Grizzly T32006 User guide

Download

MODEL T32006

MINI BENCHTOP DRILL PRESS

OWNER'S MANUAL

(For models manufactured since 01/20)

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE

OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.

#CS20890 PRINTED IN CHINA

V1.03.20

This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators.

Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death.

The owner of this machine/tool is solely responsible for its safe use. This responsibility includes but is not limited to proper installation in a safe environment, personnel training and usage authorization, proper inspection and maintenance, manual availability and comprehension, application of safety devices, cutting/sanding/grinding tool integrity, and the usage of personal protective equipment.

The manufacturer will not be held liable for injury or property damage from negligence, improper training, machine modifications or misuse.

Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• Lead from lead-based paints.

• Crystalline silica from bricks, cement and other masonry products.

• Arsenic and chromium from chemically-treated lumber.

Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: Work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

SECTION 1: SAFETY

For Your Own Safety Read Instruction Manual

Before Operating This Equipment

The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures.

Indicates an imminent hazardous situation which, if not avoided, WILL result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury.

Indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury. It may also be used to alert against unsafe practices.

NOTICE

This symbol is used to alert the user to useful information about proper operation of the equipment.

Safety Instructions for Power Tools

OWNER’S MANUAL. Read and under-

stand this owner’s manual BEFORE using machine.

TRAINED OPERATORS ONLY. Untrained operators have a higher risk of being hurt or killed. Only allow trained/supervised people to use this power tool. When tool is not being used, disconnect power, and store in out-of-reach location to prevent unauthorized use—especially around children. Make workshop kid proof!

DANGEROUS ENVIRONMENTS. Do not use tools in areas that are wet, cluttered, or have poor lighting. Operating tools in these areas greatly increases risk of accidents and injury.

Model T32006 (Mfd. Since 01/20) -3-

MENTAL ALERTNESS REQUIRED. Full mental alertness is required for safe operation of power tools. Never operate under the influence of drugs or alcohol, when tired, or when distracted.

DISCONNECT POWER FIRST. Always disconnect tool from power supply BEFORE making adjustments, changing tooling, or ser vicing machine. This prevents an injury risk from uninten ded start up or contact with live electrical components.

EYE PROTECTION. Always wear ANSIapproved safety glasses or a face shield when operating or observing machinery to reduce the risk of eye injury or blindness from flying particles. Everyday eyeglasses are not approved safety glasses.

ELECTRICAL SAFETY. Tool plug must

If at

match outlet. Double-insulated tools have a polarized plug (one blade is wider than the other), which must be plugged into a polarized outlet. Never modify plug. Do not use adapter for grounded tools. Use a ground fault circuit interrupter if operation is unavoidable in damp locations. Avoid touching grounded surfaces when operating tool.

WEARING PROPER APPAREL. Do not wear clothing, apparel or jewelry that can become entangled in moving parts. Always tie back or cover long hair. Wear non-slip footwear to avoid accidental slips, which could cause loss of workpiece control. Wear hard hat as needed.

HAZARDOUS DUST. Dust created while using tools may cause cancer, birth defects, or long-term respiratory damage. Be aware of dust hazards associated with each workpiece material, always wear a NIOSH-approved respirator, and connect tool to an appropriate dust collection device to reduce your risk.

HEARING PROTECTION. Always wear hearing protection when operating or observing loud machinery. Extended exposure to this noise without hearing protection can cause permanent hearing loss.

REMOVE ADJUSTING TOOLS. Never leave adjustment tools, chuck keys, wrenches, etc. in or on tool—especially near moving parts. Verify removal before starting!

INTENDED USAGE. Only use tool for its intended purpose. Never modify or alter tool for a purpose not intended by the manufacturer or serious injury or death may result!

AWKWARD POSITIONS. Keep proper footing and balance at all times when operating tool. Do not overreach! Avoid awkward hand positions that make tool control difficult or increase the risk of accidental injury.

SAFE HANDLING. Firmly grip tool. To avoid accidental firing, do not keep finger on switch or trigger while carrying.

FORCING TOOLS.. Use right tool for job, and do not force it. It will do job safer and better at rate for which it was designed.

SECURING WORKPIECE. When required, use clamps or vises to secure workpiece. This protects hands and frees both of them to operate tool.

GUARDS & COVERS. Guards and covers reduce accidental contact with moving parts or flying debris. Ensure they are properly installed, undamaged, and working correctly.

CHILDREN & BYSTANDERS. Keep children and bystanders at a safe distance from the work area. Stop using tool if they become a distraction.

USE RECOMMENDED ACCESSORIES. Consult this manual or manufacturer for recommended accessories. Using improper accessories will increase risk of serious injury.

MAINTAIN WITH CARE. Keep cutting tool edges sharp and clean. Follow all maintenance instructions and lubrication schedules to keep tool in good working condition. A tool that is improperly maintained could malfunction, leading to serious personal injury or death. Only have tool serviced by qualified servicepersonnel using matching replacement parts.

CHECK DAMAGED PARTS. Regularly inspect tool for any condition that may affect safe operation. Immediately repair or replace damaged or mis-adjusted parts before operating tool.

MAINTAIN POWER CORDS. When disconnecting cord-connected tools from power, grab and pull the plug—NOT the cord. Carrying or pulling the cord may damage wires inside. Do not handle cord/ plug with wet hands. Avoid cord damage by keeping it away from heated surfaces, high traffic areas, harsh chemicals, sharp edges, moving parts, and wet/damp locations. Damaged cords increase risk of electrocution.

UNATTENDED OPERATION. Never leave tool running while unattended. Turn tool OFF and ensure all moving parts completely stop before walking away.

EXPERIENCING DIFFICULTIES.

any time you experience difficulties performing the intended operation, stop using the machine! Contact our Technical Support at (570) 546-9663.

Model T32006 (Mfd. Since 01/20)-4-

Additional Safety for Drill Presses

Serious injury or death can occur from getting clothing, jewelry, or long hair entangled in rotating spindle or bit/cutting tool. Contact with rotating bit/cutting tool can result in severe cuts or amputation of fingers. Flying metal chips, broken bits /cutting tools, unsecured workpieces, chuck keys, or other adjustment tools thrown from rotating spindle can strike nearby operator or bystanders with deadly force or cause eye injuries /blindness. To reduce the risk of these hazards, operator and bystanders MUST completely heed hazards and warnings below.

EYE/FACE/HAND PROTECTION.

Flying chips created by drilling can cause eye injuries or blindness. Always wear a face shield in addition to safety glasses. Always keep hands and fingers away from drill bit/cutting tool. Avoid awkward hand positions, where sudden slip could cause hand to move into bit/cutting tool.

