 See Page 34 18 1393
11 16 43 20 See Page 34 17 1471
13 18 48 18 See Page 33 17 1601
14 20 54 18 See Page 33 17 1601
16 22 59 18 See Page 33 16 1697
17 24 64 17 See Page 30 16 1785
19 26 70 17 See Page 30 16 1785
20 28 75 16 See Page 29 16 1870
22 30 81 16 See Page 29 15 1989
2.66"
Ring
Eave Height (ft.) Rail Spacing
Reference
Page
Leg Spacing Leg Qty
23 32 86 16 See Page 29 15 1989
25 34 92 15 See Page 26 15 1984
27 37 100 15 See Page 26 15 1984
18 PNEG-1831 60' Dura-Lok Plank and Support Manual
4. Monorail Installation
Outer Perimeter Rail Details
3' Sections of monorail should be placed around the perimeter of the bin. Monorail legs for perimeter rails
should be spaced 16" apart on center. (See Figure 4F.)
Figure 4F
PNEG-1831 60' Dura-Lok Plank and Support Manual 19
4. Monorail Installation
Splicing Rails
1. A leg must be centered at each rail splice.
2. The closest leg may be moved a few inches over to center it under the splice. If more than 3" of
movement is required to center the leg under the splice, add an additional leg.
3. Fasten the rail to the leg with two (2) #10 self-drilling screws (splice locations o nly). (See Figure 4G.)
Figure 4G
20 PNEG-1831 60' Dura-Lok Plank and Support Manual
5. Flooring - Planks
Two (2) splices located at each splice location.
(See Figure 5B on Page 22.)
Floor Splice Details
Some of the floor planks will need to be spliced together. (See Figure 5F on Page 24 and plank layout
on Page 43 and plank length chart on Page 44.) Install plank length A first, then in stall the corresponding
plank length B. Continue until floor is complete. Center and install two (2) splices (PCL-7009) at each plank
splice location using self-drilling screws. Use eight (8) screws at the end of the splice for each plank,
four (4) on each side. (See Figure 5A below and Figure 5B on Page 22.)
Figure 5A Floor Splice Layout
PNEG-1831 60' Dura-Lok Plank and Support Manual 21
5. Flooring - Planks
Figure 5B Splice Assembly View
Flashing Installation
Figure 5C
Formed Flashing Installation
If bin sweep auger is to be used, overlap flashing such that rotation (usually clockwise) of the sweep will
climb up on the next flashing section. (See detail C in Figure 5C.) This will prevent the rotating/slipping
outer wheel of the sweep from catching on the flashing edges.
After the floor is in place, lay the flashing pieces on top of the floor place over the 1-1/4" bin bolts.
See Figure 5D and Figure 5E on Page 23 to determine the correct sequence for placing the nuts and
washers. Finger tighten the nuts. While holding flashing flat, fasten the flashing to the floor with sheet
metal screws. Now tighten flashing nuts.
22 PNEG-1831 60' Dura-Lok Plank and Support Manual
Flashing Installation (Continued)
Figure 5D 2.66" Corrugation
5. Flooring - Planks
Figure 5E 4.00" Corrugation
PNEG-1831 60' Dura-Lok Plank and Support Manual 23
5. Flooring - Planks
Center Well Assembly Details
Figure 5F 60' Diameter Bin Center Well Position
24 PNEG-1831 60' Dura-Lok Plank and Support Manual
Intermediate Well Assembly Details
5. Flooring - Planks
Figure 5G 60' Diameter Bin Intermediate Well Position
PNEG-1831 60' Dura-Lok Plank and Support Manual 25
6. Layouts
NOTE: This depicts monorail spacings only. Leg spacing is dependant
on eave height. See Page 18 for leg and rail spacing chart.
Tie bar (See Page 15 for
installation detail.)
60'-15" Rail Spacing Layout
Figure 6A 60' Diameter 15" Rail Spacing
26 PNEG-1831 60' Dura-Lok Plank and Support Manual
60'-15" Monorail Spacing Layout
Part # Description Qty
FL-404-15 15" Monorail Tie Bar 240
FL-7411 Monorail Strap 1-1/2" x 30" x 0.061" 60
S-280 #10-16 x 5/8" Zinc Self-Drilling Screw 940
NOTE: Fifty nine (59) total outer perimeter 3' monorail
pieces. See Page 17 for leg support details.
