MA0310-EA
Operation Guide 2689
Power Saving
The Power Saving feature of the watch is turned on at the factory.
• Power Saving causes the watch to automatically enter a sleep state to save power whenever the watch is left in the dark.
• Note that the watch may also enter the sleep state if the watch is blocked from light by your sleeve.
❚
How the sleep state works
• Display sleep state
The display sleep state is triggered whenever the watch is left in
the dark for about one hour between the hours of 10 p.m. and
6 a.m.
• The display goes blank, except for a sleep indicator flashing on
it.
Alarms and the hourly time signal continue to operate normally
while the watch is in the display sleep state.
• The watch does not enter the sleep state if it is in the
Stopwatch Mode.
• Function sleep state
The function sleep state is triggered whenever the watch is left in the
dark for six or seven days.
• The sleep mark stops flashing and remains on the display.
Alarms, the hourly time signal, and auto signal reception are
also disabled while the watch is in the function sleep state.
Sleep indicator
Modes and Display Screens
Timekeeping Mode
Days of the Week
SUN : Sunday MON : Monday TUE : Tuesday
WED : Wednesday THU : Thursday FRI : Friday
SAT : Saturday
• Digital timekeeping functions continue to operate normally in
the function sleep state.
❚
To recover from the sleep state
Place the watch in an area that is well-lit, press any button, or
angle the watch toward your face to illuminate the display using
the Auto Light.
• It can take up to two seconds before the display re-appears after
you place the watch in a well-lit area.
❚
To turn power saving on or off
Use the procedure under “Setting the Time and Date Manually” to
turn Power Saving on or off.
Leaving the watch in a drawer or anywhere else it is dark can
cause Power Saving to trigger in order to conserve battery
power.
Segments indicate the passage
of 5-minute intervals.
• The watch will automatically revert to the Timekeeping Mode if you leave it in the Alarm Mode or Recall Mode without performing
any operation for about two or three minutes.
• Entering the Alarm Mode displays an alarm number, “SNZ” (snooze alarm), or “SIG” (hourly time signal).
World Time Mode Recall Mode
Time Stamp (Time Memo)
Holding down the B button for about one second in
the Timekeeping Mode creates a record containing
the current date (month and day) and time (hour,
minute, second) in memory. Storage of the record is
indicated by the watch beeping.
• The display shows the contents of the record for about
two seconds, after which the normal Timekeeping Mode
display reappears.
• See for information about recalling Time Stamp records.
Hour, minute,
second
Month-day
Memo number
Graphic Area
Battery Indicator
AButton
PM indicator
(A for AM)
CButton DButton
Month-day
LButton
(Light)
BButton
Hour, minute,
second
Day of the
Week
City Code Mode Indicator
Stopwatch Mode Alarm Mode
Mode Indicator
Alarm Number
1
Operation Guide 2689
Power Supply
The power supply of this watch uses a solar cell to generate
electrical power, which is stored by a rechargeable battery. Using
or storing the watch where it is not regularly exposed to light, or
allowing it to be blocked from light by your sleeve as you are
wearing it can cause the power of the rechargeable battery to run
down. To ensure stable operation, be sure to allow the watch to
be exposed to light as much as possible when you are wearing or
storing it.
Note that all data in memory and all settings are cleared
whenever you allow the level of the rechargeable battery to
drop to Level 4.
❚
Flashing Recovery Indicator
If you use the light or alarms a number of times during a short
period, a Recovery indicator flashes on the display and the
following operations become disabled as battery power recovers.
• Display illumination
• Alarm and hourly time signal
• Time calibration signal reception
Recovery Indicator
Normal operation will return after the battery recovers.
Display Illumination
An EL (electro luminescent) panel is used to illuminate the display
for easy reading in the dark. An auto light switch automatically
illuminates the display when you angle the watch towards your
face for reading.
❚
To illuminate the display manually
Pressing the L button in any
mode illuminates the digital
display for about 1.5 seconds.
• Pressing the L button
illuminates the display regardless
of whether the auto light switch is
on or off.