AVOIDING ENTANGLEMENT. DO NOT wear loose clothing, gloves, or jewelry. Tie back long hair. Keep all guards in place and secure. Always allow spindle to stop on its own. DO NOT stop spindle using your hand or any other object.

REMOVING ADJUSTMENT TOOLS. Chuck key, wrenches, and other tools left on tool can become deadly projectiles when spindle is started. Remove all loose items or tools used on spindle immediately after use.

CORRECT SPINDLE SPEED. Using wrong spindle speed or feed rate can cause bits/cutting tools to break and strike operator or bystanders. Follow recommended speeds and feeds for each size/type of bit/cutting tool and workpiece material.

SECURING BIT/CUTTING TOOL. Firmly secure bit/cutting tool in chuck so it cannot fly out of spindle during operation or startup.

DRILLING PREPARATION. To avoid loss of drilling control or bit breakage, only drill into flat surface that is approximately perpendicular to bit. Clear table of all objects before starting spindle. Never start spindle with bit pressed against workpiece.

SECURING HEADSTOCK ON COLUMN. To avoid loss of control leading to bit breakage or accidental contact with tool/ bit, tighten headstock lock before operating drill press.

WORKPIECE CONTROL. An unsecured workpiece may unexpectedly shift, spin out of control, or be thrown if bit/cutting tool "grabs" during operation. Clamp workpiece to table or in table-mounted vise, or brace against column to prevent rotation. NEVER hold workpiece by hand during operation. NEVER start tool with bit/cutting tool touching workpiece; allow spindle to gain full speed before drilling.

INSPECTING BIT/CUTTING TOOL. Damaged bits/cutting tools may break apart during operation and hit operator or bystanders. Dull bits/cutting tools increase cutting resistance and are more likely to grab and spin/throw workpiece. Always inspect bits/cutting tools for sharpness, chips, or cracks before each use. Replace dull, chipped, cracked bits/cutting tools immediately.

No list of safety guidelines can be complete. Every shop environment is different. Always consider safety first, as it applies to your individual working conditions. Use this and other machinery with caution and respect. Failure to do so could result in serious personal injury, damage to equipment or poor work results.

Model T32006 (Mfd. Since 01/20) -5-

SECTION 2: INTRODUCTION

Foreword

We are proud to offer this manual with your new drill press! We've made every effort to be exact with the instructions, specifications, drawings, and photographs of the drill press we used when writing this manual. However, sometimes we still make an occasional mistake.

Also, owing to our policy of continuous improvement, your drill press may not exactly match the manual. If you find this to be the case, and the difference between the manual and drill press leaves you in doubt, check our website for the latest manual update or call technical support for help.

For your convenience, we post all available manuals and manual updates for free on our website at www.grizzly.com. Any updates to your model of drill press will be reflected in these documents as soon as they are complete.

Contact Info

We stand behind our machines and tools. If you have any service questions, parts requests or general questions about the machine, please call or write us at the location listed below.

Grizzly Technical Support

1815 W. Battlefield

Springfield, MO 65807

Phone: (570) 546 -9663

E-Mail: techsupport@grizzly.com

We want your feedback on this manual. If you can take the time, please email or write to us at the address below and tell us how we did:

Grizzly Industrial, Inc.

C/O Technical Documentation Manager

P.O. Box 2069

Bellingham, WA 98227-2069

Email: manuals@grizzly.com

Like all machinery there is potential danger when operating this tool. Accidents are frequently caused by lack of familiarity or failure to pay attention. Use this tool with respect and caution to decrease the risk of operator injury. If normal safety precautions are overlooked or ignored, serious personal injury may occur.

Model T32006 (Mfd. Since 01/20)-6-

Machine Data Sheet

Drill Chuck Size.............................................................................................................................. 1/32 - 1/4 in.

MACHINE DATA

SHEET

Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901

MODEL T32006 VARIABLE‐SPEED MINI BENCHTOP DRILL

PRESS

Product Dimensions:

Weight................................................................................................................................................................ 11 lbs.

Width (side-to-side) x Depth (front-to-back) x Height............................................................................. 7 x 10 x 15 in.

Footprint (Length x Width)......................................................................................................................... 9-1/2 x 7 in.

Shipping Dimensions:

Type..................................................................................................................................................... Cardboard Box

Content........................................................................................................................................................... Machine

Weight................................................................................................................................................................ 12 lbs.

Length x Width x Height....................................................................................................................... 21 x 13 x 18 in.

Electrical:

Power Requirement........................................................................................................... 120V, Single-Phase, 60 Hz

Full-Load Current Rating..................................................................................................................................... 0.95A

Minimum Circuit Size.............................................................................................................................................. 15A

Connection Type....................................................................................................................................... Cord & Plug

Power Cord Included.............................................................................................................................................. Yes

Power Cord Length................................................................................................................................................. 6 ft.

Power Cord Gauge......................................................................................................................................... 18 AWG

Plug Included.......................................................................................................................................................... Yes

Included Plug Type................................................................................................................................................ 5-15

Switch Type.................................................................................................................................. Variable-Speed Dial

Motors:

Main

Horsepower............................................................................................................................................. 1/8 HP

Phase............................................................................................................................................ Single-Phase

Amps......................................................................................................................................................... 0.95A

Speed........................................................................................................................................... 0 - 5000 RPM

Type..................................................................................................................................................... Universal

Power Transfer ............................................................................................................................................ Belt

Bearings..................................................................................................... Shielded & Permanently Lubricated

Main Specifications:

Operation Information

Swing..................................................................................................................................................... 8-3/4 in.

Spindle Taper............................................................................................................................................... B10

Spindle Travel........................................................................................................................................... 7/8 in.

Max. Distance From Spindle to Column................................................................................................ 4-3/8 in.

Max. Distance From Spindle to Table................................................................................................... 6-1/2 in.

Number of Spindle Speeds................................................................................................................... Variable

Range of Spindle Speeds............................................................................................................. 0 - 5000 RPM

Drilling Capacity (Mild Steel)................................................................................................................... 3/16 in.

Drill Chuck Type........................................................................................................................ B10 Key Chuck

Spindle Information

Distance From Spindle to Base............................................................................................................. 6-1/2 in.

Quill Diameter....................................................................................................................................... 1.200 in.

Table Information

Table Swing.......................................................................................................................................... 360 deg.

Table Swivel Around Center................................................................................................................. 360 deg.

Table Swivel Around Column............................................................................................................... 360 deg.

Max. Movement of Work Table.............................................................................................................. 6-1/2 in.

Table Length.......................................................................................................................................... 6-3/4 in.

Table Width........................................................................................................................................... 6-3/4 in.

Table Thickness........................................................................................................................................ 1/8 in.

