Grundig GCD9778E User Manual

COLOR TELEVISION
T 51-720 text/GB
V
Contents
Contents
Contens and Warning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Connection and Operation on the Set . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
Teletext Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-12
Connection Possibilties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-14
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Ń
!
Warning
In case this appliance is supplied with a Safety Standard Approved mains lead fitted with a non-rewireable 13 Amp mains plug which, if unsuitable for your socket, should be cut off and an appropriate plug fitted by a qualified electrician. The fuse and fuse holder must be removed from the plug as accidental insertion of the redundant plug into a 13 Amp socket is likely to cause an electrical hazard.
Note:The severed plug must be destroyed to avoid a possible shock hazard
should it be inserted into a 13 Amp socket elsewhere.
If it is necessary to change the fuse in the non-rewireable plug, the correct type and rating (5 Amp ASTA or BSI approved BS 1362) must be used and the fuse cover must be refitted. If the fuse cover is lost or damaged the lead and plug must not be used until a replacement is obtained. Replacement fuse covers should be obtained from your dealer.
If a non-rewireable plug or a rewireable 13 Amp (BS 1363) plug is used, it must be fitted with a 5 Amp ASTA or BSI approved BS 1362 fuse. If any other type of plug is used it must be protected by a 5 Amp fuse either in the plug or at the distribution board.
ķ
2
Important: The wires in the mains lead are coloured in accordance with the following code: BLUE – NEUTRAL BROWN – LIVE As the colours of the wires in the mains lead of your appliance may not correspond with the
coloured marking identifying the terminals in your plug, proceed as follows: Connect the BLUE coloured wire to plug terminal marked with the letter "N" or coloured
black. Connect the BROWN coloured wire to the plug terminal marked with a letter "L" or coloured red. In no circumstance must any of the wires be connected to the terminal marked with a letter
"E", earth symbol , coloured green or green and yellow. Replacement mains lead can be obtained from your dealer.
Set-up, Safety and Preparation
ķ
3
Set-up and Safety
Ń
!
The minimum spacings – 10 cm on each side and 20 cm at the top – must be observed for operation in a wall unit.
Do not cover the ventilation openings on the rear panel. Heat accumulation poses a risk and is detrimental to the service life of the equipment.
Do not place the set near to heating appliances.
Ń
!
The mains cable must not be clamped or damaged. Even if the set is switched off, it could be damaged by a lightning strike
hitting the mains and/or the aerial lead. Therefore, always disconnect the mains plug and aerial plug when storms
are apparent. Protect the set from moisture and dripping or splashing water. Do not insert any objects into the ventilation openings.
Caution high voltage!
Inserting the Batteries in the Remote Control
Insert the batteries supplied observing the polarity (marked on base of battery compartment).
»Batter.« will appear on the set screen when the battery is flat. Ensure that used batteries are removed and disposed of in an environ­mentally friendly way. There is no liability for damage occuring through dead batteries.
Ǻ
Connection and Operation on the Set
ķ
4
Connection
Connect the aerial cable to the aerial socket É on the set. Connect the mains cable plug to the set mains socket and to the wall
socket. Connection of external equipment is described on pages 13 and 14.
Operation on the Set
Switching on/off
Press the übutton. – If the display then illuminates, the set is in standby mode.
Switch the set on completely with the P +button.
Selecting channels
Select the channels with the
P
+
buttons.
P
Ǻ
2
1
AV
Settings
ķ
5
Assigning Channel Positions with the ATS Automatic Channel Search and Memory System
There are 69 channel positions available which can be assigned television channels from the aerial or from the cable connection as desired.
The set is equipped with an automatic channel search system, A TS. You start the search and can then sort the television channels into an order
of your choice. You can also delete television channels which were found several times or
which have poor reception from the channel list. »ATS« is displayed when the set is switched on.
If »ATS« is not displayed, press the
AUX
button for approx. 4 seconds until
the display appears.
Start the search with the G button. – The search procedure can take over a minute.
The search can be aborted with the h button. Once the set has stored all television channels it will switch to channel
position 1.
Deleting Television Channels
You can delete television channels with poor reception. Press the h and then the G button.
– The »Channel Display« will appear. Select the channel position whose television channel should be deleted with
the p or P button. Delete the television channel by pressing the
TXT
and then the G button.
– The subsequent television channels will move by one channel position to
the front.
End the setting with the h button.
4
3
2
1
Ǻ
Ǻ
2
Ǻ
1
ATS
OK
i
Loading...
+ 11 hidden pages