MO0907-EA
l
l
l
l
l
l
l
l
l
l
l
l
l
l
Operation Guide 3192
Getting Acquainted
Congratulations upon your selection of this CASIO watch. To get the most out of your
purchase, be sure to read this manual carefully.
Keep the watch exposed to bright light
Bright Light
l
l
l
l
l
l
Solar cell
• The watch continues to operate, even when it is not exposed to light. Leaving the
watch in the dark can cause the battery to run down, which will result in some watch
functions to be disabled. If the battery goes dead, you will have to re-configure watch
settings after recharging. To ensure normal watch operation, be sure to keep it
exposed to light as much as possible.
Battery charges in the light. Battery discharges in the dark.
Solar cell
(Converts light to
electrical power.)
Charge
The electricity generated by the solar cell of the watch is
l
stored by a rechargeable battery. Leaving or using the
l
l
l
l
watch where it is not exposed to light causes the battery to
run down. Make sure the watch is exposed to light as
much as possible.
• When you are not wearing the watch on your wrist,
position the face so it is pointed at a source of bright
light.
• You should try to keep the watch outside of your sleeve
as much as possible. Charging is reduced significantly if
the face is covered only partially.
Bright Light
Electrical
energy
All
LEVEL 1
functions
LEVEL 2
enabled
LEVEL 3
LEVEL 4
Rechargeable battery
Dis-
charge
LEVEL 1
LEVEL 2
LEVEL 3
LEVEL 4
Some or all
functions
disabled
• The actual level at which some functions are disabled depends on the watch model.
• Frequent display illumination can run down the battery quickly and require charging.
The following guidelines give an idea of the charging time required to generate
enough power for normal daily operations.
Approximately 5 minutes exposure to bright sunlight coming in through a window
Approximately 8 hours exposure to indoor fluorescent lighting
• Be sure to read “Power Supply” for important information you need to know
when exposing the watch to bright light.
If the display of the watch is blank...
If the display of the watch is blank, it means that the watch’s Power Saving function
has turned off the display to conserve power.
• See “Power Saving Function” for more information.
Note that CASIO COMPUTER CO., LTD. assumes no responsibility for any damage
or loss suffered by you or any third party arising through the use of this product or
its malfunction.
About This Manual
• Depending on the model of your watch, display text appears either as dark figures
on a light background or light figures on a dark background. All sample displays in
this manual are shown using dark figures on a light background.
• Button operations are indicated using the letters shown in the illustration.
• Each section of this manual provides you with the information you need to perform
operations in each mode. Further details and technical information can be found in
the “Reference” section.
General Guide
• Press C to change from mode to mode.
• In any mode, press L to illuminate the display.
Timekeeping Mode
Press C.
▲
Timekeeping
Current Time
Day of week
PM
indicator
Read This Before You Set the Time and Date!
This watch is preset with a number of city codes, each of which represents the time
zone where that city is located. When setting the time, it is important that you first
select the correct city code for your Home City (the city where you normally use the
watch). If your location is not included in the preset city codes, select the preset city
code that is in the same time zone as your location.
• Note that all of the times for the World Time Mode city codes are displayed in
accordance with the time and date settings you configure in the Timekeeping Mode.
To set the time and date
Month – Day
▲
Dual Time
l
l
l
l
l
l
l
l
Press the B button to toggle between the day of the
week and date, and the currently selected World Time city
and time (Dual Time).
Use the Timekeeping Mode to set and view the current
time and date.
Hour : Minutes
Seconds
▲
BB
City code
Dual time
1. In the Timekeeping Mode hold down A until the city
l
l
l
code starts to flash, which indicates the setting screen.
l
l
2. Use D and B to select the city code you want.
l
• Make sure you select your Home City code before
changing any other setting.
Alarm ModeWorld Time Mode
▲
Countdown Timer Mode
▲
4. When the timekeeping setting you want to change is flashing, use D or B to
change it as described below.
5. Press A to exit the setting screen.
To specify your Home City
To do this: Do this:Screen:
Specify your Home City
Cycle between Daylight Saving
) and Standard Time
Time (
).