Vertical Table Travel............................................................................................................................... Manual

Model T32006 (Mfd. Since 01/20) -7-

Identification

Become familiar with the names and locations of the controls and features shown below to better understand the instructions in this manual.

Downfeed

Belt Cover

Handle

Variable-Speed ON/OFF Switch

Spindle

Chuck

For Your Own Safety Read Instruction Manual Before Operating Drill Press a) Wear eye protection. b) Do not wear gloves, necktie, or loose clothing. c) Clamp workpiece or brace against column to prevent rotation. d) Use recommended speed for drill accessory and workpiece material.

Depth Stop

Headstock

Lock Handle

Column

Tab l e

Model T32006 (Mfd. Since 01/20)-8-

Controls &

Components

To reduce your risk of serious injury, read th is entire manual BEFORE using machine.

Refer to Figures 1–2 and the following descriptions to become familiar with the basic controls of this tool.

A. Chuck: Accepts bits with a diameter

between 1⁄32" and 1⁄4".

C. Downfeed Handle: Moves spindle

down when pulled down. Spindle automatically returns to top position when released.

D. Variable-Speed ON/OFF Switch: Turn

clockwise to turn motor ON and select desired speed. Turn counterclockwise to lower speed and turn motor OFF.

E. Headstock Lock Handle: Locks head-

stock in position on column.

B. Depth Stop: Indicates and controls

drilling depth.

Figure 1. Location of chuck.

Figure 2. Headstock controls.

Model T32006 (Mfd. Since 01/20) -9-

SECTION 3: POWER SUPPLY

Availability

Before installing the tool, consider the availability and proximity of the required power supply circuit. If an existing circuit does not meet the requirements for this tool, a new circuit must be installed. To minimize the risk of electrocution, fire, or equipment damage, installation work and electrical wiring must be done by an electrician or qualified service personnel in accordance with all applicable codes and standards.

Electrocution, shock, fire or damage to equipment may occur if tool is not properly grounded and connected to power supply.

Full-Load Current Rating

The full-load current rating is the amperage a tool draws at 100% of the rated output power. On machines with multiple motors, this is the amperage drawn by the largest motor or sum of all motors and electrical devices that might operate at one time during normal operations.

Full-Load Current Rating

The full-load current is not the maximum amount of amps that the tool will draw. If the tool is overloaded, it will draw additional amps beyond the full-load rating. If the tool is overloaded for a sufficient length of time, damage, overheating, or fire may result— especially if connected to an undersized circuit. To reduce the risk of these hazards, avoid overloading the tool during operation and make sure it is connected to a power supply circuit that meets the requirements in the following section.

.................. 0.95A

Serious injury could occur if you connect tool to power before completing setup process. DO NOT connect to power until instructed later in this manual.

120V Circuit Requirements

This tool is prewired to operate on a power supply circuit that has a verified ground and meets the following requirements:

Voltage ......................... 110V, 115V, 120V

Cycle ................................................ 60 Hz

Phase .................................. Single-Phase

Power Supply Circuit ................15 Amps

A power supply circuit includes all electrical equipment between the breaker box or fuse panel in the building and the tool. The power supply circuit used for this tool must be sized to safely handle the full-load current drawn from the tool for an extended period of time. (If this tool is connected to a circuit protected by fuses, use a time delay fuse marked D.)

For your own safety and protection of property, consult an electrician if you are unsure about wiring practices or electrical codes in your area.

Note: The circuit requirements listed in

this manual apply to a dedicated circuit— where only one tool or machine will be running at a time. If this tool will be connected to a shared circuit where multiple machines will be running at the same time, consult a qualified electrician to ensure that the circuit is properly sized for safe operation.

Model T32006 (Mfd. Since 01/20)-10-

Grounding & Plug Requirements

it will not fit the outlet, have a qualified electrician install the proper outlet with a

This tool MUST be grounded. In the event of certain malfunctions or breakdowns, grounding reduces the risk of electric shock by providing a path of least resistance for electric current.

This tool is equipped with a power cord that has an equipment-grounding wire and a grounding plug. Only insert plug into a matching receptacle (outlet) that is properly installed and grounded in accordance with all local codes and ordinances. DO NOT modify the provided plug!

GROUNDED

5-15 RECEPTACLE

Grounding Pin

5-15 PLUG

Neutral Hot

Figure 3. Typical 5-15 plug and

receptacle.

Improper connection of the equipmentgrounding wire can result in a risk of electric shock. The wire with green insulation (with or without yellow stripes) is the equipment-grounding wire. If repair or replacement of the power cord or plug is necessary, do not connect the equipmentgrounding wire to a live (current carrying) terminal.

Check with a qualified electrician or service personnel if you do not understand these grounding requirements, or if you are in doubt about whether the tool is properly grounded. If you ever notice that a cord or plug is damaged or worn, disconnect it from power, and immediately replace it with a new one.

Extension Cords

We do not recommend using an extension cord with this tool. If you must use an extension cord, only use it if absolutely necessary and only on a temporary basis.

Extension cords cause voltage drop, which can damage electrical components and shorten motor life. Voltage drop increases as the extension cord size gets longer and the gauge size gets smaller (higher gauge numbers indicate smaller sizes).

Two-prong outlets do not meet the grounding requirements for this machine. Do not modify or use an adapter on the plug provided—if

verified ground.

Model T32006 (Mfd. Since 01/20) -11-

SHOCK HAZARD!

Any extension cord used with this toolmust be in good condition and contain a ground wire and matching plug/receptacle. Additionally, it must meet the following size requirements:

Minimum Gauge Size ................. 16 AWG

Maximum Length ............................. 50 ft.

SECTION 4: SETUP

Unpacking

You r tool was carefully packaged for safe transportation. Remove the packaging materials from around your tool and inspect it. If you discover the tool is damaged, please immediately call Customer

Service at (570) 546-9663 for advice.

Save the containers and all packing materials for possible inspection by the carrier or its agent. Otherwise, filing a freight claim can be difficult.

When you are completely satisfied with the condition of your shipment, inventory the contents.

If any non-proprietary parts are missing (e.g., a nut or a washer), we will gladly replace them; or for the sake of expediency, replacements can be obtained at your local hardware store.

Needed for Setup

The following items are needed, but not included, for setup/assembly of this tool.

Description Qty.

Safety Glasses ................................... 1 Pr.

Inventory

Inventory (Figure 4)

A. Headstock Assembly .........................1

B. Column ...............................................1

C. Downfeed Handle ..............................1

D. Chuck Key ..........................................1

E. Hex Wrenches 2, 2.5, 4mm ........ 1 Ea.

F. Table ..................................................1

This tool presents serious injury hazards to untrained users. Read through this entire manual to become familiar with the controls and operations before starting the tool!