Bill of Materials
Part # Length Qty
A-22MONO 264 32
A-20.91MONO 251 4
A-19.5MONO 234 4
A-18.42MONO 221 4
A-18.33MONO 220 4
A-18.25MONO 219 4
A-18.08MONO 217 8
A-17.8MONO 214 4
A-17.66MONO 212 4
A-17.25MONO 207 4
A-16.8MONO 202 4
A-16.58MONO 199 2
A-16.4MONO 197 4
A-16.3MONO 196 4
A-15.83MONO 190 4
A-15.25MONO 183 4
A-14.58MONO 175 4
A-14.25MONO 171 4
A-13.91MONO 167 4
A-13MONO 156 4
A-12.1MONO 145 4
A-11.75MONO 141 4
A-11.08MONO 133 4
A-10.58MONO 127 2
A-3MONO 36 81
60' Diameter 15" Spacing
Measurement in Inches
Rail # Section 1 Section 2 Section 3
1 221 264 221
2 220 264 220
3 219 264 219
4 217 264 217
5 214 264 214
6 212 264 212
7 207 264 207
8 202 264 202
9 197 264 197
10 190 264 190
11 183 264 183
12 175 264 175
13 167 264 167
14 156 264 156
15 145 264 145
16 133 264 133
17 251 251
18 234 234
19 217 217
20 196 196
21 171 171
22 141 141
23 199
24 127
18.29 m Diameter 38.10 cm Spacing
Measurement in Centimeters
Rail # Section 1 Section 2 Section 3
1 561.34 670.56 561.34
2 558.8 670.56 558.8
3 556.26 670.56 556.26
4 551.18 670.56 551.18
5 543.56 670.56 543.56
6 538.48 670.56 538.48
7 525.78 670.56 525.78
8 513.08 670.56 513.08
9 500.38 670.56 500.38
10 482.6 670.56 482.6
11 464.82 670.56 464.82
12 444.5 670.56 444.5
13 424.18 670.56 424.18
14 396.24 670.56 396.24
15 368.3 670.56 368.3
16 337.82 670.56 337.82
17 637.54 637.54
18 594.36 594.36
19 551.18 551.18
20 497.84 497.84
21 434.34 434.34
22 358.14 358.14
23 505.46
24 322.58
PNEG-1831 60' Dura-Lok Plank and Support Manual 27
6. Layouts
Figure 6B 60' Diameter Bin with 15" Monorail Spacing
6. Layouts
Part # Description Qty
FL-404-16 16" Monorail Tie Bar 220
FL-7411 Monorail Strap 1-1/2" x 30" x 0.061" 80
S-280 #10-16 x 5/8" Zinc Self-Drilling Screw 890
Bill of Materials
Part # Length Qty
A-22MONO 264 32
A-20.83MONO 250 4
A-19.42MONO 233 4
A-18.42MONO 221 4
A-18.33MONO 220 4
A-18.25MONO 219 8
A-18MONO 216 4
A-17.75MONO 213 8
A-17.5MONO 210 4
A-17MONO 204 4
A-16.6MONO 200 4
A-16MONO 192 4
A-15.91MONO 191 4
A-15.5MONO 186 4
A-14.83MONO 178 4
A-14MONO 168 4
A-13.7MONO 164 6
A-13.1MONO 157 4
A-12.25MONO 147 4
A-11.08MONO 133 4
A-10.75MONO 129 4
A-3MONO 36 81
60' Diameter 16" Spacing
Measurement in Inches
Rail # Section 1 Section 2 Section 3
1 221 264 221
2220264220
* 3 219 264 219
4219264219
5 216 264 216
6213264213
7 210 264 210
8204264204
9 200 264 200
10 192 264 192
11 186 264 186
12 178 264 178
13 168 264 168
14 157 264 157
15 147 264 147
16 133 264 133
17 250 250
18 233 233
19 213 213
20 191 191
21 164 164
22 129 129
23 164
18.29 m Diameter 40.64 cm Spacing
Measurement in Centimeters
Rail # Section 1 Section 2 Section 3
1 561.34 670.56 561.34
2 558.8 670.56 558.8
* 3 556.26 670.56 556.26
4 556.26 670.56 556.26
5 548.64 670.56 548.64
6 541.02 670.56 541.02
7 533.4 670.56 533.4
8 518.16 670.56 518.16
9 508 670.56 508
10 487.68 670.56 487.68
11 472.44 670.56 472.44
12 452.12 670.56 452.12
13 426.72 670.56 426.72
14 398.78 670.56 398.78
15 373.38 670.56 373.38
16 337.82 670.56 337.82
17 635 635
18 591.82 591.82
19 541.02 541.02
20 485.14 485.14
21 416.56 416.56
22 327.66 327.66
23 416.56
NOTE: Fifty nine (59) total outer perimeter 3' monorail
pieces. See Page 17 for leg support details.
