Grizzly T32715 User guide

Download

Page 1

MODEL T32715

To reduce your risk of serious injury, read this entire manual BEFORE

Eye injury hazard! Always wear safety glasses when

TUBE BENDER SET

INSTRUCTIONS

For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com

Introduction

The T32715 Tube Bender Set is designed to bend most common tube sizes on a safe centerline radius. The set comes with

⁄8" round dies, as well as 3⁄4" and 1" square

and dies.

using machine.

using this machine.

⁄8", 1⁄2 ", 9⁄16", 5⁄8", 3⁄4",

Specifications

• Round Tube Capacity ........................3⁄8"–7⁄8"

• Square Tube Capacity .........................3⁄4"–1"

• Maximum Bending Angle ...................... 180°

• Maximum Bending Capacity .........18 Gauge

• Weight ................................................58 lbs.

Needed for Setup

• Safety Glasses ......................................1 Pr.

• Cleaner/Degreaser ..................... As Needed

• Disposable Shop Rags ............... As Needed

• Disposable Gloves ..................... As Needed

• Mounting Hardware .................... As Needed

• Open-End Wrench or Socket 22mm .......... 1

• Hex Wrench 3mm ....................................... 1

Figure 1. Model T32715 Tube Bender Set.

NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

(FOR MODELS MFD. SINCE 05/21) #CS21852 PRINTED IN CHINA

V1.05.21

Page 2

Another option is a "direct mount" (see example below) where the machine is secured directly to the workbench with lag screws and washers.

The base of this machine has mounting holes

Inventory

Description (Figure 2) Qty

A. Carrying Case ............................................ 1

Handle Assembly ....................................... 1

Square Die Set 1" ....................................... 1

Square Die Set 3⁄4" ..................................... 1

Round Die Set 7⁄8" ...................................... 1

Round Die Set 3⁄4" ...................................... 1

Round Die Set 5⁄8" ...................................... 1

Round Die Set 9⁄16" ..................................... 1

Round Die Set 1⁄2 " ...................................... 1

Round Die Set 3⁄8" ...................................... 1

Bending Arm Assembly .............................. 1

Base Assembly ........................................... 1

Round Roller 3⁄8" ......................................... 1

Round Roller 1⁄2 " ......................................... 1

Round Roller 9⁄16" ........................................ 1

Round Roller 5⁄8" ......................................... 1

Round Roller 3⁄4" ......................................... 1

Round Roller 7⁄8" ......................................... 1

S. Square Roller 1" ......................................... 1

Workbench Mounting

Number of Mounting Holes Dia.of Mounting Hardware Needed

that allow it to be fastened to a workbench or other mounting surface to prevent it from moving during operation and causing accidental injury or damage.

The strongest mounting option is a "Through Mount" (see example below) where holes are drilled all the way through the workbench—and hex bolts, washers, and hex nuts are used to secure the machine in place.

............................ 4

...........7⁄16"

Hex Bolt

Flat Washer

Figure 2. Inventory.

NOTICE

If you cannot find an item on this list, carefully check around/inside the machine and packaging materials. Often, these items get lost in packaging materials while unpacking or they are pre-installed at the factory.

Machine Base

Workbench

Flat Washer

Lock Washer

Hex Nut

Figure 3. "Through Mount" setup.

Lag Screw

Flat Washer

Machine Base

Workbench

-2-

Figure 4. "Direct Mount" setup.

T32715 (Mfd. Since 05/21)

Page 3

Cleanup

The unpainted surfaces of your machine are coated with a heavy-duty rust preventative that prevents corrosion during shipment and storage. This rust preventative works extremely well, but it will take a little time to clean.

Be patient and do a thorough job cleaning your machine. The time you spend doing this now will give you a better appreciation for the proper care of your machine's unpainted surfaces.

There are many ways to remove this rust preventative, but the following steps work well in a wide variety of situations. Always follow the manufacturer’s instructions with any cleaning product you use and make sure you work in a well-ventilated area to minimize exposure to toxic fumes.