You may hear a faint rattling sound when you move the watch
around. This sound is caused by the movement of a metal
bulb that controls operation of the auto light switch, and does
not indicate malfunction.
❚
Battery Indicator
Level 1
Level 2
Level 3
(No display)
Level 4
• Exposing the watch to direct sunlight or other strong light may
cause the battery level indicator to momentarily indicate a level
that is higher than the actual battery level. Because of this, you
should wait for a short while after charging to check the battery
level indicator.
• Even if the battery level drops all the way to Level 4, you will still
be able to recharge the battery and use the watch again.
• When recharging from Level 4, set the current time and date after
the battery level recharges to Level 3. At this time you should
continue to expose the watch to light so it can charge up the Level
2 or Level 1.
❚
Start charging at Level 3!
Battery Level 3 indicates that remaining battery power is very low.
Be sure to expose the watch to light for recharging as soon as
possible after the Level 3 indicator starts to flash.
All functions enabled.
All functions enabled.
Display, display illumination, alarms,
hourly time signal, and signal reception
disabled.
All functions, including digital
timekeeping, disabled.
Illuminating the Display with the
Auto Light Switch
The full auto light switch automatically illuminates the display
display for about 1.5 seconds whenever you angle the watch
towards your face for reading, but only when it is dark.
• The full auto light switch does not illuminate the display
when surrounding light is bright.
The light is very convenient when reading the current time
and other data in the dark.
The auto light switch illuminates the display in all modes.
In the Timekeeping Mode, hold down the L button for about two
seconds to toggle the auto light switch on (auto light switch on
indicator displayed) and off (no indicator displayed).
Auto Light Switch
On Indicator
In any mode, hold down the L button for about two seconds to
toggle the auto light switch on (auto light switch on indicator
displayed) and off (no indicator displayed).
❚
Charging Precautions
Avoid charging the watch in the following locations, and anywhere
else where the watch may become very hot.
• On the dashboard of an automobile parked in the sun
• Very close to an incandescent light source or other sources of
heat
• In a location exposed to direct sunlight for long periods
Note that the display panel may become black under very high
temperatures. This is temporary, and the display will appear
normal again at lower temperatures.
Depending on the light source you are using, the
case of the watch may become quite hot during
charging. Take care to guard against burn injury after
charging.
❚
To charge the battery
Point the solar panel (face) of the watch at a light source.
• Remember that even a partial blockage of the solar cell reduces
charging efficiency.
Example: Positioning the watch
Solar Cell
• The illustration shows the resin band mode.
❚
To illuminate the display
1
With the watch on your
wrist, position it parallel
with the ground.
• You should be wearing the watch on the outside of your wrist
when using the auto light switch.
• Make sure that the left (9 o’clock) and
right (3 o’clock) sides of the watch are
within ±15 degrees of being parallel
with the ground. The auto light switch
may not operate properly if the angle is
greater
2
Rotate your arm so the watch is
angled at about 40 degrees, so you
can read its face.
At least
40°
Display Illumination Precautions
• The light may be difficult to see if you turn it on under bright
sunlight.
• If you press the L button or if an alarm operation starts while the
display is illuminated, illumination will turn off.
• You may notice a slight sound from the watch while the display is
illuminated. This is the sound of EL panel vibration, and does not
indicate malfunction.
❚
Charging Guide
Starting from a full charge, it
should take approximately six
months of operation without
further charging under the
conditions described below
before battery drops to Level 3.
Daily Use (All time values are
approximate.)
• Display Illumination: 1.5
seconds
• Alarms: 10 seconds
• Signal reception: 4 times
• Digital display: 18 hours
Making sure the watch is
regularly exposed to light ensure
stable operation. S
• Charge Times Required to Advance to a Higher Level
Exposure Level
(Brightness)
Outdoor Sunlight
(50,000 lux)
Sunlight Through a
Window (10,000 lux)
Daylight Through a
Window on a Cloudy
Day (5,000 lux)
Indoor Fluorescent
Lighting (500 lux)
• Note that the above charging times are for reference only. Actual
charging time depends on a variety of environmental factors.
