Grizzly Industrial G0544, G5850Z, G5851Z, G7213Z User guide

READ THIS FIRST

G5851Z 24''

Variable Speed Planer

Models G0544/G5850Z/

G5851Z/G7213Z

***IMPORTANT UPDATE***

For Machines Mfd. Since 12/16

and Owner's Manual Revised 03/06

For questions or help with this product contact Tech Support at [phone] or [e-mail]

The following changes were recently made to this machine since the owner's manual was printed:

• Updated electrical component information and parts list.

• Updated wiring diagram.

• Updated belt size.

Aside from this information, all other content in the owner's manual applies and MUST be read and under­stood for your own safety. IMPORTANT: Keep this update with the owner's manual for future reference.

For questions or help, contact our Tech Support at [phone] or [e-mail].

Revised G0544, G5850Z & G5851Z Breakdown & Parts List

301

128

302

REF PART # DESCRIPTION REF PART # DESCRIPTION

128 P5851Z128 BELT A64 300V2-4 P5850Z300V2-4 OL RELAY RIKEN BTH-352H3624-36A
300V2 P5850Z300V2 MAG SWITCH ASSY V2.12.16 301 P5850Z301 FUSE HOLDER
300V2-1 P5850Z300V2-1 CONTACTOR RIKEN RAB-A18 220V 301-1 P5850Z301-1 FUSE 2A
300V2-2 P5850Z300V2-2 OL RELAY RIKEN BTH-18T-2H18 12-18A 302 P5850Z180 INDICATOR LIGHT (220V)
300V2-3 P5850Z300V2-3 CONTACTOR RIEKN RAB-A35 220V

301-1

300V2

300V2-1

300V2-3

(Upper)

300V2-2

(Lower)

300V2-4

COPYRIGHT © MARCH, 2017 BY GRIZZLY INDUSTRIAL, INC.

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#JH14254 PRINTED IN TAIWAN

V1.07.17

Revised G7213Z Breakdown & Parts List

G5851Z 24''

Variable Speed Planer

440V Conversion Kit

302-1

(Upper)

302-3

302-2

302-5

302-6
302-7

(Lower)

128

302-4

302

303

301-1

301

300V2

300V2-1

300V2-3

(Upper)

300V2-2

(Lower)

300V2-4

REF PART # DESCRIPTION REF PART # DESCRIPTION

128 P7213Z128 BELT A64 302-1 P7213Z302-1 CONTACTOR RIKEN RAB-A12 440V
300V2 P7213Z300V2 MAGNETIC SWITCH ASSY 3-PH V2.12.16 302-2 P7213Z302-2 OL RELAY RIKEN BTH-18T2H4.3 2.9-4.3A
300V2-1 P7213Z300V2-1 CONTACTOR RIKEN RAB-A12 220V V2.12.16 302-3 P7213Z302-3 CONTACTOR RIKEN RAB-A18 440V
300V2-2 P7213Z300V2-2 OL RELAY RIKEN BTH-18T 2H8 5.4-8A V2.12.16 302-4 P7213Z302-4 OL RELAY RIKEN BTH-18T2H18 12-18A
300V2-3 P7213Z300V2-3 CONTACTOR RIKEN RAB-A30 220V V2.12.16 302-5 P7213Z302-5 POWER FEED BULB (440V)
300V2-4 P7213Z300V2-4 OL RELAY RIKEN BTH-35 2H26 18-26A V2.12.16 302-6 P7213Z302-6 MAIN MOTOR BULB (440V)
301 P7213Z301 FUSE 2A 302-7 P7213Z302-7 FEED MOTOR BULB (440V)
301-1 P7213Z301-1 FUSE HOLDER 303 P7213Z303 INDICATOR BULB (220V)
302 P7213Z302 440V CONVERSION KIT

-2-

G0544–G7213Z Update (Mfd. Since 12/16)

Revised G0544, G5850Z & G5851Z Wiring

0

R

0

4

T

T/5/L3S/3/L2R/1/L1

RAB­A18

220V

U/2/T1 V/4/T2 W/6/T3 14NO

Riken

13NO

13NO
21NC
22NC
14NO

Diagram

Single-Phase

220V Power Source

3

3

R

FUSE 2A

1

Power Indicator

0

0

1

2

2

R

T

E

E

S

S

E

E

T

R

1

1

0 0

RAB­A35

220V

U/2/T1 V/4/T2 W/6/T3 14NO

Riken

3

2

T/5/L3S/3/L2R/1/L1

13NO

13NO
21NC
22NC
14NO

BTH-18T-2H18

1L1
2T1

Feed

Motor

3L2
4T2

5L3
6T3

Start

Capacitor

300MFD
250VAC

12 15 18

5

3

1

T

GND

4

4

5L3
6T3

GND

24 30 36

5

Capacitor

400MFD

250VAC

Start

BTH-35-2H36P

T

E

T

R

U

H

C

E

T

A

D

R

A

S

T

2

0
0

E

E

F

T

4

4

2

3

3

D

S

T

A

R

3

0

Ground

1L1
2T1

Start

Capacitor

400MFD
250VAC

3L2
4T2

3

2 1

3

3

0

Main

Motor

G0544–G7213Z Update (Mfd. Since 12/16)

-3-

Revised G7213Z 220V Wiring Diagram

Single-Phase

220V Power Source

0

R

0

4

13NO

21NC

3

3

R

Power Indicator

0

0

1

1

0 0

T

T/5/L3S/3/L2R/1/L1

3

2

13NO

T/5/L3S/3/L2R/1/L1

21NC

RAB-

A12-10

220V

U/2/T1 V/4/T2 W/6/T3

Feed

Motor

BTH-18T2H8

1L1

3L2

2T1

4T2

Riken

5L3
6T3

5.4 6.7 8.0

5

3 5

22NC

14NO

4

FUSE 2A

1

4

4

T

GND

1

2

6

2

2

R

T

E

S

E

R

T

E

T

U

C

T

R

A

S

T

2

0
0

E

E

F

T

R

4

4

1

E

S

E

T

R

H

E

A

D

3

3

D

S

T

A

3

0

Ground

RAB­A30

220V

U/2/T1 V/4/T2 W/6/T3

GND

BTH-35T2H26

1L1

3L2

2T1

4T2

3

Riken

5L3
6T3

5 4

2

18 22 26

5

1

6

22NC

14NO

3

3

0

Main

Motor

-4-

G0544–G7213Z Update (Mfd. Since 12/16)

Revised G7213Z 440V Wiring Diagram

Single-Phase

440V Power Source

Indicates changes
from 220V to 440V

0

0

R

4

13NO

21NC

3

3

R

Power Indicator

0

0

1

1

0 0

T/5/L3S/3/L2R/1/L1

T

T/5/L3S/3/L2R/1/L1

3

21NC

2

13NO

RAB-

A12-10

440V

U/2/T1

BTH-18T2H4.3

1L1
2T1

Feed

Motor

Riken

V/4/T2 W/6/T3

3L2

5L3

4T2

6T3

3

2.9 3.6 4.3

5

2

22NC

14NO

1

FUSE 2A

1

4

4

T

4

5

GND

6

2

2

R

T

E

S

E

R

T

E

T

U

C

T

R

A

S

T

2

0
0

E

E

F

T

R

4

4

1

E

S

E

T

R

H

E

A

D

3

3

D

S

T

A

3

0

Ground

RAB­A18

440V

U/2/T1 V/4/T2 W/6/T3

GND

BTH-18T2H18

1L1

3L2

2T1

4T2

3

Riken

5L3
6T3

5

2

1

12 15 18

5

4

6

22NC

14NO

3

3

0

Main

Motor

G0544–G7213Z Update (Mfd. Since 12/16)

-5-

PROFESSIONAL SERIES

PLANERS

MODELS G5850Z/G5851Z/G7213Z/G0544

INSTRUCTION MANUAL

COPYRIGHT © MAY, 2002 BY GRIZZLY INDUSTRIAL, INC. REVISED SEPTEMBER, 2005

WARNING : NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#TR4135 PRINTED IN TAIWAN REVISED MARCH, 2006 (JK)

V1.01.16

This manual provides critical safety instructions on the proper setup,
operation, maintenance, and service of this machine/tool. Save this
document, refer to it often, and use it to instruct other operators.

Failure to read, understand and follow the instructions in this manual
may result in fire or serious personal injury—including amputation,
electrocution, or death.

The owner of this machine/tool is solely responsible for its safe use.
This responsibility includes but is not limited to proper installation in
a safe environment, personnel training and usage authorization,
proper inspection and maintenance, manual availability and compre­hension, application of safety devices, cutting/sanding/grinding tool
integrity, and the usage of personal protective equipment.

The manufacturer will not be held liable for injury or property damage
from negligence, improper training, machine modifications or misuse.

Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to the State
of California to cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:

• Lead from lead-based paints.

• Crystalline silica from bricks, cement and other masonry products.

• Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals:
Work in a well ventilated area, and work with approved safety equip­ment, such as those dust masks that are specially designed to filter
out microscopic particles.

Table Of Contents

PAGE

1. SAFETY

SAFETY RULES FOR ALL TOOLS ...................................................................................2-3

ADDITIONAL SAFETY INSTRUCTIONS FOR PLANERS ...................................................4

2. CIRCUIT REQUIREMENTS .........................................................................................................5

220V SINGLE-PHASE ...........................................................................................................5

220V 3-PHASE ...................................................................................................................... 5

GROUNDING ........................................................................................................................6

EXTENSION CORDS ............................................................................................................ 6

3. GENERAL INFORMATION .........................................................................................................7

COMMENTARY .....................................................................................................................7

UNPACKING .........................................................................................................................8

PIECE INVENTORY .............................................................................................................. 8

HARDWARE RECOGNITION CHART ..................................................................................9

CLEAN UP ...........................................................................................................................10

SITE CONSIDERATIONS ...................................................................................................10

4. ASSEMBLY ...............................................................................................................................11

BEGINNING ASSEMBLY .................................................................................................... 11

DUST HOOD ....................................................................................................................... 11

ADJUSTMENT HANDLE ..................................................................................................... 11

5. ADJUSTMENTS ........................................................................................................................12

ADJUSTMENT CONTROLS ...............................................................................................12

CUTTERHEAD KNIVES .................................................................................................13-14

TABLE ............................................................................................................................15-17

FEED ROLLERS, PRESSURE BAR & CHIP BREAKER ..............................................18-19

TABLE ROLLERS ...............................................................................................................20

FEED ROLLER TENSION................................................................................................... 21

TEST RUN ...........................................................................................................................21

6. OPERATION .............................................................................................................................. 22

OPERATION CONTROLS ..................................................................................................22

FEED RATE ........................................................................................................................23

OPERATIONAL TIPS .......................................................................................................... 23

WOOD CHARACTERISTICS .............................................................................................. 24

7. MAINTENANCE .........................................................................................................................25

GENERAL............................................................................................................................25

CLEANING ..........................................................................................................................25

TABLE .................................................................................................................................25

LUBRICATION................................................................................................................25-26

V-BELT ................................................................................................................................ 26

INDEXABLE INSERTS (G0544).......................................................................................... 27

G5850Z/G5851Z/G0544 WIRING DIAGRAM...................................................................... 28

G7213Z WIRING DIAGRAM ...............................................................................................29

8. CLOSURE ..................................................................................................................................30

G5850Z/G0544 MACHINE DATA........................................................................................ 31

G5850Z/G0544 PARTS BREAKDOWN AND PARTS LIST ...........................................32-37

G5851Z MACHINE DATA ...................................................................................................38

G7213Z MACHINE DATA ...................................................................................................39

G5851Z/G7213Z PARTS BREAKDOWN AND PARTS LIST ........................................40-45

WARRANTY AND RETURNS ............................................................................................. 46

SECTION 1: SAFETY

For Your Own Safety, Read Instruction

Manual Before Operating this Power Tool

The purpose of safety symbols is to attract your attention to possible hazardous conditions.
This manual uses a series of symbols and signal words intended to convey the level of impor­tance of the safety messages. The progression of symbols is described below. Remember that
safety messages by themselves do not eliminate danger and are not a substitute for proper
accident prevention measures. Always use common sense and good judgment.

Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury. It may also be used to alert
against unsafe practices.

This symbol is used to alert the user to useful information about

NOTICE

proper operation of the machine.

OWNER’S MANUAL. Read and understand this

owner’s manual BEFORE using machine.

TRAINED OPERATORS ONLY. Untrained oper­ators have a higher risk of being hurt or killed.
Only allow trained/supervised people to use this
power tool. When tool is not being used, discon­nect power, and store in out-of-reach location
to prevent unauthorized use—especially around
children. Make workshop kid proof!

DANGEROUS ENVIRONMENTS. Do not use
tools in areas that are wet, cluttered, or have poor
lighting. Operating tools in these areas greatly
increases risk of accidents and injury.

MENTAL ALERTNESS REQUIRED. Full mental
alertness is required for safe operation of power
tools. Never operate under the influence of drugs
or alcohol, when tired, or when distracted.

