Grundig GCF3481E User Manual

COLOR TELEVISION

ST 55-800/9 text

Safety and Installation

Inserting the Battery into the Remote Control Handset

Insert the battery supplied. Make sure it is inserted correctly (markings in the battery compartment).

When the battery is dead, the message ” BATTERY” appears on the picture screen. Remove the dead battery immediately.

We assume no responsibility for damage resulting from battery leakage.

Dead batteries must be disposed of properly.

Connecting the TV Set

Insert the plug of the aerial lead into the aerial socket É of the TV set.

Insert the plug of the mains lead into a wall outlet.

Switching the TV Set On/Off

Press the

button on the unit.

The unit can be switched off from stand-by mode by pressing the

button on the remote control.

If you do not use the TV set for extended periods of time (e.g. at night), turn it off with this button.

This helps you to save energy.

The dialogue line as user’s guide

The line which is displayed at the bottom of the menus shows you which buttons on the remote control handset are to be used to change settings..

The

>, <,

ʺʺ, ɶɶ

signs on the picture screen are symbols for the following buttons on the remote control handset:

ʺʺ, ɶɶ

= P+ and P– buttons. Cursor movement

up/down for function selection.

<, > = ņ – and + ŀ buttons: Cursor move-

ment left/right for function selection.

In the following text, the buttons instead of the symbols will be shown.

Additional Information for Units sold in Great Britain

Units sold in GB are suitable for operation from a 240 V AC, 50 Hz mains supply. In case this appliance is supplied with a Safet

y Standard Approved mains lead fitted with a non-rewireable 13 Amp mains plug which, if unsuitable for your socket, should be cut off and an appropriate plug fitted by a qualified electrician. The fuse and fuse holder must be removed from the plug as accidental insertion of the redundant plug into a 13 Amp socket is likely to cause an electrical hazard.

Note: The severed plug must be destroyed to avoid a possible shock hazard

should it be inserted into a 13 Amp socket elsewhere.

If it is necessary to change the fuse in the non-rewireable plug, the correct type and rating (5 Amp ASTA or BSI approved BS 1362) must be used and the fuse cover must be refitted. If the fuse cover is lost or damaged the lead and plug must not be used until a replacement is obtained. Replacement fuse covers should be obtained from your dealer.

If a non-rewireable plug or a rewireable 13 Amp (BS 1363) plug is used, it must be fitted with a 5 Amp ASTA or BSI approved BS 1362 fuse. If any othe type of

plug is used it must be protected by a 5 Amp fuse either in the plug or at the distribution board.

Important: The wires in the mains lead are coloured in accordance with the follow-ing code:

BLUE – NEUTRAL BROWN – LIVE

As the colours of the wires in the mains lead of your appliance may not correspond with the coloured marking identifying the terminals in your plug, proceed as follows: Connect the BLUE coloured wire to plug terminal marked with the letter "N" or coloured black. Connect the BROWN coloured wire to the plug terminal marked with a letter "L" or coloured red. In no circumstance must any of the wires be connected to the terminal marked with a letter "E", earth symbol , coloured green or green and yellow.

Replacement mains lead can be obtained from your dealer.

When setting up your television, select a location where as little light as possible falls on the screen.

The ideal viewing distance is five times the diagonal width of the screen.

If the television is to be built into a compartment or similarly enclosed, minimum distances must be maintained.

Do not cover the ventilation openings on the back.

The heat exchange inside the unit generates an air circulation which attracts dust particles (carpet and curtain fibres and home dust). These particles accumulate inside the ventilation slots obstructing these over the years and causing a build-up of heat.

Heat build-up can reduce the service life of your television, and can also be dangerous.

For your own safety, let remove the dust deposits by a specialist from time to time.

Never set up speakers next to the unit.

When setting up and using this unit, please make sure that the mains connection wire is free and not jammed in order to avoid damage.

Never place the television near heat sources.

Even if your television is switched off, it can still be damaged by lightning striking the mains and/or aerial cables.

For this reason, you should always disconnect your television from the mains and the aerial system during electrical storms.

Never expose the unit to moisture.

Do not insert foreign objects into the ventilation openings on the back. Caution! High voltage!

20 cm

Programme Position Allocation

1st Possibility

The Automatic Tuning System ATS

This automatic tuning system scans the entire reception range and automatically stores the channels found in memory.

How to pr

oceed:

Switch the TV set on from standby with one of the buttons 1...9.

Press for approximately 4 seconds on the P/C but- ton to display the ATS menu.

If you should receive programmes in France, select FR ON.

If you receive french programmes outside France, select FR OFF L.

Press the + ŀ button once.

If you receive programmes in one of the countries of East or South-East Europa, select FR OFF DK.

Press the + ŀ button twice.

Press the

-button to start the search function.

The search can last longer than one minute. When it has stopped, setting of the TV set is completed.

If you do not like the order in which the programmes are stored on the programme positions, you can change this according to your preferences.

The search can be aborted using the ǺǺbutton.

Changing the Programme Order

Example: you wish to move the programme stored on position 2 to position 5.

Select programme position 2. Press the P/C button. The programme menu is dis-

played. Under ”PR”, enter the new programme position

number 05 as two digits with the buttons 1...9. Press the OK-button to terminate the adjustment. Press the

ǺǺ

button to return to TV mode.

2nd Possibility

Direct Channel Entry

For this, you need to know the channel numbers of the TV prgrammes.

If you have already assigned the programmes to the programme positons with the help of the ATS function, this procedure is not required.

How to

proceed:

Press the P/C-button to display the programme menu.

Attention – this is not possible in the AV position.

Press the

ņ – or + ŀ button to select the desired

item. Under ”PR” Press P+/P-to select the desired pro-

gramme position.

" "CH" Enter channel number, (for special

channel, press P+ or P- to select ”S” instead of ”C”).

Press the +

ŀ button. Use the numbe-

red buttons to enter the required channel number.

Hold down P+ or P- to start the channel search. This stops at each programme being received.

" "S" Select the telvision standard ”S”.

Press +

ŀ button.

Press P+ or P- to select the desired standard.

Press

ǺǺ

to exit the menü.

" "DEC" If an encrypted prgramme is allo-

cated to the programme position and a corresponding decoder connected, select ”ON”.

" "FT" If fine tuning should be necessary

after programme allocating, then press P+ or P- until the best picture

and sound quality is obtained.

Press OK to store the modified settings. The programme data of the next programme position is displayed.

Press

ǺǺ

to return to the television picture.

If the channel number 00 is entered with P+ or P- on one programme position, all following programme positions can no longer be selected.

PR CH S DEC FT 22 S06 0 ON 00

0-9

ɶɶʺʺ

ɼɦ OK i

Dialogue line

+ 6 hidden pages