Level 4 \ Level 3 \ Level 2 \ Level 1
Required Daily Charging Time
• The following is the daily
amount of charging required
each day to support the
operations under “Daily Use”.
Exposure Level
(Brightness)
Outdoor Sunlight
(50,000 lux)
Sunlight Through a
Window (10,000 lux)
Daylight Through a
Window on a Cloudy Day
(5,000 lux)
Indoor Fluorescent
Lighting (500 lux)
Approximate Charging Time
14 hours1 hour 3 hours
70 hours3 hours 14 hours
143 hours
5 hours
57 hours
28 hours
– – – – – –
Approximate
Charging
Time
5 min.
24 min.
48 min.
8 hr.
Auto Light Precautions
• Frequent use of the auto light can run down the battery.
• The display may not illuminate immediately when you angle the
watch towards your face. This does not indicate malfunction.
• The display remains lit for about 1.5 seconds only, even if you
leave the watch angled towards your face.
• The display may illuminate unintentionally when you wear the
watch on the inside of your wrist, when you shake your arm, or
when you raise your arm. Be sure to turn off the auto light
switch whenever you do not need display illumination.
• Keep the auto light switch turned off whenever you are wearing
the watch on the inside of your wrist.
• Electro-static charge and magnetism can interfere with auto light
operation and even make operation impossible. If this happens,
lower your arm to the starting position and then raise it again. If
you still have trouble with display illumination, try lowering your
arm down to your side and then raise it to your face for reading.
2
Operation Guide 2689
How a Radio-controlled Watch Works
What is a radio-controlled watch?
Your radio-controlled watch is designed to receive a time
calibration signal that contains standard time data and adjust its
current time setting accordingly.
Signal is received using
Transmitter
Cesium
atomic clock
After the watch receives the Standard Time signal, it performs
internal calculations to determine the current time. Because of
this, there may be an error of up to one second in the
displayed time.
Long-wave time
calibration signal
Signal data
Time data
Watch
Internally
built-in antenna.
Decode
Watch decodes
received data and
converts it to time
data.
Time is adjusted
according to time
data.
Location
Reception is difficult and may even be impossible in the locations
described below. Avoid such locations when performing signal
reception.
• You should think of your watch operating like a radio or TV when it
is receiving the calibration signal.
Among or near buildings
Inside a vehicle
(automobile, train, plane, etc.)
In a location where there is radio
interference
(construction site, airport, etc.)
If you are experiencing problems with reception, move away
from the types of locations described above to a location with
better reception, and try again.
Near high-voltage lines
Next to a household appliance
or office equipment
(TV, speaker, fax, PC,
mobile phone, etc.)
Near mountains
Calibration Signal
• The Japanese calibration signal (Call Sign: JJY) is maintained by
the independent Japan Ministry of Posts and Telecommunications
Communication Research Laboratory (CRL). It is a long wave
signal transmitted 24 hours a day from the Mt. Otakadoya
transmitter (40kHz) located in Tamura-gun, Fukushima Prefecture,
and from the Mt. Hagane transmitter (60kHz) located on the
border between Saga Prefecture and Fukuoka Prefecture.
• The U.S. calibration signal (Call Sign: WWVB) is transmitted by
the National Institute of Standards and technology from Fort
Collins, Colorado.
Though the calibration signal is normally transmitted 24 hours
a day, transmission may be interrupted occasionally due to
maintenance, lightening, etc.
Receiving the Calibration Signal
There are two methods you can use to receive the time calibration
signal.
• Auto reception (Reception is performed automatically at
2:00, 3:00, 4:00, and 5:00 each morning.)
• Manual receive (You initiate reception using a button operation.)
• The watch is set up for auto reception at the factory, so all you
need to do is to place it in a location that allows good reception
each night.
❚
To make reception easier
Remove the watch from your wrist and place it somewhere so its
top (12 o’clock side, where the antenna is located) is facing
approximately in the direction of the signal transmitter. Keep it
away from metal objects.
Resin band
Metal band
• Orienting the watch so it is sideways to the transmitter makes it
more difficult to receive the signal.