(
Toggle between 12-hour ( )
and 24-hour ( ) timekeeping
Reset the seconds to zero (
Change the hour and minutes
Change the year, month and day
Toggle between Button Operation
Tone on( ) and off ( )
Toggle the display illumination
duration between 1.5 seconds
( ) and three seconds ( )
Toggle between Power Saving on
(
) and off ( )
City code
1. In the Timekeeping Mode, hold down A { til the city
code starts to flash, which indicates the setting screen.
2. Press D (east) and B (west) to select the city code
you want to use as your Home City.
• For full information on city codes, see the “UTC
Differential/City Code List”.
3. Press A to exit the setting screen.
▲
Stopwatch Mode
Use D (east) and B (west).
Press D.
Press D.
)
Press D.
Use D (+) and B (–).
Press D.
Press D.
Press D.
▲
• For full information on city codes, see the “UTC Differential/City Code List”.
3. Press C to move the flashing in the sequence shown below to select the other
setting.
City Code
12/24-Hour
Illumination
Duration
Format
Operation
Tone
Seconds
DayPower Saving
Hour
Month Year
MinutesDST
PM
indicator
Seconds
Hour : Minutes
1
Operation Guide 3192
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
Daylight Saving Time (DST)
Daylight Saving Time (summer time) advances the time setting by one hour from
Standard Time. Remember that not all countries or even local areas use Daylight
Saving Time.
To change the Daylight Saving Time (summer time) setting
DST indicator
4. When the setting you want is selected, press A to exit the setting screen.
• The DST indicator appears to indicate that Daylight Saving Time is turned on.
12-hour and 24-hour timekeeping
• With the 12-hour format, the P (PM) indicator appears to the left of the hour digits for
times in the range of noon to 11:59 p.m. and no indicator appears to the left of the
hour digits for times in the range of midnight to 11:59 a.m.
• With the 24-hour format, times are displayed in the range of 0:00 to 23:59, without
the P (PM) indicator.
• The 12-hour/24-hour timekeeping format you select in the Timekeeping Mode is
applied in all other modes.
Others
• The day of the week is displayed automatically in accordance with the date (year,
month and day) settings.
• Button operation tone on and off
• Illumination duration
• Power Saving on and off
1. In the Timekeeping Mode, hold down A until the city
code starts to flash, which indicates the setting screen.
2. Press C and the DST setting screen appears.
3. Use D to cycle through the DST settings in the
sequence shown below.
DST off ( ) DST on ( )
World Time
City code
Current time in
selected city
• All of the operations in this section are performed in the World Time Mode, which
you enter by pressing C.
To view the time in another city
While in the World Time Mode, use the D (eastward) and B (westward) buttons to
scroll through the city codes (time zones). Holding down either button scrolls at high
speed.
• Pressing the D and B buttons at the same time will jump to the UTC time zone.
To toggle a city code time between Standard Time and Daylight Saving Time
DST indicator
• You can turn on DST individually for each city code, except UTC.
• Turning on DST for the city code that is currently selected as your Home City will
turn on DST for normal timekeeping.
World Time shows the current time in 48 cities (31 time
zones) around the world.
• The times kept in the World Time Mode are
synchronized with the time being kept in the
Timekeeping Mode. If you feel that there is an error in
any World Time Mode time, check to make sure you
have the correct city selected as your Home City. Also
check to make sure that the current time as shown in
the Timekeeping Mode is correct.
• Select a city code in the World Time Mode to display the
current time in any particular time zone around the
globe. See the “UTC Differential/City Code List” for
information about the UTC differential settings that are
supported.
1. In the World Time Mode, use D and B to display the
city code (time zone) whose Standard Time/Daylight
Saving Time setting you want to change.
2. Hold down A to toggle between Daylight Saving Time
(DST indicator displayed) and Standard Time (DST
indicator not displayed).
• The DST indicator is shown on the World Time Mode
screen while Daylight Saving Time is turned on.
Alarms
Alarm number
Current Time
Alarm time
(Hour : Minutes)
To set an alarm time
• To set a daily alarm, display alarm screen , , and . To set the
snooze alarm, display the
• The snooze alarm repeats every five minutes.