If you cannot find an item on this list, carefully check around/inside the tool and packaging materials. Often, these items get lost in packaging materials while unpacking or they are pre-installed at the factory.

Model T32006 (Mfd. Since 01/20)-12-

Figure 4. Inventory.

Cleanup

Basic steps for cleaning:

1. Put on safety glasses.

The unpainted surfaces of your machine are coated with a heavy-duty rust preventative that prevents corrosion during shipment and storage. This rust preventative works extremely well, but it will take a little time to clean.

Be patient and do a thorough job cleaning your tool. The time you spend doing this now will give you a better appreciation for the proper care of your tool's unpainted surfaces.

There are many ways to remove this rust preventative, but the following steps work well in a wide variety of situations. Always follow the manufacturer's instructions with any cleaning product you use and make sure you work in a well-ventilated area to minimize exposure to toxic fumes.

Before cleaning, gather the following:

• Disposable rags

• Cleaner/degreaser (WD-40 works well)

• Safety glasses & disposable gloves

• Plastic paint scraper (optional)

2. Coat rust preventative with liberal amount of cleaner/degreaser, then let it soak for 5–10 minutes.

3. Wipe off surfaces. If cleaner/degreaser is effective, rust preventative will wipe off easily.

4. Repeat Steps 2–3 until clean, then coat all unpainted surfaces with a quality metal protectant to prevent rust.

Avoid harsh solvents like acetone or brake parts cleaner that may damage painted surfaces.

Model T32006 (Mfd. Since 01/20) -13-

Assembly

This tool must be fully assembled before it can be operated. Before beginning the assembly process, refer to Needed for Setup and gather all listed items. To ensure the assembly process goes smoothly, first clean any parts that are covered or coated in heavy-duty rust preventative (if applicable).

To assemble tool:

1. Insert column into table on a flat, stable

surface (see Figure 5).

Note: If column will not fit in table,

remove headstock from column, place a block of wood over column, use a small hammer to tap column into table, then re-install headstock.

2. Tighten pre-installed set screw to secure column in table (see Figure 5).

3. Thread downfeed handle into downfeed pinion gear, as shown in Figure 6.

Downfeed

Handle

Downfeed

Pinion Gear

Figure 6. Downfeed handle installed in

downfeed pinion gear.

Table

Column

Figure 5. Location of set screw that

secures column in table.

Model T32006 (Mfd. Since 01/20)-14-

Test Run

To test run tool:

1. Clear away all setup/adjustment tools.

Once assembly is complete, test run the tool to ensure it is properly connected to power and safety components are working properly.

If you find an unusual problem during the test run, immediately stop the tool, disconnect it from power, and fix the problem BEFORE operating the tool again. The Troubleshooting table in the SERVICE section of this manual can help.

The Test Run consists of verifying the following: 1) The motor powers up and runs correctly.

Serious injury or death can result from using tool BEFORE understanding its controls and related safety information. DO NOT operate, or allow others to operate, tool until information is understood.

DO NOT start tool until all preceding setup instructions have been performed. Operating an improperly set up tool may result in malfunction or unexpected results that can lead to serious injury, death, or tool/ property damage.

2. Turn variable-speed dial all the way

counterclockwise (see Figure 7).

Variable-Speed

ON/OFF Dial

Figure 7. Location of variable-speed ON/

OFF dial.

. Connect tool to power supply.

4. Verify motor operation by slowly

turning variable-speed dial clockwise to turn tool ON. Rotate dial through its range of motion to test variable-speed function. Motor should run smoothly and without unusual problems or noises.

5. Turn variable-speed dial all the way counterclockwise to turn tool OFF.

Congratulations. Test run is complete.

Model T32006 (Mfd. Since 01/20) -15-

SECTION 5: OPERATIONS

Due to the generic nature of this overview, it is not intended to be an instructional

To reduce your risk of serious injury, read this entire manual BEFORE using tool.

guide. To learn more about specific operations, read this entire manual, seek additional training from experienced machine operators, and do additional research outside this manual by reading "how-to" books, trade magazines, or websites.

To reduce risk of eye or face injury from flying chips, always wear safety glasses and a face shield when operating this tool.

If you are not experienced with this type of tool, WE STRONGLY RECOMMEND that you seek additional training outside of this manual. Read books/magazines or get formal training before beginning any projects. Regardless of the content in this section, Grizzly Industrial will not be held liable for accidents caused by lack of training.

Operation Overview

The purpose of this overview is to provide the novice tool operator with a basic understanding of how the tool is used during operation, so the tool controls/components discussed later in this manual are easier to understand.

To complete a typical operation, the operator does the following:

1. Examines workpiece to make sure it is

suitable for drilling.

2. Put on required safety glasses and face shield.

3. Firmly secures workpiece to table using vise or clamp.

4. Installs correct drill bit or cutting tool for operation.

5. Adjusts headstock to correct height, then locks it in place.

6. Connects tool to power, and turns tool ON.

7. Selects appropriate spindle speed.

8. Performs drilling operation.

9. When finished, turns tool OFF and dis-

connects it from power.

Model T32006 (Mfd. Since 01/20)-16-

Installing/

Removing Bits

Any drill bit you install in the chuck must be tight enough that it will not come loose during operation.

To install/remove bit:

DISCONNECT TOOL FROM POWER!

2. Open drill chuck wide enough to

release bit and accept new bit shank.

3. Insert bit as far as possible into chuck WITHOUT allowing chuck jaws to touch fluted portion of bit, then handtighten chuck (see Figure 8).

To adjust headstock position:

1. DISCONNECT TOOL FROM POWER!

While holding headstock, loosen head-

stock lock handle shown in Figure 9.

Headstock

Lock Handle

Figure 9. Headstock lock handle location.

3. Adjust headstock to desired position,

then tighten lock handle to secure.

Note: Make sure small bits are not

trapped between edges of two jaws; if they are, re-install drill bit or it will not be secure enough to use for drilling.

Tighten chuck firmly with chuck key

(see Figure 8).

Chuck

Drill Bit

Chuck Key

Figure 8. Drill bit installed in chuck.

Adjusting Depth Stop

The depth stop allows you to drill holes to the same depth every time.

To adjust depth stop:

DISCONNECT TOOL FROM POWER!

2. Loosen set screw shown in Figure 10

before lowering bit to desired height.

3. Rotate lock ring counterclockwise until it stops (see Figure 10), then tighten set screw from Step 2 to secure depth.

Adjusting

Headstock Position

The headstock moves vertically and pivots around the column.

Model T32006 (Mfd. Since 01/20) -17-

Figure 10. Depth stop components.