• Do not move the watch while it is receiving the calibration signal.
Reception Range
This watch is designed to receive the standard time calibration signal of Japan (JJY) or of the United States (WWVB). The signal that is
received depends on the current Home City setting.
• For information about selecting a Home City, see “Setting the Time and Date Manually”.
Home City
TYO
LAX, DEN, CHI, NYC
Transmitter Location
Mt. Hagane
(60kHz)
• Under optimum conditions, the calibration signal should be
receivable up to 1,000 kilometers from the transmitter.
• Note that the wave is relatively weak at distances greater
than 500km, so reception may be poor at long distances.
• Geographic contours, nearby buildings, the season, the time of day, can even make reception impossible even when you are within range of
the transmitter.
• Best reception is possible late at night.
❚
Time Required for Reception
Signal reception takes anywhere from about two to six minutes.
• Note that when “AUTO” is specified as the frequency selection
mode, signal reception can take up to 12 minutes.
• See “Specifying the Transmitter Mode” for more information about
the transmitter mode.
❚
To trigger reception manually
In the Timekeeping Mode, hold
down the D button for about
two seconds until the watch
beeps.
• This indicates that manual receive
has started. The “ ” icon flashes
on the display while signal
reception is in progress.
❚
To stop signal reception
Press the D
• All other buttons besides D are disabled during signal reception.
When reception is successful
The watch terminates reception and adjusts the current time. Next
it beeps and then displays the date and time the adjustment was
performed.
• The “ ” icon on the display also indicates successful signal reception.
The “ ” icon is cleared from the display each day at 3:00 a.m.
When reception fails
The watch does not adjust its current time setting, and displays
“ERR” instead.
• The display will return to the normal timekeeping screen
automatically if you do not perform any operation for about one
or two minutes.
500km
button.
Either the Mt. Otakadoya signal (40kHz) or the Mt.Hagane signal (60kHz)
Fort Collins, Colorado signal
1000km
Mt. Otakadoya
(40kHz)
500km
1000km
❚
The receive indicator cycles from
“Unstable” through “Stable” as
shown below while reception is in
progress. How far it cycles depends
on the signal strength. Keep the
watch in a location where reception
is stable while reception is in
Receive icon
progress.
• Even under optimum reception conditions, it can take about 10
Transmitter
Transmitter Location
1000km
Fort Collins
• Under optimum conditions, the calibration signal should be
receivable up to 3,000 kilometers from the transmitter.
• Note that the wave is relatively weak at distances greater
than 1,000km, so reception may be poor at long distances.
3000km
Receive icon
Unstable Stable
seconds for reception to stabilize.
• Use the receive icon to check reception status and to
determine the best location for signal reception.
• Note that weather, the time of day, surroundings, and other
factors can all affect reception.
3
Operation Guide 2689
❚
To view the last reception date and time
In the Timekeeping Mode, press the D button.
• This displays the date and time that
signal reception was complete and the
current time and date were adjusted.
• To return to the timekeeping screen,
press the D button again.
• The display will return to the normal
timekeeping screen automatically if you
do not perform any operation for about
one or two minutes.
Important!
• The calibration signals received by this
watch include two data groups: an
hour-minute-second group and a yearmonth-day group.
• The “ ” icon is displayed only when
both the hour-minute-second group
and year-month-day group are
received. It will not remain on the
display if only the hour-minute-second
group is received.
Hour-minute-second group and year-month-day group
received
“ ” displayed
Hour-minute-second group only received
“ ” not shown
• If only hour, minute, and second data (no date data) is received,
the last reception date shows the date that the receive operation
was performed (as kept in the Timekeeping Mode).
Icon not shown
Calibration Signal Reception
Precautions
• Auto reception can be performed while the watch is in the
Timekeeping Mode or World Time Mode only.
• Operating any button while auto reception is in progress will
cause the watch to beep and then exit the receive operation.
• Make sure you are within the range of the calibration signal
transmitter before performing the reception operation. Remember
that geographic contours, nearby buildings, the season, the time
of day, can even make reception impossible even when you are
within range of the transmitter.