2. After you select an alarm, hold down A until the hour setting of the alarm time
starts to flash, which indicates the setting screen.
• This operation turns on the alarm automatically.
3. Press C to move the flashing in the sequence shown below.
You can set up to five independent daily alarms with hour
and minutes. When an alarm is turned on, the alarm tone
sounds when the alarm time is reached. One of the
alarms is a snooze alarm, while the other four are usual
daily alarms.
You also can turn on an Hourly Time Signal that causes
the watch to beep twice every hour on the hour.
• There are five alarm screens numbered
and for the daily alarm, and a snooze alarm
screen indicated by
screen is indicated by
• All of the operations in this section are performed in the
Alarm Mode, which you enter by pressing C.
1. In the Alarm Mode, use D to scroll through the alarm
screens until the one whose time you want to set is
displayed.
screen.
Hours Minutes
. The Hourly Time Signal
.
, ,
4. Use D (+) and B (–) to change the hour and minutes.
• With the 12-hour format, set the time correctly as a.m. or p.m. (P indicator).
5. Press A to exit the setting screen.
Alarm Operation
The alarm tone sounds at the preset time for 10 seconds, regardless of the mode the
watch is in. In the case of the snooze alarm, the alarm operation is performed a total
of seven times, every five minutes, until you turn the alarm off.
• Alar m and Hourly Time Signal operations are performed in accordance with the
Timekeeping Mode time.
• To stop the alarm tone after it starts to sound, press any button.
• Performing any one of the operations below during a 5-minute interval between
snooze alarms cancels the current snooze alarm operation.
Displaying the Timekeeping Mode setting screen
Displaying the
To test the alarm
In the Alarm Mode, hold down D to sound the alarm.
To turn an alarm on and off
Snooze
alarm
indicator
To turn the Hourly Time Signal on and off
Hourly time signal on
indicator
Alarm number
on
Alarm on
indicator
Current time
setting screen
1. In the Alarm Mode, use D to select an alarm.
2. Press B to toggle it on and off.
• Turning on a alarm (
displays the alarm on indicator (
screen.
• In all modes, the alar m on indicator is shown for any
alarm that is currently turned on.
• The alar m on indicator flashes while the alarm is
sounding.
• The snooze alar m indicator (
snooze alarm is sounding and during the 5-minute
intervals between alarms.
1. In the Alarm Mode, use D to select the Hourly Time
Signal (
2. Press B to toggle it on and off.
• The Hour ly Time Signal on indicator (
display in all modes while this function is turned on.
, , and or )
).
) on its Alarm Mode
) flashes while the
) is shown on the
Stopwatch
The stopwatch lets you measure elapsed time, split times,
and two finishes.
• The display range of the stopwatch is 23 hours,
59 minutes, 59.99 seconds.
• The stopwatch continues to run, restar ting from zero
after it reaches its limit, until you stop it.
• The stopwatch measurement operation continues even
Minutes
Seconds
1/100 second
To measure times with the stopwatch
Elapsed Time
D
Start Stop
Split Time
D
Start Split
Two Finishes
D
Start Split
if you exit the Stopwatch Mode.
Hours
• Exiting the Stopwatch Mode while a split time is frozen
on the display clears the split time and returns to
elapsed time measurement.
• All of the operations in this section are performed in the
Stopwatch Mode, which you enter by pressing C.
D ➤
➤
B
➤
(SPL displayed)
B
➤
First runner finishes.
Display time of first
runner.
D
Re-start Clear
B
➤
Split release
D
➤
Stop
Second runner
finishes.
D
➤
Stop
D
➤
Stop
B
➤
Split release
Display time of
second runner.
➤
➤
➤
B
B
Clear
B
Clear
Countdown Timer
You can set the countdown timer within a range of one
minute to 24 hours. An alarm sounds when the countdown
reaches zero.
• All of the operations in this section are performed in the
Countdown Timer Mode, which you enter by pressing
C.