Lock Ring

Choosing Spindle Speeds

Using Drill Bit Speed Chart

The chart shown in Figure 11 is intended as a generic guide only. Always follow the manufacturer's speed recommendations if provided with your drill bits. Exceeding the recommended speeds may be dangerous

Lubrication Suggestions

Wood .................................................. None

Plastics ...................................Soapy Water

Brass ......................Water-Based Lubricant

Aluminum .............Paraffin-Based Lubricant

Mild Steel .....................Oil-Based Lubricant

to the operator.

The speeds shown here are intended to get you started. The optimum speed will always depend on various factors, including tool diameter, drilling pressure, material hardness, material quality, and desired finish.

Larger bits turning at slower speeds tend to grab workpiece aggressively. This can result in operator's hand being pulled into bit or workpiece being thrown with great force. Always clamp workpiece to table

Often, when drilling materials other than

to prevent and reduce risk of injury.

wood, lubrication is necessary.

Twist/Brad

PointDrill Bits

1/16" － 3/16" 3000 2500 2500 2500 3000 2500

13/64" － 3/8" 2000 1500 2000 1250 2500 1250

25/64" － 5/8" 1500 750 1500 750 1500 600

11/16" － 1" 750 500 1000 400 1000 350

Spade/Forstner

Bits

1/4" － 1/2" 2000 1500

9/16" － 1" 1500 1250

1-1/8" － 1-7/8" 1000 750

2" － 3" 500 350

Hole Saws Soft Wood Hard Woods Plastic Brass Aluminum Mild Steel

1/2" － 7/8" 500 500 600 600 600 500

1" － 1-7/8" 400 400 500 500 500 400

2" － 2-7/8" 300 300 400 400 400 300

3" － 3-7/8" 200 200 300 300 300 200

4" － 5" 100 100 200 200 200 100

Rosette Cutters Soft Wood Hard Woods Plastic Brass Aluminum Mild Steel

Carbide Insert Type 350 250

One-Piece Type 1800 500

Soft Wood Hard Woods Plastic Brass Aluminum Mild Steel

Tenon/Plug Cutters Soft Wood Hard Woods Plastic Brass Aluminum Mild Steel

3/8" － 1/2" 1200 1000

5/8" － 1" 800 600

Figure 11. Drill bit speed chart (RPM).

Model T32006 (Mfd. Since 01/20)-18-

Changing

Spindle Speed

Loosen (4) lock nuts shown in Figure

14 to release motor pulley position and

belt tension.

The Model T32006 has a variable-speed spindle that operates up to 5000 RPM. This speed range is achieved using the variable-speed dial and the pulley system it controls.

Once you know the recommeded spindle speed for your project (see Choosing Spindle Speeds on Page 18), adjust the drive belt to the slowest speed range that provides the speed you need. This will allow for more control and extend your machine life.

Spindle

Pulley

Figure 12. Spindle speed chart.

To change speed ranges:

DISCONNECT TOOL FROM POWER!

2. Squeeze sides of headstock cover to remove (see Figure 13).

0-5000

0-3000 0-2000 R.P.M

Squeeze Tab

(1 of 2)

Motor

Pulley

x 4

Figure 14. Pulley nut locations.

— If excessively worn or damaged,

replace drive belt.

4. Adjust drive belt to desired pulley range (A-1 for 0-2000, B-2 for 0-3000, or C-3 for 0-5000) (see Figures 12 and 15).

Motor

Spindle

Pulley

Figure 15. Drive belt positioned on pulleys.

5. Position motor pulley where drive

belt has about 1⁄4" of deflection when pushed in the center (see Figure 16), then tighten lock nuts loosened in Step 3.

Pulley

Drive Belt

Pulley

Deflection

Figure 13. Headstock cover and squeeze

tab locations.

Model T32006 (Mfd. Since 01/20) -19-

Pulley

Figure 16. Checking strap deflection.

Attach headstock cover.

SECTION 6: ACCESSORIES

order online at www.grizzly.com or call 1-800-523-4777

SB1365—South Bend Way Oil-ISO 68

Engineered for the high pressur exert-

Installing unapproved accessories may cause tool to malfunction, resulting in serious personal injury or tool damage. To reduce this risk, only install accessories recommended for this tool by Grizzly.

Refer to our website or latest catalog for additional recommended accessories.

Basic Eye Protection

T20501—Face Shield Crown Protector 4" T20502—Face Shield Crown Protector 7" T20503—Face Shield Window T20451—"Kirova" Clear Safety Glasses T20452—"Kirova" Anti-Reflective Glasses T20456—DAKURA Safety Glasses

T20502

ed on horizontal and vertical ways and slides. Protects against rust and corrosion. Ensures stick-free, smooth motion which maximizes finishes and extends the life of your tool or machine. Won't gum up! 12 oz. AMGA#2 (ISO Equivalent)

Figure 18. Recommended lubrication

T32026—Drill Press Vise

This vise, designed specifically for the Model T32006, allows you to keep your hands well away from fast moving bits and cutters.

product.

G5978—Drill Press Vise 6"

T20503

T20456

Figure 17. Basic eye protection.

T20452

T20451

Made from high-grade cast iron, this hefty horizontal vise offers support and stability.

Figure 19. Model G5978 Drill Press Vise.

Model T32006 (Mfd. Since 01/20)-20-

SECTION 7: MAINTENANCE

Lubrication

An essential part of lubrication is cleaning the components before lubricating them.

This step is critical because grime and chips build up in lubricated components, which makes them hard to move. Simply

Always DISCONNECT POWER before servicing, adjusting, or doing maintenance to reduce risk of accidental injury or electrocution.

For optimum performance from this tool, this maintenance schedule must be strictly followed.

Ongoing

To minimize your risk of injury and maintain proper tool operation, shut down the tool immediately if you ever observe any of the items below and fix the problem before continuing operations.

• Loose mounting bolts.

• Worn switches.

• Worn or damaged wires.

• Damaged drive strip.

• Any other unsafe conditions.

adding more lubricant will not result in smooth moving parts. Clean components in this section before lubricating with recommended products like the one shown on Page 20.

DISCONNECT TOOL FROM POWER BEFORE PERFORMING LUBRICATION.

Quill & Column Surfaces

Oil Type .............. SB1365 or ISO 68 Equiv.

Oil Amount ...................................Thin Coat

Lubrication Frequency . . 8 Hrs. of Operation

Move the spindle all the way down to access the smooth surfaces of the quill (see Figure 20). Remove headstock from column to access entire length of column. Clean both with mineral spirits and rags.

Monthly Check

• Drive belt tension, damage, or wear.

• Clean/vacuum dust buildup off motor.