Before cleaning, gather the following:

• Disposable rags

• Cleaner/degreaser (WD•40 works well)

• Safety glasses & disposable gloves

• Plastic paint scraper (optional)

Basic steps for removing rust preventative:

2. Coat the rust preventative with a liberal

amount of cleaner/degreaser, then let it soak

off easily. If you have a plastic paint scraper, scrape off as much as you can first, then wipe

then coat all unpainted surfaces with a quality

Assembly

The machine must be fully assembled before it can be operated. Before beginning the assembly process, refer to Needed for Setup and gather all listed items. To ensure the assembly process goes smoothly, first clean any parts that are covered or coated in rust preventative.

Wear safety glasses during the entire setup process!

Put on safety glasses.

for 5–10 minutes.

Wipe off the surfaces. If your cleaner/degreas-

er is effective, the rust preventative will wipe

To assemble machine:

Mount base assembly to stable work-

1. bench surface as described in Workbench Mounting on Page 2.

Note: For easiest bending, straight ridge on

base should face left, and base should be no more than 5" from front edge of workbench (see Figure 5).

Straight

Ridge

5" or Less

Base Assembly

off the rest with the rag.

Repeat Steps 2–3 as necessary until clean,

metal protectant to prevent rust.

NOTICE

Avoid harsh solvents like acetone or brake parts cleaner that may damage painted surfaces. Always test on a small, inconspicuous location first.

T32715 (Mfd. Since 05/21)

Figure 5. Base correctly positioned on

workbench.

-3-

Page 4

2. Install desired die on spindle on base assembly (see Figure 6).

Note: Tube seat should face opposite side of

ridge noted in Step 1 (see Figure 6).

Spindle

Tube Seat

Die

Figure 6. Die installed on spindle.

Remove roller hex nut and flat washer on

3. bending arm assembly shown in Figure 7.

4. Install roller that matches size of die from Step 2 and secure with T-bolt, flat washer,

and hex nut (see Figure 8).

Note: 1" square roller is used for both 1" and

⁄4" square dies.

Roller

Figure 8. Roller installed on bending arm.

5. Install bending arm on spindle, on top of die

from Step 2 (see Figure 9).

Bending Arm

Assembly

Figure 7. Location of roller hex nut and flat

washer.

Note: If bending arm does not seat against

die on spindle, loosen leadscrew nut to create clearance (see Figure 9).

Spindle

Bending Arm

Leadscrew

Die

Nut

Figure 9. Bending arm installed on spindle.

-4-

T32715 (Mfd. Since 05/21)

Page 5

6. Install inner handle on bending arm by sliding

Eye injury hazard! Always wear safety glasses when

over leadscrew, and secure by tightening set screws (see Figure 10).

Note: Inner handle is stored inside outer

handle in carrying case.

Leadscrew

To operate:

Spread thin film of light machine oil on appro-

priate die and roller for operation.

Install die and roller (see Assembly begin-

ning on Page 3).

Loosen handle set screws from Step 6

of Assembly to adjust leadscrew nut until workpiece can fit between roller and die (see Figure 11).

Insert workpiece between die and roller until

end is through tube seat, then tighten leadscrew nut until workpiece is supported (see Figure 11).

x 2

Inner Handle

Figure 10. Inner handle installed and secured on

bending arm.

Note: Once set screws are tightened, lead-

screw nut cannot be adjusted.

Install outer handle on inner handle.

Operation

The Model T32715 is capable of bending round tube between tube between

⁄8"–7⁄8" in diameter, and square

⁄4"–1" in diameter.

using this machine.

Roller

Die

Leadscrew

Nut

Workpiece

Figure 11. Workpiece ready for bending.

5. Tighten handle set screws to secure handle.

Crushing hazard! Always keep hands clear when using this machine.

Only bend stock that falls within bending capacity of this machine. Stock thicker than 18 gauge will damage machine when bent.