• Proper reception may be impossible if there is something blocking
the signal. If reception is unsuccessful, try again.
• This watch is designed to adjust its current time setting in
accordance with the calibration signal transmitted in Japan and
the United States only. Note that you will need to make your own
adjustments when using this watch outside of Japan or the United
States, or in any area that is outside the range of one of the
receivable time calibration signal transmitters.
• When the watch is unable to adjust its time signal using the
calibration signal for some reason, timekeeping accuracy is within
±15 seconds per month.
• Strong electrostatic charge can cause timekeeping error.
• Signal reception is cancelled if an alarm starts to sound while it is
being performed.
• The watch’s calendar shows dates up to the year 2099.
Attempting a receive operation after that causes an error.
To turn auto reception on and off
1.
In the Timekeeping Mode,
hold down the A button
for about two seconds
until the current
transmitter selection
mode setting flashes on
the display.
• This is the setting screen.
2. Press the C button three
times.
• This displays the auto
reception setting screen.
3. Press the D button to
toggle auto reception on
or off.
• Press the D button to toggle
auto reception ON and OFF.
4. When the setting you
want is displayed, press
the A button twice to exit
the setting screen.
• This exits the setting screen.
• The display also will exit the setting screen automatically if you do
not perform any operation for about two or three minutes.
Troubleshooting
Cannot perform manual reception.
Cause: • Manual receive can be performed in the
Corrective Measures:• Perform manual receive in the
The “ ” icon is not on the display even though auto signal
reception is turned on.
Cause: • The “ ” icon appears after the watch
Timekeeping Mode only.
• The Home City is set to a city other than
TYO (Tokyo), NYC (New York), CHI
(Chicago), DEN (Denver), or LAX (Los
Angeles).
Timekeeping Mode.
• Change Home City to TYO (Tokyo), NYC
(New York), CHI (Chicago), DEN
(Denver), or LAX (Los Angeles). For
information about selecting a Home City,
see “Setting the Time and Date Manually”.
successfully receives the calibration
signal and adjusts the current time setting.
• A single receive operation was not
successful.
• The “ ” icon is displayed only when both
the hour-minute-second group and yearmonth-day group were received. It will
not remain on the display if only the hourminute-second group is received.
• The watch is not in the Timekeeping Mode
or World Time Mode when an auto
reception time is reached.
Specifying the Transmitter Mode
When Tokyo (TYO) is selected as the Home City, you can select
either of two different transmitters for reception.
• For information about selecting a Home City, see “Setting the
Time and Date Manually”.
1. In the Timekeeping Mode,
hold down the A button
for about two seconds
until the current
transmitter mode setting
flashes on the display.
• This is the setting screen.
2. Press the D button to
cycle through the
available transmitter
mode settings, described
below.
3. When the setting you
want is displayed, press
the A button twice to
exit the setting screen.
• This exits the setting screen.
• The display also will exit the setting screen automatically if
you do not perform any operation for about two or three
minutes.
Corrective Measures:• Check to make sure the watch is in a
Time setting is incorrect following signal reception.
Cause: • Summer time is turned on or the wrong
Corrective Measures:• If the time is advanced by one hour, it
location where it can receive the signal.
• Place the watch in a location where
reception conditions are good.
• Make sure that the watch is in the
Timekeeping Mode or World Time Mode
during the auto reception times.
• Yo u performed manual reception, which
clears the “ ” icon from the display.
Home City is selected.
probably means that summer time
(indicated by the DST indicator on the
display) is turned on. If the time is off by
more than one hour, it probably means
that the Home City is selected. Use the
procedure under “Setting the Time and
Date Manually” to correct the applicable
setting.
FREQUENCY (Frequency)
AUTO
•
With this setting, the watch automatically selects either the
Mt. Otakadoya signal (40kHz) or the Mt. Hagane signal
(60kHz), whichever is strongest.
• The transmitter that was last received successfully is given
priority for the next receive operation.
40
•
With this setting, the watch always receives the Mt. Otakadoya
signal (40kHz).
60
•
With this setting, the watch always receives the Mt. Hagane
signal (60kHz).