Cleaning

Cleaning the Model T32006 is relatively easy. Vacuum excess wood chips and sawdust, and wipe off the remaining dust with a dry cloth. If any resin has built up, use a resin dissolving cleaner to remove it.

Model T32006 (Mfd. Since 01/20) -21-

Figure 20. Location of quill and column

After cleaning, allow mineral spirits to dry, then apply a thin coat of oil to th e surfaces.

Column Surface

Quill Surface

surfaces.

SECTION 8: SERVICE

Troubleshooting

Motor & Electrical

Symptom Possible Cause Solution

Tool does not start, or power supply fuse/breaker trips immediately after startup.

Tool stalls or is underpowered.

Tool has vibration or noisy operation.

1. Power supply circuit breaker tripped or fuse blown.

2. Wiring broken, disconnected, or corroded.

3. Motor brushes worn/at fault.

4. Potentiometer/circuit board at fault.

5. ON/OFF switch at fault.

6. Motor at fault.

1. Feed rate too fast.

2. Tool undersized for task.

3. Improper workpiece material.

4. Belt too loose/has oil on it. Pulley slipping on shaft.

5. Motor overheated.

6. Motor brushes worn/at fault.

1. Motor or component loose.

2. Chuck or bit at fault.

3. Belt worn, loose, or pulleys misaligned.

4. Motor fan rubbing on fan cover.

5. Spindle bearings or spindle at fault.

6. Motor bearings at fault.

1. Reset circuit breaker or replace fuse.

2. Fix broken or disconnected/ corroded connections (Page

28).

3. Replace brushes (Page 25).

4. Replace potentiometer/ circuit board.

5. Replace switch.

6. Test/repair/replace.

1. Reduce feed rate (Page 19).

2. Use correct bit; reduce feed rate; use cutting fluid if necessary.

3. Use proper material type.

4. Tighten/clean belt. Tighten loose pulley.

5. Clean motor, let cool, and reduce workload.

6. Replace brushes (Page 25).

1. Replace damaged or missing bolts/nuts or tighten.

2. Replace unbalanced chuck; replace/resharpen bit; use correct feed rate.

3. Inspect/realign/replace belt (Page 19).

4. Fix/replace fan cover; replace loose/damaged fan.

5. Test by rotating spindle; grinding/loose shaft requires bearing replacement. Replace spindle.

6. Test by rotating shaft; grinding/loose shaft requires replacement.

Model T32006 (Mfd. Since 01/20)-22-

Drilling Operations

Symptom Possible Cause Solution

Tool falls out /loose in spindle/chuck.

Breaking tools or bits.

Workpiece or tool vibrates or chatters during operation.

Headstock is hard to raise.

Poor work results or tearout in holes.

Spindle overheats. 1. Spindle speed/feed rate

1. Tool loose or incorrectly installed.

2. Debris on tool or in spindle taper.

3. Taking too deep of a cut without clearing chips.

1. Spindle speed/feed rate too fast.

2. Taking too deep of a cut without clearing chips.

3. Improper drilling technique or type of cut.

4. Bit/tool getting too hot.

5. Spindle extended too far down while drilling.

1. Tool loose or incorrectly installed.

2. Spindle extended too far down while drilling.

3. Headstock height lock not tight.

4. Workpiece not secure.

5. Spindle speed/feed rate too fast.

1. Headstock locked.

2. Column dirty.

1. Spindle speed/feed rate too fast/too slow.

2. Dull or incorrect tool/bit.

3. Workpiece not secure.

4. Spindle extended too far down while drilling.

5. Excessive chips left in drill hole.

too fast.

2. Drill operated too long at high speeds.

1. Remove and re-install (Page 17).

2. Clean contaminants from tool and spindle taper, then re-install (Page 17).

3. Decrease depth of cut and allow chips to clear.

1. Reduce spindle speed (Page 19) or feed rate.

2. Decrease depth of cut and allow chips to clear.

3. Use right technique, tool, or machine for job.

4. Use coolant or oil for appropriate application (Page 18); reduce spindle speed (Page 19).

5. Retract spindle and lower headstock to increase rigidity.

1. Remove and re-install (Page 17).

2. Retract spindle and lower headstock to increase rigidity.

3. Tighten lock (Page 17).

4. Properly clamp workpiece.

5. Reduce spindle speed (Page 19); reduce feed rate.

1. Loosen headstock height lock (Page 17).

2. Clean column.

1. Adjust spindle speed (Page 19)/ feed rate.

2. Sharpen/replace bit/tool or select better tool for operation.

3. Properly secure workpiece.

4. Retract spindle and lower headstock to increase rigidity.

5. Retract drill bit frequently and allow chips to clear.

1. Reduce feed rate/cutting speed (Page 19).

2. Allow drill to cool, avoid operating at high speeds for extended time.

Model T32006 (Mfd. Since 01/20) -23-

Drilling Operations (Cont.)

Symptom Possible Cause Solution

Spindle does not fully retract.

Drill bit drifts. 1. Dull or incorrect bit/tool.

Drill bit stuck in workpiece.

Workpiece thrown from table.

Excessive runout or wobbling in chuck/drill bit.

Backside of workpiece splinters.

Review the trou bleshooting and procedures in this section if a problem develops with your tool. If you need replacement parts or additional help with a procedure, call our Technical Support.

1. Debris on spindle quill.

2. Worn spindle return spring.

2. Tool/bit loose or incorrectly installed.

1. Workpiece not secure.

2. Spindle speed/feed rate too fast or too slow.

1. Workpiece not secure.

2. Bit too large for feed speed.

1. Tool/bit bent or installed incorrectly.

2. Spindle bearings worn.

1. Scrap board not installed between table and workpiece.

1. Clean and lubricate quill surfaces (Page 21).

2. Replace spindle return spring.

1. Sharpen bit/tool or choose one that better suits the material.

2. Correctly install tool/bit (Page 17).

1. Properly clamp workpiece.

2. Adjust spindle speed (Page 19)/ feed rate.

1. Properly clamp workpiece.

2. Decrease feed speed or use a smaller bit.

1. Correctly install tool/bit (Page 17) or replace.

2. Replace spindle bearings.

1. Install scrap board between table and workpiece.

Replacing Motor Brushes

This tool is equipped with a universal motor that uses two carbon brushes to transmit electrical current inside the motor.

These brushes are considered to be regular "wear items" or "consumables" that will need to be replaced during the life of the motor. The frequency of required replacement is related to how much and how hard the motor is used.

Replace both carbon brushes at the same time when the motor no longer reaches full power, the motor has intermittent starting problems, or when the brushes measure less than 1⁄4" long (new brushes are 3⁄8" long).

Items Needed Qty.