Seconds
Hours
Minutes
To configure the countdown timer
2. Press C to move the flashing in the sequence shown below.
3. Use D (+) and B (–) to change the Hours and Minutes.
• To specify a countdown start time of 24 hours, set
4. Press A to exit the setting screen.
1. While the countdown start time is on the display in the
Countdown Timer Mode, hold down A until the current
countdown start time starts to flash, which indicates the
setting screen.
• If the countdown start time is not displayed, use the
procedure under “To use the countdown timer” to
display it.
Hours Minutes
.
2
Operation Guide 3192
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
To use the countdown timer
Countdown start time
l
l
l
l
l
l
l
l
l
l
Current timer time
Countdown End Beeper
The countdown end beeper lets you know when the countdown reaches zero. The
beeper stops after about 10 seconds or when you press any button.
Press D while in the Countdown Timer Mode to start the
countdown timer.
• The countdown timer operation continues even if you
exit the Countdown Timer Mode.
• Press D while a countdown operation is in progress to
pause it. Press D again to resume the countdown.
• To stop a countdown operation completely, first pause it
(by pressing D), and then press B. This returns the
countdown time to its starting value.
Illumination
This watch has an EL (electro-luminescent) panel that
causes the entire display to glow for easy reading in the
dark. The watch’s auto light switch turns on illumination
automatically when you angle the watch toward your face.
• The auto light switch must be turned on (indicated by
the auto light switch on indicator) for it to operate.
• See “Illumination Precautions” for other important
information about using illumination.
To illuminate the display manually
Auto light switch on
indicator
• You can use the procedure below to select either 1.5 seconds or 3 seconds as the
illumination duration. When you press L, the illumination will remain on for about
1.5 seconds or 3 seconds, depending on the current illumination duration setting.
To specify the illumination duration
l
l
l
About the Auto Light Switch
Turning on the auto light switch causes illumination to turn on, whenever you position
your wrist as described below in any mode. Note that this watch features a “Full Auto
EL Light”, so the auto light switch operates only when available light is below a certain
level. It does not turn on the backlight under bright light.
Moving the watch to a position that is parallel to the ground and then tilting it toward
you more than 40 degrees causes illumination to turn on.
• Wear the watch on the outside of your wrist.
Warning!
••
• Always make sure you are in a safe place whenever you are reading the
••
display of the watch using the auto light switch. Be especially careful when
running or engaged in any other activity that can result in accident or injury.
Also take care that sudden illumination by the auto light switch does not
startle or distract others around you.
••
• When you are wearing the watch, make sure that its auto light switch is turned
••
off before riding a bicycle or operating a motorcycle or any other motor
vehicle. Sudden and unintended operation of the auto light switch can create a
distraction, which can result in a traffic accident and serious personal injury.
To turn the auto light switch on and off
In the Timekeeping Mode, hold down L for about three seconds to toggle auto light
switch on (indicator
• The auto light switch on indicator (
the auto light switch is turned on.
In any mode, press L to turn on illumination.
• The above operation turns on illumination regardless of
the current auto light switch setting.
1. In the Timekeeping Mode, hold down A until the
l
l
l
l
display contents start to flash. This is the setting screen.
2. Press C 10 times to display the current illumination
l
l
duration (
l
3.
Press D to toggle the setting between (1.5 seconds)
and
4. Press A to exit the setting screen.
is shown on the display) and off.
or ).
(three seconds).
Parallel to
ground
) is shown on the display in all modes while
More than 40°
Power Supply
This watch is equipped with a solar cell and a rechargeable battery that is charged by
the electrical power produced by the solar cell. The illustration shown below shows
how you should position the watch for charging.
Example: Orient the watch so its face is
pointing at a light source.
• The illustration shows how to position
a watch with a resin band.
• Note that charging efficiency drops
when any part of the solar cell is
blocked by clothing, etc.
• You should try to keep the watch
outside of your sleeve as much as
possible. Charging is reduced
significantly if the face is covered only
partially.
Important!
• Storing the watch for long periods in an area where there is no light or wearing it in
such a way that it is blocked from exposure to light can cause rechargeable battery
power to run down. Be sure that the watch is exposed to bright light whenever
possible.