If you cannot receive the calibration signal or if the current time
setting is incorrect after signal reception, check the current setup
of the watch.
• The following are the watch’s factory default settings, which are
configured automatically whenever you have the battery of the
watch replaced.
Auto Receive
Transmitter
Home City
Summer Time
On
Auto Japan transmitter select
(40kHz/ 60kHz)
Tokyo
Auto switching in accordance
with signal data
4
World Time Mode
World time lets you display the current time in any one of 30 cities
(29 time zones) around the world.
When you enter the World Time Mode, the screen for the city that
was displayed when you last exited the mode appears first.
Standard Time
in Displayed City
City Code
Home City
(Timekeeping Mode) Time
• After you set the current time for the Home City in the
Timekeeping Mode, the World Time Mode calculates the current
time in other cities around the world using the GMT differential for
each time zone.
• The seconds count in the World Time Mode is linked with the
Timekeeping Mode seconds count.
If a World Time Mode time is incorrect, check the time setting
and time zone setting of the Timekeeping Mode, and correct
them if necessary.
• For information about selecting a Home City and setting the
time, see “Setting the Time and Date Manually”.
Operation Guide 2689
❚
To search for a city
Use the D (+) and B (–)
buttons to scroll through the
city codes until the one you
want is displayed.
• Holding down either button scrolls
at high speed.
• See the “World Time City List” for
information about the display
sequence of the city codes.
(Back)
(Forward)
❚
To turn summer time
(Daylight Saving Time) on and off
You can turn summer time on or off individually for each World
Time city.
1. Use the D (+) and B (–)
buttons to scroll through
the city codes until the
one whose summer time
setting you want to
change is displayed.
• Holding down either button
scrolls at high speed.
2. While the city code you
want is displayed, hold
down the Abutton for
about one second to turn
summer time on (DST
indicator displayed) or off
(DST indicator not
displayed).
• The watch beeps whenever
you change the summer time
setting.
Summer time, or Daylight Saving Time (DST) as is it is called
in some countries, calls for setting clocks ahead one hour
during the summer season. Note that the use of summer time
depends on the country and even the local area.
DST indicator
World Time City List
City Code City Name
– – –
HNL
ANC
LAX
DEN
CHI
NYC
CCS
RIO
Honolulu
Anchorage
Los Angeles
Denver
Chicago
New York
Caracas
Rio De Janeiro
– – –
– – –
GMT
LON
PA R
BER
AT H
CAI
• The contents of the above table are current as of June 2002.
• Time differentials in the above table are in accordance with Universal Time Coordinated (UTC).
Greenwich Mean Time
London
Paris
Berlin
Athens
Cairo
GMT Differential City Code City Name
–11
–10
–9
–8
–7
–6
–5
–4
–3
–2
–1
+0
+0
+1
+1
+2
+2
JRS
JED
THR
DXB
KBL
KHI
DEL
DAC
RGN
BKK
HKG
SEL
TYO
ADL
SYD
NOU
WLG
Jerusalem
Jeddah
Teheran
Dubai
Kabul
Karachi
Delhi
Dakar
Yangon
Bangkok
Hong Kong
Seoul
Tokyo
Adelaide
Sydney
Noumea
Wellington
GMT Differential
+2
+3
+3.5
+4
+4.5
+5
+5.5
+6
+6.5
+7
+8
+9
+9
+9.5
+10
+11
+12
Viewing Time Stamp (Time Memo) Data
Use the C button to enter the Recall Mode.
The Time Stamp function lets you store up to 30 records of time data (month, day, hour, minute, second). Time Stamp records serve as
helpful memos when you need to remember the current date and time for some reason.
• In the Timekeeping Mode, hold down the B button for about one second to create a Time Stamp record.
• Any time you enter the Recall Mode, the record you were viewing when you last exited the Recall Mode appears first, or, if you created a
new Time Stamp record since then, the newly created record appears first.
❚
❚
To view Time Stamp records
In the Recall Mode, use the D
(+) and B (–) buttons to scroll
through Time Stamp records.