-2-

DISCONNECT POWER FIRST.
tool from power supply BEFORE making adjust­ments, changing tooling, or servicing machine. This
prevents an injury risk from unintended startup or
contact with live electrical components.

EYE PROTECTION. Always wear ANSI-approved
safety glasses or a face shield when operating or
observing machinery to reduce the risk of eye
injury or blindness from flying particles. Everyday
eyeglasses are not approved safety glasses.

ELECTRICAL SAFETY. Tool plug must match
outlet. Double-insulated tools have a polarized
plug (one blade is wider than the other), which
must be plugged into a polarized outlet. Never
modify plug. Do not use adapter for grounded
tools. Use a ground fault circuit interrupter if
operation is unavoidable in damp locations. Avoid
touching grounded surfaces when operating tool.

Always disconnect

WEARING PROPER APPAREL. Do not wear
clothing, apparel or jewelry that can become
entangled in moving parts. Always tie back or
cover long hair. Wear non-slip footwear to avoid
accidental slips, which could cause loss of work­piece control. Wear hard hat as needed.

HAZARDOUS DUST. Dust created while using
tools may cause cancer, birth defects, or long­term respiratory damage. Be aware of dust haz­ards associated with each workpiece material,
always wear a NIOSH-approved respirator, and
connect tool to an appropriate dust collection
device to reduce your risk.

HEARING PROTECTION. Always wear hear­ing protection when operating or observing loud
machinery. Extended exposure to this noise
without hearing protection can cause permanent
hearing loss.

REMOVE ADJUSTING TOOLS. Never leave
adjustment tools, chuck keys, wrenches, etc. in
or on tool—especially near moving parts. Verify
removal before starting!

INTENDED USAGE. Only use tool for its intended
purpose. Never modify or alter tool for a purpose
not intended by the manufacturer or serious injury
or death may result!

AWKWARD POSITIONS. Keep proper footing
and balance at all times when operating tool. Do
not overreach! Avoid awkward hand positions that
make tool control difficult or increase the risk of
accidental injury.

CHILDREN & BYSTANDERS. Keep children and
bystanders at a safe distance from the work area.
Stop using machine if they become a distraction.

FORCING TOOLS. Use the right tool for the job,
and do not force it. It will do the job safer and bet­ter at the rate for which it was designed.

USE RECOMMENDED ACCESSORIES. Consult
this owner’s manual or the manufacturer for rec­ommended accessories. Using improper acces­sories will increase the risk of serious injury.

MAINTAIN WITH CARE. Keep cutting tool edges
sharp and clean. Follow all maintenance instruc­tions and lubrication schedules to keep tool in
good working condition. A tool that is improperly
maintained could malfunction, leading to serious
personal injury or death. Only have tool serviced
by qualified service-personnel using matching
replacement parts.

CHECK DAMAGED PARTS. Regularly inspect
tool for any condition that may affect safe opera­tion. Immediately repair or replace damaged or
mis-adjusted parts before operating tool.

MAINTAIN POWER CORDS. When disconnect­ing cord-connected tools from power, grab and
pull the plug—NOT the cord. Carrying or pulling
the cord may damage wires inside. Do not handle
cord/plug with wet hands. Avoid cord damage by
keeping it away from heated surfaces, high traf­fic areas, harsh chemicals, sharp edges, moving
parts, and wet/damp locations. Damaged cords
increase risk of electrocution.

SAFE HANDLING. Firmly grip tool. To avoid
accidental firing, do not keep finger on switch or
trigger while carrying.

SECURING WORKPIECE. When required, use
clamps or vises to secure workpiece. A secured
workpiece protects hands and frees both of them
to operate the tool.

GUARDS & COVERS. Guards and covers reduce
accidental contact with moving parts or flying
debris. Make sure they are properly installed,
undamaged, and working correctly.

UNATT E N DED OPERATION . Never leave tool
running while unattended. Turn tool off and ensure
all moving parts completely stop before walking
away.

EXPERIENCING DIFFICULTIES. If at any time
you experience difficulties performing the intend­ed operation, stop using the machine! Contact our
Technical Support at [phone].

-3-

Wood chips fly

Additional Safety Instructions for Planers

Amputation, serious cuts, entanglement, or death can occur from contact with rotating
cutterhead or other moving parts! Flying chips can cause blindness or eye injuries. Workpieces
or knives thrown by cutterhead can strike nearby operator or bystanders with deadly force. To
reduce the risk of these hazards, operator and bystanders MUST completely heed hazards and
warnings below.

KICKBACK. Know how to reduce the risk of kick-

back and kickback-related injuries. “Kickback”
occurs during the operation when the workpiece is
ejected from the machine at a high rate of speed.
Kickback is commonly caused by poor workpiece
selection, unsafe feeding techniques, or improper
machine setup/maintenance. Kickback injuries
typically occur as follows: (1) operator/bystanders
are struck by the workpiece, resulting in impact
injuries (i.e., blindness, broken bones, bruises,
death); (2) operator’s hands are pulled into blade,
resulting in amputation or severe lacerations.

AVOID CONTACT WITH MOVING PARTS. Never
remove guards/covers or reach inside the planer
during operation or while connected to power.
You could be seriously injured if you accidentally
touch the spinning cutterhead or get entangled in
moving parts. If a workpiece becomes stuck or
sawdust removal is necessary, turn planer OFF
and disconnect power before clearing.

DULL/DAMAGED KNIVES/INSERTS. Only use
sharp, undamaged knives/inserts. Dull or dam­aged knives/inserts increase the risk of kickback.

INSPECTING STOCK. To reduce the risk of
kickback injuries or machine damage, thoroughly
inspect and prepare the workpiece before cutting.
Verify workpiece is free of nails, staples, loose
knots or foreign material. Workpieces with minor
warping should be jointed first or planed with the
cupped side facing the table.

PLANING CORRECT MATERIAL. Only plane
natural wood stock with this planer. DO NOT
plane MDF, OSB, plywood, laminates or other
synthetic materials that can break up inside the
planer and be ejected towards the operator.

LOOKING INSIDE PLANER.

around inside the planer at a high rate of speed
during operation. To avoid injury from flying mate­rial, DO NOT look inside planer during operation.

CUTTING LIMITATIONS. To reduce the risk of
kickback hazards or damage to the machine, do
not exceed the maximum depth of cut or minimum
board length and thickness found in the Data

Sheet. Only feed one board at a time.

INFEED ROLLER CLEARANCE. The infeed

roller is designed to pull material into the spinning
cutterhead. To reduce the risk of entanglement,
keep hands, clothing, jewelry, and long hair away
from the infeed roller during operation.

FEED WORKPIECE PROPERLY. To reduce the
risk of kickback, never start planer with workpiece
touching cutterhead. Allow cutterhead to reach
full speed before feeding, and do not change feed
speed during cutting operation.

WORKPIECE SUPPORT. To reduce the risk of
kickback, always make sure workpiece can move
completely across table without rocking or tipping.
Use auxiliary support stands for long stock.

BODY PLACEMENT. Stand to one side of planer
during the entire operation to avoid getting hit if
kickback occurs.

GRAIN DIRECTION. Planing across the grain
is hard on the planer and may cause kickback.
Plane in the same direction or at a slight angle
with the wood grain.

-4-

SECURE KNIVES/INSERTS. Loose knives or
improperly set inserts can become dangerous
projectiles or cause machine damage. Always
verify knives/inserts are secure and properly
adjusted before operation.

SECTION 2: CIRCUIT REQUIREMENTS

220V Single-Phase

The Model G5850Z/G5851Z/G0544 is prewired
with a 5 HP single-phase motor. Under normal
use, this motor draws approximately 28 amps at
220V. We recommend using a 40 amp circuit.
This includes the appropriate wiring and circuit
breaker. If frequent circuit failure occurs when
using the planer, contact our service depart­ment.

The planer must be connected to its own dedi­cated 40A circuit. It should not share a circuit with
any other machine. A standard 2-pole breaker is
necessary for use with the planer.

We recommend using a NEMA-style L6-50 plug
and outlet similar to that in Figure 1. You
may also “hard-wire” the planer directly to your
panel, provided you place a disconnect near the
machine. Check the electrical codes in your area
for specifics on wiring requirements.

220V 3-Phase

The Model G7213Z Planer is prewired with a 71⁄2
HP 3-phase motor. Under normal use, the motor
draws approximately 22 amps at 220V. We rec­ommend using a 25 amp circuit. This includes the
appropriate wiring and circuit breaker. If frequent
circuit failure occurs when using the planer, con­tact our service department.

The planer must be connected to its own dedi­cated 25A circuit. It should not share a circuit with
any other machine. A standard 3-pole breaker is
necessary for use with 3-phase power.

We recommend using a NEMA-style L15-30
plug and outlet similar to that in Figure 2. You
may also “hard-wire” the planer directly to your
panel, provided you place a disconnect near the
machine. Check the electrical codes in your area
for specifics on wiring requirements.

Figure 1. Typical plug configuration for 220V,

single-phase operation.

Professional Series Planers

Figure 2. Typical plug configuration for 220V, 3-

phase operation.

-5-

Grounding

Extension Cords

In the event of an electrical short, grounding
reduces the risk of electric shock by providing
a path of least resistance to disperse electric
current. This tool is equipped with an electric
cord that has an equipment-grounding conductor
which must be properly connected to a grounding
plug. The plug must be plugged into a matching
outlet that is properly installed and grounded in
accordance with all local codes and ordinances.

Improper connections of the electrical-grounding
conductor can result in the risk of electric shock.
The conductor with green or green and yellow
striped insulation is the electrical-grounding con­ductor. If repair or replacement of the electric cord
or plug is necessary, do not connect the equip­ment grounding conductor to a live terminal.

This equipment must be
grounded. Verify that any
existing electrical out­let and circuit you intend
to plug into is actually
grounded. Under no cir­cumstances should the
grounding pin from any
three-pronged plug be
removed. Serious injury
may occur.

We do not recommend the use of extension
cords on 220V equipment. It is much better to
arrange the placement of your equipment and
the installed wiring to eliminate the need for
extension cords. Should it be necessary to use
an extension make sure the cord is rated Hard
Service (grade S) or better. Refer to the chart
in Section 1: Safety to determine the minimum
gauge for the extension cord. The extension cord
must also contain a ground wire and plug pin.
Always repair or replace extension cords when
they become worn or damaged.

-6-

-6-

Professional Series Planers

SECTION 3: GENERAL INFORMATION

Most important, we stand behind our machines.

Commentary

Grizzly Industrial, Inc. is proud to offer the
Professional Series Planers. These planers are
part of Grizzly’s growing family of fine woodwork­ing and metalworking machinery. When used
according to the guidelines stated in this manual,
you can expect years of trouble-free, enjoyable
operation.

The Models G0544, G5850Z, G5851Z & G7213
Professional Series Planers are the same machine
with the exception of motor size, electrical phase
and cutterhead differences. Please refer to the
chart below to distinguish planer differences.

These planers are intended for heavy-duty pro­fessional use and are capable of operating at
5200 RPM with a 17-26 FPM variable feed rate.

We are also pleased to provide this manual with
the Models G0444, G5850Z, G5851Z & G7213
Professional Series Planers. It was written to
guide you through assembly, review safety con­siderations, and cover general operating proce­dures. If you have any criticisms that you feel we
should address in our next printing, please write
to us at the address below:

Grizzly Industrial, Inc.

C

⁄O Technical Documentation

P.O. Box 2069

Bellingham, WA 98227

We have an excellent Service Department at your
disposal should the need arise. If you have any
service questions or parts requests, please call or
write to us at the location listed below.

Grizzly Industrial, Inc.

1203 Lycoming Mall Circle

Muncy, PA 17756

Phone:[phone]

Fax:[phone]
E-Mail: [e-mail]
Web Site: http://www.grizzly.com

The specifications, drawings, and photographs
illustrated in this manual represent the Professional
Series Planers as supplied when the manual was
prepared. However, owing to Grizzly’s policy
of continuous improvement, changes may be
made at any time with no obligation on the part
of Grizzly. Whenever possible, though, we send
manual updates to all owners of a particular tool
or machine. Should you receive one, we urge
you to insert the new information with the old and
keep it for reference.

Read the manual before
assembly and operation.
Become familiar with the
machine and its opera­tion before beginning
any work. Serious per­sonal injury may result
if safety or operational
information is not under­stood or followed.

Description G0544 G5850Z G5851Z G7213Z

Motor 5 HP 5 HP 5 HP 71/2 HP
Phase 1-Phase 1-Phase 1-Phase 3-Phase
Size 20" 20" 24" 24"
Cutterhead Spiral Cutterhead w/

Indexable Inserts

Professional Series Planers

4-Knife 4-Knife 4-Knife

-7-

Unpacking

Piece Inventory

The planer base unit and the hardware are
shipped from the manufacturer in a carefully
packed carton. If you discover the machine is
damaged after you have signed for delivery, and
the truck and driver are gone, you will need to file
a freight claim with the carrier. Save the contain­ers and all packing materials for possible inspec­tion by the carrier or its agent. Without the pack­ing materials, filing a freight claim can be difficult.

