Page 1
To reduce your risk of
serious injury, read this
entire manual BEFORE
MODEL T32795
SHEARS SHARPENING JIG
FOR T32720 WET GRINDER
INSTRUCTIONS
For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com
Introduction
The Model T32795 Shears Sharpening Jig is
a fixture designed for sharpening scissors and
shears on the Model T32720 10" Wet Grinder.
using machine.
Inventory
Description Qty
A. Jig ............................................................... 1
Clamp ......................................................... 1
B.
Knob Bolts M6-1 x 22 ................................. 2
C.
A
B
C
Figure 2. Inventory.
Figure 1. Example of Model T32795 in use.
COPYRIGHT © JUNE, 2021 BY GRIZZLY INDUSTRIAL, INC.
NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
(FOR MODELS MFD. SINCE 07/21) #CS21970 PRINTED IN CHINA
NOTICE
If you cannot find an item on this list, carefully check around/inside the machine and
packaging materials. Often, these items get
lost in packaging materials while unpacking or they are pre-installed at the factory.
V1.0 6.21
Page 2
Using Jig
Wear personal protective equipment to
Keep hair, clothing, and
ing parts at all times.
Entanglement can result
in death, amputation, or
Attach the jig support to the tool rest on your
Model T32720 10" Wet Grinder to sharpen scissors, shears, and clippers.
Eye and face injuries and respiratory problems can occur while operating this tool.
4. Loosen (2) clamp knobs on clamp enough to
allow one blade of scissors or shears to slide
in (see Figure 4).
Loosen (2) lock knobs on clamp enough so
5.
they do not extend through upper portion of
clamp (see Figure 4).
reduce your risk from these hazards.
jewelry away from mov-
severe crushing injuries!
To use jig:
DISCONNECT GRINDER FROM POWER!
1.
2. Install tool rest in vertical position so it is
about 1" away from grinding wheel.
Slide jig onto tool rest and secure with (2)
3.
M6-1 x 22 knob bolts (see Figure 3).
Tool Rest
Lock Knob
(1 of 2)
Figure 4. Clamp components.
6.
Insert (1) blade of scissors or shears into
clamp, as shown in Figure 5, and tighten
clamp knob to secure.
Note: If blade extends to second triangle
clamp, tighten both clamp knobs.
Tighten lock knob to secure (see Figure 5).
7.
Note: If blade extends to second triangle
clamp, tighten both lock knobs.
Clamp Knob
(1 of 2)
Clamp Knob
(1 of 2)
Jig
Figure 3. Jig installed on tool rest.
-2-
x 2
Lock Knob
(1 of 2)
Triangle
Clamp
(1 of 2)
Figure 5. Example of scissor blade secured in
clamp.
Model T32795 (Mfd. Since 07/21)
Page 3
8. Rest clamp against rails of jig and grinding
wheel (see Figure 6).
Tilt scissor jig away from grinding wheel, con-
10.
nect grinder to power, and turn machine ON.
Adjust tool rest closer to or further from grind-
9.
ing wheel and angle of jig until beveled edge
of blade sits flat against grinding wheel (see
Figure 6).
Rails
Beveled
Edge
Sharpening
Jig
Scissor
Blade
Grinding Wheel
Figure 6. Adjusting angles for beveled edge of
scissor blade.
Use firm grip to return scissor blade to sur-
11.
face of grinding wheel to perform operation.
Use smooth stroking motion and even pressure with beveled edge of blade flat against
grinding wheel and against wheel rotation
(see Figure 7).
Figure 7. Example of grinding scissor blade.
Model T32795 (Mfd. Since 07/21)
-3-
Page 4
Loading...