* NOTE: This special monorail run is used
to support the floor plank at the split.
60'-16" Monorail Spacing Layout
28 PNEG-1831 60' Dura-Lok Plank and Support Manual
Figure 6C 60' Diameter Bin with 16" Monorail Spacing
60'-16" Rail Spacing Layout
Tie bar (See Page 15 for
installation detail.)
Tie strap (See Page 16
for installation detail.)
NOTE: This depicts monorail spacings only. Leg spacing is dependant
on eave height. See Page 18 for leg and rail spacing chart.
6. Layouts
Figure 6D 60' Diameter 16" Rail Spacing
PNEG-1831 60' Dura-Lok Plank and Support Manual 29
6. Layouts
Tie strap (See Page 16
for installation detail.)
Tie bar (See Page 15 for
installation detail.)
NOTE: This depicts monorail spacings only. Leg spacing is dependant
on eave height. See Page 18 for leg and rail spacing chart.
60'-17" Rail Spacing Layout
Figure 6E 60' Diameter 17" Rail Spacing
30 PNEG-1831 60' Dura-Lok Plank and Support Manual
60'-17" Monorail Spacing Layout
Part # Description Qty
FL-404-17 17" Monorail Tie Bar 210
FL-7411 Monorail Strap 1-1/2" x 30" x 0.061" 80
S-280 #10-16 x 5/8" Zinc Self-Drilling Screw 880
Bill of Materials
Part # Length Qty
A-22MONO 264 30
A-21MONO 252 4
A-19.67MONO 236 2
A-19.5MONO 234 4
A-18.5MONO 222 4
A-18.33MONO 220 4
A-18.25MONO 219 8
A-18MONO 216 4
A-17.75MONO 213 8
A-17.3MONO 208 4
A-16.9MONO 203 4
A-16.4MONO 197 4
A-15.83MONO 190 4
A-15.75MONO 189 4
A-15.17MONO 182 4
A-14.4MONO 172 4
A-13.58MONO 163 2
A-13.42MONO 161 4
A-13.2MONO 158 4
A-12.42MONO 149 4
A-11.25MONO 135 4
A-3MONO 36 81
60' Diameter 17" Spacing
Measurement in Inches
Rail # Section 1 Section 2 Section 3
1 222 264 222
2 220 264 220
* 3 219 264 219
4 219 264 219
5 216 264 216
6 213 264 213
7 208 264 208
8 203 264 203
9 197 264 197
10 190 264 190
11 182 264 182
12 172 264 172
13 161 264 161
14 149 264 149
15 135 264 135
16 252 252
17 234 234
18 213 213
19 189 189
20 158 158
21 236
22 163
18.29 m Diameter 43.18 cm Spacing
Measurement in Centimeters
Rail # Section 1 Section 2 Section 3
1 563.88 670.56 563.88
2 558.8 670.56 558.8
* 3 556.26 670.56 556.26
4 556.26 670.56 556.26
5 548.64 670.56 548.64
6 541.02 670.56 541.02
7 528.32 670.56 528.32
8 515.62 670.56 515.62
9 500.38 670.56 500.38
10 482.6 670.56 482.6
11 462.28 670.56 462.28
12 436.88 670.56 436.88
13 408.94 670.56 408.94
14 378.46 670.56 378.46
15 342.9 670.56 342.9
16 640.08 640.08
17 594.36 594.36
18 541.02 541.02
19 480.06 480.06
20 401.32 401.32
21 599.44
22 414.02
NOTE: Fifty nine (59) total outer perimeter 3' monorail
pieces. See Page 17 for leg support details.
* NOTE: This special monorail run is used
to support the floor plank at the split.