If you need assistance determining whether you
need to file a freight claim, or with the procedure
to file one, please contact our Customer Service.

These planers are heavy
machines—1030 lbs. ship­ping weight. DO NOT
over-exert yourself while
unpacking or moving
your machine. Use power
equipment. Serious per­sonal injury may occur if
safe moving methods are
not followed.

After all the parts have been removed from the
carton, you should have:

Part Qty

• Planer Unit 1

• Dust Hood 1

• Adjustment Handle 1

• Combo Wrench 10/12mm 1

• Combo Wrench 12/14mm 1

• Combo Wrench 17/19mm 1

• Hex Wrench 4mm 1

• Knife Setting Jig 1

In the event that any nonproprietary parts are
missing (e.g. a nut or a washer), we would be
glad to replace them, or for the sake of expedi­ency, replacements can be obtained at your local
hardware store.

When you are completely satisfied with the con­dition of your shipment, you should inventory its
parts.

Figure 3. Loose Parts.

-8-

Professional Series Planers

Hardware Recognition Chart

Use this chart to match up
hardware pieces during the
assembly process!

Professional Series Planers

-9-

Clean Up

Site Considerations

The unpainted surfaces are coated with a waxy
oil to protect them from corrosion during ship­ment. Remove this protective coating with a sol­vent cleaner or citrus-based degreaser such as
Grizzly’s G7895 Degreaser. To clean thoroughly,
some parts may need to be removed. For opti-

mum performance from your machine, make
sure you clean all moving parts or sliding
contact surfaces that are coated. Avoid chlo-

rine-based solvents as they may damage painted
surfaces should they come in contact. Always
follow the manufacturer’s instructions when using
any type of cleaning product.

Do not use gasoline or
other petroleum-based
solvents to clean with.
They have low flash
points which make them
extremely flammable.
A risk of explosion and
burning exists if these
products are used.

FLOOR LOAD

Your Professional Series Planer represents a
very large weight load in a moderate sized foot­print. Most commercial shop floors will be ade­quate for the 1030 lb. weight of the planer. Some
floors may require additional support. Contact an
architect or structural engineer if you have any
question about the ability of your floor to handle
the weight.

WORKING CLEARANCES

Working clearances can be thought of as the
distances between machines and obstacles that
allow safe operation of every machine with­out limitation. Consider existing and anticipated
machine needs, size of material to be processed
through each machine, and space for auxiliary
stands and/or work tables. Also consider the rela­tive position of each machine to one another for
efficient material handling. Be sure to allow your­self sufficient room to safely run your machines in
any foreseeable operation.

LIGHTING AND OUTLETS

Many of the solvents
commonly used to clean
machinery can be toxic
when inhaled or ingest­ed. Always work in well­ventilated areas far from
potential ignition sources
when dealing with sol­vents. Use care when dis­posing of waste rags and
towels to be sure they do
not create fire or environ­mental hazards.

Lighting should be bright enough to eliminate
shadow and prevent eye strain. Electrical circuits
should be dedicated or large enough to handle
combined motor amp loads. Outlets should be
located near each machine so power or exten­sion cords are not obstructing high-traffic areas.
Be sure to observe local electrical codes for prop­er installation of new lighting, outlets or circuits.

Make your shop “child safe.”
Ensure that your workplace
is inaccessible to children
by closing and locking all
entrances when you are
away. Never allow visitors
in your shop when assem­bling, adjusting or operat­ing equipment.

-10-

Professional Series Planers

SECTION 4: ASSEMBLY

Beginning Assembly

Most of your Professional Series Planer has
been assembled at the factory, but some parts
must be assembled or installed after delivery. We
have organized the assembly process into steps.
Please follow along in the order presented in this
section.

Keep loose clothing out
of the way of machin­ery and keep hair pulled
back.

Disconnect power to the
machine when perform­ing any maintenance or
assembly. Failure to do
this may result in serious
personal injury.

Dust Hood

A dust hood with a 5" dust port comes with the
planer for dust collection purposes. Install the
dust hood as shown in Figure 4 with the hex
bolts already mounted to the top of the planer.

Do not use the dust hood if dust collection is
not available.

Figure 4. Dust hood installed.

Wear safety glasses dur­ing the entire assembly
process. Failure to com­ply may result in serious
personal injury.

Planer knives are dan­gerously sharp! Use
extreme caution when
working near cutting sur­faces. Failure exercise
care while working near
knives could result in
severe injury.

Professional Series Planers -11-

Adjustment Handle

An adjustment handle has been provided with the
planer for adequate leverage when adjusting the
bed rollers.

To install the adjustment handle:

1. Screw the adjustment handle into the hub

that controls bed roller adjustments.

2. Tighten down the handle lock nut to the hub
to keep the handle secure.

SECTION 5: ADJUSTMENTS

Adjustment

Keep loose clothing out
of the way of machin­ery and keep hair pulled
back.

Disconnect power to the
machine when perform­ing any adjustments or
maintenance. Failure to
do this may result in seri­ous personal injury.

Wear safety glasses dur­ing the entire adjustment
process. Failure to com­ply may result in serious
personal injury.

Controls

Figures 5 and 6 point out the primary controls

and components that will be used during the
adjustment process. Take a few minutes to famil­iarize yourself with these.

Table Height

Handwheel

Table Height

Lock

Table Roller

Adjustment

Knob

Table Roller Lock

Control Panel

Feed Rate

Control

Planer knives are danger­ously sharp! Use extreme
caution when working
near cutting surfaces.
Failure to exercise care
while working near knives
could result in severe
injury.

Chipbreaker

Infeed
Roller

Figure 6. Planer components.

Figure 5. Planer controls.

Cutterhead

Table

Table Rollers

Rear

Pressure

Bar

Outfeed

Roller

-12- Professional Series Planers

Cutterhead Knives

The G5850Z, G5851Z & G7213 Professional
Series Planers feature 4-knife cutterheads. These
knives must be periodically replaced or adjusted.
To prolong the sharpness of the knife edges,
adjustments should be within .002" from one
side to the other. Improperly adjusted knives can
unbalance the cutterhead and shorten the bear­ing life, as well as produce substandard planing
results.

To adjust the knife set:

1. Before beginning, make sure you have fol-

lowed steps 1-4 from the previous knife
inspection instructions! See Figure 7 to
familiarize yourself with the components of
the cutterhead.

2. Loosen all the gib bolts (work on only one
knife at a time). Wear heavy leather gloves
or place a rag over the exposed knife to
protect your hands if the wrench slips while
loosening the gib bolts.

To be safe, always test the planer with a scrap
piece of wood before using expensive stock.

To inspect the knife set:

1. Make sure the planer is unplugged!

2. Open the top cover to gain access to the

cutterhead. Remove the pulley cover from
the left side of the machine (this will allow
you to rotate the cutterhead without putting
your hands near the blades).

3. The knife setting jig has special grooves cut
into it that fit the knife edge profile. One end
of the jig should be fixed in place and the
other end should be loose enough to swivel
and match the fixed end.

4. Place the jig on the cutterhead so the
grooves catch on the knife edge, keeping
the jig in place. If the knife is adjusted right,
the feet should touch the cutterhead body on
both sides of the knife, and the knife should
fit in the special grooves in the jig. Repeat
this inspection for the other three knives.

3. Using the holes in the cutterhead body for
access, insert a hex wrench into the jack
screws as shown in Figure 8. These screws
will allow you to lower/raise the knife.

Gib

Figure 7. Parts of the cutterhead.

Gib Bolt

Jack Screw

Knife

Planer knives are danger­ously sharp! Use extreme
caution when working
near cutting surfaces.
Failure to exercise care
while working near knives
could result in severe
injury.

Professional Series Planers -13-

Figure 8. Adjusting knife height.

4. Turn the jack screws with the hex wrench to

raise the knife so it barely touches the jig.
Perform this adjustment on both sides.

5. Snug, but do not completely tighten, one gib
bolt on each side then double check to make
sure that the knife did not move. The back

edge of beveled knife edge should never
be set below the cutterhead body.

6. Repeat steps 2-6 on the other three knives.

7. Now tighten the two center bolts of each of

the four knives. Tighten the next two bolts
from the center of each knife, and continue
tightening the rest of the gib bolts in this
manner until all bolts on all four knives have
been tightened.

Tightening the gib bolts evenly, two at a time,

each knife at a time, will prevent distortion
of the cutterhead from over-torquing the gib
bolts.

Aftermarket Knife Setting Jigs

To ease the knife adjustment process, consider

®

using Planer Pals

shown in Figure 9 and avail­able in the current Grizzly catalog. Using mag­nets, a pair of these devices will automatically
hold the knife blades within .001" of each other,
thereby allowing you to quickly and accurately
lock the knife in place.

8. Replace all of the removed planer parts and
adjust the pressure bar before operating the
planer (pressure bar adjustment is covered
later in this manual).

Figure 9. Planer Pal®.

Disconnect power to the
machine when perform­ing any adjustments or
maintenance. Failure
to do this may result in
serious personal injury.

-14- Professional Series Planers

Table

To obtain accurate results with your Professional
Series Planer, the table must be parallel with
the cutterhead. We strongly suggest using a
Rotacator
This tool is well worth the money, because it pro­vides accuracy to .001" and will save you hours of
frustration. Check with the current Grizzly catalog
for details.

As an alternative to using a Rotacator
a block of scrap wood to aid in checking the table.
The wood block should be rectangular and should
have one side that sits flat on the table. Make
the block tall enough to leave adequate working
room between the table and the cutterhead, but
thin enough to fit between the chip deflector and
pressure bar.

To check the table with a Rotacator

1. Make sure the planer is unplugged!

2. Set the Rotacator

®

for making adjustments to your planer.

®

, construct

®

:

®

dial to .000". Place the

Rotacator

®

under the cutterhead on one end.

Turn the cutterhead so the plunger on the

®

Rotacator

will contact the cutterhead body
as shown in Figure 10. Raise the table up
enough for the cutterhead to get a reading
on the dial.

3. Move the Rotacator® back and forth to find
bottom dead center on the cutterhead (you
will reach bottom dead center when you have

®

the highest reading on the Rotacator

.)

4. Now raise the table up so the Rotacator
reads exactly .050", and set the dial to
.000".

®

5. Move the Rotacator

to the other side of the
cutterhead and find bottom dead center. If
the difference in either direction of the dial
is more than .002", then the table should be
adjusted.

To check the table with the block of wood:

1. Make sure the planer is unplugged!

2. Place the block of wood on the table, under-

neath the cutterhead. Position the block on
the left side of the cutterhead as illustrated
in Figure 11.

3. Raise the table up until the top of the block
lightly contacts the bottom of the cutterhead
drum.

4. Without moving the table position, slide the
block over to the other side.

5. If the block will not fit under the cutterhead
or if the gap between the block and the
cutterhead exceeds .002" (use a feeler
gauge to measure this), the table must be
adjusted.

®

Figure 10. Rotacator measuring cutterhead/

table for being parallel to each other.

Figure 11. Using a wood block to determine if

table is parallel with cutterhead body.

Professional Series Planers -15-

To adjust the table with the Rotacator®:

To adjust the table with the wood block:

1. Make sure the planer is unplugged!

®

2. Set the Rotacator

®

Rotacator

under the cutterhead on the right-

dial to .000". Place the

hand side (facing front).

3. Turn the cutterhead so the plunger on the

®

Rotacator

will contact the cutterhead body.
Raise the table up enough for the cutterhead
to get a reading on the dial.

®

4. Move the Rotacator

back and forth to find
bottom dead center on the cutterhead. (You
will reach bottom dead center when you have

®

the highest reading on the Rotacator

.)

5. Adjust the table with the height handwheel

®

to make the dial on the Rotacator

read

.050", then set the dial to .000". Move the

®

Rotacator

over to the far left end of the

cutterhead and find bottom dead center.

6. Locate the two columns underneath the
table. These are covered in flexible rubber
sleeves. The column on the left hand side of
the machine (from the front) has a clamping
collar where it mounts to the table. Loosen
the pressure on this clamp and loosen the
two mounting bolts that secure the column
to the table.

1. Make sure the planer is unplugged!

2. Place the wood block on the far side of the

table where the tightest gap exists between
the table and the cutterhead.

3. Raise the table so the cutterhead barely
touches the wood block. Slide the wood
block to the other end of the table.

4. Locate the two columns underneath the
table. These are covered in flexible rubber
sleeves. The column on the left hand side of
the machine (from the front) has a clamping
collar where it mounts to the table. Loosen
the pressure on this clamp and loosen the
two mounting bolts that secure the column
to the table.

5. Pull the rubber sleeve down to expose
the adjustment collar shown in Figure 12.
Turning this collar counter-clockwise will
lower the left side of the table; turning this
collar clockwise will raise the left side of the
table.