Solar cell
• This watch uses a rechargeable battery to store power produced by the solar cell, so
regular battery replacement is not required. However, after very long use, the
rechargeable battery may lose its ability to achieve a full charge. If you experience
problems getting the rechargeable battery to charge fully, contact your dealer or
CASIO distributor about having it replaced.
• Never try to remove or replace the watch’s rechargeable battery yourself. Use of the
wrong type of battery can damage the watch.
• The current time and all other settings return to their initial factory defaults whenever
battery power drops to Level 5 and when you have the battery replaced.
• Turn on the watch’s Power Saving function and keep it in an area normally exposed
to bright light when storing it for long periods. This helps to keep the rechargeable
battery from going dead.
Battery Power Indicator and Recover Indicator
The battery power indicator on the display shows you the current status of the
rechargeable battery’s power.
Battery Power Indicator
Level
1
2
3
Battery power
indicator
• The flashing indicator at Level 3 tells you that battery power is very low, and
that exposure to bright light for charging is required as soon as possible.
• At Level 5, all functions are disabled and settings return to their initial factory
defaults. Once the battery reaches Level 2 after falling to Level 5, reconfigure the
current time, date and other settings.
• The watch’s Home City code setting will change automatically to TYO (Tokyo)
whenever the battery drops to Level 5 or when you have the rechargeable battery
replaced.
• Display indicators reappear as soon as the battery is charged from Level 5 to
Level 2.
• Leaving the watch exposed to direct sunlight or some other very strong light source
can cause the battery power indicator to show a reading temporarily higher than the
actual battery level. The correct battery level should be indicated after a few minutes.
Recover indicator
Charging Precautions
Certain charging conditions can cause the watch to become very hot. Avoid leaving
the watch in the areas described below whenever charging its rechargeable battery.
Also note that allowing the watch to become very hot can cause its liquid crystal
display to black out. The appearance of the LCD should become normal again when
the watch returns to lower temperature.
Warning!
Leaving the watch in bright light to charge its rechargeable battery can cause it
to become quite hot. Take care when handling the watch to avoid burn injury.
The watch can become particularly hot when exposed to the following
conditions for long periods.
• On the dashboard of a car par ked in direct sunlight
• Too close to an incandescent lamp
• Under direct sunlight
Charging Guide
After a full charge, timekeeping remains enabled for up to about 11 months.
• The following table shows the amount of time the watch needs to be exposed to light
each day in order to generate enough power for normal daily operations.
Exposure Level (Brightness)
Outdoor Sunlight (50,000 lux)
Sunlight Through a Window (10,000 lux)
Daylight Through a Window on a Cloudy Day (5,000 lux)
Indoor Fluorescent Lighting (500 lux)
• For details about the battery operating time and daily operating conditions, see the
“Power Supply” section of the Specifications.
• Stable operation is promoted by frequent exposure to light.
Recovery Times
The table below shows the amount exposure that is required to take the battery from
one level to the next.
Exposure Level
(Brightness)
Outdoor Sunlight
(50,000 lux)
Sunlight Through a
Window (10,000 lux)
Daylight Through a
Window on a Cloudy
Day (5,000 lux)
Indoor Fluorescent
Lighting (500 lux)
• The above exposure time values are all for reference only. Actual required exposure
times depend on lighting conditions.
4
5
l
l
l
l
l
l
l
(Charge Soon Alert)
• Performing illumination or beeper operations during a
short period may cause
display. Illumination, alarm, countdown timer alarm and
hourly time signal will be disabled until battery power
recovers.
After some time, battery power will recover and
(recover) will disappear, indicating that the above
functions are enabled again.
• If
(recover) appears frequently, it probably means
that remaining battery power is low. Leave the watch in
bright light to allow it to charge.
Approximate Exposure Time
Level 5 Level 4 Level 3 Level 2 Level 1
170 hours - - - - - - - - - - - - - - - -
l
l
l
l
l
l
l
l
l
l
2 hours 20 hours 6 hours
8 hours 98 hours 27 hours
15 hours 200 hours 54 hours
l
l
l
l
l
l
l
l
l
l
l
l
l
Function Status
All functions enabled.
All functions enabled.
