Grundig GCE0492E User Manual
COLOR TELEVISION
SE 7277 text
Ń
!
When setting up your television, select a location
where as little light as possible falls on the screen.
Ń
!
The ideal viewing distance is five times the diagonal
width of the screen.
Ń
!
If the television is to be built into a compartment or
similarly enclosed, minimum distances must be
maintained.
Ń
!
Do not cover the ventilation openings on the back.
Ń
!
The heat exchange inside the unit generates an air
circulation which attracts dust particles (carpet and
curtain fibres and home dust). These particles
accumulate inside the ventilation slots obstructing
these over the years and causing a build-up of heat.
Heat build-up can reduce the service life of your
television, and can also be dangerous.
For your own safety, let remove the dust deposits
by a specialist from time to time.
Ń
!
Never set up speakers next to the unit.
Ń
!
When setting up and using this unit, please make
sure that the mains connection wire is free and not
jammed in order to avoid damage..
Ń
!
Never place the television near heat sources.
Ń
!
Even if your television is switched off, it can still be
damaged by lightning striking the mains and/or
aerial cables.
For this reason, you should always disconnect your
television from the mains and the aerial system
during electrical storms.
Ń
!
Never expose the unit to moisture.
Ń
!
Do not insert foreign objects into the ventilation
openings on the back.
Caution! High voltage!
Ń
!
The TV receiver is provided with a Megatron-picture
tube with a special surface layer.
This has the advantage of an antistatic effect, i.e.
the surface does not attract dust particles.
When the set is switched on, static charges of the
picture screen are avoided to a large degree by the
special surface layer.
Clean the picture screen of your TV set only with a
moistened soft cloth.
Use clear and clean water only.
When cleaning the picture screen, do not apply
pressure (abrasion, scratches).
Do not stick labels of any kind onto the picture
screen.
Inserting the Battery into the
Remote Control Handset
Insert the battery supplied. Make sure it is inserted
correctly (markings in the battery compartment).
Ń
!
When the battery is dead, the message
” BATTERY” appears on the picture screen.
Remove the dead battery immediately.
We assume no responsibility for damage resulting
from battery leakage.
Dead batteries must be disposed of properly.
Connecting the TV Set
Insert the plug of the aerial lead into the aerial
socket É of the TV set.
Insert the plug of the mains lead into a wall outlet.
Switching the set on/off
Press the
¢
IO
button on the set.
Switch to standby: press the
b button on the
remote control handset.
Switch off with the remote control handset: press
the
b button twice.
The set is equipped with a save-energy switch
which switches definitely off from standby after half
an hour.
Switch the set on again: press the
¢
IO
button on the
set.
Ń
!
Approximately ten minutes after the last broadcast
or in the case of a broadcasting failure (if there is
no test pattern), the set switches automatically to
standby. The save-energy switch is activated.
Ń
!
Your specialized dealer can deactivate the saveenergy switch.
The dialogue line as user’s guide
Ń
!
The line which is displayed at the bottom of the
menus shows you which buttons on the remote
control handset are to be used to change settings..
The
>, <,
ʺʺ, ɶɶ
signs on the picture screen are
symbols for the following buttons on the remote
control handset:
ʺʺ, ɶɶ
= ]and |buttons. Cursor movement
up/down for function selection.
<, > =
x
and cbuttons: Cursor movement
left/right for function selection.
In the following text, the buttons instead of the
symbols will be shown.
3
2
1
2
1
1
ķ
9
Safety and Installation
10
cm
20
cm
20 cm
10
cm
1st Possibility
r
The Automatic Tuning System ATS
This automatic tuning system scans the entire
reception range and automatically stores the
channels found in memory.
How to proceed:
Switch the TV set on from standby with one of the
buttons
1…9
.
Pull back the slider on the remote control handset.
Press for approximately 4 seconds on the E button to display the ATS menu.
Press the
O
button to start the search function.
The search can last longer than one minute. When it
has stopped, setting of the TV set is completed.
If you do not like the order in which the programmes are stored on the programme positions, you
can change this according to your preferences.
Ń
!
The search function can be stopped by pressing
.
.
r
Changing the Programme Order
Example: you wish to move the programme stored
on position 2 to position 5.
Select programme position 2.
Press the E button. The programme menu is displayed.
Under ”PR”, enter the new programme position
number 05 as two digits with the buttons
0…9
.
Press the
“
OK
button to terminate the adjustment.
Press the
.
button to return to TV mode.
5
4
3
2
1
4
3
2
1
2nd Possibility
r
Direct Channel Entry
For this, you need to know the channel numbers of
the TV prgrammes.
Ń
!
If you have already assigned the programmes to the
programme positons with the help of the ATS function, this procedure is not required.
How to
proceed:
Press the E button to display the programme
menu.
Ń
!
Attention – this is not possible in the AV position.
Press the
x
or cbutton to select the desired
item.
Under ”PR” press ]/|to select the desired
programme position.
" "CH" enter channel number, (for special
channel, press ]to select ”S”
instead of ”C”.).
Hold down ]or |to start the
channel search. This stops at each
programme being received.
" "DEC" If an encrypted prgramme is allo-
cated to the programme position and
a corresponding decoder connected,
select ”ON”.
" "FT" If fine tuning should be necessary
after programme allocating, then
press ]or |until the best picture
and sound quality is obtained.
Press
“
OK
to store the modified settings.
The programme data of the next programme position is displayed.
Press
.
to return to the television picture.
Ń
!
If the channel number 00 is entered with ]or
|
on one programme position, all following programme positions can no longer be selected.
4
3
2
PR CH DEC FT
22 S06 ON 00
0…9
ɶɶʺʺ
ɼɦ OK i
1
ķ
10
Programme Position Allocation
ĵ
Dialogue line
Loading...