7. Pull the rubber sleeve down to expose
the adjustment collar shown in Figure 11.
Turning this collar counter-clockwise will
lower the left side of the table; turning this
collar clockwise will raise the left side of the
table.

8. Turn the adjustment collar as necessary
to make the left side read .050" on the
Rotacator dial. Double check the table-to­cutterhead measurement on the right end to
make sure it did not move. Adjust as neces-

®

sary. The Rotacator

will allow you to easily

Figure 12. Column adjustment flange

underneath table.

get each end within .002" of each other.

9. When each end is adjusted properly, tighten
all of the nuts at the table mount and clamp.
Double check the table-to-cutterhead mea­surement to make sure the table did not
move.

-16- Professional Series Planers

6. Adjust the table as necessary until each
side is equal to or less than .003" from each
other. Use a feeler gauge to check the toler­ances.

7. Tighten all of the nuts at the table mount and
clamp. Double check the table-to-cutterhead
measurement to make sure the table did not
move.

8. Move the rubber sleeve back to its original
position. The rubber sleeves must cover
the lifting column to keep fine sawdust from
building up in the gear grease.

Table Gibs

The front of the table is equipped with gibs (see
Figure 13) to prevent the table from rocking back

and forth during operation.

These gibs should be adjusted individually so
they are lightly contacting all four surfaces. The
gibs should be tight enough to prevent rocking or
movement of the table during operation.

Figure 13. Table gib.

Professional Series Planers -17-

Feed Rollers,

Pressure Bar &

Chip Breaker

For most planing applications, the feed rollers,
pressure bar, and chipbreaker should be approxi­mately .040" below the knife edge at bottom dead
center. All of these components are factory

set. Adjusting them can be a difficult process
and is not recommended when the machine
is new, unless you are getting unsatisfactory
performance.

Figure 14. Feed roller adjustment controls

Although not required, we recommend using a
Rotacator
current Grizzly catalog for details. Also, remove
the cover on the left-hand side of the machine so
you can advance the cutterhead with the pulley.

To set the feed rollers, pressure bar, and
chipbreaker with a Rotacator

1. Make sure the planer is unplugged and

2. Place the Rotacator

3. Rotate the cutterhead so a knife edge will

®

for the following setup. Check with the

®

:

the knives are adjusted properly.

®

on the table, under­neath the cutterhead. Place the Rotacator
plunger against the body of the cutterhead.
Move the Rotacator
bottom dead center.

push the plunger down as far as it will go
before leaving bottom dead center. Set the
dial to .000" and lock in place.

®

back and forth to find

®

6. Adjust the pressure bar and chip breaker
using the same procedure as with the feed
rollers. The adjustment controls for each are
shown in Figures 15 and 16.

Figure 15. Pressure bar adjustment controls.

®

4. Move the Rotacator
of the feed roller and set the plunger on a
bottom dead center edge. With the adjust­ment screws shown in Figure 14, move the
feed roller down .040". (The feed roller has
two .040" indications on the dial. Do not skip
the first one as the needle moves clockwise
or your reading will actually be .060".)

5. Repeat step 4 on each end of each feed
roller. Double check for accuracy, then lock
the check nuts in place. While doing this,
watch the Rotacator
height setting does not change.

-18- Professional Series Planers

directly under one side

®

dial to make sure the

Figure 16. Chip breaker adjustment controls.

To set the feed rollers and pressure bar using
hardwood blocks:

1. Make sure the machine is unplugged and

the knives have been set up properly!

2. Obtain a milled piece of hardwood that is
within .002" from one side to another in thick­ness. Rip this piece down the middle. (Two
separate boards may also be used if they are
within .002" of each other in thickness.)

3. Lower the bed rollers below the surface of
the table.

4. Place the boards on each side of the table
as shown in Figure 17, so each board spans
from the front of the table to the back.

Because the table position is nearly even

with the knife edge, it will now be your ref­erence point from which to make the other
adjustments.

7. Lower the feed rollers so they rest on the
wood blocks. Back the adjustment bolts out
another

8. Notice the position of your pointer on the
table height scale (shown in Figure 18).
Lower the table approximately 1mm on this
scale (this is very close to .040").

1

⁄8" (approximately).

Figure 17. Board position on table.

5. Open the top cover. Loosen the feed roller

adjustment screws and turn the adjustment
bolts on each end to raise the feed roller up
approximately
bottom-dead-center horizontal plane of the
cutterhead knife/insert).

6. Place a sheet of newspaper on each wood
block. (This will act as a type of feeler gauge
while keeping your hands away from the
sharp knife edges.) Raise the table close to
the knife/insert edge. Continue raising the
table while constantly checking for resis­tance on the newspaper. When you get a
medium drag between the knife edge and
the wood block, stop raising the table and
remove the newspaper.

1

⁄2" (enough to be above the

Figure 18. Table height scale and pointer.

9. Tighten the check nuts while holding the

adjustment bolts in place so they do not
move.

10. Adjust the pressure bar stop bolt so the pres­sure bar rests on the wood blocks.

11. Tighten the check nut to keep the pressure
bar stop bolt in place.

The feed rollers and pressure bar should now be
approximately .040" below the knife edge.

NOTICE

The settings described here are to be used as a
guide and are not absolute. Raising or lowering
feed rollers/pressure bar for different types of
stock may increase the quality of your finished
results.

Professional Series Planers -19-

Table Rollers

After completing the table adjustments, set the
table rollers. The height of the table rollers will
vary, depending on the type of material you
intend to plane. When planing rough stock, you
will need to set the rollers high to keep the lum­ber from dragging along the table. Milled lumber
should be planed with the rollers set lower.

To adjust the table rollers:

1. Loosen the lock on the adjustment lever

shown in Figure 18. Moving the lever up will
raise the table rollers up.

Lock

If you have a Rotacator®, place it on the table

with the plunger against the table surface.
Set the dial to 0. Move it back and forth over
the table roller to find top dead center.

Figure 19. Rotacator

4. Adjust the roller height until it is satisfactory

for your particular situation.

®

on bed rollers.

Adjustment

Lever

Figure 18. Roller height adjustment controls.

2. Determine the appropriate height for the type

of stock you are using. The ideal tolerance

for the height of the bed rollers is between
.002"-.016". If the bed rollers are too high,
snipe or chipping may occur at the ends of
the workpiece. Only use the higher settings
for rough cut lumber. If you are unsure about
which height to use, experiment on scrap
lumber through trial and error. Always start
at smaller tolerances and work up.

3. Place a high quality straightedge across the
length of the table. Raise and lock the table
rollers and use a feeler gauge to measure
the distance between the bottom of the
straightedge and the table.

The first time you set your table rollers, and peri­odically after that, check the roller height at both
ends of the table. If one roller is more than .016"
different in height than the other roller, then the
roller adjustment equipment needs to be cor­rected. The adjustment bolts shown in Figure 20
allow you to move one end of the rollers to correct
this situation.

Figure 20. Roller adjustment bolts.

-20- Professional Series Planers

Feed Roller Tension

Test Run

The spring tension on the feed rollers is fac­tory set and should require no initial adjustments,
unless needed for a special type of stock. If a
situation develops where the workpiece does not
feed straight, adjustments to one roller may be
necessary. Usually if the board is moving more to
one side, that side needs less pressure.

Open the top cover of the planer and locate the
adjustment bolts attached to springs (shown in
Figure 21). Loosen the lock nuts and turn the
bolts clockwise to lower the feed rollers and coun­ter-clockwise to raise the feed rollers.

In general, rough stock or deeper cuts require
more feed rate pressure (spring tension). Shallow
cuts need less feed rate pressure. Too much
pressure increases snipe. Often the best way to
find a setting that is right for your application is
through trial and error.

Once assembly is complete and adjustments are
done to your satisfaction, you are ready to start
the machine.

Turn on the power supply at the main panel. Press
the START button. Make sure that your finger is
poised on the STOP button, just in case there is
a problem. The planer should run smoothly with
little or no vibration or rubbing noises. Strange or
unnatural noises should be investigated and cor­rected before operating the machine further.

Run the planer for a short time to ensure that the
moving parts are working properly with no exces­sive vibration. If any problem develops, correct it
before attempting to use the machine.

If you cannot locate the source of unusual noises
or cannot fix any problems that arise, immediately
contact our service department for help.

Figure 21. Feed roller spring tension bolts.

Read the entire manu­al before making any
cuts with your planer.
Serious personal injury
may result if safety or
operational information
is not understood or fol­lowed.

Professional Series Planers -21-

SECTION 6: OPERATIONS

Operation Controls

Keep loose clothing out
of the way of machin­ery and keep hair pulled
back.

Familiarize yourself with the planer controls
before turning the machine ON. See Figures 22

and 23.

Disconnect power to the
machine when perform­ing any adjustments or
maintenance. Failure to
do this may result in seri­ous personal injury.

Wear safety glasses dur­ing all operations on the
planer. Failure to com­ply may result in serious
personal injury.

Always wear a dust mask
when operating the plan­er. Using this machine
produces sawdust which
may cause allergic reac­tions or respiratory prob­lems.

Power

Indicator

Light

Cutterhead

Motor

Figure 22. Control panel.

Table Height

Handwheel

Table Roller

Adjustment

Knob

Main Power

and

Emergency

Stop

Feed Motor

Control Panel

Table Height

Lock

NOTICE

The following section is designed to give
instructions on the basic operations of this
planer. However, it is in no way compre­hensive of every planer application. WE
STRONGLY RECOMMEND that you read
books, trade magazines, or get formal
training to maximize the potential of your
planer.

-22- Professional Series Planers

Table Roller Lock

Figure 23. Planer controls.

Feed Rate

Control

Feed Rate

Operational Tips

The Professional Series Planers offer variable
feed rates between 17 and 26 FPM. Turning
the feed control knob (Figure 24) clockwise will
increase the feed rate and turning counter-clock­wise will decrease the feed rate.

In order to assure maximum belt life, only
adjust the feed rate while the feed motor is
moving!

• Inspect lumber for defects, warping, cup­ping, twisting, and for foreign objects (nails,
staples, imbedded gravel, etc.). If you have
any question about the quality of your lum­ber, do not use it. Remember, wood stacked
on a concrete floor can have small pieces of
stone or concrete pressed into its surface.

• Use the full width of the planer. Alternate
between the left, the right and the middle
when feeding lumber into the planer. Your
knives will remain sharp much longer.

• Scrape all glue off of joined boards before
planing.

• Plane ONLY natural wood fiber. No wood
composites.

• Surface wood with the grain. NEVER feed
end-cut or end-grained lumber into your
planer.

Figure 24. Variable speed control knob.

• Do not use boards with knots, splits, cross­grain or other obvious blemishes or defects.
They can damage the machine and they
pose the possibility of operator injury.

• Keep your work area clear.

• Avoid planing wood with a high water con­tent. Wood with more than 20% moisture
content or wood exposed to rain or snow will
plane poorly and cause excessive wear to
the knives and the motor. Excess moisture
can also hasten rust and corrosion.

• During operation, always use the table
height lock knob for consistent and accurate
results.

• Always true any cupped or warped stock on
a jointer before planing.

Professional Series Planers -23-

Wood Characteristics

The species of wood, as well as condition, will
affect planing ability—the harder the wood, the
more difficult it will be to plane. We have included
a list of wood characteristics you may encoun­ter when planing. The following descriptions of
defects will give you some possible answers to
problems you may encounter while planing differ­ent materials.

the planer components, but compete removal of
snipe is unlikely. More likely, you will be able to
reduce it to a tolerance of .002". If snipe under
that level is a problem, consider planing lumber
longer that your intended work length and cut off
the excess after planing is completed, or consider
sanding.

Uneven Knife Marks — Uneven knife marks
can occur when the chipbreaker is set too high.
Inspect cutterhead bearings if re-adjustment of
the chipbreaker fails to remedy the situation.

Chipped Grain (Tear Out) — Usually a result
of cutting against the grain, or planing wood
with knots or excessive amount of crossgrain.
Chipped grain can also be caused by dull knives
or a misaligned chipbreaker. Often, chipped grain
can be avoided by slowing down the feed rate
and by taking shallow cuts. If those options do
not work, inspect your lumber and determine if its
grain pattern is causing the problem. If the wood
does not show substantial crossgrain, unplug the
planer and inspect your knives for sharpness and
inspect the chipbreaker for proper alignment.

Fuzzy Grain (Raised Grain) — Usually caused
by surfacing lumber with too high of a moisture
content. Sometimes fuzzy grain is a characteristic
of wood such as basswood. Fuzzy grain can also
be caused by dull knives or an incorrect grinding
bevel. Check with a moisture meter. If moisture is
greater than 20%, sticker the wood and allow it to
dry. Otherwise, inspect the knife condition.

Glossy Surface — Usually caused by dull knives
taking shallow cuts at a slow feed speed. Surface
gloss will usually be accompanied by overheat­ing. Often lumber will be scorched, and eventu­ally, damage to knives will occur. If knives are
sharp upon inspection, increase feed speed or
cutting depth.