Illumination, and beeper
l
disabled.
l
Except for the CHG (charge)
indicator, all functions and
display indicators disabled.
All functions disabled.
(recover) to appear on the
Approximate
Exposure Time
5 minutes
24 minutes
48 minutes
8 hours
▲
▲
▲
3
Operation Guide 3192
Reference
This section contains more detailed and technical information about watch operation.
It also contains important precautions and notes about the various features and
functions of this watch.
Button Operation Tone
MUTE indicator
To turn the button operation tone on and off
1. In the Timekeeping Mode, hold down A until the display contents start to flash.
This is the setting screen.
2. Press C nine times to display the current button operation tone setting (
).
3. Press D to toggle the button operation tone on (
4. Press A to exit the setting screen.
• The MUTE indicator is displayed in all modes when the button operation tone is
turned off.
Power Saving Function
Power saving on indicator
Elapsed Time
in Dark
60 to 70 minutes
6 or 7 days
• Wearing the watch inside the sleeve of clothing can cause it to enter the sleep state.
• The watch will not enter the sleep state between 6:00 AM and 9:59 PM. If the watch
is already in the sleep state when 6:00 AM arrives, however, it will remain in the
sleep state.
To recover from the sleep state
Perform any one of the following operations.
• Move the watch to a well-lit area.
• Press any button.
• Angle the watch toward your face for reading.
To turn Power Saving on and off
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
l
On/Off status
Auto Return
If you do not perform any operation for about two or three minutes while a setting
screen (with a flashing setting) is on the display, the watch will exit the setting screen
automatically.
Scrolling
The B and D buttons are used in various modes and setting screens to scroll
through data on the display. In most cases, holding down these buttons during a scroll
operation scrolls at high speed.
Initial Screens
When you enter the World Time Mode, or Alarm Mode, the data you were viewing
when you last exited the mode appears first.
Timekeeping
• Resetting the seconds to while the current count is in the range of 30 to 59
causes the minutes to be increased by 1. In the range of 00 to 29, the seconds are
reset to
• The year can be set in the range of 2000 to 2099.
• The watch’s built-in full automatic calendar makes allowances for different month
• The current time for all city codes in the Timekeeping Mode and World Time Mode is
World Time
The seconds count of the World Time is synchronized with the seconds count of the
Timekeeping Mode.
Illumination Precautions
• The electro-luminescent panel that provides illumination loses power after very long
• Illumination may be difficult to see when viewed under direct sunlight.
• The watch may emit an audible sound whenever the display is illuminated. This is
• Illumination turns off automatically whenever an alarm sounds.
• Frequent use of illumination runs down the battery.
without changing the minutes.
lengths and leap years. Once you set the date, there should be no reason to change
it except after you have the watch’s battery replaced or the battery drops to Level 5.
calculated in accordance with the Coordinated Universal Time (UTC) for each city,
based on your Home City time setting.
use.
due to vibration of the EL panel used for illumination, and does not indicate
malfunction.
The button operation tone sounds any time you press one
of the watch’s buttons. You can turn the button operation
tone on and off as desired.
• Even if you turn off the button operation tone, the
alarms, the Hourly Time Signal, and the countdown
alarm all operate normally.
) or off ( ).
When turned on, the Power Saving function enters a sleep
state automatically whenever the watch is left in an area
for a certain period where it is dark. The table below
shows how watch functions are affected by the Power
Saving function.
Display
Blank, with Power Saving
on indicator ( ) flashing
Blank, with Power Saving
on indicator (
(not flashing)
) displayed
1. In the Timekeeping Mode, hold down A until the city
code starts to flash, which indicates the setting screen.
2. Press C eleven times until the Power Saving on/off
screen appears.
3. Press D to toggle Power Saving on (
(
).
4. Press A to exit the setting screen.
• The Power Saving on indicator (
modes while Power Saving is turned on.
All functions enabled, except for the
display
Beeper tone, illumination, and display
are disabled.
Operation
) is displayed in all
or
) and off
Auto light switch precautions
• Avoid wearing the watch on the inside of your wrist. Doing so causes the auto light
switch to operate when it is not needed, which shortens battery life. If you want to
wear the watch on the inside of your wrist, turn off the auto light switch feature.