6. Layouts
PNEG-1831 60' Dura-Lok Plank and Support Manual 31
Figure 6F 60' Diameter Bin with 17" Monorail Spacing
6. Layouts
Part # Description Qty
FL-404-18 18" Monorail Tie Bar 200
FL-7411 Monorail Strap 1-1/2" x 30" x 0.061" 80
S-280 #10-16 x 5/8" Zinc Self-Drilling Screw 830
Bill of Materials
Part # Length Qty
A-22MONO 264 28
A-21.33MONO 256 4
A-19.75MONO 237 4
A-19MONO 228 2
A-18.42MONO 221 4
A-18.33MONO 220 4
A-18.25MONO 219 8
A-17.9MONO 215 8
A-17.66MONO 212 4
A-17.25MONO 207 4
A-16.75MONO 201 4
A-16.2MONO 194 4
A-15.83MONO 190 4
A-15.5MONO 186 4
A-14.67MONO 176 4
A-13.9MONO 166 4
A-13.2MONO 158 4
A-12.8MONO 153 4
A-12.3MONO 148 2
A-11.58MONO 139 4
A-3MONO 36 81
60' Diameter 18" Spacing
Measurement in Inches
Rail # Section 1 Section 2 Section 3
1 221 264 221
2 220 264 220
* 3 219 264 219
4 219 264 219
5 215 264 215
6 212 264 212
7 207 264 207
8 201 264 201
9 194 264 194
10 186 264 186
11 176 264 176
12 166 264 166
13 153 264 153
14 139 264 139
15 256 256
16 237 237
17 215 215
18 190 190
19 158 158
20 228
21 148
18.29 m Diameter 40.64 cm Spacing
Measurement in Centimeters
Rail # Section 1 Section 2 Section 3
1 561.34 670.56 561.34
2 558.8 670.56 558.8
* 3 556.26 670.56 556.26
4 556.26 670.56 556.26
5 546.1 670.56 546.1
6 538.48 670.56 538.48
7 525.78 670.56 525.78
8 510.54 670.56 510.54
9 492.76 670.56 492.76
10 472.44 670.56 472.44
11 447.04 670.56 447.04
12 421.64 670.56 421.64
13 388.62 670.56 388.62
14 353.06 670.56 353.06
15 650.24 650.24
16 601.98 601.98
17 546.1 546.1
18 482.6 482.6
19 401.32 401.32
20 579.12
21 375.92
NOTE: Fifty nine (59) total outer perimeter 3' monorail
pieces. See Page 17 for leg support details.
* NOTE: This special monorail run is used
to support the floor plank at the split.
60'-18" Monorail Spacing Layout
32 PNEG-1831 60' Dura-Lok Plank and Support Manual
Figure 6G 60' Diameter Bin with 18" Monorail Spacing
60'-18" Rail Spacing Layout
Tie strap (See Page 16
for installation detail.)
Tie bar (See Page 15 for
installation detail.)
NOTE: This depicts monorail spacings only. Leg spacing is dependant
on eave height. See Page 18 for leg and rail spacing chart.
6. Layouts
Figure 6H 60' Diameter 18" Rail Spacing
PNEG-1831 60' Dura-Lok Plank and Support Manual 33
6. Layouts
Tie strap (See Page 16
for installation detail.)
Tie bar (See Page 15 for
installation detail.)
NOTE: This depicts monorail spacings only. Leg spacing is dependant
on eave height. See Page 18 for leg and rail spacing chart.
60'-20" Rail Spacing Layout
Figure 6I 60' Diameter 20" Rail Spacing
34 PNEG-1831 60' Dura-Lok Plank and Support Manual
60'-20" Monorail Spacing Layout
Bill of Materials
Part # Length Qty
A-22MONO 264 26
A-20.67MONO 248 4
A-20.42MONO 245 2
A-18.92MONO 227 4
A-18.42MONO 221 4
A-18.33MONO 220 4
A-18.25MONO 219 4
A-18.2MONO 218 4
A-17.8MONO 214 4
A-17.42MONO 209 4
A-16.9MONO 203 4
A-16.6MONO 200 4
A-16.3MONO 196 4
A-15.58MONO 187 4
A-14.75MONO 177 4
A-13.91MONO 167 4
A-13.75MONO 165 4
A-13.3MONO 160 2
A-12.58MONO 151 4
A-11.25MONO 135 4
A-3MONO 36 81
60' Diameter 20" Spacing
Measurement in Inches
Rail # Section 1 Section 2 Section 3
1 221 264 221
* 2 220 264
220
3 219 264 219
4 218 264 218
5 214 264 214
6 209 264 209
7 203 264 203
8 196 264 196
9 187 264 187
10 177 264 177
11 165 264 165
12 151 264 151
13 135 264 135
14 248 248
15 227 227
16 200 200
17 167 167
18 245
19 160
Part # Description Qty
FL-404-20 20" Monorail Tie Bar 170
FL-7411 Monorail Strap 1-1/2" x 30" x 0.061" 80
S-280 #10-16 x 5/8" Zinc Self-Drilling Screw 770
NOTE: Fifty nine (59) total outer perimeter 3' monorail
pieces. See Page 17 for leg support details.