Snipe — Occurs when board ends have more
material removed than the rest of the board.
Usually caused when one or both of the bed roll­ers are set too high. Can also be caused by the
chipbreaker or pressure bar being set too high.
However, a small amount of snipe is often inevi­table.
Snipe can be minimized by proper adjustment of

Chatter Marks — Usually caused by incorrect
chipbreaker and pressure bar setting heights.
Chatter marks can also be caused by running a
narrow wood piece through the planer at either
the right or left end of the cutterhead. Chatter,
like uneven knife marks, will show in the form of a
“washboard” look. Chatter marks are more likely
to be inconsistent in appearance than uneven
knife marks.

Wavy Surface — Caused by poor knife height
adjustment, wavy surface appears when one
knife is taking deeper cuts than the rest of the
knives. Remedy by resetting the knives to a toler­ance within .001" from one end to the other.

Pitch & Glue Build-Up — Glue and resin build­up on the rollers and cutterhead will cause over­heating by decreasing cutting sharpness while
increasing drag in the feed mechanism. The
result can include scorched lumber as well as
uneven knife marks and chatter.

Chip Marks — Occur when chips are not prop­erly expelled from the cutterhead. The knives
catch the chips and drag them across the lum­ber being planed. Chips tend to be random and
non-uniform (compared to chipped grain). This
problem can be caused by exhaust blockage
or too much room between the cutterhead and
the chip deflector. Inspect the chip deflector and
re-adjust the spring tension. Also, using a dust
collection system with the planer can help reduce
chip marks.

-24- Professional Series Planers

SECTION 7: MAINTENANCE

Table

Disconnect power to the
machine when perform­ing any adjustments or
maintenance. Failure to
do this may result in seri­ous personal injury.

The table and other non-painted surfaces on the
Professional Series Planer should be protected
against rust and pitting. Wiping the table clean
after every use ensures that wood dust is not
allowed to trap moisture against bare metal sur­faces.

General

Regular periodic maintenance on your Professional
Series Planer ensures its optimum performance.
Make a habit of inspecting your planer each time
you use it.

Check for the following conditions and repair or
replace when necessary.

• Loose mounting bolts.

• Worn switch.

• Worn or damaged cords and plugs.

• Damaged V-belt.

• Any other condition that could hamper the

safe operation of this machine.

Tables can be kept rust-free with regular applica­tions of products like Boeshield
term storage you may want to consider products
like Kleen Bore's Rust Guardit™.

®

T-9. For long

Lubrication

The Professional Series Planers have four lubri­cation points that need to be lubricated accord­ing to planer usage. Always lubricate more often
under dusty/dirty conditions. As a general rule,
lubricate as follows:

1. Cutterhead Grease Fittings — Once a
week for heavy use; once a month for mod­erate use. See Figure 25 for grease fitting
location.

Cleaning

Regularly blow out cabinet, feed rollers, chip

breakers and cutterhead with compressed air
(always wear a dust mask when doing this) and
keep the dust port clear.

Figure 25. Grease fitting.

Professional Series Planers -25-

2. Spur/Table Lifting Gears — Clean and
regrease as determined by visible inspection
for dust or grime in the grease. See Figures

26 and 27 for gear locations.

Always wipe off excess grease from all loca­tions after lubricating!

V-Belt

Avoid getting grease or oil on the V-belts or pul­leys. Check the V-belts, as part of a monthly
inspection for proper tension and belt condition.
Cracking and glazing could result in belt failure.
Replace the belt if such conditions appear.

Once a year, under normal conditions, replace
the V-belt.

To loosen/tighten belt tension, use the adjust­ment nuts shown in Figure 28.

Figure 26. Location of spur gears.

Figure 27. Pull down rubber boots under the

table to expose the worm gears that raise and

lower the table.

Figure 28. Adjust feed motor V-belt here.

3. Table Gibs — Clean and grease gibs where

they slide against the planer body as needed
per visual inspection.

-26- Professional Series Planers

Indexable Inserts

(G0544)

The G0544 has a spiral cutterhead with 96
indexable inserts. Each cutter can be rotated
to reveal any one of its four cutting edges.
Therefore, if one cutting edge becomes dull or
damaged, simply rotate it 90˚ to reveal a fresh
cutting edge (Figure 29).

In addition, each cutter has a reference dot on
one corner. As the cutter is rotated, the reference
dot location can be used as an indicator of which
edges are used and which are new. When the
reference dot revolves back around to its starting
position, the cutter should be replaced.

To rotate or change a carbide cutter:

1. DISCONNECT THE PLANER FROM THE

POWER SOURCE!

Note: Proper cleaning is critical to achieving

a smooth finish. Dirt or dust trapped between
the cutter and cutterhead will slightly raise the
cutter, and make a noticeable marks on your
workpieces the next time you plane.

5. Lubricate the Torx screw threads with a
light machine oil, wipe the excess oil off the
threads, and torque the Torx screw to 48-50
inch/pounds.

Note: Excess oil may squeeze between the

cutter and cutterhead, thereby lifting the cutter
slightly and affecting workpiece finishes.

Reference Dot

2. Remove any sawdust from the head of the
carbide cutter Torx screw.

3. Remove the Torx screw and carbide cutter.

4. Clean all dust and dirt off the cutter and the

cutterhead pocket from which the cutter was
removed, and replace the cutter so a fresh,
sharp edge is facing outward.

Figure 29. Cutter rotating sequence.

Professional Series Planers -27-

G0544

1 3 2

FEED MOTOR

1 3 2

MAIN MOTOR

-28- Professional Series Planers

Professional Series Planers -29-

SECTION 8: CLOSURE

The following pages contain general machine
data, parts diagrams/lists, troubleshooting guide
and Warranty/Return information for your
Professional Series Planer.

If you need parts or help in assembling your
machine, or if you need operational informa­tion, we encourage you to call our Service
Department. Our trained service technicians will
be glad to help you.

If you have comments dealing specifically with
this manual, please write to our Bellingham,
Washington location using the address in the
General Information section. The specifications,
drawings, and photographs illustrated in this
manual represent the Professional Series Planer
as supplied when the manual was prepared.
However, due to Grizzly’s policy of continuous
improvement, changes may be made at any time
with no obligation on the part of Grizzly. Whenever
possible, though, we send manual updates to all
owners of a particular tool or machine. Should
you receive one, add the new information to this
manual and keep it for reference.

We recommend you keep a copy of our cur­rent catalog for complete information regarding
Grizzly's warranty and return policy. If you need
additional technical information relating to this
machine, or if you need general assistance or
replacement parts, please contact the Service
Department listed in the Introduction section.

Additional information sources are necessary to
realize the full potential of this machine. Trade
journals, woodworking magazines and your local
library are good places to start.

Operating this equipment has the potential
for flying debris to cause eye injury. Always
wear safety glasses or goggles when oper­ating equipment. Everyday glasses or read­ing glasses only have impact resistant
lenses, they are not safety glasses. Be
certain the safety glasses you wear meet
the appropriate standards of the American
National Standards Institute (ANSI).

We have included some important safety mea­sures that are essential to the operation of this
machine. While most safety measures are gen­erally universal, Grizzly reminds you that each
workshop is different and safety rules should be
considered as they apply to your specific situa­tion.

The Professional Series Planers were spe­cifically designed for wood planing opera­tions only. DO NOT MODIFY AND/OR USE
THIS MACHINE FOR ANY OTHER PURPOSE.
Modifications or improper use of this tool will
void the warranty. If you are confused about
any aspect of this machine, DO NOT use it
until all your questions have been answered,
or serious personal injury may occur.

Like all power tools, there is danger associ­ated with the Professional Series Planers.
Accidents are frequently caused by lack of
familiarity or failure to pay attention. Use
your machine with respect and caution to
lessen the possibility of operator injury. If
normal safety precautions are overlooked or
ignored, serious personal injury may occur.

-30- Professional Series Planers

MACHINE DATA

SHEET

Customer Service #: [phone] • To Order Call: [phone] • Fax #: [phone]

MODEL G5850Z 20" PROFESSIONAL PLANER

MODEL G0544 20" PLANER W/ SPIRAL CUTTERHEAD

Design Type .................................................................................................... Floor Model

Overall Dimensions:

Table Size .................................................................................................211⁄4'' x 281⁄4''

Overall Height .......................................................................................................42

Overall Depth ........................................................................................................40

Overall Width ............................................................................................................38''

Shipping Weight ............................................................................................... 990 lbs.

Footprint ....................................................................................................24

Crate Size ............................................................................46" H x 42

Capacities:

Maximum Depth of Cut .............................................................................................

Maximum Width of Cut ....................................................................................................20''

1

1

⁄2" W x 413⁄8" D

1

1

⁄2'' x 261⁄2''

1

⁄8''

⁄4''
⁄2''

Maximum Cutting Height ............................................................................................ 7''

Minimum Stock Thickness .......................................................................................

Minimum Stock Length ...............................................................................................8''

Cutterhead Diameter ............................................................................................... 3

Knives (G5850Z) .................................................... 4 High Speed Steel / 20" x 1" x

Knives (G0544) .........................................Indexable Carbide Inserts / 14 x 14 x 2mm

Cutterhead Speed ........................................................................................ 5200 RPM

Cuts Per Minute .................................................................................................20,800

Feed Rate .....................................................................................Variable 17-26 FPM

Cuts Per Inch .....................................................................................................66-101

Construction:

Table ................................................................................. Precision-Ground Cast Iron

Power Feed Rollers ..................................Steel, Segmented Infeed, Polished Outfeed

Cutterhead (G5850Z) ......................................... 4 Knife Slots, Shielded Ball Bearings

Cutterhead (G0544) .............................................. Spiral Cutterhead w/ 96 pc. Inserts

Planer Motor:

Type ............................................................................TEFC Capacitor-Start Induction

Horsepower ........................................................................................................... 5 HP

Phase ⁄ Voltage ............................................................................ Single-Phase / 220V

Amps ......................................................................................................................25 A

Cycle ⁄ RPM ..................................................................................60 Hertz ⁄ 3450 RPM

Switch ........................................................Magnetic With Thermal Overload Protector

Power Transfer .................................................................................. Twin V-Belt Drive

Bearings ................................................................. Sealed & Lubricated Ball Bearings

Feed Motor:

Type ............................................................................TEFC Capacitor-Start Induction

Horsepower ........................................................................................................... 2 HP

Phase ⁄ Voltage .............................................................................Single-Phase ⁄ 220V

Amps ......................................................................................................................... 14

Cycle ⁄ RPM ..................................................................................60 Hertz ⁄ 3450 RPM

Power Transfer .................................................................Variable Split Pulley System

Phase ⁄ Voltage ............................................................................. Single-Phase, 220V

Features:

........................................................................................ Lever Controlled Bed Rollers

.......................................................................................Handwheel Depth Adjustment

...................................................................................................................5" Dust Port

.................................Dust Covers Protect Vertical Support Columns and Leadscrews

1

⁄4''

1

⁄8"

1

⁄8"

Professional Series Planers -31-

178-1V2

178-2V2

127

126

7

6

5

6

10

154

136

135

131

132

193

193

174

8

15

123

16

122

17

119

122

18

123

15

1

135

177

20

147

146

14

13

154

11

12

7

139

139

139

178

140

139

201

202

201

139

137

194

133

138

148

149

119

143

144

124

125

124

125

120

19

121

128

200

145

142

131

132

134

133

203

136

134

G5850Z

G0544

-32- Professional Series Planers

G5850Z

66

67

57

191

61

197

56

54

63

53

59

70

65

71

58

52

73

64-1

64-2

63

72

62

68

69

75

51-1

192

72

60

55

76

300-1

G5851Z 24''