Wrench or Socket 7mm ............................ 1

Hex Wrench 2mm ..................................... 1

Phillips Head Screwdriver #2 .................... 1

Carbon Brushes (PN PT320060041) ..1 Pr.

Model T32006 (Mfd. Since 01/20)-24-

To replace motor brushes:

1. DISCONNECT TOOL FROM POWER!

2. Remove headstock cover.

6. Pull out motor and press tabs on

motor wires to release wires, underlying springs, and motor brushes (see

Figure 23).

3. Remove drive belt. (Refer to Changing Spindle Speed on Page 19.)

4. Loosen spindle pulley set screw shown

in Figure 21 then remove pulley.

Spindle Pulley

Figure 21. Spindle pulley set screw

location.

5. Remove (2) Phillips head screws shown in Figure 22 to release motor from pulley system.

Motor Wire

(1 of 2)

Tab

(1 of 2)

Figure 23. Location of tabs securing motor

brushes.

7. Replace both motor brushes, and attach springs and motor wires.

8. Attach motor to pulley system with (2) screws removed in Step 5.

9. Install spindle pulley. Refer to Aligning Pulleys on Page 26 to ensure pulleys

are coplanar.

10. Install drive belt according to desired speed range (refer to Changing Spindle Speed on Page 19 for more information).

11. Install headstock cover.

Figure 22. Motor release screw locations.

Model T32006 (Mfd. Since 01/20) -25-

Aligning Pulleys

— If pulleys are aligned, proceed to

Step 8.

Pulley alignment is an important factor in power transmission and belt life. The pulleys should be parallel to each other and in the same plane (coplanar) for optimum performance.

Each pulley can be adjusted by loosening the set screws that secure them to their respective shafts.

Items Needed Qty.

Wrench or Socket 7mm ............................ 1

Straightedge 6" ......................................... 1

Hex Wrench 2mm ..................................... 1

To align pulleys:

1. DISCONNECT TOOL FROM POWER!

2. Remove headstock cover.

3. Place a straightedge on top of both

pulleys (see Figure 24) and check that they are aligned. There should be no space anywhere between straightedge or pulleys.

— If pulleys are not aligned, proceed

to Step 4.

4. Remove drive belt (refer to Changing Spindle Speed on Page 19).

5. Loosen set screw on motor pulley

shown in Figure 25.

Motor Pulley

Figure 25. Motor pulley set screw location.

6. Use straightedge to align pulleys, then tighten set screw from Step 5.

7. Install drive belt according to desired speed range (refer to Changing Spindle Speed on Page 19 for more

information).

Pulleys

Figure 24. Checking pulley alignment.

8. Install headstock cover.

Model T32006 (Mfd. Since 01/20)-26-

SECTION 9: WIRING

These pages are current at the time of printing. However, in the spirit of improvement, we may make changes to the electrical systems of future machines. Compare the manufacture date of your machine to the one

If there are differences between your machine and what is shown in this section, call Technical Support at

number and manufacture date of your

machine before calling. This information can be found on the main machine label.

stated in this manual, and study this section carefully.

(570) 546-9663 for assistance BEFORE making any changes to the wiring on your machine. An updated wiring diagram may be available. Note: Please gather the serial

Wiring Safety Instructions

SHOCK HAZARD. Working on wiring that

is connected to a power source is extremely dangerous. Touching electrified parts will result in personal injury including but not limited to severe burns, electrocution, or death. Disconnect the power from the machine before servicing electrical components!

MODIFICATIONS. Modifying the wiring beyond what is shown in the diagram may lead to unpredictable results, including serious injury or fire. This includes the installation of unapproved aftermarket parts.

WIRE CONNECTIONS. All connections must be tight to prevent wires from loosening during machine operation. Doublecheck all wires disconnected or connected during any wiring task to ensure tight connections.

CIRCUIT REQUIREMENTS. You MUST follow the requirements at the beginning of this manual when connecting your machine to a power source.

WIRE/COMPONENT DAMAGE. Damaged wires or components increase the risk of serious personal injury, fire, or machine damage. If you notice that any wires or components are damaged while performing a wiring task, replace those wires or components.

MOTOR WIRING. The motor wiring shown in these diagrams is current at the time of printing but may not match your machine. If you find this to be the case, use the wiring diagram inside the motor junction box.

CAPACITORS/INVERTERS. Some capacitors and power inverters store an electrical charge for up to 10 minutes after being disconnected from the power source. To reduce the risk of being shocked, wait at least this long before working on capacitors.

EXPERIENCING DIFFICULTIES. If you are experiencing difficulties understanding the information included in this section, contact our Technical Support at (570) 546-9663.

The photos and diagrams included in this section are best viewed in color. You can view these pages in color at www.grizzly.com.

Model T32006 (Mfd. Since 01/20) -27-

Wiring Diagram

HEADSTOCK

(viewed from right)

110 VAC

5-15 Plug

Neutral

Hot

Ground

SWITCH BOX

B500K

XD-1501

Circuit Board

Figure 26. T32006 electrical components.

MOTOR

(120V)

Figure 27. Potentiometer switch.

Model T32006 (Mfd. Since 01/20)-28-

SECTION 10: PARTS

Main

REF PART # DESCRIPTION REF PART # DESCRIPTION

1 PT32006001 SPINDLE PULLEY 7 PT32006007 QUILL 2 PT32006002 SET SCREW M4-.7 X 8 8 PT32006008 BALL BEARING 60002-2RS 3 PT32006003 FLAT HD SCR M4-.7 X 8 9 PT32006009 SPINDLE 4 PT32006004 MOTOR PULLEY COUPLER 10 PT32006010 COMPRESSION SPRING 2 X 35 X 42 5 PT32006005 EXT RETAINING RING 11MM 11 PT32006011 DRIVE BELT 5/32" X 9-5/8" 6 PT32006006 BALL BEARING 609Z 12 PT32006012 MOTOR PULLEY

Model T32006 (Mfd. Since 01/20) -29-

BUY PARTS ONLINE AT GRIZZLY.COM !

Scan QR co de to visit our Pa rts Store .

T32006 Machine Labels

(01/22/20)

• Scale= 1:1 (unless otherwise noted)

• Labels MUST be made of chemical-resistant material

Motor: 1/8 HP, 120V, 0.95A, 1-Ph, 60 Hz Max Distance Spindle to Column: 4-3/8" Max Distance Spindle to Table: 6-1/2" Spindle Speed Range: 0–5000 RPM Drilling Capacity Mild Steel: 3/16" Spindle Travel: 7/8" Spindle Taper: B10 Weight: 11 lbs.

Specifications

FOR GRIZZLY MACHINES ONLY! DO NOT REPRODUCE OR CHANGE THIS ARTWORK

WITHOUT WRITTEN APPROVAL!