* NOTE: This special monorail run is used
to support the floor plank at the split.
18.29 m Diameter 50.8 Spacing
Measurement in Centimeters
Rail # Section 1 Section 2 Section 3
1 561.34 670.56 561.34
* 2 558.8 670.56
558.8
3 556.26 670.56 556.26
4 553.72 670.56 553.72
5 543.56 670.56 543.56
6 530.86 670.56 530.86
7 515.62 670.56 515.62
8 497.84 670.56 497.84
9 474.98 670.56 474.98
10 449.58 670.56 449.58
11 419.1 670.56 419.1
12 383.54 670.56 383.54
13 342.9 670.56 342.9
14 629.92 629.92
15 576.58 576.58
16 508 508
17 424.18 424.18
18 622.3
19 406.4
6. Layouts
PNEG-1831 60' Dura-Lok Plank and Support Manual 35
Figure 6J 60' Diameter Bin with 20" Monorail Spacing
6. Layouts
60' Diameter 22" Spacing
Measurement in Inches
Rail # Section 1 Section 2 Section 3
1 221 264 221
* 2 219 264
219
3 219 264 219
4 217 264 217
5 212 264 212
6 207 264 207
7 200 264 200
8 190 264 190
9 179 264 179
10 167 264 167
11 152 264 152
12 134 264 134
13 245 245
14 221 221
15 189 189
16 148 148
17 203
Bill of Materials
Part # Length Qty
A-22MONO 264 24
A-20.42MONO 245 4
A-18.42MONO 221 8
A-18.25MONO 219 8
A-18.08MONO 217 4
A-17.66MONO 212 4
A-17.25MONO 207 4
A-16.9MONO 203 2
A-16.6MONO 200 4
A-15.83MONO 190 4
A-15.75MONO 189 4
A-14.9MONO 179 4
A-13.91MONO 167 4
A-12.7MONO 152 4
A-12.3MONO 148 4
A-11.17MONO 134 4
A-3MONO 36 81
Part # Description Qty
FL-404-22 22" Monorail Tie Bar 150
FL-7411 Monorail Strap 1-1/2" x 30" x 0.061" 80
S-280 #10-16 x 5/8" Zinc Self-Drilling Screw 720
NOTE: Fifty nine (59) total outer perimeter 3' monorail
pieces. See Page 17 for leg support details.
* NOTE: This special monorail run is used
to support the floor plank at the split.
18.29 m Diameter 55.88 cm Spacing
Measurement in Centimeters
Rail # Section 1 Section 2 Section 3
1 561.34 670.56 561.34
* 2 556.26 670.56
556.26
3 556.26 670.56 556.26
4 551.18 670.56 551.18
5 538.48 670.56 538.48
6 525.78 670.56 525.78
7 508 670.56 508
8 482.6 670.56 482.6
9 454.66 670.56 454.66
10 424.18 670.56 424.18
11 386.08 670.56 386.08
12 340.36 670.56 340.36
13 622.3 622.3
14 561.34 561.34
15 480.06 480.06
16 375.92 375.92
17 515.62
60'-22" Monorail Spacing Layout
36 PNEG-1831 60' Dura-Lok Plank and Support Manual
Figure 6K 60' Diameter Bin with 22" Monorail Spacing
60'-22" Rail Spacing Layout
Tie strap (See Page 16
for installation details.)
Tie bar (See Page 15 for
installation details.)
NOTE: This depicts monorail spacings only. Leg spacing is dependant
on eave height. See Page 18 for leg and rail spacing chart.
6. Layouts
Figure 6L 60' Diameter 22" Rail Spacing
PNEG-1831 60' Dura-Lok Plank and Support Manual 37
6. Layouts
Tie strap (See Page 16
for installation details.)
Tie bar (See Page 15 for
installation details.)
NOTE: This depicts monorail spacings only. Leg spacing is dependant
on eave height. See Page 18 for leg and rail spacing chart.