Variable Speed Planer

184

77

79

220V

52

158

159

300-2

51-1

51

157

301

300-3

153

186

155

301-1

300-4

48

50

300

151

180

152

181

182

G0544

150

179

195

207

209

210

19

17

208

206

46

47

G5850Z

ONLY

ONLY

188

155

183

G0544

156

187

186

129

198

51-1

402

51-2

403

Professional Series Planers -33-

51

105

106

29

28

45

98

95

96

97

44

25

30

29

28

80

90

99

92

139

94

93

94

42

90

43

92

39

31

25

85

38

85

74

24

185

33

27

107

108

3

205

27

35

36

85

185

24

2

106

32

90

40

91

41

93

100

80

106

81

106

106

81

81

80

86

87

37

26

80

199

88

89

26

25B

25B

34

34

91

66

84

204

103

104

106

G5850Z

G0544

-34- Professional Series Planers

161

162

163

167

166

168

172

174

173

164

165

166

175

171

171-2

169

214

170

21

111

23

22

102

102

189

189

190

190

101

101

160

166

4

109

110

114

115

113

176

175

175

116

117

112

176

G5850Z

G0544

Professional Series Planers -35-

G5850Z/G0544

REF PART # DESCRIPTION REF PART # DESCRIPTION

1 P5850Z001 BASE 54 P5850Z054 PRESSURE SPRING LEFT
2 P5850Z002 COLUMN 55 P5850Z055 PRESSURE SPRING RIGHT
3 P5850Z003 COLUMN 56 P5850Z056 OUTFEED ROLLER
4 P5850Z004 TABLE 57 P5850Z057 COVER HINGE BRACKET LH
5 P5850Z005 GEAR SHAFT 58 P5850Z058 COVER SIDE PLATE LH
6 P5850Z006 BEVEL GEAR 14T 59 P5850Z059 CHIPBREAKER SHAFT
7 P5850Z007 BEVEL GEAR 24T 60 P5850Z060 CHIPBREAKER
8 P5850Z008 END BRACKET 61 P5850Z061 CHIPBREAKER SPRING
10 P5850Z010 BEVEL GEAR 24T 62 P5850Z062 COVER SIDE PLATE RH
11 P5850Z011 BEVEL GEAR 13T 63 P5850Z063 RETURN ROLLERS
12 P5850Z012 BEVEL GEAR HOUSING 64-1 P5850Z064-1 GIB W/O GIB BOLTS
13 P5850Z013 HANDWHEEL SHAFT 64-2 P5850Z064-2 GIB BOLT
14 P5850Z014 SHAFT RING 65 P5850Z065 KNIFE 4PC 20"
15 P5850Z015 BEARING HOUSING 66 P5850Z066 HEX BOLT 3/8"-16 X 1-1/4"
16 P5850Z016 ELEVATING SCR 1-6 X 17-1/2" 67 P5850Z067 LOCK WASHER 3/8"
17 P5850Z017 ELEVATING SCR BRACKET LH 68 P5850Z068 HEX BOLT 3/8"-16 X 2"
18 P5850Z018 ELEVATING SCR 1-6 X 17-1/2" 69 P5850Z069 HEX NUT 3/8"-16
19 P5850Z019 ELVTNG SCR ADJ M36-2.0 70 P5850Z070 HEX BOLT 1/4"-20 X 5/8"
20 P5850Z020 ELEVATING SCR BRACKET RH 71 P5850Z071 LOCK WASHER 1/4"
21 P5850Z021 TABLE ROLLER ADJ PIN 72 P5850Z072 ACORN NUT 1/2"-12
22 P5850Z022 TABLE ROLLER SHAFT 73 P5850Z073 HEX BOLT 5/16"-18 X 1"
23 P5850Z023 TABLE ROLLER 74 P5850Z074 HEX BOLT 5/16"-18 X 5/8"
24 P5850Z024 OUTFEED ROLLER MOUNT 75 P5850Z075 KEY 1/4" X 1/4" X 3/4"
25 P5850Z025 BEARING LOCKING RING RH 76 P5850Z076 HEX BOLT 5/16"-18 X 5/8"
25B P5850Z025B BEARING LOCKING RING LH 77 P5850Z077 LOCK WASHER 5/16"
26 P5850Z026 THREADED CAP 79 P5850Z079 KEY 1/4" X 1/4" X 3/4"
27 P5850Z027 INFEED ROLLER MOUNT 80 P5850Z080 BALL BEARING 6205ZZ
28 P5850Z028 BEARING LOCKING RING 81 P5850Z081 HEX BOLT 3/8"-16 X 13/4"
29 P5850Z029 SPACER 84 P5850Z084 LOCK WASHER 3/8"
30 P5850Z030 INFEED GEAR 38T 85 P5850Z085 BALL BEARING 6206ZZ
31 P5850Z031 OUTFEED GEAR 26T 86 P5850Z086 INT RETAINING RING 27MM
32 P5850Z032 CUTTERHEAD MOUNT LH 87 P5850Z087 LOCKING RING 15/16-16 RH
33 P5850Z033 CUTTERHEAD MOUNT RH 88 P5850Z088 LOCK WASHER 3/8"
34 P5850Z034 BEARING LOCKING RING 89 P5850Z089 HEX BOLT 3/8"-16 X 1"
35 P5850Z035 PULLEY 2-3/4" 90 P5850Z090 BALL BEARING 6002ZZ
36 P5850Z036 NUT M30-1.5 LH 91 P5850Z091 BALL BEARING 6201ZZ
37 P5850Z037 SPACER 92 P5850Z092 FLAT WASHER 5/16"
38 P5850Z038 CUTTERHEAD GEAR 25T 93 P5850Z093 LOCK WASHER 5/16"
39 P5850Z039 ADJUSTING BRACKET 94 P5850Z094 HEX BOLT 5/16"-18 X 3/8"
40 P5850Z040 GEAR 14T 95 P5850Z095 FLAT WASHER 3/8"
41 P5850Z041 GEAR 76T 96 P5850Z096 LOCK WASHER 3/8"
42 P5850Z042 PULLEY 7" 97 P5850Z097 HEX BOLT 3/8"-16 X 1"
43 P5850Z043 GEAR 18T 98 P5850Z098 BALL BEARING 6003ZZ
44 P5850Z044 ADJUSTING BRACKET 99 P5850Z099 HEX NUT 5/8"-11
45 P5850Z045 PULLEY 10" 100 P5850Z100 V-BELT A32
46 P5850Z046 SAFETY FENDER 101 P5850Z101 EXT RETAINING RING 19MM
47 P5850Z047 LOCK COLLAR LH 102 P5850Z102 BALL BEARING 6304ZZ
48 P5850Z048 INFEED ROLLER SOLID SLEEVE 103 P5850Z103 STUD-UDE 3/8-16 X 6-3/16 1-1/8RH 1-7/8RH
50 P5850Z050 LOCK COLLAR RH 104 P5850Z104 COMPRESSION SPRING
51 P0544051 SPIRAL CUTTERHEAD 105 P5850Z105 FLAT WASHER 3/8"
51 P5850Z051 CUTTERHEAD 20" 4 KNIFE 106 P5850Z106 HEX NUT 3/8"-16
51-1 P0544051-1 INDEXABLE CARBIDE INSERTS 10PK 107 P5850Z107 HEX BOLT 1/2"-12 X 1-1/2"
51-1 P5850Z051 FLAT HEAD SCREW M6-1 X 16 108 P5850Z108 LOCK WASHER 1/2"
51-2 P0544051-2 FLAT HEAD TORX SCREW T20 M6-1 X15 109 P5850Z109 TABLE EDGE GUIDE
52 P5850Z052 PRESSURE BAR BRACKET 110 P5850Z110 CAP SCREW 1/4-20 X 1/2
53 P5850Z053 PRESSURE BAR

-36- Professional Series Planers

G5850Z/G0544

REF PART # DESCRIPTION REF PART # DESCRIPTION

111 P5850Z111 TABLE GIB 169 P5850Z169 ARC HUB
112 P5850Z112 HEX NUT 3/8"-16 170 P5850Z170 LOCK HANDLE 1/2-12
113 P5850Z113 HEX BOLT 3/8"-16 X 1-3/4" 171 P5850Z171 HANDLE ASSEMBLY 1/2-12
114 P5850Z114 SCALE POINTER 172 P5850Z172 CAP SCREW 5/16-18 X 1
115 P5850Z115 CAP SCREW 1/4-20 X 3/8 173 P5850Z173 SET SCREW 3/8"-16 X 3/8"
116 P5850Z116 HEX NUT 3/8"-16 174 P5850Z174 FLAT WASHER 1/2"
117 P5850Z117 HEX BOLT 3/8"-16 X 2" 175 P5850Z175 SET SCREW 5/16"-18 X 3/8"
119 P5850Z119 HEX BOLT 5/16"-18 X 1-1/4" 176 P5850Z176 SET SCREW 5/16"-18 X1/4"
120 P5850Z120 LOCK WASHER 5/16" 177 P5850Z177 FEED MOTOR 2HP 220V 1PH
121 P5850Z121 HEX BOLT 5/16"-18 X 1" 178 P5850Z178 VARIABLE SPEED CONTROLLER V1
122 P5850Z122 DUST BOOT 179 P5850Z179 CONTROL PANEL
123 P5850Z123 THRUST BEARING 2904 180 P5850Z180 POWER INDICATOR LIGHT
124 P5850Z124 HEX BOLT 5/16"-18 X 1" 181 P5850Z181 EMERGENCY STOP SWITCH
125 P5850Z125 LOCK WASHER 5/16" 182 P5850Z182 CUTTERHEAD MOTOR ON BUTTON
126 P5850Z126 MOTOR 5HP 220V 1PH 183 P5850Z183 GRIZZLY NAME PLATE
127 P5850Z127 PULLEY 184 P5850Z184 MACHINE ID LABEL
128 P5850Z128 V-BELT A60 185 P5850Z185 GREASE FITTING
129 P5850Z129 GUARD LEFT 186 P5850Z186 DO NOT OPEN WARNING
131 P5850Z131 HEX BOLT 3/8"-16 X 1-1/2" 187 P5850Z187 SAFETY GLASSES LABEL
132 P5850Z132 FLAT WASHER 3/8" 188 P5850Z188 READ MANUAL LABEL
133 P5850Z133 LOCK WASHER 3/8" 189 P5850Z189 SET SCREW 1/4"-20 X 1/4"
134 P5850Z134 HEX NUT 3/8"-16 190 P5850Z190 BED ROLLER BASE
135 P5850Z135 MOTOR ADJUSTMENT BRACKET 191 P5850Z191 DUST HOOD
136 P5850Z136 HEX NUT 3/8"-16 192 P5850Z192 CHIPBREAKER SIDE PLATE
137 P5850Z137 HEX BOLT 5/16"-18 X 1" 193 P5850Z193 HEX NUT 1/2"-12
138 P5850Z138 LOCK WASHER 5/16" 194 P5850Z194 HEX BOLT 1/2"-12 X 4"
139 P5850Z139 SET SCREW 1/4"-20 X 3/8" 195 P5850Z195 POWER FEED ON BUTTON
140 P5850Z140 SET SCREW 5/16"-18 X 3/8" 197 P5850Z197 SUPPORT SHAFT
142 P5850Z142 FLAT WASHER 1/2" 198 P5850Z198 COVER
143 P5850Z143 LOCK WASHER 5/16" 199 P5850Z199 MOTOR ADJUSTMENT BRACKET
144 P5850Z144 HEX BOLT 5/16"-18 X 1" 200 P5850Z200 KEY 8 X 10 X 64
145 P5850Z145 ACORN NUT 1/2"-12 201 P5850Z201 FLAT WASHER 3/8"
146 P5850Z146 HANDWHEEL 202 P5850Z202 HEX BOLT 3/8-16 X 6
147 P5850Z147 MOVEABLE HANDLE 203 P5850Z203 COMPRESSION SPRING
148 P5850Z148 LOCK WASHER 5/16" 204 P5850Z204 V-BELT A46
149 P5850Z149 HEX BOLT 5/16"-18 X 1" 205 P5850Z205 DEPTH GAUGE
150 P5850Z150 GUARD RIGHT 206 P5850Z206 KNIFE GAUGE ASSEMBLY
151 P5850Z151 FLAT WASHER 1/4" 207 P5850Z207 WRENCH 17 X 19MM OPEN ENDS
152 P5850Z152 CAP SCREW 1/4-20 X 1/2 208 P5850Z208 WRENCH 12 X 14MM OPEN ENDS
153 P5850Z153 CONTROL CASE 209 P5850Z209 WRENCH 8 X 10MM OPEN ENDS

154 P5850Z154 MOTOR SUPPORT 210 P5850Z210 HEX WRENCH 4MM
155 P5850Z155 MOUNTING BRACKET LH/RH 211 P5850Z211 *DISCD*LOCKING NUT
156 P5850Z156 SHAFT 212 P5850Z212 *DISCD*SPACER
157 P5850Z157 FIXED SHAFT 213 P5850Z213 HEX BOLT 3/8-16 X 6
158 P5850Z158 SPACER 214 P5850Z214 HEX NUT 1/2"-12
159 P5850Z159 ANTI KICKBACK TOOTH 300 P5850Z300 MAG SWITCH ASSY
160 P5850Z160 CHAIN SHAFT 300-1 P5850Z300-1 CONTACTOR RAB-18T10 RIKEN
161 P5850Z161 CHAIN 1/2" X 26" 300-2 P5850Z300-2 HEATER FEED MOTOR BTH18T2H18 12/18A
162 P5850Z162 CHAIN 1/2" X 21-1/2" 300-3 P5850Z300-3 CONTACTOR RAB-35T10
163 P5850Z163 SPROCKET 14T 300-4 P5850Z300-4 HEATER CUTTERHEAD BTH352H36 24/36A RIKEN
164 P5850Z164 DOUBLE SPROCKET 14T 301 P5850Z301 FUSE HOLDER
165 P5850Z165 SPROCKET 14T 301-1 P5850Z301-1 FUSE 2A
166 P5850Z166 COLLAR 402 P0544402 T-20 TORX BIT
167 P5850Z167 SHAFT 403 P0544403 T-20 TORX DRIVER
168 P5850Z168 HUB MOUNTING PLATE

Professional Series Planers -37-

MACHINE DATA

SHEET

Customer Service #: [phone] • To Order Call: [phone] • Fax #: [phone]

MODEL G5851Z 24" PROFESSIONAL PLANER

Design Type .................................................................................................... Floor Model

Overall Dimensions:

Table Size .................................................................................................24

Height ....................................................................................................................... 37"

Overall Depth ........................................................................................................40

Overall Width ............................................................................................................42"

Shipping Weight ............................................................................................. 1240 lbs.