Grizzly will not accept labels changed without approval. If

artwork changes are required, contact us immediately at manuals@grizzly.com.

GRIZZLY LOGO RED

PANTONE 711C or RAL 3020

PANTONE 151 C or RAL 2005

WARNING

COLOR CODES

GRIZZLY GREEN

PANTONE 568C

CAUTION

PANTONE 109 C

DANGER

PANTONE 485 C or RAL 3001

Mfd. for Grizzly in China

T32006

Date

Serial Number

To reduce the risk of serious injury when using this machine:

1. Read and understand owner’s manual before operating.

2. Always wear approved safety glasses.

3. Only plug power cord into a grounded outlet.

4. Disconnect power before setting up or servicing.

5. Avoid spindle entanglement. Tie back long hair, roll up long sleeves, and DO NOT wear loose clothing, gloves, or jewelry.

6. Keep all guards and covers in place during operation.

7. Clamp workpiece to table to prevent rotation.

8. Avoid putting hands near rotating bits.

9. Always remove chuck key and adjustment tools before starting.

10. Use correct speeds for drill bits and workpiece material.

11. Do not expose to rain or use in wet locations.

To reduce risk of death or serious injury, read manual BEFORE using machine.

Always wear ANSI-approved safety glasses and face shield when using this machine.

EYE/FACE INJURY

HAZARD!

ENTANGLEMENT

HAZARD!

WARNING!

Tie back long hair, and remove loose clothing to prevent getting caught in moving parts.

READ

MANUAL!

Always keep this cover closed during operation.

PINCH HAZARD!

WARNING!

INJURY/SHOCK HAZARD! Disconnect power before adjustments, maintenance, or service.

Main Parts List (Cont.)

REF PART # DESCRIPTION REF PART # DESCRIPTION

13 PT32006013 SET SCREW M4-.7 X 8 28 PT32006028 DOWNFEED LOCK RING 14 PT32006014 LOCK NUT M4-.7 29 PT32006029 SET SCREW M5-.8 X 10 15 PT32006015 FLAT WASHER 4MM 30 PT32006030 FOLDING HANDLE 110L, M8-1.25 X 15 16 PT32006016 MOTOR 1/8HP 120V 1-PH 31 PT32006031 HEADSTOCK 17 PT32006017 POWER CORD 18G 3W 72" 5-15P 32 PT32006032 DOWNFEED PINION GEAR 18 PT32006018 STRAIN RELIEF TYPE-1 5/8 33 PT32006033 LEVER SHAFT-DE M8-1.25 X 105, 10 19 PT32006019 HEX NUT M8-1.25 34 PT32006034 PHLP HD SCR M4-.7 X 40 20 PT32006020 FLAT WASHER 4MM 35 PT32006035 SWITCH BOX ASSEMBLY 21 PT32006021 PHLP HD SCR M4-.7 X 18 36 PT32006036 HEADSTOCK COVER 22 PT32006022 DRILL CHUCK B10 X 1/32-1/4" 37 PT32006037 KNOB M8-1.25, D30, BALL 23 PT32006023 DRILL CHUCK KEY 6MM STD 11T SD-9MM 38 PT32006038 HEX WRENCH 2MM 24 PT32006024 TABLE 39 PT32006039 HEX WRENCH 2.5MM 25 PT32006025 SET SCREW M8-1.25 X 8 40 PT32006040 HEX WRENCH 4MM 26 PT32006026 COLUMN 41 PT32006041 MOTOR BRUSH 27 PT32006027 COLUMN COVER

Labels & Cosmetics

WARNING!

INJURY/SHOCK

HAZARD! Disconnect power before adjustments, maintenance, or service.

101

104

T32006

Date

Serial Number

Mfd. for Grizzly in China

PINCH

HAZARD!

Always keep this cover closed during operation.

102

103

Specifications

To reduce the risk of serious injury when using this machine:

1. Read and understand owner’s manual before operating.

2. Always wear approved safety glasses.

3. Only plug power cord into a grounded outlet.

4. Disconnect power before setting up or servicing.

5. Tie back long hair, roll up long sleeves, and DO NOT wear loose clothing, gloves, or jewelry.

6. Keep all guards and covers in place during operation.

7. Clamp workpiece to table to prevent rotation.

8. Avoid putting hands near rotating bits.

9. Always remove any tools before starting.

10. Use correct speeds for drilling accessories and workpiece.

REF PART # DESCRIPTION REF PART # DESCRIPTION

101 PT32006101 INJURY/SHOCK HAZARD LABEL 105 PT32006105 SPECIFICATIONS LABEL 102 PT32006102 PINCH HAZARD LABEL 106 PT32006106 MACHINE WARNINGS LABEL 103 PT32006103 ELECTRICITY LABEL 107 PT32006107 TOUCH-UP PAINT, GRIZZLY GREEN 104 PT32006104 MACHINE ID LABEL 108 PT32006108 MANUAL/PPE/ENTANGLEMENT LABEL

11. Do not expose to rain or use in wet locations.

106

105

107

READ

MANUAL!

To reduce risk of death or serious injury, read manual BEFORE using machine.

WARNING!

EYE/FACE INJURY

HAZARD! Always wear ANSI-approved safety glasses and face shield when using this machine.

ENTANGLEMENT

HAZARD! Tie back long hair, and remove loose clothing to prevent getting caught in moving parts.

Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes off or becomes unreadable, the owner of this machine MUST replace it in the original location before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com.

BUY PARTS ONLINE AT GRIZZLY.COM !

Scan QR co de to visit our Pa rts Store .

Model T32006 (Mfd. Since 01/20)-30-

108

WARRANTY & RETURNS

Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty and any and all warranties that may be implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants. In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.

We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special, or consequential damages arising from the use of our products.

The manufacturers reserve the right to change specifications at any time because they constantly strive to achieve better quality equipment. We make every effort to ensure that our products meet high quality and durability standards and we hope you never need to use this warranty.

In the event you need to use this warranty, contact us by mail or phone and give us all the details. We will then issue you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the carton. We will not accept any item back without this number. Proof of purchase must accompany the merchandise.

Please feel free to write or call us if you have any questions about the machine or the manual.

Thank you again for your business and continued support. We hope to serve you again soon.

warranty-card

registration page

take advantage of this warranty, you must register it at https://www.grizzly.com/secureforms/

, or you can scan the QR code below to be automatically directed to our warranty

. Enter all applicable information for the product.

WARRANTY

Model T32006 (Mfd. Since 01/20) -31-

Grizzly T32006 User guide

Specifications and Main Features

Frequently Asked Questions

User Manual