60'-26" Rail Spacing Layout
Figure 6M 60' Diameter 26" Rail Spacing
38 PNEG-1831 60' Dura-Lok Plank and Support Manual
60'-26" Monorail Spacing Layout
Bill of Materials
Part # Length Qty
A-22MONO 264 20
A-20.91MONO 251 4
A-18.63MONO 223 4
A-18.42MONO 221 4
A-18.25MONO 219 8
A-17.9MONO 215 4
A-17.42MONO 209 4
A-16.75MONO 201 4
A-15.83MONO 190 4
A-15.5MONO 186 4
A-15.25MONO 183 2
A-14.75MONO 177 4
A-13.42MONO 161 4
A-11.83MONO 142 4
A-11.25MONO 135 4
A-3MONO 36 81
60' Diameter 26" Spacing
Measurement in Inches
Rail # Section 1 Section 2 Section 3
1 221 264 221
* 2 219 264
219
3 219 264 219
4 215 264 215
5 209 264 209
6 201 264 201
7 190 264 190
8 177 264 177
9 161 264 161
10 142 264 142
11 251 251
12 223 223
13 186 186
14 135 135
15 183
18.29 m Diameter 66.04 cm Spacing
Measurement in Centimeters
Rail # Section 1 Section 2 Section 3
1 561.34 670.56 561.34
* 2 556.26 670.56
556.26
3 556.26 670.56 556.26
4 546.1 670.56 546.1
5 530.86 670.56 530.86
6 510.54 670.56 510.54
7 482.6 670.56 482.6
8 449.58 670.56 449.58
9 408.94 670.56 408.94
10 360.68 670.56 360.68
11 637.54 637.54
12 566.42 566.42
13 472.44 472.44
14 342.9 342.9
15 464.82
Part # Description Qty
FL-404-26 26" Monorail Tie Bar 130
FL-7411 Monorail Strap 1-1/2" x 30" x 0.061" 80
S-280 #10-16 x 5/8" Zinc Self-Drilling Screw 630
NOTE: Fifty nine (59) total outer perimeter 3' monorail
pieces. See Page 17 for leg support details.
* NOTE: This special monorail run is used
to support the floor plank at the split.
6. Layouts
PNEG-1831 60' Dura-Lok Plank and Support Manual 39
Figure 6N 60' Diameter Bin with 26" Monorail Spacing
6. Layouts
NOTE: The 60' floor is split up into two (2) identical bundles. Each bundle covers half of the floor. The split of the floor
is staggered from one 7" plank to the next. The bundle is arranged so that the “A” plank is installed together with the
“B” plank. Begin installation with plank 1 found in bundle.
60' Floor Bundle Layout
29'-2"
Critical starting
dimension for
first plank
Bundle 1
Bundle 2
Figure 6O 60' Plank Layout Bundles
40 PNEG-1831 60' Dura-Lok Plank and Support Manual
6. Layouts
60' Dura-Lok Plank Floor Bundle Layout
Plank Layout by Marking Plank Layout by Length
2B 1 2A 137 147 65
9B 7B 5B 3B 166 146 119-1/2 86-1/2
10A 8A 6A 4A 176 155 133-1/2 104
9A 7A 5A 3A
10B 8B 6B 4B 248 227 205-1/2 176
17B 15B 13B 11B 230 216 202 185
18A 16A 14A 12A 236 223 209 191
17A 15A 13A 11A
18B 16B 14B 12B 308 295 281 263
25B 23B 21B 19B 270 262 252 241
26A 24A 22A 20A 275 266 257 247
25A 23A 21A 19A
26B 24B 22B 20B 347 338 329 319
33B 31B 29B 27B 298 292 286 279
34A 32A 30A 28A 300 295 289 282
33A 31A 29A 27A
34B 32B 30B 28B 372 367 361 354
41B 39B 37B 35B 313 310 307 303
42A 40A 38A 36A 314 312 309 305
238 218 191-1/2 158-1/2
302 288 274 257
342 334 324 313
370 364 358 351
41A 39A 37A 35A
42B 40B 38B 36B 386 384 381 377
49B 47B 45B 43B 319 318 317 315
50A 48A 46A 44A 319 319 317-1/2 316
49A 47A 45A 43A
50B 48B 46B 44B 391 391 389-1/2 388
385 382 379 375
391 390 389 387
NOTES:
