Groupe SEB PE177C User Manual

AI RB AK E A LL -C L AD A RN O AS I AV IN A CA L OR C LO C K IM US A KR UP S L AG OS T IN A MA HA RA JA WH IT EL I NE M IR RO MO UL IN E X PA NE X P EN ED O RE G AL R OC HE DO RO WE NT A S AM UR AI S EB SU PO R TE F AL T - FA L U MC O WE A RE VE R
DE / From : Karim HOUNI DATE : 21/04/2016
Technology Department
OBJET / SUBJECT PE177-C Bluetooth LE Serial Dongle Regulatory Compliance Information,
to be added to product manual and guarantee documents
Regulatory Compliance Information FCC Requirements :
§ 15.19 Labeling requirements
o This device complies with Part 15 of the FCC Rules and Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
o Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
§ 15.21 Information to user.
o Changes or modifications not expressly approved by the party responsible for compliance could void the
user's authority to operate the equipment.
§ 15.105 Information to user.
o This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on, the user is encouraged to try to correct interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
§ RF Exposure.
o This device complies with FCC and Industry Canada RF radiation exposure limits set forth for general
population. This device must not be co-located or operating in conjunction with any other antenna or transmitter.
o Le présent appareil est conforme aux niveaux limites d’exigences d’exposition RF pour la population
globale définies par FCC et Industrie Canada. L’appareil ne doit pas être installé à proximité ou être
utilisé en conjonction avec une autre antenne ou un autre émetteur.
IC Requirements :
§ 7.1.2 RSS Gen / Transmitter Antenna.
o Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and
maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.
o Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une
antenne d'un type et d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante.
Page 1 / 1
Loading...