• Holding down either button scrolls
at high speed.
Memo number
To delete time stamp records
In the Recall Mode, hold
down the A button for
two or three seconds
• This clears all Time Stamp
records.
• Note that you cannot delete
individual Time Stamp
records.
5
Operation Guide 2689
)
(
)
Start 1st finisher
(Displays time
of 1st finisher.)
2nd finisher Displays time
of 2nd finisher.
Reset
Alarm Mode
Your watch comes with five alarms and an hourly time signal.
❚
Daily Alarms (AL 1 to AL 4)
The watch beeps for about 10 seconds when an alarm time is
reached.
❚
Snooze Alarm (SNZ)
With the snooze alarm, the watch beeps for 10 seconds when the
alarm time is reached, and up to seven times at five-minute
intervals thereafter (approximately 30 minutes total). Pressing any
button stops the beeper, but the alarm will sound again after five
minutes.
❚
Hourly Time Signal
The hourly time signal causes the watch to beep every hour on the
hour.
❚
Testing the Alarm
In the Alarm Mode, hold down the B button to sound the alarm.
To turn an alarm or the hourly time
signal on or off
1.
In the Alarm Mode, use
the D button to display
the screen for the setting
you want to turn on or off.
2. Press the B button to
toggle the currently
display setting on or off.
Alarm Hourly Time Signal
Alarm Indicator
Hourly Time Signal
Indicator
❚
To set an alarm
1. In the Alarm Mode, use
the D button to scroll
through the alarm
screens until the one
whose setting you want to
configure is displayed.
Alarm 1
(AL1)
Hourly Time
Signal (SIG)
2. Hold down the A button
for about two seconds
until the hour digits of the
alarm time start to flash.
• This also causes the alarm
indicator to appear and
automatically turns on the
alarm.
Snooze Alarm
Alarm 2
(AL2)
(SNZ)
Hour
Alarm Number
Alarm 3
(AL3)
Alarm 4
(AL4)
Alarm Indicator
Minute
(Back
Forward
(Back)
(Forward)
6. When all the settings are
the way you want, press
the A button.
• This exits the setting screen.
• The display also will exit the setting screen automatically if
you do not perform any operation for about two or three
minutes.
❚
Stopping the Alarm Beeper
Press any button.
• In the case of the snooze alarm the alarm will sound again in
about five minutes. “SNZ” flashes while the snooze alarm is active
(indicating that the alarm will sound again).
• The snooze alarm will be canceled automatically when any of the
following occurs while the SNZ indicator is flashing on the display.
• If you turn off the snooze alarm in the Alarm Mode
• If you enter the Alarm Mode, and then display the setting
screen.
• If you enter the Timekeeping Mode and then display the setting
screen.
3. Use the D (+) and B (–)
buttons to change the
hour setting.
• Holding down either button
scrolls at high speed.
• When setting the hour, make
sure you specify AM (A) or PM
(P) correctly when using
12-hour timekeeping, or that
you specify the correct 24hour time.
• The same 12-hour/24-hour
format you select for the
Timekeeping Mode time is
also applied in the Alarm
Mode.
4. Press the C button so
the minute setting
flashes.
5. Use the D (+) and B
(–) buttons to change the
minute setting.
• Holding down either button
scrolls at high speed.
Stopwatch Mode
The stopwatch measures elapsed time in units of 1/100 second up to 23 hours, 59 minutes, 59.99 seconds (24 hours). When the
maximum limit is reached, the elapsed time automatically returns to zero and timing continues from there.
❚
Performing Stopwatch Operations
In the Stopwatch Mode, press the D button.
• Each press of the D button starts or stops the stopwatch.
• The graphic display turns on and off every five seconds,
coordinated with Timekeeping Mode time.
Graphic Display
(Split/Reset)
Elapse Time Measurement
Start Stop Reset
Cumulative Time Measurement
Pressing the D button to restart the stopwatch without resetting
it to all zeros resumes elapsed time measurement from where it
was last stopped.
