GSD Wi-Corporate Controller Installation & User Manual

Installation & User Manual V2.07

3

Contents

6

Installation Diagrams

9

8

System Overview

Wi-Corporate Controller

Other products from GSD

4

Installation Instructions

12

Network Diagrams

Wiring Diagrams

19

Fingerprint Enrollment

Operation Instructions

Global Security Devices Ltd: No.3 Broomhill Business Complex, Tallaght,

Dublin 24, Ireland, Phone: [phone], Email: [e-mail]

www.globalsecurity.ie

YOUR SECURITY IS OUR PRIORITY

2

3

Technical Specification

Power Supply 230 VAC
Current consumption 30mA
Fuse Rating 230VAC 315mA T
Moisture Resistance Indoor Use Only
Dimensions W. 260mm D. 262mm H. 55mm

Technical Specs - GSD Wi-Corporate Controller

Power Supply 12 DC
Current consumption 110mA
Current consumption with load (max) 145mA
Relay Contact Rating 5 Amps /230V ac
Operating Temperature - 20 C to +60 C
Moisture Resistance IP 67 ( IP65 on Wi-Bio )
Dimensions - Flush Mount W. 87mm D. 21mm H. 119mm

- Surface Mount W. 87mm D. 35mm H. 119mm

Technical Specs - Wi-

Corporate

Door Controls

Features

Doors controlled
Users
User Groups
Time Zones
Door Groups
Reporting Facility
Challenge Facility
Logging
Input/Output Mapping
Supports Wireless & RS485 Networks
Automatic Backup Facility
Database Encryption
* 30000 individual usergroups are available

20

30000

128*

128
128

Yes
Yes

Unlimited

CCTV & Lift control

Yes
Yes
Yes

Installation Steps

Step Description Page

1 Install the Controller using the Installation Diagrams 4-5

2 Wire the Controller using the Wiring Diagrams 8

3 Install and wire each Door Control. Refer to the Door Control
Manual for instructions.

4 Connect the Controller to the PC using Network Diagrams 9-11

5 Restoring Factory Defaults 11

6 Setting up TCP-IP 12

6 Phase 1- Setting up the GSD Controller 14

7 Phase 2 - Configuring the GSD Controller 15

8 Phase 3 - Enrolling Door Controls 16-18

9 Phase 4 - Configuring Users 19

10 Phase 5 - Configuring Access Levels 20

11 Phase 6 - Downloading Configuration 20

12 Enrolling User Fingerprints 21

13 Correct Finger Placement techniques 22-25

Installation Steps

Control Panel opening

Control Panel features

remove screw cap

remove retaining
screw

to remove cover
pull forward on
right and slide left

mount with 4 x 1.5 inch
No. 8 Security Type screws

rear tamper
switch

cable
entry

cable
entry

cable
entry

cable
entry

spare cap

access to rear
void for wiring

spirit level

mains pcb

mount holemount hole

mount hole

4

Installation Diagrams

5

Installation Diagrams

6

System Overview

Wireless Connection to Door Controls

Door Control
#1

Door Control
#2

Door Control
#3

Door Control
#5 - 20

TCP-IP connection to Controllers
or
RS485 Network to Controllers
Max number of Controllers 3
Max Cable Length 1.4 km

Controller
#1

Controller

#2 - 3

Door Control
#4

Note: Door Controls can be installed within 30 meters
of the Controller or within 30 meters of any other Door Control
as each Door Control will function as a repeater. Each Door Control
transmits data to/from the Controller. These distances are a guideline.
The actual communication range depends on building shape and
construction methods used.

7

System Overview

Note: If using a single Controller,
an RS232 cable may be used.
Max cable length 10 meters

RS485 Connection to Door Controls

Door Control
#1

Door Control
#2

Door Control
#3

Door Control
#4 - 20

RS485 Network to Door Controls
Max Cable Length 1.4 km.
Daisy Chain Configuration Only.

Controller
#1

Controller

#2 - 3

Note: If using a single Controller,
an RS232 cable may be used.
Max cable length 10 meters

Place a 120ohm
Termination Resistor
across A & B on the last
Door Control in the chain.

Place a 120ohm
Termination Resistor
across A & B on the
Controller

TCP-IP connection to Controllers
or
RS485 Network to Controllers
Max number of Controllers 3
Max Cable Length 1.4 km

Note : Used ONLY for
Wired 485 Network
Connections.

ABCOM

TX

RX

PC Network

PC Direct

PC Network Connections
can be used for multiple
controllers See page
10 for wiring

Wiring Diagrams

8

Wiring Diagrams

Door Network

A

B

COM

1 2 3 4

OFF

ON

TCP_IP

3V Lithium

Inputs/outputs

IP1
IP2
0V
IP3
IP4
12V
OP1
OP2

OP3
OP4
0V
VOUT
DAT
CLK
SEN

Inputs/outputs

Cable Tie

Fuse Rating : 230VAC 315mA

Warning : Installation should only be carried out
by a suitably qualified person only.

Cable Tie
retaining
clips

Main Input Cable
230VAC

Neutral
Earth

Live

Remove Battery Tab

Pull

9

Network Diagrams for Single Controller

A
B
0V
TX
RX

A
B
0V

Door Network

PC Network

Connect DB9 cable
to serial port on PC

Maximum cable
length 10 meters

Direct Connect - All Dip Switches OFF

PC Direct

DB9 Female
Serial Cable

PC Direct Connection can be used, when
using ONLY one GSD Controller.

Set the Direct address to
ALL dip switches OFF
(see below )

Network Diagrams

OFF

ON

1 2 3 4

1

5

2
3
4

9

8

7

6

See page 11 on “Configuring GSD Controller Communication” to setup the application
for serial communications