Crate Size ............................................................................46" H x 47

Footprint ............................................................................................ 24

Capacities:

Maximum Depth of Cut .............................................................................................

Maximum Width of Cut ....................................................................................................24"

Maximum Cutting Height ............................................................................................ 7"

Minimum Stock Thickness .......................................................................................

Minimum Stock Length ...............................................................................................8"

Cutterhead Diameter ............................................................................................... 3

Knives (#/Dimension) ............................................. 4 High Speed Steel / 24" x 1" x

Cutterhead Speed ........................................................................................ 5200 RPM

Cuts Per Minute .................................................................................................20,800

Feed Rate .................................................................................... Variable 17-26 FPM

Cuts Per Inch .....................................................................................................66-101

Construction:

Table ................................................................................. Precision-Ground Cast Iron

Power Feed Rollers ............................................................... Steel, Segmented Infeed

Out Feed Roller .............................................................................. Fine Finished Steel

Cutterhead .............One Piece Machine Shaft; 4 Knife Slots; Shielded Ball Bearings

Planer Motor:

Type ............................................................................TEFC Capacitor-Start Induction

Horsepower ........................................................................................................... 5 HP

Phase ⁄ Voltage .............................................................................Single-Phase ⁄ 220V

Amps ......................................................................................................................... 25

Cycle ⁄ RPM ..................................................................................60 Hertz ⁄ 3450 RPM

Switch ........................................................Magnetic With Thermal Overload Protector

Power Transfer .................................................................................. Twin V-Belt Drive

Bearings ................................................................. Sealed & Lubricated Ball Bearings

Feed Motor:

Type ............................................................................TEFC Capacitor-Start Induction

Horsepower ........................................................................................................... 2 HP

Phase ⁄ Voltage .............................................................................Single-Phase ⁄ 220V

Amps ......................................................................................................................... 12

Cycle ⁄ RPM ..................................................................................60 Hertz ⁄ 3450 RPM

Power Transfer .................................................................Variable Split Pulley System

Features:

........................................................................................Lever Controlled Bed Rollers

...................................................................................... Handwheel Depth Adjustment

.............................................................................................Segmented Chip Breaker

................................................................................................................... Table Locks

...................................................................................................................5" Dust Port

................................................................................Inch & Metric Measurement Scale

.................................................................................................... Board Return Rollers

................................ Dust Covers Protect Vertical Support Columns and Leadscrews

......................................................................................Grease Fittings on Cutterhead

1

⁄8" x 311⁄8"

1

⁄4" W x 421⁄2" D

1

⁄2" L x 201⁄2" W

1

⁄2"

1

⁄8"

1

⁄4"

1

⁄8"

1

⁄8"

-38- Professional Series Planers

MACHINE DATA

SHEET

Customer Service #: [phone] • To Order Call: [phone] • Fax #: [phone]

MODEL G7213Z 24" PROFESSIONAL PLANER

Design Type .................................................................................................... Floor Model

Overall Dimensions:

Table Size ....................................................................................................311⁄2" x 24"

Height ....................................................................................................................... 37"

Overall Depth ...........................................................................................................33"

Overall Width .........................................................................................................27

Shipping Weight ............................................................................................. 1030 lbs.

Footprint ............................................................................................... 30" L x 20

Crate Size ...............................................................................42

Capacities:

Maximum Depth of Cut .............................................................................................

Maximum Width of Cut ....................................................................................................24"

1

⁄2" L x 36" W x 45" H

1

⁄2" W

1

⁄2"

1

⁄8"

Maximum Cutting Height ............................................................................................ 7"

Minimum Stock Thickness .......................................................................................

Minimum Stock Length ............................................................................................7

Cutterhead Speed ........................................................................................ 5200 RPM

Cuts Per Inch .....................................................................................................66-101

Cuts Per Minute .................................................................................................20,800

Feed Rate .................................................................................................. 17-26 FPM

Construction:

Table ................................................................................. Precision-Ground Cast Iron

Power Feed Rollers ...............................................................................................Steel

Out Feed Roller .............................................................................. Fine Finished Steel

Cutterhead .............................4 Knife Slots Sealed Ball Bearings with Grease Fitting

Planer Motor:

Type .....................................................................................................TEFC Induction

Horsepower ........................................................................................................ 7

Phase ⁄ Voltage .....................................................................Three-Phase; 220 ⁄ 440V

Amps .................................................................................................................. 20 / 10

Cycle ⁄ RPM ..................................................................................60 Hertz ⁄ 3450 RPM

Prewired ................................................................................................................220V

Switch ................................... Magnetic With Thermal Overload Protector / 220V Only

Power Transfer .......................................................................................Two Belt Drive

Feed Motor:

Type ..................................................................................................... TEFC Induction

Horsepower ........................................................................................................... 2 HP

Phase ⁄ Voltage .....................................................................Three-Phase; 220 ⁄ 440V

Amps ....................................................................................................................... 6/ 3

Prewired ................................................................................................................220V

Power Transfer .................................................................Variable Split Pulley System

Features:

.............................................................................................Lever Control Bed Rollers

................................................................ Segmented Chip Breaker and Infeed Roller

................................................................................................................... Table Locks

..................................................................................................... 5" Collar Chip Chute

................................................................................Inch & Metric Measurement Scale

......................................................................................................Variable speed feed

1

⁄2 HP

1

⁄4"

1

⁄2"

Specifications, while deemed accurate, are not guaranteed.

Professional Series Planers -39-

178

127

126

7

6

5

6

10

154

136

135

131

132

193

193

174

8

15

123

16

122

17

119

122

18

123

15

1

135

177

20

147

146

14

13

154

11

12

7

139

139

139

140

139

201

202

201

139

137

133

138

148

149

119

143

144

124

125

124

125

120

19

121

128

200

145

142

0

6

11

5

10

4

9

3

8

2

7

1

131

132

134

133

203

136

134

G5851Z
G7213Z

-40- Professional Series Planers

191

59

73

72

62

192

220V

300-1

300-2

301-1

301

300-3

G5851Z
G7213Z

300-4

66

67

57

61

197

63

70

71

58

63

68

69

75

55

72

60

76

G5851Z 24''

Variable Speed Planer

184

77

79

52

51-1

51

153

186

50

300

151

180

152

181

182

150

179

195

188

187

56

186

54

53

129

65

52

64

51-1

155

47

159

158

156

157

155

48

183

46

198

206

210

209

208

WRETCHED WRENCH CO.

17 19

207

Professional Series Planers -41-

105

106

0123456

7

grizzly.com

29

28

45

98

95

96

97

44

25

30

29

28

80

212

90

99

92

211

139

94

93

94

42

90

43

92

39

31

25

85

38

85

74

24

185

33

27

107

108

3

205

27

35

36

85

185

24

2

106

32

90

40

91

41

93

100

80

69

81

69

81

69

81

80

86

87

37

26

25B

80

199

88

89

B

O

B

A

S

B

E

A

R

I

N

G

C

O

6

2

0

6

-

2

R

S

26

25B

34

34

91

66

84

204

103

104

106

G5851Z
G7213Z

-42- Professional Series Planers

B

O

B

A

S

B

E

A

R

I

N

G

C

O

6

3

0

4

-

2

R

S

B

O

B

A

S

B

E

A

R

I

N

G

C

O

6

3

0

4

-

2

R

S

161

162

163

167

166

168

172

174

173

164

165

166

175

171

169

193

170

21

111

B

O

B

A

S

B

E

A

R

I

N

G

C

O

6

3

0

4

-

2

R

S

B

O

B

A

S

B

E

A

R

I

N

G

C

O

6

3

0

4

-

2

R

S

23

22

102

102

189

189

190

190

101

101

160

166

4

109

110

114

115

113

176

175

175

116

117

112

G5851Z
G7213Z

Professional Series Planers -43-

G5851Z & G7213Z

REF PART # DESCRIPTION REF PART # DESCRIPTION

1 P5851Z001 BASE 55 P5851Z055 SPRING
2 P5851Z002 COLUMN 56 P5851Z056 OUTFEED ROLLER
3 P5851Z003 COLUMN 57 P5851Z057 COVER HINGE BRACKET LH

4 P5851Z004 TABLE 58 P5851Z058 COVER SIDE PLATE LH
5 P5851Z005 GEAR SHAFT 59 P5851Z059 CHIPBREAKER SHAFT
6 P5851Z006 BEVEL GEAR 60 P5851Z060 CHIPBREAKER
7 P5851Z007 BEVEL GEAR 61 P5851Z061 CHIPBREAKER SPRING
8 P5851Z008 END BRACKET 62 P5851Z062 COVER SIDE PLATE RH
10 P5851Z010 BEVEL GEAR 63 P5851Z063 RETURN ROLLER 5/16" INSIDE THREAD
11 P5851Z011 BEVEL GEAR 64 P5851Z064 GIB W/ GIB BOLTS
12 P5851Z012 BEVEL GEAR HOUSING 64A P5851Z064A KNIFE SETTING GUAGE
13 P5851Z013 HANDWHEEL SHAFT 65 P5851Z065 KNIFE 4PC 24 X 1"
14 P5851Z014 SHAFT RING 66 P5851Z066 HEX BOLT 3/8-16 X 1-1/4
15 P5851Z015 BEARING HOUSING 67 P5851Z067 LOCK WASHER 3/8
16 P5851Z016 ELEVATING SCREW 1-6X17-1/2" 68 P5851Z068 HEX BOLT 3/8-16 X 2
17 P5851Z017 ELEVATING SCREW BRACKET LEFT SIDE 69 P5851Z069 HEX NUT 3/8"-16
18 P5851Z018 ELEVATING SCREW 1-6X17-1/2" 70 P5851Z070 HEX BOLT 1/4-20 X 5/8
19 P5851Z019 ELEVATING SCREW ADJUSTING NUT 71 P5851Z071 LOCK WASHER 1/4
20 P5851Z020 ELEVATING SCREW BRACKET RIGHT SIDE 72 P5851Z072 ACORN NUT 1/2-12
21 P5851Z021 TABLE ROLLER ADJ PIN 73 P5851Z073 HEX BOLT 5/16-18 X 1
22 P5851Z022 TABLE ROLLER SHAFT 74 P5851Z074 HEX BOLT 5/16-18 X 5/8
23 P5851Z023 TABLE ROLLER 75 P5851Z075 KEY 1/4 X 1/4 X 3/4
24 P5851Z024 OUTFEED ROLLER MOUNT LH 76 P5851Z076 HEX BOLT 5/16-18 X 5/8
25 P5851Z025 BEARING LOCKING RING RH 77 P5851Z077 LOCK WASHER 5/16
25B P5851Z025B BEARING LOCKING RING LH 79 P5851Z079 KEY 1/4 X 1/4 X 3/4
26 P5851Z026 ROUND NUT 80 P5851Z080 BALL BEARING 6205ZZ
27 P5851Z027 INFEED ROLLER MOUNT LH 81 P5851Z081 HEX BOLT 3/8-16 X 1-3/4
28 P5851Z028 BEARING LOCKING RING 84 P5851Z084 LOCK WASHER 3/8
29 P5851Z029 SPACER 85 P5851Z085 BALL BEARING 6206ZZ
30 P5851Z030 INFEED GEAR 38T 86 P5851Z086 INT RETAINING RING 27MM
31 P5851Z031 OUTFEED GEAR 26T 87 P5851Z087 BEARING LOCKING RING 15/16-16 RH R SIDE
32 P5851Z032 CUTTERHEAD MOUNT LH 88 P5851Z088 LOCK WASHER 3/8
33 P5851Z033 CUTTERHEAD MOUNT RH 89 P5851Z089 HEX BOLT 3/8-16 X 1
34 P5851Z034 BEARING LOCKING RING 90 P5851Z090 BALL BEARING 6002ZZ
35 P5851Z035 PULLEY 2-3/4" 91 P5851Z091 BALL BEARING 6201ZZ
36 P5851Z036 NUT M30-1.5 LH 92 P5851Z092 FLAT WASHER 5/16
37 P5851Z037 SPACER 93 P5851Z093 LOCK WASHER 5/16
38 P5851Z038 CUTTERHEAD GEAR 25T 94 P5851Z094 HEX BOLT 5/16-18 X 3/8
39 P5851Z039 ADJUSTING BRACKET 95 P5851Z095 FLAT WASHER 3/8
40 P5851Z040 GEAR 14T 96 P5851Z096 LOCK WASHER 3/8
41 P5851Z041 GEAR 76T 97 P5851Z097 HEX BOLT 3/8-16 X 1
42 P5851Z042 PULLEY 7" 98 P5851Z098 BALL BEARING 6003ZZ
43 P5851Z043 GEAR 18T 99 P5851Z099 HEX NUT 5/8"-11
44 P5851Z044 ADJUSTING BRACKET 100 P5851Z100 V-BELT 4L320 (QTY 1)
45 P5851Z045 PULLEY 10" 101 P5851Z101 EXT RETAINING RING 19MM
46 P5851Z046 SAFETY FENDER 102 P5851Z102 BALL BEARING 6304ZZ
47 P5851Z047 LOCK COLLAR LH 103 P5851Z103 STUD 3/8"-16 X 6"
48 P5851Z048 INFEED ROLLER 104 P5851Z104 SPRING
50 P5851Z050 LOCK COLLAR RH 105 P5851Z105 FLAT WASHER 3/8
51 P5851Z051 CUTTERHEAD 24" 4 BLADE 106 P5851Z106 HEX NUT 3/8"-16
51-1 P5851Z051-1 FLAT HEAD SCREW M6-1 X 16 107 P5851Z107 HEX BOLT 1/2-12 X 1-1/2
52 P5851Z052 PRESSURE BAR BRACKET 108 P5851Z108 LOCK WASHER 1/2
53 P5851Z053 PRESSURE BAR 109 P5851Z109 TABLE EDGE GUIDE
54 P5851Z054 PRESSURE SPRING LEFT 110 P5851Z110 CAP SCREW 1/4-20 X 1/2