Items Needed Qty

Light Machine Oil............................... As Needed

T32715 (Mfd. Since 05/21)

Pull handle to bend tube until desired angle is

achieved.

-5-

Page 6

Parts Breakdown & List

REF P ART # DES CRIPTION REF P ART # DES CRIPTION

Please Note: We do our best to stock replacement parts whenever possible, but we cannot guarantee that all parts shown here are available for purchase. Call (800) 523 - 4777 or visit our online parts store at www.grizzly.com to check for availability.

T32715

Date

Serial Number

Mfd. for Grizzly in China

1 PT32715001 BASE 33 PT32715033 DIE 9/16" ROUND 2 PT32715002 SPINDLE 34 PT32715034 DI E 5/ 8" ROUND 4 PT32715004 ROLLER SEAT 35 PT32715035 DI E 3/ 4" ROUND 5 PT32715005 LEADSCREW TR10-4 36 PT32715036 DI E 7/ 8" RO UND 6 PT32715006 LEA DSCREW NUT TR1 0-4 37 PT32715037 DIE 3/4" SQUARE 7 PT32715007 HANDLE 38 PT32715038 DIE 1" SQUARE 8 PT32715008 OUTER HA NDLE 41 PT32715041 TUBE SEAT 3/8" ROUND 9 PT32715009 SET SCREW M6-1 X 10 42 PT32715042 TUBE SEAT 1/2" ROUND 10 PT32715010 BE NDI NG ARM 43 PT32715043 TUBE SEAT 9/ 16" ROUND 11 PT32715011 SHOULDER BOLT M14-2 X 20, 14 X 72 44 PT32715044 TUBE SEAT 5/8" ROUND 13 PT32715013 HEX NUT M14- 2 45 PT32715045 TUBE SEAT 3/4" ROUND 16 PT32715016 FLAT WASHER 14MM 46 PT32715046 TUBE SEAT 7/8" ROUND 17 PT32715017 SET SCREW M6-1 X 8 47 PT32715047 TUBE SEAT 3/4" SQUARE 21 PT32715021 ROLLER 3/ 8" ROUND 48 PT32715048 TUBE SEAT 1" SQUARE 22 PT32715022 ROLLER 1/ 2" ROUND 51 PT32715051 HEX BOLT M8-1.25 X 15 23 PT32715023 ROLLER 9/ 16" ROUND 52 PT32715052 HEX BOLT M10-1.5 X 20 24 PT32715024 ROLLER 5/ 8" ROUND 53 PT32715053 HEX BOLT M12-1.75 X 20 25 PT32715025 ROLLER 3/ 4" ROUND 54 PT32715054 HEX BOLT M16-2 X 25 26 PT32715026 ROLLER 7/ 8" ROUND 55 PT32715055 GRIZZLY.COM LABEL 27 PT32715027 ROLLER 1" SQUARE 56 PT32715056 MACHINE ID LABEL 31 PT32715031 DI E 3/ 8" ROUND 57 PT32715057 TOUCH- UP PA I NT, GRI ZZLY GRE EN 32 PT32715032 DI E 1/ 2" ROUND

-6-

T32715 (Mfd. Since 05/21)

Page 7

WARRANTY & RETURNS

Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty and any and all warranties that may be implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants. In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.

We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special, or consequential damages arising from the use of our products.

The manufacturers reserve the right to change specifications at any time because they constantly strive to achieve better quality equipment. We make every effort to ensure that our products meet high quality and durability standards and we hope you never need to use this warranty.

In the event you need to use this warranty, contact us by mail or phone and give us all the details. We will then issue you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the carton. We will not accept any item back without this number. Proof of purchase must accompany the merchandise.

Please feel free to write or call us if you have any questions about the machine or the manual.

Thank you again for your business and continued support. We hope to serve you again soon.

To you can applicable information for

take advantage of this warranty, you must register it at https://www.grizzly.com/forms/warranty, or

scan the QR code below to be automatically directed to our warranty registration page. Enter all

the product.

WARRANTY

Page 8