Grizzly T33312 User guide

MODEL T33312
PANEL LIFTING CART
INSTRUCTIONS
For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com
Introduction
The Model T33312 Panel Lifting Cart transports and lifts unwieldy plywood and panels to the height of a workbench, table saw, etc. It has a capacity of 300 lbs. and four locking casters.
Figure 1. Model T33312.
—Button Head Cap Screw M8-1.25 x 16 ... 1 —Flat Washers 12mm
— Lock Nuts M12-1.75 ................................. 4
— Lock Nuts M8-1.25 ................................ 12
—Knob Bolts M8-1.25 x 20
A
E
................................ 4
........................ 2
B
C
D
F
Inventory
Loose Items (Figure 2) Qty
A. Lift Assembly .............................................. 1
Extension Spring 1.5 x 10 x 80 .................. 1
B.
Lock Lever .................................................. 1
C.
Swivel Lock Casters ................................... 4
D.
Stands ........................................................ 2
E.
Lower Cross Beams ................................... 2
F.
Upper Cross Beam ..................................... 1
G.
Hardware (Not Shown)
H.
—Hex Bolts M8-1.25 x 65 .......................... 8
—Hex Bolts M8-1.25 x 45
NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
.......................... 4
COPYRIGHT © AUGUST, 2022 BY GRIZZLY INDUSTRIAL, INC.
(FOR MODELS MFD. SINCE 07/22) #CS22426 PRINTED IN CHINA
***Keep for Future Reference***
G
Figure 2. Inventory.
Assembly
Tools Needed Qty
Wrenches or Sockets 13mm ............................. 2
Open-End Wrench 19mm
.................................. 1
V1.0 8.22
To assemble cart:
Attach (2) stands to (2) lower cross beams
1.
with (8) M8-1.25 x 65 hex bolts and M8-1.25 lock nuts (see Figure 3).
Stand
(1 of 2)
Lower
x 8
Cross Beam
(1 of 2)
4.
Lock casters to keep stand stationary in fol-
lowing steps.
Loosen (2) knob bolts, if installed, in stands
5.
enough to complete following step.
Slide lift assembly posts all the way into
6.
stands, as shown in Figure 5, then secure with knob bolts.
Lift
Assembly
x 2
Figure 3. Stands attached to lower cross beams.
2. Attach upper cross beam to stands with (4)
M8-1.25 x 45 hex bolts and M8-1.25 lock nuts (see Figure 4).
Attach (4) swivel lock casters to stands with
3.
(4) 12mm flat washers and M12-1.75 lock nuts (see Figure 4).
Upper
Cross Beam
x 4
x 4
Figure 5. Lift assembly installed on stands.
7.
Attach lock lever to lift assembly with M8-1.25
x 16 button head cap screw and extension spring, as shown in Figure 6.
Lock Lever
Extension
Spring
Figure 6. Lock lever and extension spring
installed.
Swivel Lock Caster
(1 of 4)
Figure 4. Upper cross beam and swivel lock
casters attached to stands.
-2-
Model T33312 (Mfd. Since 07/2 2)
Operation
The Model T33312 can be used to simply trans­port a panel from one location to another, to unload a panel from a truck or workbench, or to lift a panel to feed it onto a workbench, table saw, etc.
To operate cart:
Use lift bar to move lift frame to horizontal
1.
position (see Figure 7).
Note: Lock lever will lock lift frame position
once horizontal.
Loosen height lock knobs shown in Figure 7,
2.
adjust lift frame to desired height, then tighten lock knobs to secure.
4.
Lock casters to keep cart stationary.
5. Load panel onto lift frame, centering panel on cart (see Figure 9).
Panel
Figure 9. Panel centered on cart.
Lift Bar
Height
Lock Knob
(1 of 2)
Figure 7. Lift frame in horizontal position.
3. Lift lock lever to release lift frame, then return
frame to vertical position (see Figure 8).
Lock
Lever
Lift Frame
6.
Unlock casters.
7. Push cart to desired location, face cart and panel away from lifting loca­tion, then lock casters.
Move lift frame until lock lever locks it in
8.
horizontal position, then unload panel (see
Figure 10).
Figure 8. Lift frame in vertical position.
Model T33312 (Mfd. Since 07/2 2)
Figure 10. Unloading panel from cart.
-3-
T33312 Parts Breakdown & List
Please Note: We do our best to stock replacement parts whenever possible, but we cannot guarantee that all parts shown here
are available for purchase. Call
MODEL T33312
WARNING!
PANEL LIFTING CART
To reduce risk of serious personal injury when using cart:
1. Read and understand manual before using this cart.
2. Ensure cart is correctly set up before using.
3. Never stand or ride on cart.
4. Do not exceed maximum weight capacity of 300 lbs.
5. Keep load balanced to prevent tipping.
6. Do not lift or transport more than one panel at a time.
7. Set caster brakes when loading/unloading cart.
8. Avoid using on inclines or ramps that will cause loss of control.
Specifications
Date
Max. Weight Capacity: 300 lbs.
S/N
Horizontal Panel Height: 30"−42"
19
1
2
4
3
Weight: 38 lbs.
Mfd. for Grizzly in China
griz zly. com
20
5
21
T33 312
6
7
8
11
9
10
22
12
13
18
14
15
16
18
17
10
REF PART # DES CRIP TION REF PART # DES CRIP TION
1 PT33312001 LIFT FRAME 12 PT33312012 STAND 2 PT33312002 LOCK LEVER 13 PT33312013 HEX BOLT M8-1.25 X 45 3 PT33312003 EXTENSION SPRING 1.5 X 10 X 80 14 PT33312014 LOCK NUT M12-1.75 4 PT33312004 HEX BOLT M8-1.25 X 35 15 PT33312015 FLAT WASHER 12MM 5 PT33312005 BUTTON HD CAP SCR M8-1.25 X 16 16 PT33312016 HEX BOLT M8-1.25 X 65 6 PT33312006 SHOULDER SCREW M8-1.25 X 14, 10 X 13 17 PT33312017 CASTER 3", LOCKING SWIVEL 7 PT33312007 SHOULDER SCREW M8-1.25 X 13, 10 X 35 18 PT33312018 LOWER CROSS BEAM 14-15/16" 8 PT33312008 HEIGHT BRACKET 19 PT33312019 MACHINE ID LABEL 9 PT33312009 UPPER CROSS BEAM 15-7/8" 20 PT33312020 GRIZZLY.COM LABEL 10 PT33312010 LOCK NUT M8-1.25 21 PT33312021 MODEL NUMBER LABEL 11 PT33312011 KNOB BOLT M8-1.25 X 20, 5-LOBE, D37 22 PT33312022 TOUCH-UP P AI NT, GRI ZZL Y G REEN
(8 00) 523- 4777 or visit our online parts store at www.grizzly.com to check for availability.
-4-
BUY PARTS ONLINE AT GRIZZLY.CO M!
Scan QR code to visit our Parts Store.
Model T33312 (Mfd. Since 07/2 2)
Loading...