-44- Professional Series Planers

G5851Z & G7213Z

REF PART # DESCRIPTION REF PART # DESCRIPTION

111 P5851Z111 TABLE GIB 168 P5851Z168 HUB MOUNTING PLATE
112 P5851Z112 HEX NUT 3/8"-16 169 P5851Z169 ARC HUB
113 P5851Z113 HEX BOLT 3/8-16 X 1-3/4 170 P5851Z170 LOCK HANDLE 1/2-12
114 P5851Z114 SCALE POINTER 171 P5851Z171 HANDLE 1/2-12
115 P5851Z115 CAP SCREW 1/4-20 X 3/8 172 P5851Z172 CAP SCREW 5/16-18 X 1
116 P5851Z116 HEX NUT 3/8"-16 173 P5851Z173 SET SCREW 3/8-16 X 3/8
117 P5851Z117 HEX BOLT 3/8-16 X 2-1/2 174 P5851Z174 FLAT WASHER 1/2
119 P5851Z119 HEX BOLT 5/16-18 X 1-1/4 175 P5851Z175 SET SCREW 5/16-18 X 3/8
120 P5851Z120 LOCK WASHER 5/16 176 P5851Z176 SET SCREW 5/16-18 X 1/4
121 P5851Z121 HEX BOLT 5/16-18 X 1 177 P5851Z177 FEED MOTOR 2HP 220V
122 P5851Z122 DUST BOOT 178 P5851Z178 BELT GUARD LABEL
123 P5851Z123 BALL BEARING 2904 179 P5851Z179 CONTROL PANEL
124 P5851Z124 HEX BOLT 5/16-18 X 1 180 P5851Z180 GRIZZLY NAMEPLATE 8W X 3.5H
125 P5851Z125 LOCK WASHER 5/16 181 P5851Z181 EMERGENCY STOP SWITCH
126 P5851Z126 MOTOR 5HP 220V 1PH 182 P5851Z182 ON SWITCH
127 P5851Z127 PULLEY 5" 183 P5851Z183 GRIZZLY NAME PLATE
128 P5851Z128 BELT A64 184 P5851Z184 MACHINE ID LABEL
129 P5851Z129 LEFT GUARD 185 P5851Z185 GREASE FITTING
131 P5851Z131 HEX BOLT 3/8-16 X 1-1/2 186 P5851Z186 DO NOT OPEN WARNING
132 P5851Z132 FLAT WASHER 3/8 187 P5851Z187 SAFETY GLASSES 2W X 3.3H
133 P5851Z133 LOCK WASHER 3/8 188 P5851Z188 READ MANUAL 2W X 3.3H
134 P5851Z134 HEX NUT 3/8"-16 189 P5851Z189 SET SCREW 1/4-20 X 1/4
135 P5851Z135 HEXAGON SCREW 190 P5851Z190 BED ROLLER BASE
136 P5851Z136 HEX NUT 3/8"-16 191 P5851Z191 DUST HOOD 24"
137 P5851Z137 HEX BOLT 5/16-18 X 1 192 P5851Z192 CHIPBREAKER SIDE PLATE
138 P5851Z138 LOCK WASHER 5/16 193 P5851Z193 HEX NUT 1/2"-13
139 P5851Z139 SET SCREW 1/4-20 X 3/8 194 P5851Z194 HEX BOLT 1/2-12 X 4
140 P5851Z140 SET SCREW 5/16-18 X 3/8 195 P5851Z195 FEED POWER SWITCH
142 P5851Z142 FLAT WASHER 1/2 196 P5851Z196 KNIFE SETTING GIB
143 P5851Z143 LOCK WASHER 5/16 197 P5851Z197 SUPPORT SHAFT
144 P5851Z144 HEX BOLT 5/16-18 X 1 198 P5851Z198 COVER
145 P5851Z145 ACORN NUT 1/2-12 199 P5851Z199 MOTOR ADJ BRACKET FOR FEED MOTOR
146 P5851Z146 HANDWHEEL 200 P5851Z200 KEY 8 X 10 X 64
147 P5851Z147 MOVEABLE HANDLE 201 P5851Z201 FLAT WASHER 3/8
148 P5851Z148 LOCK WASHER 5/16 202 P5851Z202 HEX BOLT 3/8-16 X 6
149 P5851Z149 HEX BOLT 5/16-18 X 1 203 P5851Z203 SPRING
150 P5851Z150 RIGHT GUARD 204 P5851Z204 V-BELT 4L460 (QTY 1)
151 P5851Z151 FLAT WASHER 1/4 205 P5851Z205 DEPTH GAUGE
152 P5851Z152 CAP SCREW 1/4-20 X 1/2 206 P5851Z206 KNIFE SETTING JIG
153 P5851Z153 CONTROL CASE PLASTIC V1.01.99 207 P5851Z207 WRENCH 17 X 19
154 P5851Z154 SUPPORT OF MOTOR COLUMN 208 P5851Z208 COMBO WRENCH 12/14MM
155 P5851Z155 MOUNTING BRACKET 209 P5851Z209 WRENCH 8 X 10
156 P5851Z156 SHAFT 210 P5851Z210 HEX WRENCH 4MM
157 P5851Z157 FIXED SHAFT 211 P5851Z211 LOCKING NUT
158 P5851Z158 SPACER 212 P5851Z212 SPACER
159 P5851Z159 SAFETY TOOTH 300 P5850Z300 MAGNETIC SWITCH ASSY
160 P5851Z160 CHAIN SHAFT 300 P7213Z300 MAGNETIC SWITCH 3-PH
161 P5851Z161 CHAIN 1/2 X 28" 300-1 P7213Z300-1 CONTACTOR - FEED MOTOR
162 P5851Z162 CHAIN 1/2" X 21 1/2" 300-2 P7213Z300-2 OVERLOAD RELAY - FEED MOTOR
163 P5851Z163 SPROCKET 14T 300-3 P7213Z300-3 CONTACTOR - CUTTERHEAD
164 P5851Z164 DOUBLE SPROCKET 14T 300-4 P7213Z300-4 OVERLOAD RELAY - CUTTERHEAD
165 P5851Z165 SPROCKET 14T 301 P5850Z301 FUSE HOLDER
166 P5851Z166 COLLAR 301-1 P5850Z301-1 FUSE 2A
167 P5851Z167 SHAFT 302 P5850Z180 INDICATOR LIGHT (220V)

Professional Series Planers -45-

WARRANTY AND RETURNS

Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from

the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,

negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty

and any and all warranties that may be implied by law, including any merchantability or fitness, for any par-

ticular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent

that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants.

In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and

any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.

We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special,

or consequential damages arising from the use of our products.

To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then

issue you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the

carton. We will not accept any item back without this number. Proof of purchase must accompany the

merchandise.

The manufacturers reserve the right to change specifications at any time because they constantly strive to

achieve better quality equipment. We make every effort to ensure that our products meet high quality and

durability standards and we hope you never need to use this warranty.

Please feel free to write or call us if you have any questions about the machine or the manual.

Thank you again for your business and continued support. We hope to serve you again soon.

-46- Professional Series Planers

WARRANTY CARD

Name _____________________________________________________________________________________

Street _____________________________________________________________________________________

City ______________________________________________________________ State________Zip_________

Phone Number_______________________E-Mail_______________________FAX________________________

MODEL #_______________________Serial#________________________Order #________________________

The following information is given on a voluntary basis. It will be used for marketing purposes to help us develop better products and services. Of course,

all information is strictly confidential.

1. How did you learn about us?

___Advertisement ___Friend
___Catalog ___World Wide Web

___Other__________________________________________________

2. Which of the following magazines do you subscribe to.

___American Woodworker ___Practical Homeowner
___Cabinetmaker ___Shop Notes
___Family Handyman ___Today’s Homeowner
___Fine Homebuilding ___WOOD
___Fine Woodworking ___Wooden Boat
___Home Handyman ___Woodshop News
___Journal of Light Construction ___Woodsmith
___Old House Journal ___Woodwork
___Popular Mechanics ___Woodworker
___Popular Science ___Woodworker’s Journal
___Popular Woodworking ___Workbench

___Other__________________________________________________

3. Which of the following woodworking/remodeling shows do you watch?

___Backyard America ___The New Yankee Workshop
___Home Time ___This Old House
___The American Woodworker ___Woodwright’s Shop

___Other__________________________________________________

4. What is your annual household income?

___$20,000-$29,999 ___$60,000-$69,999
___$30,000-$39,999 ___$70,000-$79,999
___$40,000-$49,999 ___$80,000-$89,999
___$50,000-$59,999 ___$90,000 +

5. What is your age group?

___20-29 ___50-59
___30-39 ___60-69
___40-49 ___70 +

6. How long have you been a woodworker?

___0 - 2 Years ___8 - 20 Years
___2 - 8 Years ___20+ Years

7. How would you rank your woodworking skills?

___Simple ___Advanced
___Intermediate ___Master Craftsman

8. What stationary woodworking tools do you own? Check all that apply.

___Air Compressor ___Panel Saw
___Band Saw ___Shaper
___Drill Press ___Power Feeder
___Drum Sander ___Radial Arm Saw
___Dust Collector ___Planer
___Horizontal Boring Machine ___Spindle Sander
___Jointer ___Table Saw
___Lathe ___Vacuum Veneer Press
___Mortiser ___Wide Belt Sander

___Other__________________________________________________

9. How many of your woodworking machines are Grizzly? _____________

10. Which benchtop tools do you own? Check all that apply.

___1" x 42" Belt Sander ___6" - 8" Grinder
___5" - 8" Drill Press ___Mini Lathe
___8" Table Saw ___10" - 12" Thickness Planer
___8" - 10" Bandsaw ___Scroll Saw
___Disc/Belt Sander ___Spindle/Belt Sander
___Mini Jointer

___Other__________________________________________________

11. How many of the machines checked above are Grizzly? ____________

12. Which portable/hand held power tools do you own? Check all that apply.

___Belt Sander ___Orbital Sander
___Biscuit Joiner ___Palm Sander
___Circular Saw ___Portable Planer
___Detail Sander ___Saber Saw
___Drill/Driver ___Reciprocating Saw
___Miter Saw ___Router

___Other__________________________________________________

13. What machines/supplies would you like Grizzly Industrial to carry?

_________________________________________________ _ _______

_________________________________________ ___ __ ___

_________________________________________

14. What new accessories would you like Grizzly Industrial to carry?

_________________________________________________ _ _______

_________________________________________ ___ __ ___

_________________________________________

15. What other companies do you purchase your tools and supplies from?

__________________________________________________________

__________________________________________________________

16. Do you think your purchase represents good value?

___Yes ___No

17. Would you recommend Grizzly Industrial to a friend?

___Yes ___No

18. Would you allow us to use your name as a reference for Grizzly customers
in your area? Note: We never use names more than three times.

___Yes ___No

19. Comments:_______________________________________________

__________________________________________________________

__________________________________________________________

__________________________________________________________

__________________________________________________________

CUT ALONG DOTTED LINE

Professional Series Planers -47-

FOLD ALONG DOTTED LINE

FOLD ALONG DOTTED LINE

Place

Stamp

Here

GRIZZLY INDUSTRIAL, INC.
P.O. BOX 2069
BELLINGHAM, WA 98227-2069

Send a Grizzly Catalog to a friend:

Name_______________________________

Street_______________________________

City______________State______Zip______

TAPE ALONG EDGES--PLEASE DO NOT STAPLE