1. Looking from end of the bundle where all plank edges are butted flush.
2. Two (2) identical bundles required for complete floor.
3. Plank banding and sub-banding denoted by grid lines in charts.
PNEG-1831 60' Dura-Lok Plank and Support Manual 41
NOTES
42 PNEG-1831 60' Dura-Lok Plank and Support Manual
60' Plank Layout
6. Layouts
Figure 6P Plank Layout for 60' Diameter Bin
PNEG-1831 60' Dura-Lok Plank and Support Manual 43
6. Layouts
60' Plank Layout for Manual
Plank # Length In Inch In Metric Plank # Length In Inch In Metric
1 12'-3" 147 373.38
2A 5'-5" 65 165.1 2B 11'-5" 137 347.98
3A 13' - 2-1/2" 158-1/2 402.59 3B 7' - 2-1/2" 86-1/2 219.71
4A 8'-8" 104 264.16
5A 15' - 11-1/2" 191-1/2 486.41 5B 9' - 11-1/2" 119-1/2 303.53
6A 11' - 1-1/2" 133-1/2 339.09
7A 18'-2" 218 553.72 7B 12'-2" 146 370.84
8A 12'-11" 155 393.7
9A 19'-10" 238 604.52 9B 13'-10" 166 421.64
10A 14'-8" 176 447.04
11A 21'-5" 257 652.78 11B 15'-5" 185 469.9
12A 15'-11" 191 485.14
13A 22'-10" 274 695.96 13B 16'-10" 202 513.08
14A 17'-5" 209 530.86
15A 24'-0" 288 731.52 15B 18'-0" 216 548.64
16A 18'-7" 223 566.42
17A 25'-2" 302 767.08 17B 19'-2" 230 584.2
18A 19'-8" 236 599.44 18B 25'-8" 308 782.32
19A 26'-1" 313 795.02 19B 20'-1" 241 612.14
20A 20'-7" 247 627.38
21A 27'-0" 324 822.96 21B 21'-0" 252 640.08
22A 21'-5" 257 652.78
23A 27'-10" 334 848.36 23B 21'-10" 262 665.48
24A 22'-2" 266 675.64 24B 28'-2" 338 858.52
25A 28'-6" 342 868.68 25B 22'-6" 270 685.8
26A 22'-11" 275 698.5
27A 29'-3" 351 891.54 27B 23'-3" 279 708.66
28A 23'-6" 282 716.28
29A 29'-10" 358 909.32 29B 23'-10" 286 726.44
30A 24'-1" 289 734.06 30B 30'-1" 361 916.94
31A 30'-4" 364 924.56 31B 24'-4" 292 741.68
32A 24'-7" 295 749.3
33A 30'-10" 370 939.8 33B 24'-10" 298 756.92
34A 25'-0" 300 762
35A 31'-3" 375 952.5 35B 25'-3" 303 769.62
36A 25'-5" 305 774.7 36B 31'-5" 377 957.58
37A 31'-7" 379 962.66 37B 25'-7" 307 779.78
38A 25'-9" 309 784.86
39A 31'-10" 382 970.28 39B 25'-10" 310 787.4
40A 26'-0" 312 792.48
41A 32'-1" 385 977.9 41B 26'-1" 313 795.02
42A 26'-2" 314 797.56
43A 32'-3" 387 982.98 43B 26'-3" 315 800.1
44A 26'-4" 316 802.64
45A 32'-5" 389 988.06 45B 26'-5" 317 805.18
46A 26' - 5-1/2" 317-1/2 806.45
47A 32'-6" 390 990.6 47B 26'-6" 318 807.72
48A 26'-7" 319 810.26
49A 32'-7" 391 993.14 49B 26'-7" 319 810.26
50A 26'-7" 319 810.26
4B 14'-8" 176 447.04
6B 17' - 1-1/2" 205-1/2 521.97
8B 18'-11" 227 576.58
10B 20'-8" 248 629.92
12B 21'-11" 263 668.02
14B 23'-5" 281 713.74
16B 24'-7" 295 749.3
20B 26'-7" 319 810.26
22B 27'-5" 329 835.66
26B 28'-11" 347 881.38
28B 29'-6" 354 899.16
32B 30'-7" 367 932.18
34B 31'-0" 372 944.88
38B 31'-9" 381 967.74
40B 32'-0" 384 975.36
42B 32'-2" 386 980.44
44B 32'-4" 388 985.52
46B 32' - 5-1/2" 389-1/2 989.33
48B 32'-7" 391 993.14
50B 32'-7" 391 993.14
44 PNEG-1831 60' Dura-Lok Plank and Support Manual
7. Warranty
9101239_1_CR_rev7.DOC (revised July 2009)
GSI Group, LLC Limited Warranty
The GSI Group, LLC (“GSI”) warrants products which it manufactures to be free of defects in materials and workmanship
under normal usage and conditions for a period of 12 months after sale to the original end-user or if a foreign sale,
14 months from arrival at port of discharge, whichever is earlier. The end-user’s sole remedy (and GSI’s only obligation)
is to repair or replace, at GSI’s option and expense, products that in GSI’s judgment, contain a material defect in materials
or workmanship. Expenses incurred by or on behalf of the end-user without prior written authorization from the GSI
Warranty Group shall be the sole responsibility of the end-user.