❚
Split Time Measurement
Snooze Alarm
Snooze Indicator
Minutes
HoursSeconds
• Pressing B while timing is being performed freezes the current elapsed time on the display, but timing of the next split continues
internally.
• Changing to another mode while a split time is displayed cancels the split time operation.
• Pressing the B button while timing is stopped resets the stopwatch to all zeros.
1/100-second
(Start/Stop)
❚
Record split Release split ResetStopStart
1st and 2nd Place Finishers
6
Operation Guide 2689
Setting the Time and Date Manually
You can use the following procedure to set the current time and date of the Home City that you have selected in the Timekeeping Mode.
• Always use the Timekeeping Mode to set and adjust the current time and date settings.
Settings
Timekeeping Mode
(Hold down about two seconds.)
Transmitter Mode
Auto Reception Setting
12-24 hour
Power Saving
• While the setting screen (the one with a flashing setting) is on the
display, use the C and A buttons to move the flashing between
settings.
6. While the seconds count
is flashing, press the D
button to reset it to 00.
• Pressing D while the seconds
count is in the range of 30 to
59 resets it to 00 and also
adds 1 to the minutes.
Pressing D in the range of 00
to 29 resets the seconds count
without changing the minutes.
Summer Time
HourSeconds
MonthDay
Resets to 00.
Home City
Minute
Year
To configure settings
1.
In the Timekeeping Mode,
hold down the A button
for about two seconds
until the transmitter
selection mode setting
starts to flash on the
display.
• This is the setting screen.
2. Use the C and A
buttons so the setting you
want to change is flashing
on the display.
8. Press the D button to
toggle Power Saving on
or off.
Use the C and A buttons to select each of the settings and
the D and B buttons to change them.
3. While the Home City code
is flashing, use the D (+)
and B (–) buttons to
scroll through the city
codes.
• Holding down either button
scrolls at high speed.
• See the “World Time City List”
for information about the
display sequence of the city
codes.
4. While the summer time
setting is flashing, press
the D button to cycle
through the summer time
settings until the one you
want is displayed.
• Available settings are AUTO, OFF, and ON.
Summer time, or Daylight Saving Time (DST) as is it is called
in some countries, calls for setting clocks ahead one hour
during the summer season.
Note that the use of summer time depends on the country and
even the local area. Note that the use of summer time
depends on the country and even the local area.
City Code
AUTO
•
This setting enables the auto summer time setting, which
turns summer time on or off in accordance with the received
time calibration signal.
• This setting uses Japan summer time data when TYO is
selected as the Home City code, and U.S. summer time
data when NYC, CHI, DEN, or LAX is selected as the
Home City code.
In the United States, Daylight Saving Time (summer time)
is from 2:00 a.m. on the first Sunday in April until 1:00 a.m.
on the last Sunday in October.
OFF
•
This setting turns off summer time and displays the current
time normally.
On
•
This setting turns on summer time and advances the current
time by one hour.
• The DST indicator appears on the display while summer
time is turned on.
• Note that the above setting toggles between “OFF” and “On”
when any city code other than HKG, SEL, TYO, NYC, CHI, DEN,
LAX, ANC, or HNL is selected as the Home City.
5. While the 12/24-hour
timekeeping setting is
flashing, press the D
button to select the
setting you want.
• Pressing D toggles the
timekeeping format between
12-hour (“12H” indicator) and
24-hour (24H indicator).
12/24-hour
7. While the hour, minute,
year, month, or day
setting is flashing, use the
D (+) and B (–) buttons
to change the setting.
• Holding down either button
scrolls at high speed.
• When setting the hour,
make sure you specify AM
(A) or PM (P) correctly, or
that you specify the correct
24-hour time.
• You can set a date in the range of January 1, 2000 to
December 31, 2099.
• The day of the week is set automatically in accordance with
the date you set.
Hour
Month
Minute
YearDay
(Back)
(Forward)
Seconds
9. When all the settings are
the way you want, press
the A button.
• The figures on the display stop flashing.
• The display also will exit the setting screen automatically if
you do not perform any operation for about two or three
minutes.
The watch automatically makes adjustments for leap years
and month lengths.
7
Loading...