Grundig GCG2302E User Manual

COLOR TELEVISION
P 37-070

P 37-732/5 text

Connection Possibilities

ķ

2

Additional Information for Units sold in Great Britain

Units sold in GB are suitable for operation from a 240 V AC, 50 Hz mains
supply.

In case this appliance is supplied with a Safet

y Standard A

pproved mains lead
fitted with a non-rewireable 13 Amp mains plug which, if unsuitable for your
socket, should be cut off and an appropriate plug fitted by a qualified electrician.
The fuse and fuse holder must be removed from the plug as accidental insertion
of the redundant plug into a 13 Amp socket is likely to cause an electrical
hazard.

Note: The severed plug must be destroyed to avoid a possible shock hazard

should it be inserted into a 13 Amp socket elsewhere.

If it is necessary to change the fuse in the non-rewireable plug, the correct type
and rating (5 Amp ASTA or BSI approved BS 1362) must be used and the fuse
cover must be refitted. If the fuse cover is lost or damaged the lead and plug
must not be used until a replacement is obtained. Replacement fuse covers
should be obtained from your dealer.

If a non-rewireable plug or a rewireable 13 Amp (BS 1363) plug is used, it must
be fitted with a 5 Amp ASTA or BSI approved BS 1362 fuse. If any othe type of
plug is used it must be protected by a 5 Amp fuse either in the plug or at the
distribution board.

Important:
The wires in the mains lead are coloured in accordance with the following code:

BLUE – NEUTRAL
BROWN – LIVE

As the colours of the wires in the mains lead of your appliance may not
correspond with the coloured marking identifying the terminals in your plug,
proceed as follows:
Connect the BLUE coloured wire to plug terminal marked with the letter "N" or
coloured black.
Connect the BROWN coloured wire to the plug terminal marked with a letter "L"
or coloured red.
In no circumstance must any of the wires be connected to the terminal marked
with a letter "E", earth symbol , coloured green or green and yellow.

Replacement mains lead can be obtained from your dealer.

Safety and Installation

ķ

3

r

Safety instructions

Ń

!

If the unit is to be operated in a confined space, minimum spacings must be
observed (10 cm to each side, 20 cm at the top).

Ń

!

Ensure that the ventilation slits at the rear of the set are not covered up.
Heat build-up is a source of danger and infleuences the service life of the
set. Do not position the set close to heaters.

Ń

!

Make sure that the mains supply cable is not caught, trapped or damaged
when setting up the unit and when the machine is in operation.

Ń

!

Even when the machine is switched off, the set can be damaged by a
lightning stroke in the mains and/or aerial lead.
Therefore, you should always disconnect the mains and aerial plugs during
storms.

Ń

!

Protect the set from moisture.

Ń

!

Never insert anything into the ventilation slits at the rear of the unit.
Caution – high voltage!

r

Inserting the batteries into the remote control unit

Insert the supplied batteries, observing the polarity of the batteries (marked
on the bottom of the battery compartment).

Ń

!

If the batteries are used up, the following message appears on the screen:
»Batter.«.
Always remove used batteries.

We can accept no responsibility for damage caused by leaking batteries.
Dispose of the batteries in a enviromentally-safe way.

r

Connecting the unit and switching the set on and off

Insert the telescopic aerial supplied into the recess provided in the back
panel. Insert the aerial lead into the aerial socket É on the television.

Insert the mains lead into the socket.

Press the

¢

IO

button on the set.

Ń

!

If only the LED lights up afterwards, the set is on stand-by.
Switch on the set with the remote control by pressing one of the buttons

0/AV…9.

3

2

1

1