Warranty Extensions:
The Limited Warranty period is extended for the following products:
Product Warranty Period
Performer Series Direct Drive Fan Motor 3 Years
AP Fans and Flooring
Cumberland
Feeding/Watering
Systems
Grain Systems Grain Bin Structural Design 5 Years
Grain Systems
Farm Fans
Zimmerman
All Fiberglass Housings Lifetime
All Fiberglass Propellers Lifetime
Feeder System Pan Assemblies 5 Years **
Feed Tubes (1-3/4" and 2.00") 10 Years *
Centerless Augers 10 Years *
Watering Nipples 10 Years *
Portable and Tower Dryers 2 Years
Portable and Tower Dryer Frames and
Internal Infrastructure †
5 Years
* Warranty prorated from list price:
0 to 3 years - no cost to end-user
3 to 5 years - end-user pays 25%
5 to 7 years - end-user pays 50%
7 to 10 years - end-user pays 75%
** Warranty prorated from list price:
0 to 3 years - no cost to end-user
3 to 5 years - end-user pays 50%
† Motors, burner components
and moving parts not included.
Portable dryer screens included.
Tower dryer screens not included.
GSI further warrants that the portable and tower dryer frame and basket, excluding all auger and auger drive components,
shall be free from defects in materials for a period of time beginning on the twelfth (12
and continuing until the sixtieth (60
th
) month from the date of purchase (extended warranty period). During the extended
th
) month from the date of purchase
warranty period, GSI will replace the frame or basket components that prove to be defective under normal conditions
of use without charge, excluding the labor, transportation, and/or shipping costs incurred in the performance of this
extended warranty.
Conditions and Limitations:
THERE ARE NO WARRANTIES THAT EXTEND BEYOND THE LIMITED WARRANTY DESCRIPTION SET FORTH
ABOVE. SPECIFICALLY, GSI MAKES NO FURTHER WARRANTY OF ANY KIND, EXPRESS OR IMPLIED,
INCLUDING, WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR
PURPOSE OR USE IN CONNECTION WITH: (I) PRODUCT MANUFACTURED OR SOLD BY GSI OR (II) ANY ADVICE,
INSTRUCTION, RECOMMENDATION OR SUGGESTION PROVIDED BY AN AGENT, REPRESENTATIVE OR
EMPLOYEE OF GSI REGARDING OR RELATED TO THE CONFIGURATION, INSTALLATION, LAYOUT, SUITABILITY
FOR A PARTICULAR PURPOSE, OR DESIGN OF SUCH PRODUCTS.
GSI shall not be liable for any direct, indirect, incidental or consequential damages, including, without limitation, loss of
anticipated profits or benefits. The sole and exclusive remedy is set forth in the Limited Warranty, which shall not exceed
the amount paid for the product purchased. This warranty is not transferable and applies only to the original end-user. GSI
shall have no obligation or responsibility for any representations or warranties made by or on behalf of any dealer, agent
or distributor.
GSI assumes no responsibility for claims resulting from construction defects or unauthorized modifications to products
which it manufactured. Modifications to products not specifically delineated in the manual accompanying the equipment at
initial sale will void the Limited Warranty.
This Limited Warranty shall not extend to products or parts which have been damaged by negligent use, misuse, alteration,
accident or which have been improperly/inadequately maintained. This Limited Warranty extends solely to products
manufactured by GSI.
Prior to installation, the end-user has the responsibility to comply with federal, state and local codes which apply to the
location and installation of products manufactured or sold by GSI.
PNEG-1831 60' Dura-Lok Plank and Support Manual 45
This equipment shall be installed in accordance with
the current installation codes and applicable
regulations, which should be carefully followed in
all cases. Authorities having jurisdiction should be
consulted before installations are made.
Copyright © 2013 by GSI Group
Printed in the USA
GSI Group
1004 E. Illinois St.
Assumption, IL 62510-0020
Phone: 1-217-226-4421
Fax: 1-217-226-4420
www.gsiag.com
CN-303328
Loading...