Lower than 15 degrees to
illuminate
• Static electr icity or magnetic force can interfere with proper operation of the auto
light switch. If illumination does not turn on, try moving the watch back to the starting
position (parallel with the ground) and then tilt it back toward you again. If this does
not work, drop your arm all the way down so it hangs at your side, and then bring it
back up again.
• Under cer tain conditions, illumination may not turn on until about one second after
you turn the face of the watch toward you. This does not necessarily indicate
malfunction of the auto light switch.
• You may notice a very faint clicking sound coming from the watch when it is shaken
back and forth. This sound is caused by mechanical operation of the auto light
switch, and does not indicate a problem with the watch.
• Illumination may not turn on if the face of the watch is
more than 15 degrees above or below parallel. Make
sure that the back of your hand is parallel to the ground.
• Illumination tur ns off after a preset amount of time (1.5
or 3 seconds), even if you keep the watch pointed
toward your face.
Specifications
Accuracy at normal temperature: ± 15 seconds a month
Timekeeping: Hour, minutes, seconds, p.m. (P), month, day, day of the week
Time format: 12-hour and 24-hour
Calendar system: Full Auto-calendar pre-programmed from the year 2000 to 2099
Other: Home City (can be assigned one of 48 cities); Standard Time / Daylight
Saving Time (summer time)
World Time: 48 cities (31 time zones)
Other: Daylight Saving Time/Standard Time
Alarms: 5 daily alarms (four daily alarms; one snooze alarm); Hourly Time Signal
Stopwatch:
Measuring unit: 1/100 second
Measuring capacity: 23:59' 59.99''
Measuring modes: Elapsed time, split time, two finishes
Countdown Timer:
Measuring unit: 1 second
Input range: 1 minute to 24 hours (1-minute increments and 1-hour increments)
Illumination: EL (electro-luminescent panel); Full Auto Light Switch; Selectable
illumination duration
Other: Button operation tone on/off, Power saving on/off
Power Supply: Solar cell and one rechargeable battery
Approximate battery operating time: 11 months (from full charge to Level 4)
under the following conditions:
• Watch not exposed to light
• Internal timekeeping
• Display on 18 hours per day, sleep state 6 hours per day
• 1 illumination operation (1.5 second) per day
• 10 seconds of alar m operation per day
Frequent use of illumination runs down the battery. Particular care is required
when using the auto light switch.
UTC Differential/City Code List
City
Code Differential
PPG
HNL
ANC
YVR
LAX
YEA
DEN
MEX
CHI
NYC
SCL
YHZ
YYT
RIO
FEN
RAI
UTC
LIS
LON
MAD
PA R
ROM
BER
STO
AT H
CAI
JRS
City
Pago Pago
Honolulu
Anchorage
Vancouver
Los Angeles
Edmonton
Denver
Mexico City
Chicago
New York
Santiago
Halifax
St. Johns
Rio De Janeiro
Fernando De
Noronha
Praia
Lisbon
London
Madrid
Paris
Rome
Berlin
Stockholm
Athens
Cairo
Jerusalem
UTC
–11
–10
–9
–8
–7
–6
–5
–4
–3.5
–3
–2
–1
+0
+1
+2
City
Code Differential
MOW
JED
THR
DXB
KBL
KHI
DEL
KTM
DAC
RGN
BKK
SIN
HKG
BJS
TPE
SEL
TYO
ADL
GUM
SYD
NOU
WLG
• Based on data as of December 2008.
• The rules governing global times
(GMT differential and UTC offset) and
summer time are determined by each
individual country.
City
Moscow
Jeddah
Tehran
Dubai
Kabul
Karachi
Delhi
Kathmandu
Dhaka
Yangon
Bangkok
Singapore
Hong Kong
Beijing
Taipei
Seoul
Tokyo
Adelaide
Guam
Sydney
Noumea
Wellington
UTC
+3
+3.5
+4
+4.5
+5
+5.5
+5.75
+6
+6.5
+7
+8
+9
+9.5
+10
+11
+12
4
Loading...